The manufacturer shall submit to the approval authority an application for EC type-approval of a vehicle with regard to emissions.
The application referred to in paragraph 1 shall be drawn up in accordance with the model of the information document set out in Appendix 3 to Annex I.
In addition, the manufacturer shall submit the following information:
in the case of vehicles equipped with positive-ignition engines, a declaration by the manufacturer of the minimum percentage of misfires out of a total number of firing events that either would result in emissions exceeding the OBD thresholds laid out in Table 4A of paragraph 6.8.2 of UN Regulation No 154 if that percentage had been present from the start of a type 1 test as chosen for the demonstration in accordance with Annex C5 to UN Regulation No 154 or could lead to an exhaust catalyst, or catalysts, overheating prior to causing irreversible damage;
detailed written information fully describing the functional operation characteristics of the OBD system, including a listing of all relevant parts of the emission control system of the vehicle that are monitored by the OBD system;
a description of the malfunction indicator used by the OBD system to signal the presence of a fault to a driver of the vehicle;
a declaration by the manufacturer that the OBD system complies with the provisions of section 1 of Appendix 1 to Annex XI relating to in-use performance under all reasonably foreseeable driving conditions;
a plan describing the detailed technical criteria and justification for incrementing the numerator and denominator of each monitor that must fulfil the requirements of paragraphs 7.2 and 7.3. of Appendix 1 to Annex C5 of UN Regulation No 154, as well as for disabling numerators, denominators and the general denominator under the conditions outlined in paragraph 7.7 of Appendix 1 to Annex C5 of UN Regulation No 154;
a description of the provisions taken to prevent tampering with and modification of the emission control systems, including the emission control computer and odometer including the recording of mileage values for the purposes of the requirements of Annexes XI and XVI;
if applicable, the particulars of the vehicle family as referred to in paragraph 6.8.1. of UN Regulation No 154;
where appropriate, copies of other type-approvals with the relevant data to enable extension of approvals and establishment of deterioration factors.
For the purposes of point (d) of paragraph 3, the manufacturer shall use the model of manufacturer's certificate of compliance with the OBD in-use performance requirements set out in Appendix 7 of Annex I
For the purposes of point (e) of paragraph 3, the approval authority that grants the approval shall make the information referred to in that point available to the approval authorities or the Commission upon request.
For the purposes of paragraph 3, points (d) and (e), approval authorities shall not approve a vehicle if the information submitted by the manufacturer is inappropriate for fulfilling the requirements of section 1 of Appendix 1 to Annex XI.
Paragraphs 7.2, 7.3 and 7.7 of Appendix 1 to Annex C5 of UN Regulation No 154 shall apply under all reasonably foreseeable driving conditions.
For the assessment of the implementation of the requirements set out in these paragraphs, the approval authorities shall take into account the state of technology.
For the purposes of point (f) of paragraph 3, the provisions taken to prevent tampering with and modification of the emission control computer shall include the facility for updating using a manufacturer-approved programme or calibration.
For the tests specified in Figure I.2.4 of Annex I the manufacturer shall submit to the technical service responsible for the type-approval tests a vehicle representative of the type to be approved.
The application for type-approval of mono fuel, bi-fuel and flex-fuel vehicles shall comply with the additional requirements laid down in Sections 1.1 and 1.2 of Annex I.
Changes to the make of a system, component or separate technical unit that occur after a type-approval shall not automatically invalidate a type approval, unless its original characteristics or technical parameters are changed in such a way that the functionality of the engine or pollution control system is affected.
In order for the approval authorities to be able to assess the proper use of AES, taking into account the prohibition of defeat devices contained in Article 5(2) of Regulation (EC) No 715/2007, the manufacturer shall also provide an extended documentation package, as described in Appendix 3a of Annex I to this Regulation.
For vehicles approved under the character EB and EC as defined in Table 1, Appendix 6 to Annex I, the manufacturer shall introduce an indicator (AES Flag or Timer) to indicate when a vehicle runs in AES mode instead of BES mode. The indicator shall be available via the serial port of a standard diagnostic connector upon request of a generic scan-tool. The AES that is running shall be identifiable via the formal documentation package.
The extended documentation package shall be identified and dated by the approval authority and kept by that authority for at least 10 years after the approval is granted.
At the request of the manufacturer, the approval authority shall conduct a preliminary assessment of the AES for new vehicle types. In that case, the relevant documentation shall be provided to the type approval authority between 2 and 12 months before the start of the type-approval process.
The approval authority shall make a preliminary assessment on the basis of the extended documentation package, as described in point (b) of Appendix 3a to Annex I, provided by the manufacturer. The approval authority shall make the assessment in accordance with the methodology described in Appendix 3b of Annex I. The approval authority may deviate from that methodology in exceptional and duly justified cases.
The preliminary assessment of the AES for new vehicle types shall remain valid for the purposes of type approval for a period of 18 months. That period may be extended by a further 12 months if the manufacturer provides to the approval authority proof that no new technologies have become accessible in the market that would change the preliminary assessment of the AES.
The approval authority may test the functioning of AES.
A list of AES which were deemed non-acceptable by type approval authorities shall be compiled yearly by the Forum for Exchange of Information on Enforcement and made available to the public by the Commission at the latest by end of March of the following year, in case there were AES which were deemed non-acceptable.
The manufacturer shall also provide to the approval authorities a formal documentation package, as in Appendix 3a to Annex I, containing information on AES/BES that would allow an independent tester to identify if the emissions measured can be attributed to an AES or BES strategy or are potentially due to a defeat device. The formal documentation package shall be made available to all type approval authorities, technical services, market surveillance authorities, third parties and the Commission upon request.
Vehicles of category M1 or N1 shall be approved with emission characters EA, EB or EC as specified in Table 1, Appendix 6 to Annex I, taking into account the utility factors determined in accordance with the values specified in Table A8.App5/1 of point 3.2. of Annex XXI.
The extended documentation package referred to in paragraph 11 (a) and (b) shall remain strictly confidential. It may be kept by the approval authority, or, at the discretion of the approval authority, may be retained by the manufacturer. In the case the manufacturer retains the documentation package, that package shall be identified and dated by the approval authority once reviewed and approved. It shall be made available for inspection by the approval authority at the time of approval or at any time during the validity of the approval.
The manufacturer shall also provide the type approval authority which granted the emission type-approval under this Regulation (‘granting type approval authority’) with a package on testing transparency containing the necessary information in order to allow the performance of testing in accordance with point 5.9 of Annex II.
Once the electronic platform for ISC is ready, the manufacturer shall also upload all required data into the platform for all its vehicles. The information in the transparency lists shall be limited to the prescribed information required by Appendix 5 of Annex II.