EUPL Number | Metallic composition category (A) | Accepted metallic composition notation(s) | Accepted metallic composition constituents | Accepted metallic composition impurities | Relevant product groups | Conditions of use | Expiry date
Identity | Minimum concentration (% w/w) | Maximum concentration (% w/w) | Identity | Maximum concentration (% w/w)
1644 | Copper-Zinc alloys | CW501L-DW (CuZn10) |
Cu
Zn
89,0
Remainder
91,0 |
Fe
Ni
Pb
Sn
Each other impurity
0,05
0,2
0,05
0,1
< 0,02
C - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %.
31 December 2034
1645 | Copper-Zinc alloys | CW506L-DW (CuZn33) |
Cu
Zn
66,0
Remainder
68,0 |
Fe
Ni
Pb
Sn
Each other impurity
0,05
0,2
0,05
0,1
< 0,02
B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %.
31 December 2034
1646 | Copper-Zinc alloys | CW507L-DW (CuZn36) |
Cu
Zn
63,5
Remainder
65,5 |
Fe
Ni
Pb
Sn
Each other impurity
0,05
0,2
0,1
0,1
< 0,02
B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %.
31 December 2034
1647 | Copper-Zinc alloys | CW508L-DW (CuZn37) |
Cu
Zn
62,0
Remainder
64,0 |
Al
Fe
Ni
Pb
Sn
Each other impurity
0,05
0,1
0,2
0,1
0,1
< 0,02
B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %.
31 December 2034
1648 | Copper-Zinc alloys | CW509L-DW (CuZn40) |
Cu
Zn
59,5
Remainder
61,5 |
Al
Fe
Ni
Pb
Sn
Each other impurity
0,05
0,2
0,2
0,2
0,2
< 0,02
B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %;
Pb: ≤ 0,2 %.
31 December 2034
1649 | Copper-Zinc alloys | CW510L-DW (CuZn42) |
Cu
Zn
57,0
Remainder
59,0 |
Al
Fe
Ni
Pb
Sn
Each other impurity
0,05
0,3
0,2
0,2
0,3
< 0,02
B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %.
31 December 2034
1650 | Copper-Zinc-Aluminium alloys | CuZn42Al (CC773S) | Cu | 57,0 | 59,0 | Fe | 0,3 | B - D | | 31 December 2034
Zn | Remainder | | Pb | 0,2
Al | 0,1 | 0,3 |
Sn
Each other impurity
0,3
< 0,02
1651 | Copper-Zinc-Aluminium-Tin alloys | CuZn35Al1.5Sn | Cu | 64,0 | 66,0 | Fe | 0,10 | B - D | | 31 December 2034
Zn | Remainder | | Mn | 0,10
Al
Sn
1,40
0,50
1,60
0,70
Ni
Pb
Si
Each other impurity
0,10
0,2
0,2
< 0,02
1652 | Copper-Zinc-Aluminium-Silicon-Iron alloys | CuZn35AlSiFe | Cu | 62,5 | 64,5 | Ni | 0,09 | B - D | | 31 December 2034
Zn | Remainder | | Pb | 0,15
Al
Si
Fe
0,5
0,5
0,04
0,85
0,8
0,1
Sn
Each other impurity
0,1
< 0,02
1653 | Copper-Zinc-Arsenic alloys | CW707R (CuZn30As) | Cu | 69,0 | 71,0 | Fe | 0,05 | B - D | | 31 December 2034
Zn | Remainder | | Mn | 0,1
As | 0,02 | 0,06 |
Pb
Sn
Each other impurity
0,07
0,05
< 0,02
1654 | Copper-Zinc-Arsenic-Aluminium alloys | CuZn35Al-C | Cu | 63,0 | 64,5 | Fe | 0,3 | B - D | | 31 December 2034
Zn | Remainder | | Mn | 0,1
As
Al
0,04
0,2
0,14
0,7
Pb
Sn
Each other impurity
0,2
0,3
< 0,02
1655 | Copper-Zinc-Arsenic-Aluminium alloys | CW702R (CuZn20Al2As) | Cu | 76,0 | 79,0 | Pb | 0,05 | A - B | | 31 December 2034
Zn | Remainder | | Ni | 0,1
Al
As
1,8
0,02
2,3
0,06
Sb
Each other impurity
0,02
< 0,02
1656 | Copper-Zinc-Arsenic-Antimony-Aluminium alloys | CC771S (CuZn36AlAsSb-C) | Cu | 62,0 | 65,0 | Fe | 0,2 | B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %.
31 December 2034
Zn | Remainder | | Mn | 0,1
As
Sb
Αl
0,02
0,02
0,45
0,04
0,05
0,7
Ni
Pb
Sn
Each other impurity
0,20
0,2
0,3
< 0,02
1657 | Copper-Tin-Zinc-Phosphorus-Sulfur alloys | CuSn4Zn2PS |
Cu
Sn
Zn
P
S
90,0
3,0
1,0
0,01
0,2
96,0
5,0
3,0
0,1
0,6
Fe
Ni
Pb
Sb
Each other impurity
0,3
0,3
0,2
0,1
< 0,02
B - D | | 31 December 2034
1658 | Copper-Zinc-Silicon-Phosphorus alloys | CW724R (CuZn21Si3P) | Cu | 75,0 | 77,0 | Al | 0,05 | B - D | | 31 December 2034
Zn | Remainder | | Fe | 0,3
Si
P
2,7
0,02
3,5
0,10
Mn
Ni
Pb
Sn
Each other impurity
0,05
0,2
0,1
0,3
< 0,02
1659 | Copper-Zinc-Silicon-Phosphorus alloys | CC768S (CuZn21Si3P-C) | Cu | 75,0 | 77,0 | Al | 0,05 | B - D | B and Zr are used for grain refinement of this alloy. In the final material the content of these two elements shall be < 0,02 %. | 31 December 2034
Zn | Remainder | | Fe | 0,3
Si
P
2,7
0,02
3,5
0,10
Mn
Ni
Pb
Sn
Each other impurity
0,05
0,2
0,1
0,3
< 0,02
1660 | Copper-Silicon-Zinc-Manganese-Phosphorus alloys | CC245E (CuSi4Zn4MnP-C) | Cu | Remainder | | Al | 0,3 | B - D | | 31 December 2034
Si
Zn
Mn
P
2,5
1,0
0,03
0,05
4,5
7,0
0,09
0,15
Fe
Ni
Pb
Sn
Each other impurity
0,3
0,10
0,10
0,3
< 0,02
1661 | Copper-Silicon-Zinc-Manganese-Phosphorus alloys | CC246E (CuSi4Zn9MnP-C) | Cu | Remainder | | Al | 0,3 | B - D | | 31 December 2034
Si
Zn
Mn
P
2,5
7,0
0,03
0,05
4,5
11,0
0,09
0,15
Fe
Ni
Pb
Sn
Each other impurity
0,3
0,10
0,10
0,3
< 0,02
1662 | Copper-Silicon-Zinc-Manganese-Phosphorus alloys | CuSi4Zn4MnP | Cu | Remainder | | Al | 0,3 | B - D | | 31 December 2034
Si
Zn
Mn
P
2,5
1,0
0,01
0,05
4,5
7,0
0,09
0,15
Fe
Ni
Pb
Sn
Each other impurity
0,3
0,10
0,10
0,3
< 0,02
1663 | Copper-Silicon-Zinc-Manganese-Phosphorus alloys | CuSi4Zn9MnP | Cu | Remainder | | Al | 0,3 | B - D | | 31 December 2034
Si
Zn
Mn
P
2,5
7,0
0,01
0,05
4,5
11,0
0,09
0,15
Fe
Ni
Pb
Sn
Each other impurity
0,3
0,10
0,10
0,3
< 0,02
1664 | Copper-Tin-Phosphorus alloys | CW453K (CuSn8) | Cu | Remainder | | Fe | 0,1 | C - D | | 31 December 2034
Sn
P
7,5
0,02
8,5
0,4
Ni
Zn
Each other impurity
0,2
0,2
< 0,02
1665 | Copper-Tin-Lead-Phosphorus alloys | CuSn10-C |
Cu
Sn
Pb
P
88,0
9,0
0,2
0,01
90,0
11,0
1,0
0,2
Fe
Mn
Ni
S
Sb
Zn
Each other impurity
0,2
0,10
0,2
0,05
0,1
0,5
< 0,02
B - D |
Contents of certain elements are further restricted, compared to the standardised composition:
Ni: ≤ 0,2 %;
Sb: ≤ 0,1 %;
Pb: 0.2 % - 1.0 %;
P: 0.01 % - 0.2 %.
31 December 2034
1666 | Copper-Nickel-Manganese-Iron alloys | CW352 (CuNi10FeMn) | Cu | Remainder | | Each impurity | < 0,02 | B - D | For use exclusively for fittings and ancillaries for heat exchangers and desalination equipment. | 31 December 2031
Ni
Mn
Fe
9,0
0,5
1,0
11,0
1,0
2,0
1667 | Copper-Nickel-Manganese-Iron alloys |
CW352H (CuNi10Fe1Mn)
CW353H (CuNi30Fe2Mn2)
CW354H (CuNi30Mn1Fe)
Cu | Remainder | | Each impurity | < 0,02 | B | For use exclusively for fittings and ancillaries in desalination plants. | 31 December 2031
Ni
Fe
Mn
9,0
1,0
0,5
32,0
2,5
2,5
1668 | Coppers | CW024A (Cu-DHP) | Cu | 99,9 | | Each impurity | < 0,02 | A - D | Copper pipes cannot be used with all drinking waters distributed within the EU. Some water compositions (e.g., test water 1 according to EN 15664-1) cause a very high copper release. Member States may restrict the use of copper pipes with certain drinking waters. | 31 December 2034
P | 0,015 | 0,040
1669 | Coppers | CW004A (Cu-ETP) | Cu | 99,90 | | Each impurity | < 0,02 | C - D | | 31 December 2034
O | | 0,040
1670 | Coppers | CW008A (Cu-OF) | Cu | 99,95 | | Each impurity | < 0,02 | B - D | | 31 December 2034
1671 | Coppers | CW020A (Cu-PHC) | Cu | 99,95 | | Each impurity | < 0,02 | B - D | | 31 December 2034
P | 0,001 | 0,006
1672 | Coppers | CW021A (Cu-HCP) | Cu | 99,95 | | Each impurity | < 0,02 | B - D | | 31 December 2034
P | 0,002 | 0,007
1673 | Coppers | CW023A (Cu-DLP) | Cu | 99,90 | | Each impurity | < 0,02 | B - D | | 31 December 2034
P | 0,005 | 0,013
1674 | Tinned copper pipes and tinned copper fittings | CW024A (Cu-DHP) with a tin layer of 1 μm thickness | Sn | 90 | | Impurities of the tin layer | | A - D | | 31 December 2034
Cu | | 10
As
Bi
Cd
Cr
Ni
Pb
Sb
Each other impurity
0,01
0,01
0,01
0,01
0,01
0,01
0,01
< 0,02
1675 | Aluminium | Aluminium | Al | 99,0 | |
Fe+Si
Cu
Others (e.g., Cr, Mg, Mn, Ni, Zn)
Each other impurity
1,0
0,10 if Cr and/or Mn ≥ 0,05 %; 0,20 if Cr and/or Mn < 0,05 %
0,1 each
< 0,02
B - C |
For use in access ladders and other minor components, and not for long-term contact, as follows:
short contact: up to 24 hours at any temperature condition;
prolonged contact: more than 24 hours at a refrigerated temperature (8 - 12 °C).
31 December 2031
1676 | Steel/Iron | Galvanised steel | Zn coating | | | Impurities of the zinc coating | | A - D |
Acceptance is based on results that have been obtained with galvanised steel pipes with lead concentrations between 1,0 % and 0,6 % in the zinc layer, assuming a similar behaviour of pipes with lower lead concentrations.
Galvanised steel pipes cannot be used with all drinking waters distributed within the EU. Member States may restrict the use of galvanised steel pipes with certain drinking waters which may cause unacceptable levels of corrosion.
31 December 2034
As
Bi
Cd
Cr
Pb
Sb
Each other impurity
0,02
0,01
0,01
0,02
0,05
0,01
< 0,02
1677 | Steel/Iron | Carbon steel according to EN 10025 / EN 10213 / EN 10222 | Fe | | | Al | 0,05 |
Carbon steel with protective layer/coating: A - D.
Unprotected carbon steel: C2 - D
Carbon Steel for pipes and tanks: carbon steel without permanent protective layers (e.g., cementitious mortar linings or organic coatings (e.g. epoxy resins)) is not suitable for use in contact with drinking water.
Carbon Steel for ancillaries: unprotected carbon steel can be used for specific applications (e.g. pumps, valves) and only for small surface in contact with drinking water.
31 December 2034
C
Cr
Mo
Mn
Ni
0,02
0,02
0,02
0,02
0,02
0,25
0,30
0,12
1,65
0,50
Cu
Nb
P
S
Si
Ti
V
Each other impurity
0,55
0,05
0,03
0,03
0,6
0,05
0,12
< 0,02
1678 | Steel/Iron | Cast iron according to EN 1561 / EN 1563 | Fe | | | As | 0,05 | C2 |
Cast iron for pipes and tanks: cast iron without permanent protective layers is not suitable for pipes and fittings in contact with drinking water.
Cast iron for ancillaries: unprotected cast iron can be used for specific applications (e.g. pumps, valves) and only for very small surface in contact with drinking water.
31 December 2034
C
Cu
Cr
Mo
Mn
Ni
Si
0,02
0,02
0,02
0,02
0,02
0,02
1.5
4,0
1,0
1,0
1,0
1,0
1,0
3,5
Mg
P
S
Sn
V
Each other impurity
0,1
0,15
0,1
0,1
0,1
< 0,02
1679 | Steel/Iron | Stainless steels according to EN 10088 and EN 10283 | | | | | | A - D | | 31 December 2034
1680 | Platings | Electroplating of the outer surface (tin plating applied by a galvanic process) |
Cu
Sn
B- D (by reference to Cu alloys listed elsewhere in the metallic materials EUPL) |
Restrictions:
Bulk material of components to be tinned: copper alloys approved in the metallic materials EUPL;
Layer composition: (i) Cu (ii) Sn;
Applied process: galvanic tin plating;
Purity of the used anodes: ≥ 99,90 %.
31 December 2031
1681 | Platings | Tin/Nickel platings applied by a galvanic process on the external surface |
Sn
Ni
65
33
67
35
B- D (by reference to Cu alloys listed elsewhere in the metallic materials EUPL) |
Restrictions:
Bulk composition of components to be plated: copper alloys approved in the metallic materials EUPL;
composition of the plating: Sn (66 ± 1 %) and Ni (34 ± 1 %) (molar ratio 1:1);
applied process: galvanic plating;
purity of the used nickel-anodes: 99,90 %.
31 December 2031
1682 | Platings | Electrolytic Nickel/Chromium platings |
NI
Cr
B | | 31 December 2031
1683 | Passive compositions | NiCr7030 | Ni | 60,0 | | Al | 0,30 | B - D | | 31 December 2034
Cr
Si
29,0
0,50
32,0
2,0
C
Co
Cu
Fe
Mn
P
S
Each other impurity
0,10
1,5
0,50
5,0
1,00
0,020
0,015
< 0,02
1684 | Passive compositions | Ni55Ti45 |
Ni
Ti
54,0
Remainder
56,0 | Each impurity | < 0,02 | C - D | | 31 December 2034
1685 | Passive compositions | Ti1 according to ISO 23515:2022 | Ti | Remainder | |
C
O
N
H
Fe
Each other impurity
Other impurities in total
0,08
0,18
0,03
0,015
0,20
< 0,1
< 0,4
B - D | | 31 December 2034
1686 | Passive compositions | Ti2 according to ISO 23515:2022 | Ti | Remainder | |
C
O
N
H
Fe
Each other impurity
Other impurities in total
0,08
0,25
0,03
0,015
0,30
< 0,1
< 0,4
B - D | | 31 December 2034
1687 | Passive compositions | Ti3 according to ISO 23515:2022 | Ti | Remainder | |
C
O
N
H
Fe
Each other impurity
Other impurities in total
0,08
0,35
0,05
0,015
0,30
< 0,1
< 0,4
B - D | | 31 December 2034
1688 | Passive compositions | Ti4 according to ISO 23515:2022 | Ti | Remainder | |
C
O
N
H
Fe
Each other impurity
Other impurities in total
0,08
0,40
0,05
0,015
0,50
< 0,1
< 0,4
B - D | | 31 December 2034
1689 | Passive compositions | Ti-6Al-4V according to ISO 23515:2022 | Ti | Remainder | | C | 0,08 | B - D | | 31 December 2034
Al
V
5,5
3,5
6,75
4,5
O
N
H
Fe
Each other impurity
Other impurities in total
0,20
0,05
0,015
0,4
< 0,1
< 0,4
1690 | Passive compositions | Ti3.5Al3.0V0.4Mo0.9Ni0.25Pd0.14Ru0.2Fe | Ti | Remainder | | Total impurities | < 0,08 | B - D | | 31 December 2031
Al
V
Mo
Ni
Pd
Ru
Fe
3,5
3
0,4
0,9
0,25
0,14
0,2
EUPL Number | Metallic composition category (A) | Accepted metallic composition notation(s) | Accepted metallic composition constituents | Accepted metallic composition impurities | Relevant product groups | Conditions of use | Expiry date
Identity | Minimum concentration (% w/w) | Maximum concentration (% w/w) | Identity | Maximum concentration (% w/w)
1691 | Copper alloys not elsewhere categorised | Other copper alloys for Product Group D |
Cu
Zn
Si
P
Al
Fe
Mn
Pb
Ni
As
Sb
No restriction
No restriction
No restriction
No restriction
3,0
3,0
3,0
1,8
3,0
0,25
0,25
Each other element | 0,1 | D | | 31 December 2031
1692 | Passive compositions | Other passive metallic materials for Product Group D | | | | | | D | | 31 December 2031
1693 | Hard brazing alloys and soft soldering alloys | Hard brazing and soft soldering alloys meeting the maximum concentrations of the specified impurities | | | |
Pb
Sb
Cd
0,1
0,1
0,01
B - C
taking on account the extension of the final surface that might be exposed to drinking water
For capillary brazing/soldering of pipes and fittings.
The application of these alloys is critical to how they will behave during use and certain combinations of brazing/soft soldering alloy and parent metals may result in significant release of certain metals into the drinking water.
31 December 2031
The meaning of the note provided in Tables 1 and 2 is as follows:
A. Metallic composition category means a group of metallic compositions with the same metallic composition constituents, the same behaviour in contact with water intended for human consumption and the same restrictions with regard to water composition and/or surface area. A category has a reference material(s) with a controlled composition for which the metal releases are known and reproducible and represents the reasonable worst-case metal releases for the category. They are identified in the ECHA guidance.
The MTCtap, metallics, used to assess the safety of the use of the compositions listed under Tables 1 and 2 are provided for information purposes under Annex V.