Directive 2010/75/EU is amended as follows:
the title is replaced by the following:
‘Directive 2010/75/EU of the European Parliament and of the Council of 24 November 2010 on industrial and livestock rearing emissions (integrated pollution prevention and control)’
;
in Article 1, the second paragraph is replaced by the following:
‘It also lays down rules designed to prevent or, where that is not practicable, to continuously reduce emissions into air, water and land, to prevent the generation of waste, improve resource efficiency, and to promote the circular economy and decarbonisation, in order to achieve a high level of protection of human health and the environment taken as a whole.’
;
in Article 2, paragraph 1 is replaced by the following:
‘1. This Directive shall apply to the industrial activities giving rise to pollution referred to in Chapters II to VIa.’
;
Article 3 is amended as follows:
point (2) is replaced by the following:
‘(2) “pollution” means the direct or indirect introduction, as a result of human activity, of substances, vibrations, heat, noise or odours into air, water or land, which can be harmful to human health or the quality of the environment, result in damage to material property, or impair or interfere with amenities and other legitimate uses of the environment;’
;
point (3) is replaced by the following:
‘(3) “installation” means a stationary technical unit within which one or more activities listed in Annex I, in Annex Ia or in Part 1 of Annex VII are carried out, and any other directly associated activities on the same site which have a technical connection with the activities listed in those Annexes and which could have an effect on emissions and pollution;’
;
the following points are inserted:
‘(5a) “environmental performance limit value” means a performance value included in a permit, expressed for specified conditions in terms of certain specific parameters;’;
‘(9a) “deep industrial transformation” means the implementation by industrial operators of emerging techniques or best available techniques involving a major change in the design or technology of all or part of an installation or the replacement of an existing installation by a new installation, which allows an extremely substantial reduction of emissions of greenhouse gases in line with the objective of climate neutrality and optimises environmental co-benefits, at least to the levels that can be achieved by techniques identified in the applicable BAT conclusions, taking into account cross-media effects;’
;
points (b) and (c) of point (10) are replaced by the following:
‘(b) “available techniques” means techniques developed on a scale which allows implementation in the relevant industrial sector, under economically and technically viable conditions, taking into consideration the costs and advantages, regardless of whether such techniques are used or produced in the Union, as long as they are reasonably accessible to the operator;
“best” means most effective in achieving a high general level of protection of the environment as a whole, including human health and climate protection;’
;
point (12) is replaced by the following:
‘(12) “BAT conclusions” means a document containing the parts of a BAT reference document laying down the conclusions on best available techniques and emerging techniques, their description, information to assess their applicability, the emission levels associated with those techniques, the environmental performance levels associated with those techniques, the content of an environmental management system including benchmarks, associated monitoring, associated consumption levels and, where appropriate, relevant site remediation measures;’
;
the following points are inserted:
‘(12a) “operating rules” means the rules included in permits or general binding rules for the operation of activities referred to in Annex Ia, setting out the emission limit values, the environmental performance limit values, associated monitoring requirements, and, where relevant, land spreading practices, pollution prevention and mitigation practices, nutritional management, feed preparation, housing, manure management, including collection, storage, processing and land spreading of manure, and storage of dead animals, and which are consistent with the use of best available techniques;’;
‘(13a) “environmental performance levels associated with the best available techniques” means the range of environmental performance levels, obtained under normal operating conditions using a BAT or a combination of BATs; as described in BAT conclusions;’;
‘(13aa) “environmental performance” means the performance with regard to consumption levels, resource efficiency concerning materials, water and energy resources, the reuse of materials and water, and to waste generation;’;
‘(13b) “benchmarks” means the indicative range of environmental performance levels associated with best available techniques, which is to be used as a reference in the EMS;’
;
point (14) is replaced by the following:
‘(14) “emerging technique” means a novel technique for an industrial activity that, if commercially developed, could provide either a higher general level of protection of human health and the environment or at least the same level of protection of human health and the environment and higher cost savings than existing best available techniques;’
;
point (17) is replaced by the following:
‘(17) “the public concerned” means the public affected or likely to be affected by, or having an interest in, the taking of a decision on the granting or the updating of a permit or of permit conditions; for the purposes of this definition, non-governmental organisations promoting the protection of human health or the environment and meeting any requirements under national law shall be deemed to have an interest;’
;
point (23) is replaced by the following:
‘(23) “poultry” means poultry as defined in Article 4, point 9, of Regulation (EU) 2016/429 of the European Parliament and of the Council [Regulation (EU) 2016/429 of the European Parliament and of the Council of 9 March 2016 on transmissible animal diseases and amending and repealing certain acts in the area of animal health (“Animal Health Law”) (OJ L 84, 31.3.2016, p. 1).’;];
the following points are inserted:
‘(23a) “pigs” means pigs as defined in Article 2 of Council Directive 2008/120/EC [Council Directive 2008/120/EC of 18 December 2008 laying down minimum standards for the protection of pigs (OJ L 47, 18.2.2009, p. 5).’;];
“livestock unit” means a standard measurement unit that allows for the aggregation of the various categories of livestock in order for them to be compared, and is calculated by using the coefficients for individual livestock categories listed in Annex Ia;
the following points are added:
‘(48) “emission levels associated with emerging techniques” means the range of emission levels obtained under normal operating conditions using an emerging technique or a combination of emerging techniques, as described in BAT conclusions, expressed as an average over a given period of time, under specified reference conditions;
“environmental performance levels associated with emerging techniques” means the range of environmental performance levels, obtained under normal operating conditions, using an emerging technique or a combination of emerging techniques as described in BAT conclusions;
“compliance assurance” means mechanisms for securing compliance using three categories of intervention: compliance promotion; compliance monitoring; follow-up and enforcement.’
;
in Article 4(1), the second subparagraph is replaced by the following:
‘By way of derogation from the first subparagraph, Member States may set a procedure for the registration of installations covered only by Chapter V or Chapter VIa.’
;
in Article 5, the following paragraph is added:
‘4. Member States shall develop systems for the electronic permitting of installations and implement electronic permitting procedures by 31 December 2035.
The Commission shall organise an exchange of information with the Member States on electronic permitting and publish guidance on best practices.’
;
Articles 7 and 8 are replaced by the following:
Without prejudice to Directive 2004/35/EC of the European Parliament and of the Council [Directive 2004/35/EC of the European Parliament and of the Council of 21 April 2004 on environmental liability with regard to the prevention and remedying of environmental damage (OJ L 143, 30.4.2004, p. 56).’;], in the event of any incident or accident significantly affecting human health or the environment, Member States shall take the necessary measures to ensure that:
the operator informs the competent authority immediately;
the operator immediately takes the measures to limit the consequences for human health or the environment and to prevent further possible incidents or accidents; and
the competent authority requires the operator to take any appropriate complementary measures that the competent authority considers necessary to limit the consequences for human health or the environment and to prevent further possible incidents or accidents.
In the event of pollution affecting drinking water resources, including transboundary resources, or affecting waste water infrastructure in the case of indirect discharge, the competent authority shall inform the drinking water and waste water operators affected of the measures taken to prevent damage being caused, or remedy the damage caused, by that pollution to human health and the environment.
In the event of any incident or accident significantly affecting human health or the environment in another Member State, the Member State in whose territory the accident or incident has occurred shall ensure that the competent authority of the other Member State is immediately informed. Transboundary and multidisciplinary cooperation between the affected Member States shall be aimed at limiting the consequences for the environment and human health and to prevent further possible incidents or accidents.
Member States shall take the necessary measures to ensure that the permit conditions are complied with.
They shall also adopt compliance assurance measures to promote, monitor and enforce compliance with obligations placed on natural or legal persons under this Directive.
In the event of a breach of the permit conditions, Member States shall ensure that:
the operator immediately informs the competent authority;
the operator immediately takes the measures necessary to ensure that compliance is restored within the shortest possible time; and
the competent authority requires the operator to take any appropriate complementary measures that the competent authority considers necessary to restore compliance.
Where the breach of the permit conditions poses an immediate danger to human health or threatens to cause an immediate significant adverse effect upon the environment, and until compliance is restored in accordance with the second paragraph, points (b) and (c), the operation of the installation, combustion plant, waste incineration plant, waste co-incineration plant or relevant part thereof shall be suspended without any delay.
Where such breach threatens human health or the environment in another Member State, the Member State in whose territory the breach of the permit conditions has occurred shall ensure that the other Member State is informed.
In situations not covered by paragraph 3 of this Article, where a persistent breach of the permit conditions poses a danger to human health or causes a significant adverse effect upon the environment, and where the necessary action for restoring compliance identified in the inspection report referred to in Article 23(6) has not been implemented, the operation of the installation, combustion plant, waste incineration plant, waste co-incineration plant or relevant part thereof may be suspended by the competent authority until compliance with the permit conditions is restored.
Member States shall ensure that suspension measures referred to in paragraphs 3 and 4 and adopted by competent authorities in relation to an operator which infringes national provisions adopted pursuant to this Directive are enforced in an effective manner.
In the event of a breach of compliance affecting drinking water resources, including transboundary resources, or affecting waste water infrastructure in the case of an indirect discharge, the competent authority shall inform the drinking water and waste water operators, and all relevant authorities with a responsibility regarding compliance with the environmental legislation concerned, of the breach and the measures taken to prevent damage being caused, or remedy the damage caused, to human health and the environment.
in Article 9, paragraph 2 is replaced by the following:
‘2. For activities listed in Annex I to Directive 2003/87/EC, Member States may choose not to impose requirements laid down in Article 14(1), point (aa) and Article 15(4) of this Directive relating to energy efficiency in respect of combustion units or other units emitting carbon dioxide on the site.’
;
in Article 11, point (f) is amended as follows:
‘(f) energy is used efficiently and the use and, where possible, the production of renewable energy is promoted;’
;
in Article 11, the following points are inserted:
‘(fa) material resources and water are used efficiently, including through re-use;
an environmental management system is implemented as provided for in Article 14a.’
;
in Article 12, paragraph 1, points (b), (c) and (f) are replaced by the following:
‘(b) the raw and auxiliary materials, other substances, the energy and water used in or generated by the installation;
the sources of emissions from the installation, including odours;’
‘(f) the nature and quantities of foreseeable emissions, including odours, from the installation into each medium, as well as an identification of significant effects of the emissions on the environment;’
;
Article 13 is amended as follows:
paragraph 1 is replaced by the following:
‘1. In order to draw up, review and, where necessary, update BAT reference documents, the Commission shall organise an exchange of information between Member States, the industries concerned, non-governmental organisations promoting human health or environmental protection, the European Chemicals Agency and the Commission. That exchange of information shall aim at an eight-year review cycle of BAT reference documents prioritising the documents that have the highest potential to improve the protection of human health or the environment. The duration of the exchange of information referred to in the first subparagraph shall not exceed four years for each individual BAT reference document.’
;
the following paragraph is inserted:
‘1a. The Commission shall by 1 July 2026 amend Implementing Decision 2012/119/EU.’
;
in paragraph 2, the following subparagraph is added:
‘Without prejudice to Union competition law, information considered to be confidential business information or commercially sensitive information shall only be shared with the Commission and, after having signed a confidentiality and non-disclosure agreement, with civil servants and other public employees representing Member States or Union agencies. Information shall be anonymised, in such a manner that it does not refer to a particular operator or installation, when shared with the other stakeholders involved in the exchange of information referred to in paragraph 1. Non-anonymised information may only be shared in cases where anonymising the information would not allow an effective exchange of information on BAT in the context of drawing up, reviewing and, where necessary, updating BAT reference documents, with representatives of non-governmental organisations promoting the protection of human health or the environment and representatives of associations representing the relevant industrial sectors, as appropriate, and where such representatives of organisations and associations have signed a confidentiality and non-disclosure agreement. The exchange of information considered to be confidential business information or commercially sensitive information shall remain strictly limited to what is technically required to draw up, review and, where necessary, update BAT reference documents, and such confidential business information or commercially sensitive information shall not be used for other purposes.’
;
in paragraph 3, the first subparagraph is replaced by the following:
‘The Commission shall establish and regularly convene a forum composed of representatives of Member States, the industries concerned and non-governmental organisations promoting the protection of human health or the environment.’
;
in paragraph 3, the second subparagraph, point (d) is replaced by the following:
‘(d) guidance on the drawing up of BAT reference documents, and on their quality assurance including the suitability of their content and format.’
;
the following paragraph is inserted:
‘3a. The Commission shall obtain the opinion of the forum on the method for assessing compliance with emission limit values set out in the permit with regard to emissions to air and water, as set out in Article 15a.’
;
in paragraph 4, the following subparagraph is added:
‘The opinion of the forum referred to in the first subparagraph shall be submitted within six months of the final meeting of the technical working group responsible for that BAT reference document.’
;
paragraph 6 is replaced by the following:
‘6. After the adoption of a decision in accordance with paragraph 5, the Commission shall make the BAT conclusions and the BAT reference document publicly available without undue delay.’
;
Article 14 is amended as follows:
paragraph 1 is amended as follows:
the first subparagraph is replaced by the following:
‘Member States shall ensure that the permit includes all measures necessary to comply with the requirements of Articles 11 and 18. To that effect, Member States shall ensure that permits are granted further to consultation of all relevant authorities with a responsibility regarding compliance with Union environmental legislation, including with environmental quality standards.’
;
in the second subparagraph, point (a) is replaced by the following:
‘(a) emission limit values for polluting substances listed in Annex II to Regulation (EC) No 166/2006, and for other polluting substances, which are likely to be emitted from the installation concerned in significant quantities, having regard to their nature, their hazardousness and their potential to transfer pollution from one medium to another, taking into account the variation of water flow dynamics in receiving water bodies;’
;
in the second subparagraph, the following points are inserted:
‘(aa) environmental performance limit values in accordance with Article 15(4);
appropriate requirements ensuring the assessment of the need to prevent or reduce the emissions of substances fulfilling the criteria of Article 57 or substances addressed in restrictions in Annex XVII to regulation (EC) No 1907/2006;’
;
in the second subparagraph, point (b) is replaced by the following:
‘(b) appropriate requirements ensuring protection of the soil, groundwater, surface water and catchment areas for abstraction points of water intended for human consumption as referred to in Article 7 of Directive (EU) 2020/2184, and measures concerning the monitoring and management of waste generated by the installation;’
;
in the second subparagraph, the following points are inserted:
‘(ba) appropriate requirements laying down the characteristics of an environmental management system in accordance with Article 14a;
suitable monitoring requirements for the consumption and reuse of resources such as energy, water and raw materials;’
;
in the second subparagraph, point (d), the following point is added:
‘(iii) information on progress towards fulfilment of the environmental policy objectives referred to in Article 14a.;’
;
in the second subparagraph, point (e) is replaced by the following:
‘(e) appropriate requirements for the regular maintenance and surveillance of measures taken to prevent emissions to soil, surface and groundwater pursuant to point (b), and appropriate requirements concerning the periodic monitoring of soil, surface and groundwater in relation to relevant hazardous substances likely to be found on site and having regard to the possibility of soil, surface and groundwater contamination at the site of the installation.’
;
in the second subparagraph, point (h) is replaced by the following:
‘(h) conditions for assessing compliance with the emission limit values and environmental performance limit values or a reference to the applicable requirements specified elsewhere.’
;
the following article is inserted:
Member States shall require the operator to prepare and implement, for each installation falling within the scope of this Chapter, an environmental management system (“EMS”). The EMS shall include the elements listed in paragraph 2 and shall comply with relevant BAT conclusions that determine aspects to be covered in the EMS.
The EMS shall include at least the following:
environmental policy objectives for the continuous improvement of the environmental performance and safety of the installation, which shall include measures to:
prevent the generation of waste;
optimise resource and energy use and water reuse;
prevent or reduce the use or emissions of hazardous substances;
objectives and performance indicators in relation to significant environmental aspects, which shall take into account benchmarks set out in the relevant BAT conclusions;
for installations covered by the obligation to conduct an energy audit or implement an energy management system pursuant to Article 8 of Directive 2012/27/EU, inclusion of the results of that audit or implementation of the energy management system pursuant to Article 8 of and Annex VI to that Directive and of the measures to implement their recommendations;