ANNEX IC, Regulation (EC) No 1013/2006 of the European Parliament and of the Council of 14 June 20…

In forcesince 11 Jan 2021

1.

The present instructions provide the necessary explanations for completing the notification and movement documents. Both documents are compatible with the Basel Convention [Basel Convention on the Control of Transboundary Movements of Hazardous Wastes and Their Disposal, 22 March 1989. See www.basel.int], the OECD Decision [Decision C(2001)107/FINAL of the OECD Council, concerning the revision of Decision C(92)39/FINAL on the control of transboundary movements of waste destined for recovery operations; the former Decision is a consolidation of texts adopted by the Council on 14 June 2001 and on 28 February 2002 (with amendments). See http://www.oecd.org/department/0,2688,en_2649_34397_1_1_1_1_1,00.html] (which only covers shipments of wastes destined for recovery operations within the OECD area) and this Regulation, since they take into account the specific requirements set out in these three instruments. Because the documents have been made broad enough to cover all three instruments, however, not all blocks in the document will be applicable to all of the instruments and it therefore may not be necessary to complete all of the blocks in a given case. Any specific requirements relating to only one control system have been indicated with the use of footnotes. It is also possible that national implementing legislation may use terminology that differs from that adopted in the Basel Convention and the OECD Decision. For example, the term ‘shipment’ is used in this Regulation instead of ‘movement’ and the titles of the notification and movement documents therefore reflect this variation by employing the term ‘movement/shipment’.

2.

The documents include both the term ‘disposal’ and ‘recovery’, because the terms are defined differently in the three instruments. The European Community Regulation and the OECD Decision use the term ‘disposal’ to refer to disposal operations listed in Annex IV.A of the Basel Convention and Appendix 5.A of the OECD Decision and ‘recovery’ for recovery operations listed in Annex IV.B of the Basel Convention and Appendix 5.B of the OECD Decision. In the Basel Convention itself, however, the term ‘disposal’ is used to refer to both disposal and recovery operations.

3.

The competent authorities of dispatch are responsible for providing and issuing the notification and movement documents (in both paper and electronic versions). When doing so, they will use a numbering system, which allows a particular consignment of waste to be traced. The numbering system should be prefixed with the country code of the country of dispatch that can be found in the ISO standard 3166 abbreviation list. Within the EU, the two-digits country code must be followed by a space. This may be followed by an optional code of up to four digits specified by the competent authority of dispatch followed by a space. The numbering system must end with a six-digit number. For illustration, if the country code is XY and the six-digit number 123456, the notification number would be XY 123456 if no optional code were specified. Where an optional code, for example 12, is specified, the notification number would be XY 12 123456. However, in case a notification or movement document is transmitted electronically and no optional code is specified, ‘0000’ should be inserted instead of the optional code (e.g. XY 0000 123456); in case an optional code of less than four digits is specified, for example 12, the notification number would be XY 0012 123456.

4.

Countries may wish to issue the documents in a paper size format that conforms to their national standards (normally ISO A4, as recommended by the United Nations). In order to facilitate their use internationally, however, and to take into account the difference between ISO A4 and the paper size used in North America, the frame size of the forms should not be greater than 183 × 262 mm with margins aligned at the top and the left side of the paper. The notification document (block 1-block 21 including footnotes) should be on one page and the list of abbreviations and codes used in the notification document should be on a second page. With regard to the movement document, block 1-block 19 including footnotes should be on one page and block 20-22 and the list of abbreviations and codes used in the movement document should be on a second page.

5.

The notification document is intended to provide the competent authorities concerned with the information they need to assess the acceptability of proposed waste shipments. It also provides space for them to acknowledge receipt of the notification and, where required, to consent in writing to a proposed shipment.

6.

The movement document is intended to travel with a consignment of waste at all times from the moment it leaves the waste producer to its arrival at a disposal or recovery facility in another country. Each person who takes charge of a shipment (carriers and possibly consignee [Outside the European Community, the term ‘importer’ may be used instead of ‘consignee’.]) is to sign the movement document either upon delivery or receipt of the wastes in question. There are also spaces in the movement document for recording passage of the consignment through the customs offices of all countries concerned (required by this Regulation). Finally, the document is to be used by the relevant disposal or recovery facility to certify that the waste has been received and that the recovery or disposal operation has been completed.

7.

A planned shipment subject to the procedure of prior written notification and consent may take place only after the notification and movement documents have been completed pursuant to this Regulation, taking into account Articles 16(a) and 16(b), and during the period of validity of the written or tacit consents of all competent authorities concerned.

8.

Those filling out printed copies of the documents should use typescript or block capitals in permanent ink throughout. Signatures should always be written in permanent ink and the name of the authorised representative should accompany the signature in capital letters. In the event of a minor mistake, for example the use of the wrong code for a waste, a correction can be made with the approval of the competent authorities. The new text must be marked and signed or stamped, and the date of the modification must be noted. For major changes or corrections, a new form must be completed.

9.

The forms have also been designed to be easily completed electronically. Where this is done, appropriate security measures should be taken against any misuse of the forms. Any changes made to a completed form with the approval of the competent authorities should be visible. When using electronic forms transmitted by e-mail, a digital signature is necessary.

10.

To simplify translation, the documents require a code, rather than text, for the completion of several blocks. Where text is required, however, it must be in a language acceptable to the competent authorities in the country of destination and, where required, to the other concerned authorities.

11.

A six-digit format should be used to indicate the date. For example, 29 January 2006 should be shown as 29.01.06 (Day.Month.Year).

12.

Where it is necessary to add annexes to the documents providing additional information, each annex should include the reference number of the relevant document and cite the block to which it relates.

13.

The notifier [Outside the European Community, the term ‘exporter’ may be used instead of ‘notifier’.] is to complete blocks 1–18 (except the notification number in block 3) at the time of notification. In some third countries which are not OECD member countries, the competent authority of dispatch may complete these blocks. When the notifier is not the same person as the original producer, this producer or one of the persons indicated in point 15(a)(ii) or (iii) of Article 2 is, where practicable, also to sign in block 17 as specified in the second subparagraph, point 1 of Article 4, and Annex II, Part 1, point 26.

14.

Blocks 1 (See Annex II, Part 1, points 2 and 4) and 2 (Annex II, Part 1, point 6): Provide the required information (give registration number only where applicable, address including the name of the country and telephone and fax numbers including the country code; contact person should be responsible for the shipment including if incidents during shipment occur). In some third countries, information relating to the competent authority of dispatch may be given instead. The notifier may be a dealer or broker in accordance with point 15 of Article 2 of this Regulation. In this case, provide a copy of the contract or evidence of the contract (or a declaration certifying its existence) between the producer, new producer or collector and the broker or dealer in an annex (see Annex II, Part 1, point 23). The phone and fax numbers and the e-mail address should facilitate contact of all relevant persons at any time regarding an incident during shipment.

15.

Normally, the consignee would be the disposal or recovery facility given in block 10. In some cases, however, the consignee may be another person, for example a dealer, a broker [In some third countries which are OECD member countries, the term recognised trader may be used according to the OECD Decision.], or a corporate body, such as the headquarters or mailing address of the receiving disposal or recovery facility in block 10. In order to act as a consignee, a dealer, broker or corporate body must be under the jurisdiction of the country of destination and possess or have some other form of legal control over the waste at the moment the shipment arrives in the country of destination. In such cases, information relating to the dealer, broker or corporate body should be completed in block 2.

16.

Block 3 (See Annex II, Part 1, points 1, 5, 11 and 19): When issuing a notification document, a competent authority will, according to its own system, provide an identification number which will be printed in this block (see paragraph 3 above). Under A, ‘individual shipment’ refers to a single notification and ‘multiple shipments’ to a general notification. Under B, give the type of operation the waste being shipped is destined for. Under C, pre-consent refers to Article 14 of this Regulation.

17.

Blocks 4 (See Annex II, Part 1, point 1), 5 (See Annex II, Part 1, point 17) and 6 (See Annex II, Part 1, point 12): Give the number of shipments in block 4 and the intended date of a single shipment or, for multiple shipments, the dates of the first and last shipments, in block 6. In block 5, give the estimated minimum and maximum weight in tonnes (1 tonne equals 1 megagram (Mg) or 1000 kg) of the waste. In some third countries, giving the volume in cubic metres (1 cubic metre equals 1000 litres) or other metric units, such as kilograms or litres, may also be acceptable. When other metric units are used, the unit of measure may be indicated and the unit in the document may be crossed out. The total quantity shipped must not exceed the maximum quantity declared in block 5. The intended period of time for shipments in block 6 may not exceed one year, with the exception of multiple shipments to pre-consented recovery facilities according to Article 14 of this Regulation (see paragraph 16), for which the intended period of time may not exceed three years. All shipments must take place within the validity period of the written or tacit consents of all competent authorities concerned issued by the competent authorities according to Article 9(6) of this Regulation. In the case of multiple shipments, some third countries may, based on the Basel Convention, require the expected dates or the expected frequency and the estimated quantity of each shipment to be quoted in blocks 5 and 6 or attached in an annex. Where a competent authority issues a written consent to the shipment and the validity period of that consent in block 20 differs from the period indicated in block 6, the decision of the competent authority overrides the information in block 6.

18.

Block 7 (See Annex II, Part 1, point 18): Types of packaging should be indicated using the codes provided in the list of abbreviations and codes attached to the notification document. If special handling precautions are required, such as those required by producers’ handling instructions for employees, health and safety information, including information on dealing with spillage, and instructions in writing for the transport of dangerous goods, tick the appropriate box and attach the information in an annex.

19.

Block 8 (See Annex II, Part 1, points 7 and 13): Provide the required information (give registration number only where applicable, address including the name of the country and telephone and fax numbers including the country code; contact person should be responsible for the shipment). If more than one carrier is involved, append to the notification document a complete list giving the required information for each carrier. Where the transport is organised by a forwarding agent, the agent’s details and the respective information on actual carriers should be provided in an annex. Provide evidence of registration of the carrier(s) regarding waste transports (e.g. a declaration certifying its existence) in an annex (see Annex II, Part 1, point 15). Means of transport should be indicated using the abbreviations provided in the list of abbreviations and codes attached to the notification document.

20.

Block 9 (See Annex II, Part 1, points 3 and 16): Provide the required information on the producer of the waste [Outside the European Community, the term ‘generator’ may be used instead of ‘producer’.]. The registration number of the producer should be given where applicable. If the notifier is the producer of the waste then write ‘Same as block 1’. If the waste has been produced by more than one producer, write ‘See attached list’ and append a list providing the requested information for each producer. Where the producer is not known, give the name of the person in possession or control of such waste (holder). Also provide information on the process by which the waste was produced and the site of production.

21.

Block 10 (See Annex II, Part 1, point 5): Provide the required information (give destination of the shipment by ticking either disposal or recovery facility, registration number only where applicable and actual site of disposal or recovery if it is different from the address of the facility). If the disposer or recoverer is also the consignee, state here ‘Same as block 2’. If the disposal or recovery operation is a D13–D15 or R12 or R13 operation (according to Annexes IIA or IIB of Directive 2006/12/EC on waste), the facility performing the operation should be mentioned in block 10, as well as the location where the operation will be performed. In such a case, corresponding information on the subsequent facility or facilities, where any subsequent R12/R13 or D13–D15 operation and the D1–D12 or R1–R11 operation or operations takes or take place or may take place should be provided in an annex. If the recovery or disposal facility is listed in Annex I, Category 5 of Directive 96/61/EC of 24 September 1996 on integrated pollution and prevention control, evidence (e.g. a declaration certifying its existence) of a valid permit issued in accordance with Articles 4 and 5 of that Directive must be provided in an annex in case a facility is located in the European Community.

22.

Block 11 (See Annex II, Part 1, points 5, 19 and 20): Indicate the type of recovery or disposal operation by using R-codes or D-codes of Annexes IIA or IIB of Directive 2006/12/EC on waste (see also the list of abbreviations and codes attached to the notification document) [In the European Community, the definition of operation R1 in the list of abbreviations is different from that used in the Basel Convention and the OECD Decision; both wordings are therefore provided. There are other differences between the terminology used in the European Community and that used in the Basel Convention and the OECD Decision, which are not contained in the list of abbreviations.]. If the disposal or recovery operation is a D13–D15 or R12 or R13 operation, corresponding information on the subsequent operations (any R12/R13 or D13–D15 as well as D1–D12 or R1–R11) should be provided in an annex. Also indicate the technology to be employed. If the waste is destined for recovery, provide the planned method of disposal for the non-recoverable fraction after recovery, the amount of recovered material in relation to non-recoverable waste, the estimated value of the recovered material and the cost of recovery and the cost of disposal of the non-recoverable fraction in an annex. In addition, in cases of imports into the Community of wastes destined for disposal, indicate a prior duly motivated request from the country of dispatch according Article 41(4) of this Regulation under ‘reason for export’ and attach this request in an annex. Some third countries outside the OECD may, based on the Basel Convention, also require that the reason for export is specified.

23.

Block 12 (See Annex II, Part 1, point 16): Give the name or names by which the material is commonly known or the commercial name and the names of its major constituents (in terms of quantity and/or hazard) and their relative concentrations (expressed as a percentage), if known. In the case of a mixture of wastes, provide the same information for the different fractions and indicate which fractions are destined for recovery. A chemical analysis of the composition of the waste may be requested in accordance with Annex II Part 3 point 7 of this Regulation. Attach further information in an annex if necessary.

24.

Block 13 (See Annex II, Part 1, point 16). Indicate physical characteristics of the waste at normal temperatures and pressures.

25.

Block 14 (See Annex II, Part 1, point 16): State the code that identifies the waste according to Annexes III, IIIA, IIIB, IV or IVA of this Regulation. Give the code according to the system adopted under the Basel Convention (under subheading (i) in block 14) and, where applicable, the systems adopted in the OECD Decision (under subheading (ii)) and other accepted classification systems (under subheadings (iii) to (xii)). According to the second subparagraph, point 6 of Article 4 of this Regulation, give only one waste code (from Annexes III, IIIA, IIIB, IV or IVA of this Regulation) with the following two exceptions: In the case of wastes not classified under one single entry in either Annex III, IIIB, IV or IVA, give only one type of waste. In the case of mixtures of wastes not classified under one single entry in either Annex III, IIIB, IV or IVA, unless listed in Annex IIIA, provide the code of each fraction of the waste in order of importance (in an annex if necessary).

(a)

Subheading (i): Basel Convention Annex VIII codes should be used for wastes that are subject to the procedure of prior written notification and consent (see Part I of Annex IV of this Regulation); Basel Annex IX codes should be used for wastes that are not usually subject to the procedure of prior written notification and consent but which, for a specific reason such as contamination by hazardous substances (cf. paragraph 1 of Annex III of this Regulation) or different classification according to Article 63 of this Regulation or national regulations [Commission Regulation (EC) No 1418/2007 of 29 November 2007 concerning the export for recovery of certain waste listed in Annex III or IIIA to Regulation (EC) No 1013/2006 to certain countries to which the OECD Decision on the control of transboundary movements of wastes does not apply, OJ L 316, 4.12.2007, p. 6.], are subject to the procedure of prior written notification and consent (see Part I of Annex III of this Regulation). Basel Annexes VIII and IX can be found in Annex V of this Regulation, in the text of the Basel Convention as well as in the Instruction Manual available from the Secretariat of the Basel Convention. If a waste is not listed in Annexes VIII or IX of the Basel Convention, insert ‘not listed’.

(b)

Subheading (ii): OECD member countries should use OECD codes for wastes listed in Part II of Annexes III and IV of this Regulation, i.e. wastes that have no equivalent listing in the Annexes of the Basel Convention or that have a different level of control under this Regulation from the one required by the Basel Convention. If a waste is not listed in Part II of Annexes III and IV of this Regulation, insert ‘not listed’.

(c)

Subheading (iii): European Union Member States should use the codes included in the European Community list of wastes (see Commission Decision 2000/532/EC as amended) [See http://europa.eu.int/eur-lex/en/consleg/main/2000/en_2000D0532_index.html]. Such codes may also be included in Annex IIIB of this Regulation.

(d)

Subheadings (iv) and (v): Where applicable, national identification codes other than the EC list of wastes used in the country of dispatch and, if known, in the country of destination should be used. Such codes may be included in Annexes IIIA, IIIB or IVA of this Regulation.

(e)

Subheading (vi): If useful or required by the relevant competent authorities, add here any other code or additional information that would facilitate the identification of the waste.

Such codes may be included in Annexes IIIA, IIIB, IV (EU48) or IVA of this Regulation. In that case, the Annex number should be stated in front of the codes. As regards Annex IIIA, the relevant code(s) as indicated in Annex IIIA should be used, as appropriate in sequence. Certain Basel entries such as B1100 and B3020 are restricted to particular waste streams only, as indicated in Annex IIIA.

(f)

Subheading (vii): State the appropriate Y-code or Y-codes according to the ‘Categories of wastes to be controlled’ (see Annex I of the Basel Convention and Appendix 1 of the OECD Decision), or according to the ‘Categories of wastes requiring special consideration’ given in Annex II of the Basel Convention (see Annex IV Part I of this Regulation or Appendix 2 of the Basel Instruction Manual), if it or they exist(s). Y-codes are not required by this Regulation and the OECD Decision except where the waste shipment falls under one of the two ‘Categories requiring special consideration’ under the Basel Convention (Y46 and Y47 or Annex II wastes), in which case the Basel Y-code should be indicated. Nevertheless, indicate the Y-code or Y-codes for wastes defined as hazardous according Article 1(1)(a) of the Basel Convention in order to fulfil the reporting requirements under the Basel Convention.

(g)

This article is long: the rest is at the official publication.