The purpose of this test is to verify that the steering control meets the requirements set out in item 5.3 of Annex I.
INSTALLATIONS, PROCEDURES AND MEASURING INSTRUMENTS
2.1. General
2.1.1. The steering control shall be tested complete with trim.
2.1.2. If the steering control is fitted with an air bag the test shall be carried out with the air bag inflated. At the request of the manufacturer, and with the agreement of the technical service, the test may be carried out without the air bag inflated.
2.2. Mounting of the steering control when seeking steering control approval related to vehicle approval
2.2.1. The control shall be mounted on the front section of the vehicle obtained by cutting the body transversely at the level of the front seats, and possibly eliminating the roof, windscreen and doors.
This section shall be fixed rigidly to the test bench, so that it does not move under the impact of the head form.
The tolerance on the control mounting angle shall be ± 2 degrees of the design angle.
2.2.2. However, at the request of the manufacturer and with the agreement of the technical service, the steering control may be mounted on a framework simulating the mounting of the steering mechanism provided that, as compared with the real front body section/steering mechanism assembly, the framework/steering mechanism assembly has:
2.2.2.1. the same geometric layout, and
2.2.2.2. greater rigidity.
2.2.2.1. the same geometric layout, and
2.2.2.2. greater rigidity.
2.3. Mounting the steering control when seeking steering control approval only
The steering control shall be tested complete with trim. The steering control must have a minimum collapsing space of 100 mm between the steering control and the test bench. The steering shaft shall be firmly attached to the test bench so that the steering shaft does not move under impact (See Figure 2).
2.3.1. However, at the request of the manufacturer the test may be carried out under the conditions specified in paragraph 2.2 above. In this case the approval is only valid for mounting on a specified vehicle type(s).
TEST APPARATUS
3.1. This apparatus consists of a fully-guided linear impactor with a mass of 6,8 kg.
3.2. The head-form shall be fitted with two accelerometers and a speed-measuring device, all capable of measuring values in the impact direction.
3.3. Measuring instruments
3.3.1. The measuring instruments used shall comply with ISO 6487-1987. In addition they shall have the following characteristics:
3.3.2. Acceleration
Channel amplitude class 150 g
Channel frequency class (600) Hz;
3.3.3. Speed
Accurate to within ± 1 %;
3.3.4. Time recording
The instrumentation shall enable the action to be recorded throughout its duration and the readings to be made accurate to one thousandth of a second. The beginning of the impact at the moment of first contact between the impactor and the steering control shall be noted on the recordings used for analysing the test.
3.3.1. The measuring instruments used shall comply with ISO 6487-1987. In addition they shall have the following characteristics:
3.3.2. Acceleration
Channel amplitude class 150 g
Channel frequency class (600) Hz;
3.3.3. Speed
Accurate to within ± 1 %;
3.3.4. Time recording
The instrumentation shall enable the action to be recorded throughout its duration and the readings to be made accurate to one thousandth of a second. The beginning of the impact at the moment of first contact between the impactor and the steering control shall be noted on the recordings used for analysing the test.
TEST PROCEDURE
4.1. The plane of the steering control shall be set up perpendicular to the direction of impact.
4.2. A maximum of four and a minimum of three positions on each steering control type shall be impacted. A new steering control shall be used for each impact. On successive impacts the axial axis of the impactor shall be in line with one of the following points:
4.2.1. the centre of the steering control boss;
4.2.2. the joint of the stiffest or most supported spoke to the inner edge of the steering control rim;
4.2.3. the mid-point of the shortest unsupported arc of the steering control rim that does not include a spoke;
4.2.4. at the discretion of the approval authority, the ‘worst case’ position on the steering control.
4.2.1. the centre of the steering control boss;
4.2.2. the joint of the stiffest or most supported spoke to the inner edge of the steering control rim;
4.2.3. the mid-point of the shortest unsupported arc of the steering control rim that does not include a spoke;
4.2.4. at the discretion of the approval authority, the ‘worst case’ position on the steering control.
4.3. The impactor shall strike the steering control at a velocity of 24,1 km/h; this velocity shall be achieved either by the mere energy of propulsion or by using an additional propelling device.
RESULTS
5.1. In the tests carried out according to the above procedures, the deceleration rate of the impactor shall be taken as the simultaneous average of the readings of the two decelerometers.
EQUIVALENT PROCEDURES
6.1. Alternative tests may be permitted at the discretion of the approval authority provided equivalence can be demonstrated. A report shall be attached to the approval documentation describing the method used and the results obtained.
6.2. Responsibility for demonstrating the equivalence of the alternative method shall rest with the manufacturer or his representative wishing to use such a method.
PRESCRIPTIONS OF RIGIDITY BETWEEN STEERING SHAFT AND TEST BENCH
(See Figures 1 and 2)
(Figure 1)
(Figure 2)
Under a load of 800 dN, producing a couple of 160 m.dN in relation to the point B, the displacement in any direction of the point A shall be lower than 2 mm.