3 ANNEX III EU Ecolabel criteria for awarding the EU Ecolabel to water-based aerosol spray paints, Decision_act (EU) 2025/2607

In forcesince 17 Dec 2025

The EU Ecolabel criteria target the best water-based aerosol spray paints on the market, in terms of environmental performance. The criteria focus on the main environmental impacts associated with the life cycle of these products and promote circular economy aspects.

For the EU Ecolabel to be awarded to a specific product, the product shall comply with each requirement. The applicant shall provide a written confirmation stating that all the criteria are fulfilled.

Specific assessment and verification requirements are indicated within each criterion.

Where the applicant is required to provide declarations, documentation, analyses, test reports, or other evidence to show compliance with the criteria, these may originate from the applicant and/or their supplier(s) as appropriate.

Competent bodies shall preferentially recognise attestations that are issued by bodies accredited in accordance with the relevant harmonised standard for testing and calibration laboratories, and verifications by bodies that are accredited in accordance with the relevant harmonised standard for bodies certifying products, processes, and services.

Where appropriate, test methods other than those indicated for each criterion may be used if the competent body assessing the application accepts their equivalence.

Where appropriate, competent bodies may require supporting documentation and may carry out independent verifications or site inspections to check compliance with these criteria.

Changes in suppliers and production sites pertaining to products to which the EU Ecolabel has been awarded shall be notified to competent bodies, together with supporting information to enable verification of continued compliance with the criteria.

As pre-requisite, the product shall meet all respective legal requirements of the country or countries in which the product is intended to be placed on the market. The applicant shall declare the product’s compliance with this requirement.

The following information shall be provided together with the application for the EU Ecolabel:

(a)

A list of all individual paint and varnish products covered by the EU Ecolabel application, grouped into product families and indicating any relevant product characteristics that affect which specific requirements from the EU Ecolabel criteria would apply. A family of products will all have the same base formulation and product subcategory, but may differ in terms of shade and/or packaging format.

(b)

A description of the product formulation(s), with a % composition of the ingredients used and the specific function of each ingredient (the composition information may be subject to a non-disclosure agreement between the applicant and the competent body or, in some cases, directly between the supplier and the competent body). Ingredient functions shall be either: accelerator; additive; anti-blocking agent; anti-foaming agent; anti-settling agent; anti-skinning agent; binder; coalescing agent; colourant-dyestuff; colourant-pigment; crosslinking agent; curing agent/hardener; diluent; dispersing agent; drier; filler; dry-film preservative; in-can preservative; matting agent; neutralising agent; optical brightener; plasticiser; polymer dispersion; preservative stabiliser; resin; retarder; rheological modifier; silicone resin; solvent; surfactant; UV stabiliser; water; water-repelling agent or, in case none of these apply, ‘other’.

(c)

Safety data sheets for the ingredients used in the paint and varnish formulations.

(d)

Any other information associated with the production of ingredients and materials that is necessary for demonstrating compliance with the EU Ecolabel criteria shall be provided by the suppliers or producers of those ingredients and materials.

(e)

In order to help determine the number of products within any given family of products, a description of the packaging format(s) used, the volume(s) of product held and the packaging material(s) used for each of the paint and varnish products covered by the EU Ecolabel application.

(f)

In order to reduce the quantity of testing and documentation required for assessment and verification procedures, several criteria explicitly state that compliance of an entire family of products can be assumed if the worst-case product can be shown to comply. Each time data for a worst-case product is submitted, it shall be accompanied by an explanation of why this particular product represents the worst-case within its family of products for the property being tested.

If the final product contains more than 3,0 % w/w of titanium dioxide (TiO2) pigment, the emissions to air and water from the production of any titanium dioxide pigment used shall meet the relevant requirements listed below for the respective production processes:

[Point sources for emissions of dust to air from the chloride process are considered as: milling, chlorination, oxidation and micronisation stages. Point sources for emissions of HCl to air from the chloride process are considered as: chlorination, acid scrubber from solid separation and metal chloride treatment processes. Point sources for emissions of dust to air from the sulphate process are considered as: milling, digestion, calcination and micronisation stages. Point sources for emissions of SO2 to air from the sulphate process are considered as: digestion and calcination processes.] [When ore used is > 95 % TiO2 content.] [When ore used is 90-95 % TiO2 content.] [When ore used is < 90 % TiO2 content.]

Parameter and analytical method | Sulphate process | Chloride process

Emissions of dust to air (measured with the relevant European or international standards) | ≤ 0,40 kg/t TiO2 pigment | ≤ 0,66 kg/t TiO2 pigment

Emissions of SO2 to air (measured with the relevant European or international standards) | ≤ 4,5 kg/t TiO2 pigment | n/a

Emissions of HCl to air (measured with the relevant European or international standards) | n/a | ≤ 0,70 kg/t TiO2 pigment

Emissions of SO42- to water (measured with the relevant European or international standards) | ≤ 300 kg SO42-/t TiO2 pigment | n/a

Emissions of Cl- to water (measured using the mass balance method or with the relevant European or international standards) | n/a |

≤ 103 kg Cl-/t TiO2 pigment

≤ 179 kg Cl-/t TiO2 pigment

≤ 329 kg Cl-/t TiO2 pigment

Low dust working environment | To be demonstrated | To be demonstrated

Emissions to air shall be counted from the relevant point source(s) stated in point (1) above where emissions can be continuously or periodically monitored from a fixed sampling point after any exhaust gas abatement system(s).

Emissions to water shall be considered as sulphate or chloride present in any treated wastewater effluent that is discharged into any rivers, lakes, transitional waters, coastal waters or seawaters.

The relevant limit for chloride emissions to water shall be based on the weighted average % TiO2 content of ore(s) used during the calculation period.

A low dust working environment shall, as a minimum, include the follows aspects:

A risk assessment for the workplace that identifies all the main areas of potential dust emission and worker exposure to dust.

The need to have in place an occupational hygiene workplace monitoring program.

Provision of appropriate training to employees about good practice for dust control.

Provision of adequate personal protective equipment to employees and visitors.

Assessment and verification

The applicant shall declare the content of TiO2 used in each of the product formulations subject to the EU Ecolabel license application. For any products with more than 3,0 % w/w TiO2 pigment content, the applicant shall also declare the supplier or suppliers of the TiO2 used in those products.

The applicant declaration shall be supported by declarations from their TiO2 supplier(s) (or TiO2 producer(s), if different) stating:

The type of TiO2 production process used (chloride or sulphate).

The applicable TiO2 content range of the weighted average ore in case of the chloride process.

Annual average emissions data of dust to air, SO2 to air, and SO42- to water for TiO2 produced through the sulphate process. Alternatively, average emission data of dust to air, HCl to air, and Cl- to water for TiO2 produced through the chloride process.

The declarations from TiO2 supplier(s) (or TiO2 producer(s), if different) should include the relevant European or international standards used to measure the relevant parameters listed in the Table 1.

The measures in place to ensure a low dust working environment.

The declaration from the TiO2 supplier(s) (or TiO2 producer(s), if different) shall include a basic calculation about how the annual average emissions were obtained. If the production of the supplied TiO2 pigment is non-continuous, then emission data calculations covering a shorter period than 12 months may be accepted. In cases of continuous monitoring, the annual average emission concentrations shall be derived from daily average concentrations. For periodically monitored emissions, at least 3 samples must be taken to derive the average results. Any periodic sampling must be taken during periods of stable operation that are representative of normal plant conditions for the production of the TiO2 pigments used in the EU Ecolabel paint products.

The emission calculations shall only be required to be submitted at the date of application for the EU Ecolabel. If the EU Ecolabel is awarded, the applicant can simply request updated declarations each year from their TiO2 supplier(s) of continuing compliance with the emission limits.

For emissions to air, concentrations shall be expressed in units of mg/Nm3 and multiplied by a specific emission air flow rate in units of Nm3/tonne TiO2 pigment production for the same time period that the data was collected. If there is more than one exhaust gas abatement system for major point sources of emissions to air, emissions from the clean air from each abatement system shall be counted and added.

For emissions to water, either a direct measurement or a mass balance approach shall be used. The mass balance approach shall be based on the balance between inputs of raw sulphate/chloride and outputs of sulphate/chloride in by-products, in emissions to air and in solid waste that is disposed of to landfill or incinerated. The difference in the masses of the inputs and outputs shall be considered as the mass of sulphate/chloride that is emitted to water during the calculation period and shall be divided by the estimated quantity of TiO2 pigment produced during the same period to calculate specific emissions to water in units of kg sulphate or chloride/t TiO2 pigment.

With the direct measurement approach for emissions to water, measured concentrations in units of g/m3 shall be multiplied by a specific treated wastewater effluent flow rate in units of m3/tonne TiO2 pigment production for the same time period that the sulphate/chloride data was collected.

In order to demonstrate the efficiency in use of aerosol spray paints the following tests and requirements shall be undertaken:

Note 1: This requirement does not apply to any aerosol products that are designed to apply transparent or semi-transparent coatings.

Note 2: If tinting systems are used to make different aerosol paint shades, only to the tinting base containing the most TiO2 needs to be tested. In cases where this tinting base is unable to achieve this requirement, the criterion shall be met after tinting the base to produce the standard colour RAL 9010.

Note 3: This requirement applies to white aerosol spray paints. For families of aerosol spray paints available only in preset shades, the spreading rate shall apply to the lightest colour.

Aerosol spray paints shall have a spreading rate of at least 2,0 m2 per litre while ensuring a hiding power of at least 98 % according to relevant European or international standards. The volume unit in the spreading rate calculation shall refer to the declared volume of the ready to use spray can.

Assessment and verification:

The applicant shall provide a declaration of compliance with the spreading rate limits or a justification of non-applicability of the spreading rate requirement for each of the products covered by the EU Ecolabel application. The declaration shall be supported by test results according to the method in relevant European or international standards. In cases where a result covers multiple products, it shall be clearly indicated which results correspond to which products covered by the EU Ecolabel license application.

Aerosol spray paints shall have an efficiency in spraying of at least 97 %, considered as the fraction of product in the ready to use spray can that is discharged from the can.

The test method shall consist of a calculation of the total content of product contained in the ready to use spray can that has not yet been operated. Prior to the test, the ready to use spray can shall be weighed. During the test, the contents of the can shall be continuously discharged onto a weighed surface at a steady rate in order to monitor the discharge rate. After the test, the spray can shall be weighed again to determine the total content of product discharged. The efficiency in spraying rate shall be calculated as

Efficiency in spraying %

total weight of product discharged during testg

total weight of product in can at beginning of test g

x100%

Assessment and verification:

The applicant shall provide a test report demonstrating the calculation of the efficiency in spraying rate. The report shall include the initial aerosol spray can weight, a plot of discharge rate versus time and the weight of the spray can at the end of the test. The total weight of product discharged shall be considered as the difference between the initial weight and the final weight of the can.

Note 1: This requirement does not apply to any aerosol products that are designed to apply transparent or semi-transparent coatings.

Aerosol spray paint shall achieve an adhesion score of 2 or less in the test for adhesion in relevant European or international standards.

Assessment and verification:

The applicant shall provide a declaration of compliance with the relevant requirement or a justification of the non-applicability of the requirements for each of the products covered by the EU Ecolabel application. The declaration shall be supported by test results according to the method in relevant European or international standards, as applicable.

Aerosol spray paint, when applied to blasted steel panels with a dry film thickness of at least 60μm, shall ensure adequate corrosion resistance after being subjected to a salt spray test of 240 hours duration according to relevant European or international standards.

After exposure, the coating shall meet the following criteria:

A rating of 3 or better (i.e. 0, 1 or 2) for size of blisters according to relevant European or international standards.

A rating of 3 or better (i.e. 0, 1 or 2) for quantity of blisters according to relevant European or international standards.

A rating of Ri2 or better (i.e. Ri0 or Ri1) for degree of rusting according to relevant European or international standards.

A delamination result of 4mm or less according to relevant European or international standards.

An adhesion score of 2 or less according to relevant European or international standards.

Assessment and verification:

The applicant shall provide a declaration of compliance supported by test results according to relevant European or international standards for salt spray test, for rust, for blistering, for delamination and adhesion

Aerosol spray paint, when applied to blasted steel panels with a dry film thickness of at least 60μm, shall ensure adequate weathering resistance after being subjected to 500 hours of weathering cycles according to relevant European or international standards.

After exposure, the coating shall meet the following criteria according to relevant European or international standards:

Colour change of ΔΕ ≤ 4.

Decrease of gloss of ≤ 30 %.

Degree of flaking of ≤ 2 in terms of flake density and ≤ 2 in terms of flake size.

Degree of blistering of ≤ 3 in terms of blister density and ≤ 3 in terms of blister size.

Degree of cracking of ≤ 2 in terms of crack size.

Assessment and verification:

The applicant shall provide a declaration of compliance supported by test results of coated substrates before and after the weathering exposure according to relevant European or international standards: for colour deviation; for gloss level deviation; for degree of flaking; for degree of cracking, and for degree of blistering.

The maximum VOC content permitted in aerosol spray paints shall not exceed the limits defined in Table 2. The VOC content shall be determined separately for each component and then added together.

The VOC content for the liquid paint component shall first be determined either by calculation based on the ingredients and raw materials or by using the methods given in relevant European or international standards. Then the VOC content for the paint component (in g/l liquid paint) shall be converted to units of g/l of ready to use product by multiplying by the aerosol spray paint volume ratio, defined as:

Aerosol spray paint volume ratio

X Litres of liquid paint

Y Litres of declared aerosol spray can volume

Unless otherwise demonstrated, the propellant, whether it is an individual substance or mixture, shall be assumed to be 100 % VOC. The amount of propellant VOC in the ready to use product shall be calculated based on a declared propellant content (in units of g propellant/l volume of the aerosol can). The mass of propellant added per litre of aerosol shall be calculated by the manufacturer.

[‘Volatile organic compounds (VOCs)’ means any organic compounds having an initial boiling point less than or equal to 250 °C measured at a standard pressure of 101,3 kPa]

VOC content limits

Liquid paint component | Propellant | Final product

VOC limits (expressed in terms of g/l of aerosol)

60 g/l | 290 g/l | 350 g/l

Assessment and verification:

The applicant shall provide a declaration of compliance supported by calculations of VOC content.

For the liquid paint component, the declaration of compliance shall be supported by calculations of VOC content based on the ingredients and raw materials used in the liquid paint component. Alternatively, the VOC content of the liquid paint component shall be communicated via a representative test report or reports using the methods given in relevant European or international standards and results, when corrected for the water-based aerosol spray paint volume ratio, shall demonstrate compliance with the limit.

For the propellant component, the applicant shall declare the propellant(s) used and provide details of the calculation.

Note: These sub-criteria apply to the final product formulation and any supplied ingredients therein.

The final product formulation and any supplied ingredients therein shall not contain any ingoing substances that meet the criteria referred to in Article 57 of Regulation (EC) No 1907/2006 that have been identified according to the procedure described in Article 59 of that Regulation and included in the candidate list for substances of very high concern for authorisation.

Assessment and verification:

The applicant shall provide a signed declaration that the final product formulation and any supplied ingredients therein do not contain any SVHCs as ingoing substances. The applicant declaration shall be supported by safety data sheets of all supplied ingredients used to produce the final product and declarations from the chemical suppliers.

The list of substances identified as SVHCs and included in the candidate list in accordance with Article 59 of Regulation (EC) No 1907/2006 can be found here:

https://www.echa.europa.eu/candidate-list-table

Reference to the list shall be made on the submission date of the EU Ecolabel application.

For any level of known impurities identified as SVHCs in ingredients, the concentration of the impurity and an assumed retention factor of 100 % shall be used to estimate the quantity of the SVHC impurity remaining in the final product formulation. Impurities that are SVHCs cannot be present in the paint or varnish product formulation above 0,0100 % w/w or in any individual ingredient in concentrations exceeding 0,100 % w/w. Any deviation from a retention factor of 100 % for an SVHC impurity (for example due to solvent evaporation) or in case of chemical modification, must be supported by adequate justifications.

The final product formulation shall not be classified as being carcinogenic, mutagenic, toxic for reproduction, acutely toxic, an aspiration hazard, a specific target organ toxicant, a respiratory or skin sensitiser, hazardous to the aquatic environment, hazardous to the ozone layer, an endocrine disruptor, persistent, bioaccumulative and toxic (PBT) or persistent, mobile and toxic (PMT) in accordance with Regulation (EC) No 1272/2008 and specifically in terms of the hazard statement codes stated in Table 3. The only exception permitted to this rule shall be the H412 and H413 classification, and only if due to levels of dry-film preservatives in the case of outdoor paints or varnishes.

Unless derogated in Table 4, the final product formulation shall not contain any ingoing substances in concentrations at or above 0,010 % weight by weight of the final product formulation that are classified, in accordance with Regulation (EC) No 1272/2008, with any of the hazard classes, categories and associated hazard statement codes stated in Table 3.

Carcinogenic, mutagenic or toxic for reproduction (CMR)

Categories 1A and 1B | Category 2

H340: May cause genetic defects | H341: Suspected of causing genetic defects

H350: May cause cancer | H351: Suspected of causing cancer

H350i: May cause cancer by inhalation |

H360: May damage fertility or the unborn child | H361: Suspected of damaging fertility or the unborn child

H360F: May damage fertility | H361f: Suspected of damaging fertility

H360D: May damage the unborn child | H361d: Suspected of damaging the unborn child

H360FD: May damage fertility. May damage the unborn child | H361fd: Suspected of damaging fertility. Suspected of damaging the unborn child

H360Fd: May damage fertility. Suspected of damaging the unborn child. | H362: May cause harm to breast fed children

H360Df: May damage the unborn child. Suspected of damaging fertility. |

Acute toxicity

Categories 1 and 2 | Category 3

H300: Fatal if swallowed | H301: Toxic if swallowed

H310: Fatal in contact with skin | H311: Toxic in contact with skin

H330: Fatal if inhaled | H331: Toxic if inhaled

EUH070: Toxic by eye contact

Aspiration hazard

Category 1 |

H304: May be fatal if swallowed and enters airways |

Specific target organ toxicity

Category 1 | Category 2

This article is long: the rest is at the official publication.