4 Appendix 3, Regulation (EU) 2024/1107

In forcesince 13 Mar 2024

These instructions relate only to the use of the EASA Form 1, as specified in Appendix II to Annex I (Part-M) to Regulation (EU) No 1321/2014, for UAS maintenance purposes.

Attention is drawn to the instructions specified in Appendix II to Annex I (Part-M) to Regulation (EU) No 1321/2014 which cover the use of the EASA Form 1 for maintenance purposes in manned aviation, and the instructions specified in Appendix I to Annex I (Part 21) to Regulation (EU) No 748/2012 which cover the use of the EASA Form 1 for production purposes.

1.1. The primary purpose of the certificate is to declare the airworthiness of the maintenance work performed on UAS components (‘the item(s)’).

1.2. Correlation must be established between the certificate and the item(s). The originator must retain the certificate in a form that allows the verification of the original data.

1.3. The certificate is acceptable to many airworthiness authorities, but may be dependent on the existence of bilateral agreements and/or the policy of a particular airworthiness authority.

1.4. The certificate is not a delivery or shipping note.

1.5. UA are not to be released using the certificate.

1.6. The certificate does not constitute approval to install the item(s) but helps the end user determine its (their) airworthiness approval status.

1.7. A mixture of production- and maintenance-released items is not permitted with the same certificate.

2.1. The certificate must comply with the defined format, including block numbers, and the location of each block. The size of each block may, however, be amended to suit the individual application, but not to the extent that would render the certificate unrecognisable.

2.2. The certificate must be in ‘landscape’ orientation, but the overall size may be significantly increased or decreased as long as the certificate remains recognisable and legible. If in doubt, please consult your competent authority.

2.3. The user/installer responsibility statement can be placed on either side of the form.

2.4. All printing must be clear and legible to allow easy reading.

2.5. The certificate may either be pre-printed or computer generated, but in either case the printing of lines and characters must be clear and legible and in accordance with the defined format.

2.6. The certificate should be in English and, if appropriate, in one or more other languages.

2.7. The details to be entered on the certificate may be either machine/computer printed or handwritten, using capital letters and must allow easy reading.

2.8. Limit the use of abbreviations to a minimum, to aid clarity.

2.9. The space remaining on the reverse side of the certificate may be used by the originator for any additional information, but must not include any certification statement. Any use of the reverse side of the certificate must be referenced in the appropriate block on the front side of the certificate.

3.1. If an end user finds an error(s) on a certificate, the end user must inform in writing the originator. The originator may issue a new certificate only if the error(s) can be verified and corrected.

3.2. The new certificate must have a new tracking number, signature, and date.

3.3. The request for a new certificate may be honoured without reverification of the item’s (items’) condition. The new certificate is not a statement of the current condition and should refer to the previous certificate in Block 12 with the following statement: ‘This certificate corrects the error(s) in Block(s) [enter block(s) corrected] of the certificate [enter original tracking number] dated [enter original issue date], and does not cover conformity/condition/release to service.’

Both certificates should be retained in accordance with the retention period associated to the first certificate.

State the name and the country of the competent authority under whose jurisdiction this certificate is issued. When the competent authority is the Agency, only ‘EASA’ must be stated.

‘AUTHORISED RELEASE CERTIFICATE

EASA FORM 1’

Enter the unique number established by the numbering system/procedure of the organisation identified in Block 4; this may include alphanumeric characters.

Enter the full name and address of the approved organisation that certifies the work covered by this certificate. Logos, etc., are permitted provided they can be contained within the block.

To facilitate customer traceability of the item(s), enter the work order number, contract number, invoice number, or similar reference number.

Enter line item numbers when there is more than one line item. This block allows easy cross-referencing to the Remarks in Block 12.

Enter the name or description of the item. Preference should be given to the term used in the instructions for continuing airworthiness (‘ICAs’) or maintenance data (such as illustrated parts catalogue, aircraft maintenance manual, service bulletin, component maintenance manual).

Enter the part number as it appears on the item or tag/packaging. In case of an engine or propeller, the type designation may be used.

State the quantity of items.

If the item is required by applicable regulations to be identified with a serial number, enter it here. Additionally, any other serial number not required by applicable regulations may also be entered. If there is no serial number identified on the item, enter ‘N/A’.

The following describes the permissible entries for Block 11. Enter only one of these terms – where more than one may be applicable, use the one that most accurately describes the majority of the work performed and/or the status of the article.

[‘Applicable standard’ means a manufacturing/design/maintenance/quality standard, method, technique or practice approved by or acceptable to the competent authority. The applicable standard shall be described in Block 12.]

(i)

| Overhauled | Means a process that ensures the item is in complete conformity with all applicable service tolerances specified in the maintenance data. The item will be at least disassembled, cleaned, inspected, repaired as necessary, reassembled and tested in accordance with the data specified above.

(ii)

| Repaired | Rectification of defect(s) using an applicable standard.

(iii)

| Inspected/Tested | Examination, measurement, etc., in accordance with an applicable standard (e.g. visual inspection, functional testing, bench testing, etc.).

(iv)

| Modified | Alteration of an item to conform to an applicable standard

Describe the work identified in Block 11, either directly or by reference to supporting documentation, necessary for the user or installer to determine the airworthiness status of the item(s) in relation to the work being certified. If necessary, a separate sheet may be used and referenced from the main EASA Form 1. Each statement must clearly identify which item(s) in Block 6 it relates to.

Examples of information to be entered in Block 12 are as follows:

(i)

maintenance data used, including revision status and reference;

(ii)

compliance with airworthiness directives (ADs) or service bulletins (SBs);

(iii)

repairs performed;

(iv)

modifications performed;

(v)

replacement parts installed;

(vi)

status of life-limited parts;

(vii)

deviations from the customer work order;

(viii)

certification statements other than those referred to in point 145.A.50 of Annex II (Part-145) to Regulation (EU) No 1321/2014;

(ix)

information needed to support shipment with shortages or reassembly after delivery.

Include the following component CRS statement:

□ ‘Certifies that, unless otherwise specified in this block, the work identified in Block 11 and described in this block has been accomplished in accordance with the requirements of Annex II (Part-CAO.UAS) to Delegated Regulation (EU) 2024/1107, and in respect to that work the item is considered ready for release to service.’

If printing the data from an electronic EASA Form 1, any appropriate set of data that is not fit for other blocks should be entered in this block.

General requirements for Blocks 13a–13e: Not used for maintenance release. Shade, darken, or otherwise mark to preclude inadvertent or unauthorised use.

Tick the box ‘other regulations specified in Block 12’ and enter the Part-CAO.UAS certification statement in Block 12. If the maintenance is also certified by the organisation under Annex II (Part-145) to Regulation (EU) No 1321/2014, tick also the box ‘Part-145.A.50 Release to Service’.

If other regulations than Part-CAO.UAS and Part-145 are meant with the tick in the box ‘other regulations’, then these regulations must be identified in Block 12. At least one box must be marked, or both boxes may be marked, as appropriate.

The certification statement ‘unless otherwise specified in this block’ is intended to address the following cases:

(a)

where maintenance could not be completed;

(b)

where the accomplishment of the maintenance deviated from the relevant regulatory requirements;

(c)

where maintenance has been performed in accordance with a requirement other than those specified in Part-145 or in Part-CAO.UAS; in this case, Block 12 shall specify the particular regulation.

This block shall be completed with the signature of the authorised person. Only persons specifically authorised under the rules and policies of the competent authority are permitted to sign this block. To aid recognition, a unique number identifying the authorised person may be added.

Enter the certificate/approval number(s)/reference(s). Such number/reference is issued by the competent authority.

Enter the name of the person that signs Block 14b in a legible form.

Enter the date on which Block 14b is signed; the date must be in the format dd = 2-digit day, mmm = first 3 letters of the month, yyyy = 4-digit year.

User/Installer Responsibilities

Place the following statement on the certificate to notify end users that they are not relieved of their responsibilities concerning the installation and use of any item accompanied by the form:

‘This certificate does not automatically constitute authority to install the item(s).

Where the user/installer performs work in accordance with regulations of an airworthiness authority different than the airworthiness authority specified in block 1, it is essential that the user/installer ensures that his/her airworthiness authority accepts items from the airworthiness authority specified in block 1.

Statements in blocks 13a and 14a do not constitute installation certification. In all cases aircraft maintenance records must contain an installation certification issued in accordance with the national regulations by the user/installer before the aircraft may be flown.’