2 Addendum to EC type-approval certificate No …, Regulation (EU) 2022/2383

In forcesince 6 Dec 2022

1.1. Particulars to be completed in relation to the type-approval of a vehicle with an approved engine installed:

1.1.1. Make of engine (name of undertaking):

1.1.2. Type and commercial description (mention any variants):

1.1.3. Manufacturer’s code as marked on the engine:

1.1.4. Category of vehicle (if applicable) (b):

1.1.5. Category of engine: Diesel/Petrol/LPG/NG-H/NG-L/NG-HL/Ethanol (ED95)/Ethanol (E85)/LNG/LNG20/B100 (1):

1.1.5.1. Type of dual-fuel engine: Type 1A/Type 1B/Type 2A/Type 2B/Type 3B (1)(d1):

1.1.6. Name and address of manufacturer:

1.1.7. Name and address of manufacturer’s authorised representative (if any):

1.2. If the engine referred to in 1.1 has been type approved as a separate technical unit:

1.2.1. Type-approval number of the engine/engine family (1):

1.2.2. Engine Control Unit (ECU) software calibration number:

1.3. Particulars to be completed in relation to the type-approval of an engine/engine family (1) as a separate technical unit (conditions to be respected in the installation of the engine on a vehicle):

1.3.1. Maximum and/or minimum intake depression:

1.3.2. Maximum allowable back pressure:

1.3.3. Exhaust system volume:

1.3.4. Restrictions of use (if any):

1.4. Emission levels of the engine/parent engine (1)

Deterioration Factor (DF): calculated/fixed (1)

Specify the DF values and the emissions on the WHSC (if applicable) and WHTC tests in the table below

1.4.1. WHSC test

WHSC test (if applicable) (10)(d5)

DF | CO | THC | NMHC (d4) | NOX | PM Mass | NH3 | PM Number

Mult/add (1) | | | | | | |

Emissions |

CO

(mg/kWh)

THC

(mg/kWh)

NMHC (d4)

(mg/kWh)

NOx

(mg/kWh)

PM Mass

(mg/kWh)

NH3

ppm

PM Number

(#/kWh)

Test result | | | | | | |

Calculated with DF | | | | | | |

CO2 mass emission: … g/kWh

Fuel consumption … g/kWh

1.4.2. WHTC test

WHTC test (10)(d5)

DF | CO | THC | NMHC (d4) | CH4 (d4) | NOx | PM Mass | NH3 | PM Number

Mult/add (1) | | | | | | | |

Emissions |

CO

(mg/kWh)

THC

(mg/kWh)

NMHC (d4)

(mg/kWh)

CH4 (d4)

(mg/kWh)

NOx

(mg/kWh)

PM Mass

(mg/kWh)

NH3

ppm

PM Number

(#/kWh)

Cold start | | | | | | | |

Hot start w/o regeneration | | | | | | | |

Hot start with regeneration (1) | | | | | | | |

kr,u (mult/add) (1) | | | | | | | |

kr,d (mult/add) (1)

Weighted test result | | | | | | | |

Final test result with DF | | | | | | | |

CO2 mass emission: … g/kWh

Fuel consumption: … g/kWh

1.4.3. Idle test

Test |

CO value

(% vol.)

Lambda (1) | Engine speed (min–1) | Engine oil temperature (°C)

Low idle test | | N/A | |

High idle test | | | |

1.4.4. PEMS demonstration test

Vehicle type (e.g. M3, N3 and application e.g. rigid or articulated truck, city bus) |

Vehicle description (e.g. vehicle model, prototype) |

Pass-fail results (7) | CO | THC | NMHC | CH4 | NOx | PM number

Work window conformity factor (11) | | | | | |

CO2 mass window conformity factor (11) | | | | | |

Trip information | Urban | Rural | Motorway

Shares of time of the trip characterised by urban, rural and motorway operation as described in point 4.5 of Annex II to Regulation (EU) No 582/2011 | | |

Shares of time of the trip characterised by accelerating, decelerating, cruising and stop as described in point 4.5.5 of Annex II to Regulation (EU) No 582/2011 | | |

Minimum | Maximum

Work window average power (%) | |

CO2 mass window duration (s) | |

Work window: percentage of valid windows |

CO2 mass window: percentage of valid windows |

Fuel consumption consistency ratio |

1.5 Power measurement

1.5.1. Engine power measured on test bench

Measured engine speed (rpm) | | | | | | |

Measured fuel flow (g/h) | | | | | | |

Measured torque (Nm) | | | | | | |

Measured power (kW) | | | | | | |

Barometric pressure (kPa) | | | | | | |

Water vapour pressure (kPa) | | | | | | |

Intake air temperature (K) | | | | | | |

Power correction factor | | | | | | |

Corrected power (kW) | | | | | | |

Auxiliary power (kW) (1) | | | | | | |

Net power (kW) | | | | | | |

Net torque (Nm) | | | | | | |

Corrected specific fuel consumption (g/kWh) | | | | | | |

1.5.2. Additional data, e.g. the power correction factor for each fuel declared (if applicable)