3 Appendix 1 OBM parameters to support vehicle testing, Regulation (EU) 2025/1707

In forcesince 25 Jul 2025

Reference | Name | Description | Required for Instantaneous data stream

General Parameters

1.1 | Number of diagnostic trouble codes (DTCs) | Number of stored ‘MI on’ fault codes | -

1.2 | MI status | Malfunction Indicator status | Yes

1.3 | Engine coolant temperature | Engine coolant temperature derived from engine coolant temperature, cylinder head temperature or another applicable sensor | Yes

1.4 | Engine speed | Revolutions per minute of engine crankshaft | Yes

1.5 | Calculated load value |

Percent of maximum available engine torque.

Calculated load value shall be calculated based on current engine torque / peak engine torque @STP as a function of engine speed

Yes

1.6 | Vehicle speed | Vehicle road speed | Yes

1.7 | Ambient air temperature |

Ambient air temperature.

If the parameter provided is normally estimated or modelled from other sensors or signals, the value used for calculation of OBM trip data signals shall be provided

Yes

1.8 | Ambient air pressure |

Ambient / barometric pressure.

If the parameter provided is normally estimated or modelled from other sensors or signals the value used for calculation of OBM trip data signals shall be provided

Yes

1.9 | Vehicle / engine fuel rate | Fuel injected into engine / aftertreatment | Yes

1.10 | AES flag / timer | Status information to indicate AES is active | -

1.11 | Exhaust mass flow -tailpipe | Exhaust mass flow rate at the tailpipe as defined in paragraph 1.3 | Yes

Exhaust emissions parameters

1.12 | NOx sensor concentration(s) |

NOx sensor signal(s) derived from physical sensors installed on the vehicle

Manufacturers may provide either raw and /or compensated signals as deemed most appropriate to support testing and repair

Yes

1.13 | Tailpipe NOx concentration | Estimated / measured total concentration of NOx emissions at the tailpipe as defined in paragraph 1.4 | Yes

1.14 | Tailpipe NOx concentration modelled status | Modelled status of ‘Tailpipe NOx concentration’ signal, as defined in paragraph 1.5 | Yes

1.15 | Tailpipe NOx mass flow | Estimated / measured total mass of NOx emissions at the tailpipe as defined in paragraph 1.6 | Yes

1.16 | Tailpipe NOx mass flow modelled status | Modelled status of ‘Tailpipe NOx mass flow’ signal, as defined in paragraph 1.5 | Yes

1.17 | PM sensor output | Particle mass sensor(s) output value(s) applicable to sensor type installed on the vehicle | Yes

1.18 | Status of PM sensor | Status of PM sensor operation | Yes

NOx to fuel mass parameters |

1.19 | Cumulative NOx – 100 km | Total emitted NOx mass (g) during the current NOx to fuel mass 100 km driven period, as defined in paragraph 1.7 | -

1.20 | Cumulative fuel mass – 100 km | Total fuel burned (kg) during the current NOx to fuel mass 100 km driven period, as defined in paragraph 1.7 | -

1.21 | Cumulative distance – 100 km | Total driven distance (km) during current NOx to fuel mass 100 km driven period, as defined in paragraph 1.7 | -

1.22 | NOx to fuel mass ratio (0) | Calculated ratio of NOx emissions to fuel consumed over 100 km (0), as defined in paragraph 1.7 | -

1.23 | NOx to fuel mass ratio (1) | Calculated ratio of NOx emissions to fuel consumed over 100 km (1), as defined in paragraph 1.7 | -

1.24 | NOx to fuel mass ratio (2) | Calculated ratio of NOx emissions to fuel consumed over 100 km (2), as defined in paragraph 1.7 | -

1.25 | NOx to fuel mass ratio (3) | Calculated ratio of NOx emissions to fuel consumed over 100 km (3), as defined in paragraph 1.7 | -

1.26 | NOx to fuel mass ratio (4) | Calculated ratio of NOx emissions to fuel consumed over 100 km (4), as defined in paragraph 1.7 | -

1.27 | NOx to fuel mass ratio average | Parameter shall represent the average value of the 5 last completed ‘NOx to fuel mass ratio’ (0-4) values, as defined in paragraph 1.7 | -

Aftertreatment regeneration status parameters |

1.28 | Aftertreatment regeneration status | Status of aftertreatment regeneration | Yes

1.29 | Normalised trigger for particulate filter regeneration | Normalised trigger for active particle filter (PF) regeneration functions employed on the vehicle | Yes

1.30 | Particulate filter average regeneration distance | Average distance between particulate filter regenerations | -

NOx control system parameters |

1.31 | Aftertreatment operational status | Aftertreatment operational status, as defined in paragraph 1.8 | Yes

1.32 | SCR inducement state | SCR inducement system actual state | -

1.33 | Average reagent consumption | Average aftertreatment reagent consumption | -

1.34 | Average reagent demand | Average demanded aftertreatment reagent consumption | -

1.35 | Reagent tank level | Reagent tank level | -

1.36 | SCR catalyst NH3 target | Target SCR catalyst NH3 storage | -

1.37 | SCR catalyst NH3 storage | Actual/modelled SCR catalyst NH3 storage | -

Electrical system parameters(1) |

1.38 | Hybrid/EV Battery System voltage | Rechargeable energy storage system voltage | Yes

1.39 | Hybrid/EV Battery System current | Rechargeable energy storage system current | Yes

1.40 | Hybrid/EV battery temperature data | Rechargeable energy storage system temperature data to include as applicable to the application min, max, average and current battery temperature, battery coolant temperatures and current state of battery thermal control | -

1.41 | Low voltage battery voltage | Control module system voltage | Yes

1.42 | Hybrid/EV battery system remaining charge (SOC) | Remaining level of charge for a battery pack used for propulsion, expressed as a percentage of total useable battery energy | Yes

1.43 | Accelerator pedal position | Relative or ‘learned’ pedal position shall be displayed as a normalised value | Yes

1.44 | Hybrid/EV battery system cumulative energy | Cumulative battery system energy consumption for the last second | Yes

OBM system status parameters |

1.45 | OBM inducement system status | Status of the OBM inducement system as defined in paragraph 1.9 | -

1.46 | Possible tampering status | Status of vehicle tampering detection as defined in paragraph 1.10 | -

1.47 | Monitoring status NOx | Monitoring status for NOx according to Article 5 | -

1.48 | Monitoring status PM | Monitoring status for PM according to Article 5 | -

1.49 | Monitoring status generic | Generic monitoring status according to Article 5 | -

EEEDWS Counters |

1.50 | OBM warning distance | Counter to track warning distance as defined in Annex II, paragraph 2.2.4 | -

1.51 | OBM distance since monitoring status reset | Distance driven since all monitoring statuses equal to ‘normal’ or ‘intermediate’, as defined in Annex II, paragraph 2.2.5 | -

1.52 | OBM current inducement distance | Distance travelled in current inducement period, as defined in Annex II, paragraph 2.2.7 | -

1.53 | Distance since DTC reset | Distance accumulated since diagnostic trouble codes were last cleared by a generic scan tool or service tool | -

1.54 | Distance travelled while MI activated | Distance travelled while the MI is activated | -

1.55 | OBM OTA outbox overwrite counter | Number of times the ‘OBM OTA outbox’ is overwritten since last fault clear as defined in paragraph 1.12 | -

(1)

Only applicable to OVC-HEV, PEV and FCV/FCHV