16 Regulation No 95 Uniform provisions concerning the approval of vehicles with regard to the protection of the occupants in the event of a lateral collision, Decision_act (EU) 2005/614

In force

CONTENTS

Regulation

1.

Scope

2.

Definitions

3.

Application for approval

4.

Approval

5.

Specifications and tests

6.

Modification of the vehicle type

7.

Conformity of production

8.

Penalties for non-conformity of production

9.

Production definitely discontinued

10.

Transitional provisions

11.

Names and addresses of technical services responsible for conducting approval tests, and of administrative departments

Annexes

Annex 1 | Communication concerning the approval or extension or refusal or withdrawal of approval or production definitely discontinued of a vehicle type with regard to protection of occupants in the event of a lateral collision, pursuant to Regulation No 95

Annex 2 | Arrangements of the approval mark

Annex 3 | Procedure for determining the ‘H’ point and the actual torso angle for seating positions in motor vehicles

Appendix 1 | Description of the three-dimensional ‘H’ point machine (3-D H machine)

Appendix 2 | Three-dimensional reference system

Appendix 3 | Reference data concerning seating positions

Annex 4 | Collision test procedure

Appendix 1 | Determination of performance data

Appendix 2 | The procedure for calculating the viscous criterion for Eurosid 1

Annex 5 | Mobile deformable barrier characteristics

Appendix | Examination of the mobile deformable barrier

Annex 6 | Technical description of the side impact dummy

Annex 7 | Installation of the side impact dummy

Annex 8 | Partial test

1.

SCOPE

This Regulation applies to the lateral collision behaviour of the structure of the passenger compartment of M 1 and N 1 categories of vehicles where the ‘R’ point of the lowest seat is not more than 700 mm from ground level when the vehicle is in the condition corresponding to the reference mass defined in paragraph 2.10 of this Regulation.

2.

DEFINITIONS

For the purposes of this Regulation:

2.1. ‘approval of a vehicle’ means the approval of a vehicle type with regard to the behaviour of the structure of the passenger compartment in a lateral collision;

‘vehicle type’ means a category of power-riven vehicles which do not differ in such essential respects as:

2.2.1. the length, width and ground clearance of the vehicle, in so far as they have a negative effect on the performance prescribed in this Regulation;

2.2.2. the structure, dimensions, lines and materials of the side walls of the passenger compartment in so far as they have a negative effect on the performance prescribed in this Regulation;

2.2.3. the lines and inside dimensions of the passenger compartment and the type of protective systems, in so far as they have a negative effect on the performance prescribed in this Regulation;

2.2.4. the siting of the engine (front, rear or centre);

2.2.5. the unladen mass, in so far as there is a negative effect on the performance prescribed in this Regulation;

2.2.6. the optional arrangements or interior fittings in so far as they have a negative effect on the performance prescribed in this Regulation;

2.2.7. the type of front seat(s) and position of the ‘R’ point in so far as they have a negative effect on the performance prescribed in this Regulation;

2.3. ‘passenger compartment’ means the space for occupant accommodation, bounded by the roof, floor, side walls, doors, outside glazing and front bulkhead and the plane of the rear compartment bulkhead or the plane of the rear-eat back support;

‘R point’ or ‘seating reference point’ means the reference point specified by the vehicle manufacturer which:

2.4.1. has coordinates determined in relation to the vehicle structure;

2.4.2. corresponds to the theoretical position of the point of torso/thighs rotation (‘H’ point) for the lowest and most rearward normal driving position or position of use given by the vehicle manufacturer for each seating position specified by him;

2.5. H point’ is as established by Annex 3 to this Regulation;

2.6. ‘capacity of the fuel tank’ means the fuel tank capacity as specified by the manufacturer of the vehicle;

2.7. ‘transverse plane’ means a vertical plane perpendicular to the median longitudinal vertical plane of the vehicle;

2.8. ‘protective system’ means devices intended to restrain and/or protect the occupants;

2.9. ‘type of protective system’ means a category of protective devices which do not differ in such essential respects as their:

–

technology,

–

geometry,

–

constituent materials;

2.10. ‘reference mass’ means the unladen mass of the vehicle increased by a mass of 100 kg (that is the mass of the side impact dummy and its instrumentation);

2.11. ‘unladen mass’ means the mass of the vehicle in running order without driver, passengers or load, but with the fuel tank filled to 90 % of its capacity and the usual set of tools and spare wheel on board, where applicable;

2.12. ‘mobile deformable barrier’ means the apparatus with which the test vehicle is impacted. It consists of a trolley and an impactor;

2.13. ‘impactor’ means a crushable section mounted on the front of mobile deformable barrier;

2.14. ‘trolley’ means a wheeled frame free to travel along its longitudinal axis at the point of impact. Its front supports the impactor.

3.

APPLICATION FOR APPROVAL

3.1. The application for approval of a vehicle type with regard to the protection of the occupants in the event of a lateral collision shall be submitted by the vehicle manufacturer or by his duly accredited representative.

It shall be accompanied by the undermentioned documents in triplicate and the following particulars:

3.2.1. a detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent materials;

3.2.2. photographs and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the lateral part of the structure;

3.2.3. particulars of the vehicle’s mass as defined by paragraph 2.11 of this Regulation;

3.2.4. the lines and inside dimensions of the passenger compartment;

3.2.5. a description of the relevant side interior fittings and protective systems installed in the vehicle.

3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved on prototype vehicles with a sufficient degree of accuracy.

A vehicle which is representative of the type to be approved shall be submitted to the technical service responsible for conducting the approval tests.

3.4.1. A vehicle not comprising all the components proper to the type may be accepted for tests provided that it can be shown that the absence of the components omitted has no detrimental effect on the performance prescribed in the requirements of this Regulation.

3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1 is in compliance with the requirements of this Regulation.

4.

APPROVAL

4.1. If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraph 5, approval of that vehicle type shall be granted.

4.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the technical service.

4.3. An approval number shall be assigned to each type approved. Its first two digits (at present 01 corresponding to the 01 series of amendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party may not assign the same approval number to another vehicle type.

4.4. Notice of approval or of extension or of refusal of approval of a vehicle type pursuant to this Regulation shall be communicated by the Parties to the Agreement applying this Regulation by means of a form conforming to the model in Annex 1 to this Regulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297 mm) or folded to that format and on an appropriate scale.

There shall be affixed to every vehicle conforming to a vehicle type approved under this Regulation, conspicuously and in a readily accessible place specified on the approval form, an international approval mark consisting of:

4.5.1. a circle surrounding the letter ‘E’ followed by the distinguishing number of the country which has granted approval ( 13 ) ;

4.5.2. the number of this Regulation, followed by the letter ‘R’, a dash and the approval number, to the right of the circle prescribed in paragraph 4.5.1.

4.6. If the vehicle conforms to a vehicle type approved, under one or more other Regulations Annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 4.5.1 need not be repeated; in this case the Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 4.5.1.

4.7. The approval mark shall be clearly legible and shall be indelible.

4.8. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer.

4.9. Annex 2 to this Regulation gives examples of approval marks.

5.

SPECIFICATIONS AND TESTS

The vehicle shall undergo a test in accordance with Annex 4 to this Regulation.

The test will be carried out on the driver’s side unless asymmetric side structures, if any, are so different as to affect the performance in a side impact. In that case either of the alternatives in paragraph 5.1.1.1 or 5.1.1.2 may be used by agreement between the manufacturer and test authority.

5.1.1.1. The manufacturer will provide the authority responsible for approval with information regarding the compatibility of performances in comparison with the driver’s side when the test is being carried out on that side.

5.1.1.2. The approval authority, if concerned as to the construction of the vehicle, will decide to have the test performed on the side opposite the driver, this being considered the least favourable.

5.1.2. The Technical Service, after consultation with the manufacturer, may require the test to be carried out with the seat in a position other than the one indicated in paragraph 5.5.1 of Annex 4. This position shall be indicated in the test report ( 14 ) .

5.1.3. The result of this test shall be considered satisfactory if the conditions set out in paragraphs 5.2 and 5.3 are satisfied.

Performance criteria

The performance criteria, as determined for the collision test in accordance with the Appendix to Annex 4 to this Regulation shall meet the following conditions:

5.2.1.1. the head performance criterion (HPC) shall be less than or equal to 1 000; when there is no head contact, then the HPC shall not be measured or calculated but recorded as ‘no head contact’;

5.2.1.2. the thorax performance criteria shall be:

(a)

rib deflection criterion (RDC) less than or equal to 42 mm;

(b)

soft tissue criterion (VC) less or equal to 1,0 m/sec.

For a transitional period of two years after the date specified in paragraph 10.2 of this Regulation the V * C value is not a pass/fail criterion for the approval testing, but this value has to be recorded in the test report and to be collected by the approval authorities. After this transitional period, the VC value of 1,0 m/sec shall apply as a pass/fail criterion unless the Contracting Parties applying this Regulation decide otherwise;

5.2.1.3. the pelvis performance criterion shall be:

pubic symphysis peak force (PSPF) less than or equal to 6 kN;

5.2.1.4. the abdomen performance criterion shall be:

abdominal peak force (APF) less than or equal to 2,5 kN internal force (equivalent to external force of 4,5 kN).

Particular requirements

5.3.1. No door shall open during the test.

After the impact, it shall be possible without the use of tools to:

5.3.2.1. open a sufficient number of doors provided for normal entry and exit of passengers, and if necessary tilt the seat-backs or seats to allow evacuation of all occupants;

5.3.2.2. release the dummy from the protective system;

5.3.2.3. remove the dummy from the vehicle;

5.3.3. no interior device or component shall become detached in such a way as noticeably to increase the risk of injury from sharp projections or jagged edges;

5.3.4. ruptures, resulting from permanent deformation are acceptable, provided these do not increase the risk of injury;

5.3.5. if there is continuous leakage of liquid from the fuel-feed installation after the collision, the rate of leakage shall not exceed 30 g/min; if the liquid from the fuel-feed system mixes with liquids from the other systems and the various liquids cannot easily be separated and identified, all the liquids collected shall be taken into account in evaluating the continuous leakage.

6.

MODIFICATION OF THE VEHICLE TYPE

Any modification affecting the structure, the number and type of seats, the interior trim or fittings, or the position of the vehicle controls or of mechanical parts which might affect the energy-absorption capacity of the side of the vehicle, shall be brought to the notice of the administrative department granting approval. The department may then either:

6.1.1. consider that the modifications made are unlikely to have an appreciable adverse effect and that in any case the vehicle still complies with the requirements, or

require a further test report from the technical service responsible for conducting the tests.

6.1.2.1. Any modification of the vehicle affecting the general form of the structure of the vehicle or any variation in the reference mass greater than 8 % which in the judgement of the authority would have a marked influence on the results of the test shall require a repetition of the test as described in Annex 4.

6.1.2.2. If the technical service, after consultation with the vehicle manufacturer, considers that modifications to a vehicle type are insufficient to warrant a complete retest then a partial test may be used. This would be the case if the reference mass is not more than 8 % different from the original vehicle or the number of front seats is unchanged. Variations of seat type or interior fittings need not automatically entail a full retest. An example of the approach to this problem is given in Annex 8.

6.2. Confirmation or refusal of approval, specifying the alteration, shall be communicated by the procedure specified in paragraph 4.4 to the Parties to the Agreement which apply this Regulation.

6.3. The competent authority issuing an extension of approval shall assign a series number to each communication form drawn up for such an extension.

7.

CONFORMITY OF PRODUCTION

The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2), with the following requirements:

7.1. Every vehicle approved under this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set out in paragraph 5.

7.2. The holder of the approval shall ensure that for each type of vehicle at least the tests concerning the taking of measurements are carried out.

7.3. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years.

8.

PENALTIES FOR NON-CONFORMITY OF PRODUCTION

8.1. The approval granted in respect of a vehicle type, pursuant to this Regulation, may be withdrawn if the requirement laid down in paragraph 7.1. above is not complied with, or if the vehicle or vehicles selected have failed to pass the checks prescribed in paragraph 7.2.

8.2. If a Contracting Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith so notify the other Contracting Parties applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.

9.

PRODUCTION DEFINITELY DISCONTINUED

If the holder of the approval completely ceases to manufacture a type of vehicle approved in accordance with this Regulation, he shall so inform the authority which granted the approval. Upon receiving the relevant communication that authority shall inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.

10.

TRANSITIONAL PROVISIONS

10.1. As from the official date of entry into force of the 02 series of amendments, no Contracting Party applying this Regulation shall refuse to grant ECE approval under this Regulation as amended by the 02 series of amendments.

10.2. As from 12 months after the entry into force of the 02 series of amendments Contracting Parties applying this Regulation shall grant ECE approvals only to those types of vehicles which comply with the requirements of this Regulation as amended by the 02 series of amendments.

10.3. As from 60 months after the entry into service of the 02 series of amendments Contracting Parties applying this Regulation may refuse first national registration (first entry into service) of vehicles which do not meet the requirements of this Regulation as amended by the 02 series of amendments.

11.

NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF ADMINISTRATIVE DEPARTMENTS

The Contracting Parties to the Agreement applying this Regulation shall communicate to the United Nations secretariat the names and addresses of the technical services responsible for conducting approval tests, and of the administrative departments which grant approval and to which forms certifying approval or extension, or refusal or withdrawal of approval, issued in other countries, are to be sent.