1 ANNEX, Regulation (EU) 2022/2383

In forcesince 6 Dec 2022
(1)

Annex I to Regulation (EU) No 582/2011 is amended as follows:

(a)

in point 1.1.2 the introductory sentence is replaced by the following:

‘If the manufacturer permits the engine family to run on market fuels that do not comply either with Directive 98/70/EC of the European Parliament and of the Council [Directive 98/70/EC of the European Parliament and of the Council of 13 October 1998 relating to the quality of petrol and diesel fuels and amending Council Directive 93/12/EEC (OJ L 350, 28.12.1998, p. 58).’;], or with CEN standard EN 228:2012 in the case of unleaded petrol or CEN standard EN 590:2013 in the case of diesel or CEN standard EN 14214:2012+A2:2019 in the case of FAME B100, such as paraffinic fuel (CEN standard EN 15940) or others, the manufacturer shall, in addition to the requirements in point 1.1.1, comply with the following requirements:

(b)

after point 1.3 the following point is added:

1.4.1. The type-approval of a B100 family with a parent engine tested on FAME B100 shall be extended to all family members and biodiesel blends with a FAME content that exceeds that of FAME B30 (CEN standard EN 16709), without further testing. The type-approval may be extended to biodiesel blends with a lower FAME content, if the requirements of this regulation are also satisfied for these blends without making any adjustments to the vehicle. In such a case the manufacturer shall declare the biodiesel blends the engine family is capable of running on in point 3.2.2.2.1 of the Information Document as set out in Part 1 of Appendix 4. If the approval authority determines that the submitted application is not fully representative, biodiesel blends other than FAME B100 may be selected by the approval authority and tested.’;

(c)

the following point 3.2.1.7 is inserted:

‘3.2.1.7. In the case of a B100 type-approval, the approval mark shall contain ‘B100’ after the national symbol.’;

(d)

in Appendix 4 PART 1 point 3.2.2.2 is replaced by the following:

‘3.2.2.2. Heavy duty vehicles Diesel/Petrol/LPG/NG-H/NG-L/NG-HL/Ethanol (ED95)/Ethanol (E85)/LNG/LNG20/B100 (1) (6)’;

(e)

in the Addendum to Appendix 5 point 1.1.5 is replaced by the following:

‘1.1.5. Category of engine: Diesel/Petrol/LPG/NG-H/NG-L/NG-HL/Ethanol (ED95)/Ethanol (E85)/LNG/LNG20/B100 (1)’;

(f)

point 8 of Appendix 6 is replaced by the following:

‘8. Signature:

Attachment: Information package.

Test report.

Addendum’;

(g)

the following Addendum is added to Appendix 6:

‘’;

(h)

in the Addendum to Appendix 7 point 1.1.5 is replaced by the following:

‘1.1.5. Category of engine: Diesel/Petrol/LPG/NG-H/NG-L/NG-HL/Ethanol (ED95)/Ethanol (E85)/LNG/LNG20/B100 (1)’;

(2)

in Annex II, point 4.4.2, the following sentence is added:

‘In the case of a B100 type-approval, approval authorities may request to test the vehicle on biodiesel with any FAME content.’;

(3)

in Annex IX, under the heading ‘Technical data on fuels for testing compression ignition and dual-fuel engines’, the following table is inserted after the table ‘Type: Diesel (B7)’:

‘Type: pure Biodiesel (B100) for compression ignition engines

[If CFPP is – 20 °C or lower, the viscosity shall be measured at – 20 °C. The measured value shall not exceed 48 mm2/s. In this case, the standard test methods are applicable without the precision data owing to non-Newtonian behaviour in a two-phase system.] [A 2 ml sample and apparatus equipped with a thermal detection device shall be used.] [The determination of derived cetane number for FAME is not included in the precision determinations of some test methods.’]

Parameter | Unit | Limits | Test method

Minimum | Maximum

FAME content | % (m/m) | 96,5 | – | EN 14103

Density at 15 °C | kg/m3 | 860 | 900 |

EN ISO 3675

EN ISO 12185

Viscosity at 40 °C | mm2/s | 3,50 | 5,00 |

EN ISO 3104

EN 16896

Flash point | °C | 101 | – |

EN ISO 2719

EN ISO 3679

Cetane number | – | 51,0 | – |

EN ISO 5165

EN 15195

EN 16715

EN 17155

Copper strip corrosion (3 h at 50 °C) | Rating | class 1 | EN ISO 2160

Oxidation stability (at 110 °C) | h | 8,0 | – |

EN 14112

EN 15751

Acid value | mg KOH/g | – | 0,50 | EN 14104

Iodine value | g iodine/100 g | – | 120 |

EN 14111

EN 16300

Linolenic acid methyl ester | % (m/m) | – | 12,0 | EN 14103

Polyunsaturated (≥ 4 double bonds) methyl esters | % (m/m) | – | 1,00 | EN 15779

Methanol content | % (m/m) | – | 0,20 | EN 14110

Monoglyceride content | % (m/m) | – | 0,70 | EN 14105

Diglyceride content | % (m/m) | – | 0,20 | EN 14105

Triglyceride content | % (m/m) | – | 0,20 | EN 14105

Free glycerol | % (m/m) | – | 0,02 |

EN 14105

EN 14106

Total glycerol | % (m/m) | – | 0,25 | EN 14105

Water content | % (m/m) | – | 0,050 | EN ISO 12937

Total contamination | mg/kg | – | 24 | EN 12662

Sulphated ash content | % (m/m) | – | 0,02 | ISO 3987

Sulphur content | mg/kg | – | 10,0 |

EN ISO 20846

EN ISO 20884

EN ISO 13032

Group I metals (Na+K) | mg/kg | – | 5,0 |

EN 14108

EN 14109

EN 14538

Group II metals (Ca+Mg) | mg/kg | – | 5,0 | EN 14538

Phosphorus content | mg/kg | – | 4,0 |

EN 14107

EN 16294