ANNEX V, Regulation (EU) 2016/1788

In forcesince 14 Jul 2016

Annexes I, III, V, VII, X, XII to XV, XVII, XIX, XX, XXII, XXV to XXXI, XXXIII and XXXIV to Delegated Regulation (EU) 2015/208 are amended as follows:

(1)

Annex I is amended as follows:

(a)

above the row with Regulation Number 3, the following row is inserted:

‘1 | Lighting installation | Incorporating all valid text up to 02 series of amendments | OJ L 177, 10.7.2010, p. 1 | T and C’;

(b)

above the row with Regulation Number 7, the following row is inserted:

‘6 | Lighting, light signalling devices and their light sources |

Supplement 18 to the 01 series of amendments

Corrigendum 1 to Supplement 18

Supplement 19 to the 01 series of amendments

OJ L 177, 10.7.2010, p. 40 | T, C, R and S’;

(c)

above the row with Regulation Number 10, the following row is inserted:

‘8 | Lighting installation |

Incorporating all valid text up to 05 series of amendments

Corrigendum 1 to Revision 4 of the Regulation

OJ L 177, 10.7.2010, p. 71 | T and C’;

(d)

above the row with Regulation Number 21, the following row is inserted:

‘20 | Lighting installation | Incorporating all valid text up to 03 series of amendments | OJ L 177, 10.7.2010, p. 170 | T and C’;

(e)

above the row with Regulation Number 25, the following row is inserted:

‘23 | Lighting, light signalling devices and their light sources | Supplement 17 to the original version of the Regulation | OJ L 4, 7.1.2012, p. 18 | T, C, R and S’

(f)

above the row with Regulation Number 79, the following row is inserted:

‘77 | Lighting installation | Supplement 14 to the original version of the Regulation | OJ L 4, 7.1.2012, p. 21 | T, C, R and S’;

(2)

in Annex III, point 2.6 is replaced by the following:

‘2.6. In order for approval authorities may calculate their maximum theoretical speed, the manufacturer shall specify as a guide the gear ratio, the actual forward movement of the powered wheels corresponding to one complete revolution, and the rpm at maximum power output or the cut-off initiation speed under full load with the throttle fully open, whichever is higher, and the speed governor, if fitted, adjusted as laid down by the manufacturer. The maximum theoretical speed shall be calculated without the tolerances referred to in point 2.5.’

(3)

Annex V is amended as follows:

(a)

section 1 is replaced by the following:

For the purposes of this Annex, the definitions in section 1 of Annex XXXIII shall apply. The following definitions shall also apply:’

(b)

point 2.3 is amended as follows:

(i)

the first sentence is replaced by the following:

‘The requirements set out in point 2.2 are not applicable to C-category tractors with steel track chains equipped with differential steering.’

(ii)

the third sentence is replaced by the following:

‘If the steering system is combined with the braking system, the requirements laid down in Commission Delegated Regulation (EU) 2015/68 [Commission Delegated Regulation (EU) 2015/68 of 15 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle braking requirements for the approval of agricultural and forestry vehicles (OJ L 17, 23.1.2015, p. 1).’] shall apply.

(c)

in point 3.4.1.1 the fourth sentence is replaced by the following:

‘Without prejudice to the requirements laid down in Delegated Regulation (EU) 2015/68, if there is a hydraulic connection between the hydraulic steering equipment and the hydraulic braking equipment, and if both are supplied from the same energy source, the force required to activate the steering equipment shall not exceed 40 daN if either of the systems should fail.’

(4)

in Annex VII, point 2 is replaced by the following:

‘2. The part concerning the vision beside the tractor, in ISO 5721-2:2014 on the field of vision to the side and to the rear of agricultural tractors. The requirements of point 5.1.3 of ISO 5721-2:2014 may be fulfilled by a combination of direct and indirect view.’

(5)

Annex X is replaced by the following:

(6)

Annex XII is amended as follows:

(a)

section 3 is replaced by the following:

The templates of the documents referred to in points 2.1 to 2.4, to be submitted during the EU type-approval process, shall be those set out in Annex I of Implementing Regulation (EU) 2015/504.’

(b)

section 4 is replaced by the following:

Each vehicle approved in accordance with the requirements set out in this Annex shall be assigned an approval number and marking, in accordance with the model set out in Annex IV of Implementing Regulation (EU) 2015/504.’

(c)

points 6.1 and 6.1.1 are replaced by the following:

6.1.1. Presence: Mandatory for tractors with maximum design speed exceeding 40 km/h. Optional for other tractors. Main-beam headlamps are prohibited on R- and S-category vehicles. Main-beam head lamps, as prescribed in UNECE Regulation No 1, as referenced in Annex I, are only allowed on tractors with maximum design speed not exceeding 40 km/h. Main-beam head lamps, as prescribed in UNECE Regulations Nos 1, 8 and 20, as referenced in Annex I, are only allowed on new tractor types until 31 December 2020 and are only allowed on new tractors until 31 December 2022.’

(d)

point 6.2 is replaced by the following:

‘6.2. Dipped-beam headlamps (UNECE Regulations Nos 1, 8, 20, 98, 112 and 113, as referenced in Annex I to this Regulation)’;

(e)

point 6.2.1 is replaced by the following:

‘6.2.1. Presence: Tractors shall be equipped with dipped-beam headlamps. Dipped-beam headlamps are prohibited on R- and S-category vehicles. Dipped-beam head lamps, as prescribed in UNECE Regulation No 1, as referenced in Annex I, are only allowed on tractors with maximum design speed not exceeding 40 km/h. Dipped-beam head lamps, as prescribed in UNECE Regulations Nos 1, 8 and 20, as referenced in Annex I, are only allowed on new tractor types until 31 December 2020 and are only allowed on new tractors until 31 December 2022.’

(f)

point 6.25.5.1.2 is replaced by the following:

‘6.25.5.1.2. The other two retro-reflectors shall keep within a maximum height of 2500 mm above the ground and shall comply with point 6.25.5.1.’

(7)

Annex XIII is amended as follows:

(a)

in section 1, the second paragraph is replaced by the following:

‘Definitions for the protection of drive components, in accordance with the requirements laid down in Article 20 of Commission Delegated Regulation (EU) No 1322/2014 [Commission Delegated Regulation (EU) No 1322/2014 of 19 September 2014 supplementing and amending Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle construction and general requirements for the approval of agricultural and forestry vehicles (OJ L 364, 18.12.2014, p. 1).’], are valid for this Annex.

(b)

in Part 2, point 1.1 is replaced by the following:

‘1.1. Interior parts of the passenger compartment excluding the side doors, with all doors, windows and access lids in the closed position’;

(c)

in point 1.1.3.2 of Part 2, the following sentence is added:

‘This requirement shall not apply to parts of control devices and of casings between their switches, which protrude less than 5 mm, but the outward facing angles of such parts shall be blunted, save where such parts protrude less than 1,5 mm.’

(d)

in point 3.1 of Part 2, the second paragraph is replaced by the following:

‘If the panels and components, etc., are covered with materials softer than 60 Shore A hardness, the procedure for the measuring of projections described in the first paragraph shall apply only after the removal of such materials.’

(e)

in section 4 of Part 2, the heading is replaced by the following:

‘Apparatus and procedure for application of points 1.1.3 and 1.1.4’;

(f)

Part 4 is replaced by the following:

The requirements laid down in Article 21 of Delegated Regulation (EU) No 1322/2014 shall apply.’

(8)

Annex XIV is replaced by the following:

(9)

in Annex XV, Part 2 is amended as follows:

(a)

points 1.1.1 and 1.1.2 are replaced by the following:

‘1.1.1. The application for approval of a vehicle type, with regard to its electromagnetic compatibility pursuant to Articles 24 and 26 of Regulation (EU) No 167/2013 and Annex I to Implementing Regulation (EU) 2015/504 shall be submitted by the vehicle manufacturer.

1.1.2. The vehicle manufacturer shall submit the information document, the model of which is set out in Annex I to Implementing Regulation (EU) 2015/504.’

(b)

in point 1.1.4, the second sentence is replaced by the following:

‘This vehicle shall represent the vehicle type specified in the information document set out in Article 2 of Implementing Regulation (EU) 2015/504.’

(c)

in point 1.2.1, the first sentence is replaced by the following:

‘The application for approval of a type of ESA with regard to its electromagnetic compatibility pursuant to Articles 24 and 26 of Regulation (EU) No 167/2013 and Article 2 of Implementing Regulation (EU) 2015/504 shall be submitted by the vehicle manufacturer or by the manufacturer of the ESA.’

(d)

point 1.2.2 is replaced by the following:

‘1.2.2. The vehicle manufacturer shall submit the information document, the model of which is set out in Annex I to Implementing Regulation (EU) 2015/504.’

(e)

point 1.2.6 is replaced by the following:

‘1.2.6. Where applicable, any restrictions on use shall be identified. Any such restrictions shall be included in the information document referred to in Article 2 of Implementing Regulation (EU) 2015/504 or in the EU type-approval certificate referred to in Annex V of Implementing Regulation (EU) 2015/504.’

(f)

point 2.1 is replaced by the following:

‘2.1. Every ESA conforming to a type approved pursuant to this Regulation shall bear an EU type-approval mark in accordance with Article 5 of Implementing Regulation (EU) 2015/504 and Annex XX to this Regulation.’

(g)

point 3.3.2.4 is replaced by the following:

‘3.3.2.4. Notwithstanding the limits defined in points 3.3.2.1, 3.3.2.2 and 3.3.2.3, if, during the initial step described in point 1.3 of Part 4, the signal strength measured at the vehicle broadcast radio antenna is less than 20 dB microvolts/m (10 microvolts/m) over the frequency range 88 to 108 MHz, then the vehicle shall be deemed to comply with the limits for narrowband emissions and no further testing shall be required.’

(10)

in Annex XVII, points 1.1 and 1.2 are replaced by the following:

‘1.1. Tractors with cab shall be fitted with a heating system which complies with this Annex. Tractors with cab may be fitted with air conditioning systems. Where fitted, such systems shall comply with this Annex.

1.2. The heating system, in combination with the cab ventilation, shall be able to defrost and demist the windscreen. Heating and cooling systems shall be tested in accordance with sections 8 and 9, paragraphs 8.1.1 to 8.1.4 and 9.1.1 to 9.1.4 of ISO 14269-2:2001, respectively. During the test, system controls shall be set according to the manufacturer's specifications. The test reports shall be included into the information document.’

(11)

Annex XIX is amended as follows:

(a)

point 2.6.1 is replaced by the following:

‘2.6.1. If the height of the upper edge of the plate from the ground surface does not exceed 1,20 m, the plate shall be visible in the whole space included within the following four planes:

(a)

the two vertical planes touching the two lateral edges of the plate and forming an angle measured outwards to the left and to the right of the plate of 30o to the longitudinal median plane of the vehicle;

(b)

the plane touching the upper edge of the plate and forming an angle measured upwards of 15o to the horizontal;

(c)

the horizontal plane through the lower edge of the plate.’

(b)

the following point 2.6.1.a is inserted:

‘2.6.1.a. If the height of the upper edge of the plate from the ground surface exceeds 1,20 m, the plate shall be visible in the whole space included within the following four planes:

(a)

the two vertical planes touching the two lateral edges of the plate and forming an angle measured outwards to the left and to the right of the plate of 30o to the longitudinal median plane of the vehicle;

(b)

the plane touching the upper edge of the plate and forming an angle measured upwards of 15o to the horizontal;

(c)

the plane touching the lower edge of the plate and forming an angle measured downwards of 15o to the horizontal.’

(c)

point 2.6.2 is replaced by the following:

‘2.6.2. No structural element, even when fully transparent, shall be located in the space described in points 2.6.1 and 2.6.1a.’

(12)

Annex XX is amended as follows:

(a)

points 2.1 and 2.2 are replaced by the following:

‘2.1. All agricultural or forestry vehicles shall be provided with the plate and inscriptions described in the following points. The plate and inscriptions shall be attached by the manufacturer.

2.2. All components or separate technical units conforming to a type approved pursuant to Regulation (EU) No 167/2013 shall bear an EU type-approval mark described in point 6 of this Annex or a mark provided in Article 34(2) of that Regulation and set out in Article 5 of Implementing Regulation (EU) 2015/504.’

(b)

points 3.1 and 3.2 are replaced by the following:

‘3.1. A statutory plate, modelled as set out in Annex IV to Implementing Regulation (EU) 2015/504, shall be firmly attached in a conspicuous and readily accessible position on a part normally not subject to replacement during normal use, regular maintenance or repair (e.g. due to accident damage). It shall show clearly and indelibly the information specified in the model for the EU type-approval mark set out in Annex IV to Implementing Regulation (EU) 2015/504.

3.2. The manufacturer may give additional information below or to the side of the prescribed inscriptions, outside a clearly marked rectangle enclosing only the information required by Annex IV of Implementing Regulation (EU) 2015/504.’

(c)

point 4.3 is replaced by the following:

‘4.3. It shall be marked on the chassis or other similar structure, where possible on the front right-hand side of the vehicle.’

(d)

section 5 is replaced by the following:

The characters specified in the model for the EU type-approval mark set out Annex IV to Implementing Regulation (EU) 2015/504 shall be used for the markings referred to in sections 3 and 4.’

(e)

in section 6, the first sentence is replaced by the following:

‘Every separate technical unit or component, conforming to a type in respect of which EU separate technical unit or component type-approval has been granted in accordance with Chapter V of Regulation (EU) No 167/2013, shall bear an EU separate technical unit or component type-approval mark, pursuant to Article 34(2) of that Regulation and in accordance with Article 5 of Implementing Regulation (EU) 2015/504.’

(13)

Annex XXII is amended as follows:

(a)

in point 1, the second paragraph is replaced by the following:

‘For the purposes of this Annex, definitions of ‘drawbar towed vehicle’ and ‘rigid drawbar towed vehicle’, set out in Article 2 of Delegated Regulation (EU) 2015/68, shall apply.

The following definitions shall also apply:’

(b)

point 1.2 is replaced by the following:

‘1.2. ‘Technically permissible maximum mass per axle’ means the mass corresponding to the maximum permissible static vertical load transmitted to the ground by the wheels of the axle or track undercarriages, on the basis of the construction features of the axle and of the vehicle and their design performances irrespective from the load capacity of the tyres or tracks.’

(c)

point 2.3.2 is replaced by the following:

‘2.3.2. For vehicles of categories R and S imposing a significant static vertical load on the tractor (rigid drawbar towed vehicle and centre-axle towed vehicle), the maximum permissible mass of the vehicle shall be considered to be the sum of the maximum permissible masses per axle and shall be applicable for type-approval purposes, instead of the corresponding maximum permissible mass mentioned in the third column of Table 1. The significant static vertical load on the tractor shall be taken into account in the type-approval of the tractor as laid down in point 2.3.1.’

(14)

in section 3 of Annex XXV, the second paragraph is replaced by the following:

‘If necessary, measure(s) for charge dissipation shall be provided. However, no charge dissipation system is required for fuel tanks designed for containing a fuel with a flash point of at least 55 °C. The flash point shall be determined in accordance with ISO 2719:2002.’

(15)

in Annex XXVI, section 1 is replaced by the following:

Vehicles of category R covered by this Regulation shall be designed so as to provide effective protection against underrunning from the rear by vehicles of categories M1 and N1 [As defined in Part A of Annex II to Directive 2007/46/EC.’]. They shall comply with the requirements set out in sections 2 and 3 of this Annex, shall be granted a type-approval certificate set out in Annex V to Implementing Regulation (EU) 2015/504 and the EU type-approval mark, set out in point 5.2 of Annex IV to that Regulation, shall be affixed to the rear protective structure.

(16)

in Annex XXVII, points 2.4.1.1 and 2.4.1.2 are replaced by the following:

‘2.4.1.1. on a drawbar trailer: not more than 500 mm to the rear of the transverse vertical plane tangential to the rearmost part of the tyre on the wheel immediately forward of the guard;

2.4.1.2. on a rigid drawbar trailer or centre-axle trailer: in the area forward of the transverse plane passing through the centre of the front axle but not more than the front of the bodywork, if any, to ensure the normal manoeuvrability of the trailer.’

(17)

in Annex XXVIII, section 7 is replaced by the following:

7.1. For tractors of category T4.3, the length of the platform shall not exceed 2,5 times the maximum front or rear track of the tractor, whichever is the larger.

7.2. For tractors of category T2, the length of the platform shall not exceed 1,8 times the maximum front or rear track of the tractor, whichever is the larger.’

(18)

Annex XXIX is amended as follows:

(a)

in section 3, the first paragraph is replaced by the following:

‘The towing device shall be of the slotted-jaw type or a winch suitable for its application. The opening at the centre of the locking pin shall be 60 mm + 0,5/– 1,5 mm and the depth of the jaw measured from the centre of the pin shall be 62 mm - 0,5 / +5 mm.’

(b)

section 5 is replaced by the following:

The correct use of the towing device shall be explained in the Operator’s manual, in accordance with the requirements laid down in Article 25 of Delegated Regulation (EU) No 1322/2014.’

(19)

Annex XXX is amended as follows:

(a)

point 2.2.4.3 is replaced by the following:

‘2.2.4.3. The relevant information concerning load and speed indices as well as the applicable tyre inflation pressures shall be stated clearly in the instruction manual of the vehicle in order to ensure that suitable replacement tyres with an appropriate load capacity shall be fitted when necessary, once the vehicle has been put into service.’

(b)

point 2.2.6.2 is replaced by the following:

‘2.2.6.2. In case of “Improved Flexion Tyre” or “Very High Flexion Tyre” classified in category of use “Tractor – Drive wheel” (marked with prefix IF or VF) operated at speeds up to a maximum speed of 10 km/h fitted to a vehicle equipped with a “Front end loader”, the maximum load on a tyre shall not exceed 1,40 times the load corresponding to the load index marked on the tyre and the relevant reference pressure shall be increased by 80 kPa.’

(c)

point 2.2.6.3 is replaced by the following:

‘2.2.6.3. Where tyres classified in category of use “Tractor – Drive wheel” are marked with speed symbols D or A8 and fitted to agricultural trailers operating at speeds between 25 km/h and 40 km/h, the maximum load on a tyre shall not exceed 1,20 times the load corresponding to the load index marked on the tyre.’

(20)

in Annex XXXI, point 1.1 is replaced by the following:

‘1.1. Tb and Rb category vehicles shall be equipped with wheel guards (parts of the bodywork, mudguards, etc.).’

(21)

Annex XXXIII is amended as follows:

(a)

points 1.1, 1.2 and 1.3 are replaced by the following:

‘1.1. “Track undercarriage” means a system comprising at least two of the following items: track rollers, track idler and track driver, with a continuous track chain or track belt running around them.

1.2. “Track rollers” means the cylinders in the track undercarriage that transmit the mass of the vehicle and track undercarriage to the ground via the track belt or track chain.

1.3. “Track belt” means a continuous flexible rubber like belt, reinforced internally to enable the tractive forces.’

(b)

the following points 1.6, 1.7, 1.8 and 1.9 are inserted:

‘1.6. “Track idler” means sprockets or pulleys in the track undercarriage that do not transmit torque to the track belt or track chain, their main function being the tensioning of the track chain or track belt; track idlers may also create the ramp up/down angles in the track geometry.

1.7. “Track driver” means the sprocket or cage wheel in the track undercarriage that transmit torque from the vehicle drive system to the track belt or track chain.

1.8. “Track chain” means a continuous metallic chain which engages with the track driver and where each link is with a transversal metallic track shoe, the latter optionally padded with a rubber strip for road surface protection.

1.9. Figures illustrating definitions set out in points 1.2, 1.6 and 1.7:

(c)

points 2.1.1, 2.1.2 and 2.1.3 are replaced by the following:

‘2.1.1. Vehicles with maximum design speed not exceeding 15 km/h shall be equipped either with track chains or with track belts.

2.1.2. Vehicles with a maximum design speed exceeding 15 km/h and not exceeding 40 km/h shall be equipped with track belts only.

2.1.3. Vehicles with a maximum design speed exceeding 40 km/h shall be equipped with track belts only.’

(d)

points 3.1 and 3.2 are replaced by the following:

‘3.1. Vehicles with a maximum design speed of not less than 15 km/h shall be equipped with track belts.

3.2. Track undercarriages shall be non-damaging to roads. Vehicles with track undercarriages are non-damaging to roads if the limits set out in points 3.3 to 3.5 are not exceeded and the contact surface of the track undercarriage with the road pavement is composed of an elastomeric material (such as rubber, etc.).’

(e)

point 3.3.1 is replaced by the following:

‘3.3.1. Track chains’;

(f)

point 3.3.1.2 is replaced by the following:

This article is long: the rest is at the official publication.