6 Appendix 3 Wheelchair-accessible vehicles, Regulation (EU) 2022/2236

In forcesince 20 Jun 2022

Item | Subject | Regulatory act | M1

A | RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY

A1 | Interior fittings | Regulation (EU) 2019/2144 |

G

Note G may be applied to those fittings in the interior of the vehicle that are not significantly affected by the modification, however, any added or modified fittings in the interior shall comply with the requirements as applicable for vehicle category M1

Application is limited to the passenger compartment in front of the transverse plane passing through the torso reference line of the 3-D H-point machine placed on the rearmost seat designated for normal use when the vehicle is used on a public road, as well as to the respective reference zones of each seating position designated for normal use as defined in the regulatory act when the vehicle type is subject to the requirements applicable to vehicle category M1.

A2 | Seats and head restraints | Regulation (EU) 2019/2144 |

G

Note G may be applied to seats and head restraints of the vehicle that are not significantly affected by the modification, however, any added or modified fittings concerning seats and head restraints shall comply with the requirements as applicable for vehicle category M1

The energy dissipation and radii requirements of seats and head restraints are checked in accordance with paragraphs 5.2.3/5.2.4.2. and 5.2.4. of UN Regulation No 17 when the vehicle type is subject to the requirements applicable to vehicle category M1.

The longitudinal plane of the intended wheelchair-travelling position shall be parallel to the longitudinal plane of the vehicle.

Appropriate information is to be made available to the vehicle owner that, in order to withstand the forces transmitted by the tie-down mechanism during the various driving conditions, a wheelchair with a structure meeting the relevant part of ISO 7176-19:2008/Amd 1:2015 (or later revisions) is recommended.

The seats of the vehicle may be adapted without further testing, provided it can be demonstrated to the satisfaction of the technical service that their anchorages, mechanisms and head restraints provide an adequate level of performance.

The luggage retention requirements of UN Regulation No 17 (para. 1, point (c) and Annex 9) do not apply.

A3 | Bus seats | Regulation (EU) 2019/2144 | not in scope

A4 | Safety-belt anchorages | Regulation (EU) 2019/2144 |

X

Each wheelchair location shall be provided with anchorages to which a wheelchair tie-down and occupant restraint system (WTORS) is to be fitted, and that complies with the additional provisions for testing the wheelchair tie down and occupant restraint system set out below.

1.

Definitions

1.1. Surrogate wheelchair (SWC) means a rigid, re-usable test wheelchair, as defined in Section 3 of international standard ISO 10542-1:2012.

1.2. Point P means a representation of the position of the wheelchair occupant’s hip when seated in the SWC, as defined in Section 3 of international standard ISO 10542-1:2012. At the request of the manufacturer, a heavier surrogate wheelchair may be used, provided it has the same dimensional characteristics and centre of gravity position as the prescribed version. The pneumatic tyres may be replaced with solid or foam-filled versions in the same size.

1.3. WTORS means a wheelchair tie-down and occupant restraint system.

2.

General requirements

2.1. Each wheelchair location shall be provided with anchorages to which a WTORS can be fitted.

2.2. The wheelchair occupant’s lower belt anchorages shall be located in accordance with paragraph 5.4.2.2 UN Regulation No 14, relative to Point P on the SWC, when placed in the travelling position designated by the manufacturer. The upper actual anchorage(s) shall be located at least 1100 mm above the horizontal plane passing through the points of contact between the rear tyres of the SWC and the vehicle floor. That condition shall still be satisfied after the test carried out in accordance with points 3 or 4 below.

Either point 3 or 4 shall apply.

3.

Static in-vehicle testing

3.1. Wheelchair occupant restraint anchorages

3.1.1. The wheelchair occupant restraint anchorages shall resist the static forces prescribed for occupant restraint anchorages in UN Regulation No 14, simultaneously with the static forces applied to the wheelchair tie-down anchorages as specified in point 3.2.

3.2. Wheelchair tie-down anchorages

The wheelchair tie-down anchorages shall resist the following forces, for at least 0,2 seconds, applied via the SWC (or a suitable surrogate wheelchair having a wheelbase, seat height and tie-down attachment points in accordance with the specification for the SWC), at a height of 300 +/– 100 mm from the surface on which the SWC rests:

3.2.1. In the case of a forward-facing wheelchair, a simultaneous force, coinciding with the force applied to the occupant restraint anchorages, of 24,5 kN; and

3.2.2. a second test applying a static force of 8,2 kN directed towards the rear of the vehicle.

3.2.3. In the case of a rearward-facing wheelchair, a simultaneous force, coincident with the force applied to the occupant restraint anchorages, of 8,2 kN, and

3.2.4. a second test applying a static force of 24,5 kN directed towards the front of the vehicle

4.

Dynamic in-vehicle testing

4.1. The full assembly of the WTORS system shall be tested by an in-vehicle dynamic test in accordance with points 5.2.2 and 5.2.3 and Annex A to international standard ISO 10542-1:2012, testing all components/anchorages simultaneously, using a vehicle body-in-white or representative structure.

A5 | Safety-belts and restraint systems | Regulation (EU) 2019/2144 |

X

Each wheelchair location is to be provided with an occupant restraint belt that complies with the additional provisions for testing the wheelchair tie down and occupant restraint system of set out below.

When, due to the conversion, anchorage points for the safety belts need to be moved outside the tolerance provided for in paragraph 7.7.1 of UN Regulation No 16, the technical service shall check whether the alteration constitutes a worst-case or not. If that is the case, the test provided for in paragraph 7.7.1 of UN Regulation No 16 shall be performed. The test may be performed using components that have not undergone the conditioning test prescribed by UN Regulation No 16.

1.

Definitions

1.1. Surrogate wheelchair (SWC) means a rigid, re-usable test wheelchair, as defined in Section 3 of international standard ISO 10542-1:2012.

1.2. Point P means a representation of the position of the wheelchair occupant’s hip when seated in the SWC, as defined in Section 3 of international standard ISO 10542-1:2012. At the request of the manufacturer, a heavier surrogate wheelchair may be used, provided it has the same dimensional characteristics and centre of gravity position as the prescribed version. The pneumatic tyres may be replaced with solid or foam-filled versions in the same size.

1.3. WTORS means a wheelchair tie-down and occupant restraint system.

2.

General requirements

2.1. An assessment shall be made of the WTORS occupant belt to ensure compliance with paragraphs 8.2.2 to 8.2.2.4 and 8.3.1 to 8.3.4 of UN Regulation No 16.

Either point 3. or 4. shall apply.

3.

Static in-vehicle testing

3.1. Components of the system

3.1.1. Where the WTORS anchorages have been tested statically in the vehicle, all components of the WTORS shall meet the relevant requirements of international standard ISO 10542-1:2012. However, the dynamic test specified in Annex A to, and points 5.2.2. and 5.2.3. of, international standard ISO 10542-1:2012 shall be carried out on the complete WTORS using the vehicle anchorage geometry instead of the test geometry specified in Annex A to international standard ISO 10542-1:2012. This may be carried out within the vehicle structure or on a surrogate structure representative of the vehicle’s WTORS anchorage geometry. The location of each anchorage used for the test shall lie within the tolerance provided for in paragraph 7.7.1 of UN Regulation No 16, of its true position relative to Point P.

3.1.2. Where the occupant restraint part of the WTORS is approved in accordance with UN Regulation No 16, it shall be subject to the dynamic test as part of the complete WTORS specified in point 3.1.1., however, the requirements of points 5.1, 5.3 and 5.4 of international standard ISO10542-1:2012 shall be considered to have been met.

4.

Dynamic in-vehicle testing

4.1. Where the WTORS anchorages have been tested dynamically in the vehicle, the component parts of the WTORS shall meet the relevant requirements of international standard ISO 10542-1:2012, points 5.1, 5.3 and 5.4. These requirements shall be deemed to have been met in respect of the occupant restraint if it is approved in accordance with UN Regulation No 16.

A6 | Safety-belt reminders | Regulation (EU) 2019/2144 | n/a

A7 | Partitioning systems | Regulation (EU) 2019/2144 | equipment

A8 | Child restraint anchorages | Regulation (EU) 2019/2144 |

IF

The minimum number of ISOFIX child seat anchorages need not to be provided. In the case of a multi-stage type approval where an ISOFIX anchorage system has been affected by the conversion, either the system shall be re-tested or the anchorages shall be rendered unusable. In the latter case the ISOFIX labels shall be removed and appropriate information shall be provided in the vehicle owner’s manual for the completed vehicle.

A9 | Child restraint systems (IF) | Regulation (EU) 2019/2144 | equipment

A10 | Enhanced child restraint systems (IF) | Regulation (EU) 2019/2144 | equipment

A11 | Front underrun protection | Regulation (EU) 2019/2144 | not in scope

A12 | Rear underrun protection | Regulation (EU) 2019/2144 | X

A13 | Lateral protection | Regulation (EU) 2019/2144 | not in scope

A14 | Fuel tank safety (IF) | Regulation (EU) 2019/2144 |

X

Modification of the routing, length of the refuelling duct, fuel hoses and fuel vapour pipes as well as re-positioning of the original tank and evaporative control devices provided by the manufacturer of the base vehicle is permissible without further testing provided the installation requirements of paragraphs 5.4, 5.5, 5.6, 5.7, 5.8, and 5.11 of UN Regulation No 34 are met, and provided that the technical service is satisfied, by visual inspection, that the essential requirements of paragraph 5.10 of that Regulation have been satisfied. In cases involving re-positioning of the original plastic tank, further testing in accordance with Annex 5 to UN Regulation No 34 is not required.

A15 | Liquified petroleum gas safety (IF) | Regulation (EU) 2019/2144 | G

A16 | Compressed and liquified natural gas safety (IF) | Regulation (EU) 2019/2144 | G

A17 | Hydrogen safety (IF) | Regulation (EU) 2019/2144 | G

A18 | Hydrogen system material qualification (IF) | Regulation (EU) 2019/2144 | X

A19 | In-use electric safety (IF) | Regulation (EU) 2019/2144 | G

A20 | Frontal off-set impact | Regulation (EU) 2019/2144 |

G

Alternatively, a suitable torsion stiffness test, in which a torque is applied to the vehicle as close as practicable to the spring mounting points, with all doors, hatches and bonnet opened, shall demonstrate that the torsional stiffness is within ± 75 % of that of the unmodified previous-stage vehicle body. In addition, a bending stiffness test shall be carried out with the vehicle on level ground, in which all side and rear doors and hatches shall open normally when the vehicle is loaded to its technically maximum permissible laden mass.

A21 | Frontal full-width impact | Regulation (EU) 2019/2144 |

G

Alternatively, a suitable torsion stiffness test, in which a torque is applied to the vehicle as close as practicable to the spring mounting points, with all doors, hatches and bonnet opened, shall demonstrate that the torsional stiffness is within ± 75 % of that of the unmodified previous-stage vehicle body. In addition, a bending stiffness test shall be carried out with the vehicle on level ground, in which all side and rear doors and hatches shall open normally when the vehicle is loaded to its technically maximum permissible laden mass.

A22 | Protective steering | Regulation (EU) 2019/2144 |

G

n/a in case of modified steering systems for drivers with special needs

A23 | Replacement airbag | Regulation (EU) 2019/2144 | equipment

A24 | Cab impact | Regulation (EU) 2019/2144 | not in scope

A25 | Side impact | Regulation (EU) 2019/2144 |

G

Alternatively, a suitable torsion stiffness test, in which a torque is applied to the vehicle as close as practicable to the spring mounting points, with all doors, hatches and bonnet opened, shall demonstrate that the torsional stiffness is within ± 75 % of that of the unmodified previous-stage vehicle body. In addition, a bending stiffness test shall be carried out with the vehicle on level ground, in which all side and rear doors and hatches shall open normally when the vehicle is loaded to its technically maximum permissible laden mass.

A26 | Pole side impact | Regulation (EU) 2019/2144 | n/a

A27 | Rear impact | Regulation (EU) 2019/2144 | n/a

A28 | 112-based eCall in-vehicles systems | Regulation (EU) 2015/758 | G

B | VULNERABLE ROAD USERS, VISION AND VISIBILITY

B1 | Pedestrian leg and head protection | Regulation (EU) 2019/2144 | G

B2 | Enlarged head impact zone | Regulation (EU) 2019/2144 |

G

Modifications to the interior fittings directly behind the windscreen do not have to be taken into account.

B3 | Frontal protection system | Regulation (EU) 2019/2144 | equipment

B4 | Advanced emergency braking for pedestrians and cyclists ahead | Regulation (EU) 2019/2144 |

G

n/a in case of modified braking systems for drivers with special needs

B5 | Pedestrian and cyclist collision warning | Regulation (EU) 2019/2144 | not in scope

B6 | Blind spot information system | Regulation (EU) 2019/2144 | not in scope

B7 | Reversing detection | Regulation (EU) 2019/2144 |

A

May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements

B8 | Forward vision | Regulation (EU) 2019/2144 | G

B9 | Heavy-duty vehicles direct vision | Regulation (EU) 2019/2144 | not in scope

B10 | Safety glazing | Regulation (EU) 2019/2144 | G

B11 | Defrost/demist | Regulation (EU) 2019/2144 | G

B12 | Wash/wipe | Regulation (EU) 2019/2144 | G

B13 | Indirect vision devices | Regulation (EU) 2019/2144 | X

B14 | Acoustic Vehicle Alerting Systems | Regulation (EU) No 540/2014 | X

C | VEHICLE CHASSIS, BRAKING, TYRES AND STEERING |

C1 | Steering equipment | Regulation (EU) 2019/2144 | G

C2 | Lane departure warning | Regulation (EU) 2019/2144 | not in scope

C3 | Emergency lane keeping | Regulation (EU) 2019/2144 |

G

n/a in case of modified steering systems for drivers with special needs, or in case of modified braking system if the ELKS of the base vehicle acts on the braking system instead.

C4 | Braking | Regulation (EU) 2019/2144 | G

C5 | Replacement braking parts | Regulation (EU) 2019/2144 | equipment

C6 | Brake assist | Regulation (EU) 2019/2144 |

G

n/a in case of modified braking systems for drivers with special needs

C7 | Stability control | Regulation (EU) 2019/2144 |

G

In case of modifications to the stability control system included as part of a previous stage type-approval, which are likely to affect the function of that base vehicle’s stability control system, it shall be demonstrated that the vehicle has not been rendered unsafe or unstable. This shall be proven by tests e.g. performing rapid double lane-change manoeuvres in each direction at 80 km/h with sufficient severity to cause intervention by the stability control system. These interventions shall be well-controlled and shall improve the stability of the vehicle under those driving conditions in comparison to the stability of the vehicle with, where practicable, a disabled stability control system. All tests are subject to the agreement between the manufacturer and technical service.

C8 | Advanced emergency braking on heavy-duty vehicles | Regulation (EU) 2019/2144 | not in scope

C9 | Advanced emergency braking on light-duty vehicles | Regulation (EU) 2019/2144 |

G

n/a in case of modified braking systems for drivers with special needs

C10 | Tyre safety and environmental performance | Regulation (EU) 2019/2144 | X

C11 | Spare wheels and run-flat systems (IF) | Regulation (EU) 2019/2144 | X

C12 | Retreaded tyres | Regulation (EU) 2019/2144 | equipment

C13 | Tyre pressure monitoring for light-duty vehicles | Regulation (EU) 2019/2144 | G

C14 | Tyre pressure monitoring for heavy-duty vehicles | Regulation (EU) 2019/2144 | not in scope

C15 | Tyre installation | Regulation (EU) 2019/2144 | X

C16 | Replacement wheels | Regulation (EU) 2019/2144 | equipment

D | ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS

D1 | Audible warning | Regulation (EU) 2019/2144 | X

D2 | Radio interference (electromagnetic compatibility) | Regulation (EU) 2019/2144 | X

D3 | Protection against unauthorised use, immobiliser and alarm systems | Regulation (EU) 2019/2144 | X

D4 | Protection of vehicle against cyberattacks | Regulation (EU) 2019/2144 | X

D5 | Speedometer | Regulation (EU) 2019/2144 | X

D6 | Odometer | Regulation (EU) 2019/2144 | X

D7 | Speed limitation devices | Regulation (EU) 2019/2144 | not in scope

D8 | Intelligent speed assistance | Regulation (EU) 2019/2144 |

A

May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements

D9 | Identification of controls, tell-tales and indicators | Regulation (EU) 2019/2144 | X

D10 | Heating systems | Regulation (EU) 2019/2144 | X

D11 | Light signalling devices | Regulation (EU) 2019/2144 | X

D12 | Road illumination devices | Regulation (EU) 2019/2144 | X

D13 | Retro-reflective devices | Regulation (EU) 2019/2144 | X

D14 | Light sources | Regulation (EU) 2019/2144 | X

D15 | Installation of light signalling, road illumination and retro-reflective devices | Regulation (EU) 2019/2144 | X

D16 | Emergency stop signal | Regulation (EU) 2019/2144 |

X

Only for vehicles fitted with electronically controlled anti-lock braking system

D17 | Headlamp cleaners (IF) | Regulation (EU) 2019/2144 | IF

D18 | Gear shift indicator | Regulation (EU) 2019/2144 | G

E | DRIVER AND SYSTEM BEHAVIOUR

E1 | Alcohol interlock installation facilitation | Regulation (EU) 2019/2144 | A

E2 | Driver drowsiness and attention warning | Regulation (EU) 2019/2144 |

A

May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements

E3 | Advanced driver distraction warning | Regulation (EU) 2019/2144 | No requirement yet

E4 | Driver availability monitoring system (in case of automated vehicles) | Regulation (EU) 2019/2144 | IF

E5 | Event data recorder | Regulation (EU) 2019/2144 |

A

May be partly exempted if equipment for special needs passengers prevents full compliance with the requirements and may be fully exempted if it is impossible to meet these requirements

E6 | Systems to replace driver’s control (in case of automated vehicles) | Regulation (EU) 2019/2144 | IF

E7 | Systems to provide the vehicle with information on state of vehicle and surrounding area (in case of automated vehicles) | Regulation (EU) 2019/2144 | IF

E8 | Platooning (IF) | Regulation (EU) 2019/2144 | No requirement yet

E9 | Systems to provide safety information to other road users (in case of automated vehicles) | Regulation (EU) 2019/2144 | No requirement yet

F | GENERAL VEHICLE CONSTRUCTION AND FEATURES

F1 | Registration plate space | Regulation (EU) 2019/2144 | X

F2 | Reversing motion | Regulation (EU) 2019/2144 | X

F3 | Door latches and hinges | Regulation (EU) 2019/2144 | X

F4 | Door entry steps, handholds and running boards | Regulation (EU) 2019/2144 | X

F5 | External projections | Regulation (EU) 2019/2144 |

G

Any boarding aids are considered only in the stowed position

F6 | External projections of commercial vehicle cabs | Regulation (EU) 2019/2144 | not in scope

F7 | Statutory plate and vehicle identification number | Regulation (EU) 2019/2144 | X

F8 | Towing devices | Regulation (EU) 2019/2144 |

X

Required for the front only, to be tested if fitted at the rear

F9 | Wheel guards | Regulation (EU) 2019/2144 | G

F10 | Spray suppression systems | Regulation (EU) 2019/2144 | not in scope

F11 | Masses and dimensions | Regulation (EU) 2019/2144 |

X

For the purposes of calculations, the mass of the wheel-chair including the user is assumed to be 160 kg. The mass is concentrated at the P point of the surrogate wheelchair in its travelling position as declared by the manufacturer.

It is permitted to temporarily limit the overall passenger capacity and to restrict the use of normal seating positions as a result of the actual transport of wheelchairs, with their users. In such case, the affected normal seating positions shall be clearly and permanently identified to users, either by means of a pictogram or a sign with an appropriate text. This shall be noted in Part 2 of the EU type-approval certificate as well as under “remarks” in the Certificate of Conformity as to allow inclusion of this information in on-board vehicle registration papers. In addition, the following shall be explained in the owner’s manual for the completed vehicle: The meaning of any pictograms used to mark the affected seating positions, as well as a more detailed description of the specific restrictions, if necessary.

F12 | Mechanical couplings | Regulation (EU) 2019/2144 | IF X

F13 | Vehicles intended for the transportation of dangerous goods (IF) | Regulation (EU) 2019/2144 | not in scope

F14 | General bus construction | Regulation (EU) 2019/2144 | not in scope

F15 | Bus strength of superstructure | Regulation (EU) 2019/2144 | not in scope

F16 | Flammability in buses | Regulation (EU) 2019/2144 | not in scope

G | ENVIRONMENTAL PERFORMANCE AND EMISSIONS

G1 | Sound level | Regulation (EU) No 540/2014 |

G

Modification of the exhaust system length is permitted without the need for retesting, provided that the exhaust back pressure remains similar.

G2 | Tailpipe emissions of vehicle in lab | Regulation (EC) No 715/2007 |

G

Modification in the exhaust system is permitted without any further test of tailpipe emissions provided that the emission control devices, including particulate filters (if any), are not affected.

This article is long: the rest is at the official publication.