HEAD PERFORMANCE CRITERION (HPC)
1.1. This criterion is considered to be satisfied when, during the test, there is no contact between the head and any vehicle component.
If that is not the case, a calculation of the value of HPC is made, on the basis of the acceleration (a), measured according to paragraph 5.2.1 of Annex 3, by the following expression:
Text of image
HPC = (t 2 – t 1 ) [1 t 2 – t 1 t 2 ∫t 1 adt] 2.5
in which:
1.2.1. the term ‘a’ is the resultant acceleration measured according to paragraph 5.2.1. of Annex 3 and is measured in units of gravity, g (1 g = 9,81 m/s 2 );
1.2.2. if the beginning of the head contact can be determined satisfactorily, t 1 and t 2 are the two time instants, expressed in seconds, defining an interval between the beginning of the head contact and the end of the recording for which the value of HPC is maximum;
1.2.3. if the beginning of the head contact cannot be determined, t 1 and t 2 are the two time instants, expressed in seconds, defining a time interval between the beginning and the end of the recording for which the value of HPC is maximum;
1.2.4. Values of HPC for which the time interval (t 1 - t 2 ) is greater than 36 ms are ignored for the purposes of calculating the maximum value.
1.3. The value of the resultant head acceleration during forward impact which is exceeded for 3 ms cumulatively is calculated from the resultant head acceleration measured according to paragraph 5.2.1 of Annex 3.
NECK INJURY CRITERIA (NIC)
2.1. These criteria are determined by the compressive axial force, the axial tensile force and the fore/aft shear forces at the head/neck interface, expressed in kN and measured according to paragraph 5.2.2 of Annex 3 and by the duration of these forces expressed in ms.
2.2. The neck bending moment criterion is determined by the bending moment, expressed in Nm, about a lateral axis at the head/neck interface and measured according to paragraph 5.2.2 of Annex 3.
2.3. The neck flexion bending moment, expressed in Nm, shall be recorded.
THORAX COMPRESSION CRITERION (ThCC) AND VISCOUS CRITERION (V * C)
3.1. The thorax compression criterion is determined by the absolute value of the thorax deformation, expressed in mm and measured according to paragraph 5.2.3 of Annex 3.
3.2. The viscous criterion (V * C) is calculated as the instantaneous product of the compression and the rate of deflection of the sternum, measured according to paragraph 6 and also paragraph 5.2.3 of Annex 3.
FEMUR FORCE CRITERION (FFC)
4.1. This criterion is determined by the compression load expressed in kN, transmitted axially on each femur of the dummy and measured according to paragraph 5.2.4 of Annex 3 and by the duration of the compressive load expressed in ms.
TIBIA COMPRESSIVE FORCE CRITERION (TCFC) AND TIBIA INDEX (TI)
5.1. The tibia compressive force criterion is determined by the compressive load (F z ) expressed in kN, transmitted axially on each tibia of the dummy and measured according to paragraph 5.2.4 of Annex 3.
5.2. The tibia index is calculated on the basis of the bending moments (Mx and My) measured according to paragraph 5.1 by the following expression:
where:
Mx | = | bending moment about the x axis
My | = | bending moment about the y axis
(Mc)R | = | critical bending moment and shall be taken to be 225 Nm
Fz | = | compressive axial force in the z direction
(Fc)z | = | critical compressive force in the z direction and shall be taken to be 35,9 kN and
MR | = | .
The tibia index is calculated for the top and the bottom of each tibia; however, F z may be measured at either location. The value obtained is used for the top and bottom TI calculations. Moments Mx and My are both measured separately at both locations.
PROCEDURE FOR CALCULATING THE VISCOUS CRITERIA (V * C) FOR HYBRID III DUMMY
6.1. The viscous criterion is calculated as the instantaneous product of the compression and the rate of deflection of the sternum. Both are derived from the measurement of sternum deflection.
6.2. The sternum deflection response is filtered once at CFC 180. The compression at time t is calculated from this filtered signal as:
Text of image
C (t) = D (t) 0.229
The sternum deflection velocity at time t is calculated from the filtered deflection as:
Text of image
V (t) = 8 (D (t+1) - D (t-1) ) - (D (t+2) - D (t-2) ) 12∂t
where D( t ) is the deflection at time t in metres and ∂t is the time interval in seconds between the measurements of deflection. The maximum value of ∂t shall be 1,25 x 10 -4 seconds. This calculation procedure is shown diagrammatically below:
Measured Deflection D (t)
Filter at CFC 180
Calculate deflection velocity V (t)
Calculate compression C (t)
Calculate viscous criterion at time t
(V*C) (t) = 1,3 x (V (t) x C (t) )
Determine the maximum value of
(V*C) (MAX) = max [(V*C) (t) ]