For the purposes of this Annex, ‘competent authority’ shall mean the authority specified in point AR.UAS.GEN.010(a) of Annex I (Part-AR.UAS) to Implementing Regulation (EU) 2024/1109.
For the purposes of this Annex, ‘owner of the UA’ shall mean one of the following:
the registered owner of the UA, which may be the UAS operator itself;
the UAS operator being the lessee of the UA, provided point ML.UAS.201(b) applies.
This Annex establishes the measures to be taken by the persons and organisations to ensure that the UAS operated in the ‘specific’ category as defined in Article 5 of Implementing Regulation (EU) 2019/947, and for which an airworthiness certificate has been or will be issued to the UA in accordance with Article 7(2) of Implementing Regulation (EU) 2019/947, is airworthy. It also specifies the conditions to be met by the persons or organisations involved in the tasks related to the airworthiness of that UAS.
The owner of the UA shall be accountable for the continuing airworthiness of the UAS and shall ensure that no flight takes place unless all the following requirements are met:
the UAS is maintained in an airworthy condition;
any operational and emergency equipment fitted to the UAS is correctly installed and serviceable, or if that equipment is unserviceable, it is clearly identified as such;
the UA airworthiness certificate is valid.
By way of derogation from point (a), when the UA is leased, the accountability set out in point (a) shall apply to the lessee, provided that the lessee is identified in the registration document of the UA or such transfer of accountability is detailed in the leasing contract.
Any person or organisation that performs maintenance on the UAS and its components shall be responsible for the maintenance tasks performed.
The UAS operator shall be responsible for the satisfactory accomplishment of the pre-flight inspection. The person carrying out that inspection on behalf of the UAS operator shall be qualified for that purpose. The pre-flight inspection need not be carried out by an approved maintenance organisation or by certifying staff.
In addition to the requirements laid down in point (a), the owner of the UA shall ensure that:
the tasks associated with the continuing airworthiness management of the UAS are performed by an organisation that is approved in accordance with Annex II (Part-CAO.UAS) and has its principal place of business in a territory to which the Treaties apply.
If a Part-CAO.UAS organisation is contracted by the owner of the UA as regards the performance of those tasks, a written contract shall be established in accordance with Appendix 1. That contracted organisation shall assume responsibility for the proper performance of those tasks;
unless otherwise specified in Subpart E, the maintenance of the UAS and the components for installation thereto is performed by an organisation that is approved in accordance with Annex II (Part-CAO.UAS) and has its principal place of business in a territory to which the Treaties apply.
To determine whether the UAS complies with the requirements of this Annex, the owner of the UA shall ensure that access to the UAS and UAS records is granted to any person authorised by the competent authority.
The continuing airworthiness of the UAS and the serviceability of operational and emergency equipment shall be ensured by the following:
the accomplishment of pre-flight inspections of the UA;
the performance of unscheduled maintenance and the rectification of defects (including damages) in accordance with the data specified in points ML.UAS.401 and ML.UAS.304, as applicable, while taking into account the minimum equipment list (‘MEL’) and the configuration deviation list (‘CDL’), when they exist;
the accomplishment of all scheduled maintenance in accordance with the UAS maintenance programme referred to in point ML.UAS.302;
compliance with any applicable:
airworthiness directive (‘AD’) issued or adopted by the European Union Aviation Safety Agency;
operational requirements with a continuing airworthiness impact;
continuing airworthiness requirements mandated by the Agency;
measure required by the competent authority in immediate reaction to a safety problem;
the accomplishment of modifications and repairs in accordance with point ML.UAS.304;
maintenance check flights (‘MCFs’), when necessary;
the availability of the mass and balance statement reflecting the current configuration of the UA, when such information is produced by the UA manufacturer.
The scheduled maintenance of the UAS shall be organised in accordance with an UAS maintenance programme.
The UAS maintenance programme, and any subsequent amendments to it, shall be approved by the Part-CAO.UAS organisation that is responsible for managing the continuing airworthiness of the UAS.
The UAS maintenance programme shall comply with:
the mandatory continuing airworthiness information, such as repetitive ADs, the airworthiness limitations section (‘ALS’) of the instructions for continuing airworthiness (‘ICAs’), and specific maintenance requirements contained in the type-certificate data sheet (‘TCDS’);
the ICAs issued by the design approval holder (DAH);
Notwithstanding point (c)(1), by way of derogation from point (c)(2), the UAS maintenance programme may deviate from the ICAs, based on data obtained from reviews performed in accordance with point (f).
The UAS maintenance programme shall take into account the UAS configuration, and the type and specificities of operations.
The UAS maintenance programme shall be reviewed at least annually in order to assess its effectiveness while considering new or modified ICAs.
Any applicable AD must be applied according to the requirements of that AD unless otherwise specified by the Agency.
Any damage to an UAS or to a component for installation thereto shall be assessed before being repaired.
Carrying out modifications and repairs on the UAS or its components shall require such modifications and repairs to be either:
approved by the Agency; or
approved by a design organisation that complies with Annex I (Part 21) to Regulation (EU) No 748/2012; or
contained in the requirements of point 21.A.90B or point 21.A.431B of Annex I (Part 21) to Regulation (EU) No 748/2012.
For each UAS, as identified by the UA registration and control and monitoring unit (‘CMU’) type and serial number, a system shall be established to record continuing airworthiness information of the UAS. That system shall be used by the remote pilot and the person(s) involved in the continuing airworthiness of the UAS.
The UAS continuing airworthiness record system shall record the following:
the date of the entry and the corresponding total usage, in the parameter(s) relevant to the UAS (e.g. flight hours, calendar time or cycles);
details of the maintenance performed on the UAS, in particular all certificates of release to service required by points ML.UAS.801 or ML.UAS.803;
details of the CMU installation, in particular the certificate of release to service (‘CRS’) required by point ML.UAS.805, when such installation is prescribed by the design approval holder (DAH);
evidence confirming the satisfactory accomplishment of the UA pre-flight inspection;
information considered necessary to ensure continued flight safety;
the current mass and balance statement, when such information is produced by the UA manufacturer;
any other data necessary to demonstrate compliance with point (g).
With respect to components subject to airworthiness limitations, in addition to the authorised release document (EASA Form 1 or equivalent), the following information shall be entered in the record system:
the designation and identification of the component(s);
the type, serial number and registration, as appropriate, of the UA, the CMU or the component to which the particular component has been fitted, along with the reference to the maintenance records relevant to its installation and removal;
the date of the entry and the corresponding component’s accumulated total usage, in the parameter(s) relevant to the particular component;
Each entry shall be made as soon as possible following the completion of the task so that it provides an up-to-date status to the remote pilot.
All entries made in the UAS continuing airworthiness records shall be clear and accurate. When it is necessary to correct an entry, the correction shall be made in a manner that clearly shows the original entry.
The record system shall include logs for the UA, the CMU and, as appropriate, for the components that are subject to airworthiness limitations.
The UAS continuing airworthiness record system shall be able to provide:
the current status of ADs and measures mandated by the competent authority in immediate reaction to a safety problem;
the current status of modifications and repairs;
the current status of compliance with the UAS maintenance programme;
the current status of components that are subject to airworthiness limitations;
the current list of deferred maintenance.
The records shall be kept for the periods specified below:
for the records specified in points (b)(2) and (b)(3), until the time the information contained in the records is superseded by new information equivalent in scope and detail but not less than 36 months after the maintenance or, as applicable, the CMU installation, has been released;
for the records specified in points (b)(1), (b)(7) and point (c), for at least 12 months after the UAS or the component has been permanently withdrawn from service;
for the records specified in points (b)(4) to (b)(6), not less than 36 months after the entry into the record system;
if not superseded, the records referred to in point (h)(1) shall be kept for 12 months after the UA or the CMU has been permanently withdrawn from service.
When an UA is permanently transferred from one owner to another, the relevant continuing airworthiness records referred to in point ML.UAS.305 shall also be transferred.
When the owner of the UA contracts the continuing airworthiness management tasks to a Part-CAO.UAS organisation, the owner of the UA shall ensure that the continuing airworthiness records referred to in point ML.UAS.305 are transferred to the contracted organisation.
The periods for the retention of the records set out in point ML.UAS.305(h) shall continue to apply to the new owner or Part-CAO.UAS organisation.
Maintenance on the UAS shall require the use of and adherence to current applicable maintenance data.
For the purposes of this Annex, ‘applicable maintenance data’ means any of the following:
any applicable requirement, procedure, standard or information issued by the competent authority or the Agency;
any applicable AD;
the applicable ICAs and other maintenance instructions issued by the type-certificate holder, supplementary type-certificate holder and any other organisation that publishes such data in accordance with Annex I (Part 21) to Regulation (EU) No 748/2012;
for components approved for installation by the design approval holder (‘DAH’), the applicable maintenance instructions published by the component manufacturer and acceptable to the DAH.
Any UAS defect that seriously endangers the flight safety shall be rectified before further flight.
The following persons may decide that a defect does not seriously endanger flight safety, and may defer its rectification accordingly:
the remote pilot or the authorised certifying staff in respect of defects that affect non-required UAS equipment;
the remote pilot or the authorised certifying staff when using the MEL or the CDL in respect of defects that affect required UAS equipment;
the authorised certifying staff in respect of defects other than those referred to in points (b)(1) and (b)(2).
Any UAS defect that does not seriously endanger flight safety shall be rectified as soon as practicable from the date on which the defect was first identified and within the time limits specified in the maintenance data or the MEL.
Any defect that is not rectified before flight shall be recorded in the UAS continuing airworthiness record system referred to in point ML.UAS.305, and a record shall be made available to the remote pilot.
Unless otherwise specified in Annex II (Part-CAO.UAS) or in point 21.A.307 of Annex I (Part 21) to Regulation (EU) No 748/2012, a component may be fitted to an UA only if all the following conditions are met:
it is in a satisfactory condition;
it has been appropriately released to service using an EASA Form 1 as set out in Appendix II to Annex I (Part-M) to Regulation (EU) No 1321/2014 or equivalent;
it has been marked in accordance with Subpart Q of Annex I (Part 21) to Regulation (EU) No 748/2012.
Prior to the installation of a component on an UA, the maintenance organisation shall ensure that the particular component is eligible to be fitted taking into account the UA configuration and any applicable AD.
Standard parts shall be fitted to an UA or to a component only when the maintenance data specifies those particular standard parts, when accompanied by evidence of conformity to the applicable standard, and when they have appropriate traceability.
Raw or consumable materials shall only be used on an UA or a component provided that:
the aircraft or component manufacturer allows for the use of such raw or consumable materials in relevant maintenance data;
such materials meet the required material specifications and have appropriate traceability;
such materials are accompanied by documentation that clearly relates to those particular materials and contains a statement of conformity to applicable specifications, and also the manufacturing and supplier source.
The maintenance of UA components shall be certified in accordance with the following table:
Certified using an EASA Form 1 (as set out in Appendix II to Annex I (Part-M) to Regulation (EU) No 1321/2014) | Certified together with UA maintenance in accordance with point ML.UAS.801 (not possible to issue an EASA Form 1)
Components maintained in accordance with component maintenance data (data issued by the component manufacturer)
Maintenance other than overhaul |
For engines: Engine-rated maintenance organisations
For other components: component-rated maintenance organisations
UA maintenance organisations
Overhaul of components other than engines | Component-rated maintenance organisations | Not possible
Overhaul of engines | Engine-rated maintenance organisations | UA maintenance organisations if foreseen by the design approval holder
Components maintained in accordance with UA maintenance data (data issued by the UA manufacturer)
All components and all types of maintenance | Engine-rated (for engines) or component-rated (for other components) maintenance organisations | UA maintenance organisations
The components referred to in points (b)(3) to (b)(6) of point 21.A.307 of Annex I (Part 21) to Regulation (EU) No 748/2012 may be maintained by any person or organisation. In such case, by way of derogation from point (a), the maintenance of those components shall be released with a ‘declaration of maintenance accomplished’ issued by the person or organisation that has performed the maintenance. The ‘declaration of maintenance accomplished’ shall contain at least basic details of the maintenance performed, the date on which the maintenance was completed, and the identification of the organisation or the person that issues it. It shall be considered a maintenance record and equivalent to an EASA Form 1 in respect of the maintained component.
Unserviceable and unsalvageable components shall be segregated from serviceable components, standards parts, and materials.
A component shall be considered unserviceable in any of the following circumstances:
upon reaching the component’s limitation as defined in the UAS maintenance programme;
non-compliance with applicable ADs and other continuing airworthiness requirements mandated by the Agency;
absence of the necessary information to determine the airworthiness status of the component or its eligibility for installation;
evidence of component defects or malfunctions;
involvement of the component in an incident or accident that has likely affected its serviceability.
Components which have reached their certified life limits or contain a non-repairable defect or malfunction shall be classified as unsalvageable and shall not be permitted to re-enter the component supply system unless their certified life limits have been extended or a repair solution has been approved in accordance with point ML.UAS.304.
Components shall be installed on a CMU only when the maintenance data specifies those components and when they are in a satisfactory condition.
Notwithstanding point (a), critical CMU components referred to in point 21.A.308(a) of Annex I (Part 21) to Regulation (EU) No 748/2012 shall be installed on the CMU only if accompanied by an EASA Form 1 or equivalent, and marked in accordance with Subpart Q of Annex I (Part 21) to Regulation (EU) No 748/2012.
Notwithstanding point (a), CMU components that are not deemed critical shall be installed on the CMU only if accompanied by the declaration specified in point 21.A.308(b) of Annex I (Part 21) to Regulation (EU) No 748/2012, or equivalent.
The maintenance of critical CMU components shall be performed by a maintenance organisation approved in accordance with Annex II (Part-CAO.UAS) and shall be certified on an EASA Form 1 as set out in Appendix II to Annex I (Part-M) to Regulation (EU) No 1321/2014.
CMU components that are not deemed critical may be maintained by any person or organisation. The maintenance of those components shall be released with a ‘declaration of maintenance accomplished’ issued by the person or organisation that has performed the maintenance. That declaration shall contain at least basic details of the maintenance performed, the date on which the maintenance was completed, and the identification of the organisation or the person that issues it. It shall be considered a maintenance record and equivalent to the declaration referred to in point 21.A.308(b) of Annex I (Part 21) to Regulation (EU) No 748/2012 for the purpose of installation.
By way of derogation from points (d) and (e), where the CMU components are subject to maintenance while they are installed on, or temporarily removed from, the CMU, such maintenance may be certified together with the CMU maintenance in accordance with point ML.UAS.803.
When completed, the maintenance performed on an UA shall be certified on a ‘certificate of release to service’ (‘CRS’) by a certifying staff. The CRS shall be issued when that certifying staff has verified that all the maintenance that was ordered has been properly performed taking into account the availability and use of the maintenance data specified in point ML.UAS.401.
A CRS shall contain at least the following:
basic details of the UA maintenance performed;
the date on which the UA maintenance was certified;
the approval reference of the maintenance organisation and certifying staff issuing the CRS;
the limitations to airworthiness or operations, if any.
By way of derogation from point (a), when ordered maintenance cannot be completed, a CRS may be issued within the approved UA limitations. In that case, the CRS shall indicate that the maintenance could not be completed, and also indicate any applicable airworthiness or operations limitations as part of the information required in point (b)(4).
A CRS shall not be issued in the case of any known non-compliance with the requirements of this Annex which endangers flight safety.
When completed, the maintenance performed on an UA component shall be certified by a certifying staff except for the cases covered by point ML.UAS.502(b). The certification shall be issued when that certifying staff has verified that all the maintenance that was ordered has been properly performed taking into account the availability and use of the maintenance data specified in point ML.UAS.401 and that the component is in a satisfactory condition.
That certification shall be established on an EASA Form 1, except when such maintenance is certified together with UA maintenance, as indicated in point ML.UAS.502(a).
The EASA Form 1 referred to in point (b) shall be filled in accordance with the instructions provided in Appendix 3. It may be generated from a computer database.
When completed, the maintenance performed on the CMU that involves any component which is critical for the UAS operation as determined by the DAH, shall be certified on a CRS by a certifying staff. The CRS shall be issued when that certifying staff has verified that all the maintenance that was ordered has been properly performed taking into account the availability and use of the maintenance data specified in point ML.UAS.401.
A CRS shall contain at least the following:
basic details of the CMU maintenance performed;
the date on which the CMU maintenance was certified;
the approval reference of the maintenance organisation and certifying staff issuing the CRS;
the limitations to airworthiness or operations, if any.
A CRS shall not be issued in the case of any known non-compliance with the requirements of this Annex which endangers flight safety.
When completed, the maintenance performed on a CMU component in accordance with point ML.UAS.520(d) shall be certified by a certifying staff. The certification shall be issued when that certifying staff has verified that all the maintenance that was ordered has been properly performed taking into account the availability and use of the maintenance data specified in point ML.UAS.401 and that the component is in a satisfactory condition.
That certification shall be established on an EASA Form 1, except when such maintenance is certified together with CMU maintenance, as indicated in point ML.UAS.520(f).
The EASA Form 1 referred to in point (b) shall be filled in accordance with the instructions provided in Appendix 3. It may be generated from a computer database.