The requirements laid down in Table 1 for “Small series scheme I” apply provided that:
the vehicle type is not based on or derived from a vehicle produced in large series, including those for EU or third markets; and
the manufacturer’s combined number of units, of all its categories M and N vehicle types registered, made available on the market or entered into service annually in the Union does not exceed 1500.
In all other cases, the requirements laid down in Table 1 for “Small series scheme II” and in Table 2 apply.
X
Full application of the regulatory act as follows:
a type-approval certificate shall be required;
tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 67 to 81;
the test report shall be drafted in accordance with Annex III;
Conformity of Production shall be ensured.
A
Application of the regulatory act as follows:
all requirements of the regulatory act shall be fulfilled unless otherwise stated;
a type-approval certificate is not required;
tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 67 to 81;
the test report shall be drafted in accordance with Annex III;
Conformity of Production shall be ensured.
B
Application of the regulatory act as follows:
Same as for explanatory note “A” with the exception that the tests and checks may be performed by the manufacturer themselves, subject to the agreement of the approval authority.
C
Application of the regulatory act as follows:
the technical requirements from the regulatory act shall be fulfilled, but with different transitional provision;
a type-approval certificate is not required;
tests and checks shall be conducted by the technical service or the manufacturer under the conditions laid down in Articles 67 to 81;
the test report shall be drafted in accordance with Annex III;
Conformity of Production shall be ensured.
IFSystems, separate technical units or components shall meet the requirements if fitted to the vehicle
n/aNot applicable
The specific provisions set out in Table 1 and Table 2 cannot be mixed or combined.
Small series scheme I | Small series scheme II
Item | Subject | Regulatory act | M1 | N1 | M1 | N1
A | RESTRAINT SYSTEMS, CRASH TESTING, FUEL SYSTEM INTEGRITY AND HIGH VOLTAGE ELECTRICAL SAFETY
A1 | Interior fittings | Regulation (EU) 2019/2144 |
B
Interior arrangement
Radii and protrusion requirements for switches, pull-knobs and the like, controls and general interior fittings. The requirements of paragraphs 5.1 to 5.6 of UN Regulation No 21 may be waived at the request of the manufacturer.
The requirements of paragraph 5.2 of UN Regulation No 21 with the exception of paragraphs 5.2.3.1, 5.2.3.2 and 5.2.4 of that Regulation shall apply.
Energy absorption tests on the upper dashboard. Energy absorption tests on the upper dashboard shall only be performed when the vehicle is not fitted with at least two front airbags or two static four-point harnesses.
Energy absorption test on the rear part of the seats: not applicable
Power-operation of windows, roof-panel systems and partition systems. All requirements of paragraph 5.8 of UN Regulation No 21 shall apply.
not in scope | B | not in scope
A2 | Seats and head restraints | Regulation (EU) 2019/2144 |
B
General requirements
Specifications Requirements of paragraph 5.2 of UN Regulation No 17 shall apply with the exception of paragraph 5.2.3 of that Regulation.
Strength tests for seat backrest and head restraints. The requirements of paragraph 6.2 of UN Regulation No 17 shall apply.
Unlocking and adjustment tests. The test shall be performed in accordance with the requirements of Annex 7 to UN Regulation No 17.
Head restraints
Specifications. Requirements of paragraphs 5.4, 5.5, 5.6, 5.10, 5.11 and 5.12 of UN Regulation No 17 shall apply with the exception of paragraph 5.5.2 of that Regulation.
Strength tests on head restraints. The test prescribed in paragraph 6.4 of UN Regulation No 17 shall be performed.
Special requirements regarding the protection of occupants from displaced luggage. The requirements of Annex 9 to UN Regulation No 17 may be waived at the request of the manufacturer.
B | B | B
A3 | Bus seats | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
A4 | Safety-belt anchorages | Regulation (EU) 2019/2144 | B | B | B | B
A5 | Safety-belts and restraint systems | Regulation (EU) 2019/2144 |
Components X
Installation requirements B
Components X
Installation requirements B
Components X
Installation requirements B
Components X
Installation requirements B
A6 | Safety-belt reminders | Regulation (EU) 2019/2144 | B | B | B | B
A7 | Partitioning systems | Regulation (EU) 2019/2144 | equipment | equipment | equipment | equipment
A8 | Child restraint anchorages | Regulation (EU) 2019/2144 | B | IF B | B | IF B
A9 | Child restraint systems (IF) | Regulation (EU) 2019/2144 | X | X | X | X
A10 | Enhanced child restraint systems (IF) | Regulation (EU) 2019/2144 | X | X | X | X
A11 | Front underrun protection | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
A12 | Rear underrun protection | Regulation (EU) 2019/2144 | B | B | B | B
A13 | Lateral protection | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
A14 | Fuel tank safety (IF) | Regulation (EU) 2019/2144 |
B
Liquid fuel tanks
Installation in vehicle
B
Liquid fuel tanks
Installation in vehicle
B
Liquid fuel tanks
Installation in vehicle
B
Liquid fuel tanks
Installation in vehicle
A15 | Liquified petroleum gas safety (IF) | Regulation (EU) 2019/2144 |
Components X
Installation B
Components X
Installation B
Components X
Installation B
Components X
Installation B
A16 | Compressed and liquified natural gas safety (IF) | Regulation (EU) 2019/2144 |
Components X
Installation B
Components X
Installation B
Components X
Installation B
Components X
Installation B
A17 | Hydrogen safety (IF) | Regulation (EU) 2019/2144 | X | X | X | X
A18 | Hydrogen system material qualification (IF) | Regulation (EU) 2019/2144 |
Components X
Installation B
Components X
Installation B
Components X
Installation B
Components X
Installation B
A19 | In-use electric safety (IF) | Regulation (EU) 2019/2144 | B | B | B | B
A20 | Frontal off-set impact | Regulation (EU) 2019/2144 |
B
Shall apply to vehicles fitted with front airbags. May comply with A21 Frontal full-width impact instead, at the choice of the manufacturer. Vehicles not fitted with airbags shall comply with A22 Protective steering (in full)
B
Shall apply to vehicles fitted with front airbags. May comply with A21 Frontal full-width impact instead, at the choice of the manufacturer. Vehicles not fitted with airbags shall comply with A22 Protective steering (in full)
Completed vehicles are deemed to comply with the frontal off-set impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
B |
B
Completed vehicles are deemed to comply with the frontal off-set impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
A21 | Frontal full-width impact | Regulation (EU) 2019/2144 |
B
On voluntary basis
B
On voluntary basis
Completed vehicles are deemed to comply with the frontal full-width impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
B |
B
Completed vehicles are deemed to comply with the frontal full-width impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
A22 | Protective steering | Regulation (EU) 2019/2144 |
B
Shall apply to vehicles that do not comply with A20 Frontal off-set impact or A21 Frontal full-width impact
B
Shall apply to vehicles that do not comply with A20 Frontal off-set impact or A21 Frontal full-width impact
B | B
A23 | Replacement airbag | Regulation (EU) 2019/2144 | equipment | equipment | equipment | equipment
A24 | Cab impact | Regulation (EU) 2019/2144 | not in scope |
B
Test A is required for vehicles with a maximum permissible mass of 1500 kg or more if compliance with A20 Frontal off-set impact, A21 Frontal full-width impact or A22 Protective steering was not demonstrated.
Test C is required only for vehicles which have a separate cab.
Completed vehicles are deemed to comply with cab impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase.
not in scope |
B
Test A is deemed to be fulfilled by means of A20 Frontal off-set impact, A21 Frontal full-width impact or A22 Protective steering.
Test C is required only for vehicles which have a separate cab.
Completed vehicles are deemed to comply with cab impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase.
A25 | Side impact | Regulation (EU) 2019/2144 |
B
Head form test
The manufacturer shall supply the technical service with suitable information concerning a possible impact of the head of the dummy against the structure of the vehicle or the side glazing, if made of laminated glazing.
When such impact is proven likely to happen, then the partial test using the head form test described in paragraph 3.1 of Annex 8 to UN Regulation No 95 shall be conducted and the criterion specified in paragraph 5.2.1.1 of UN Regulation No 95 shall be met.
In agreement with the technical service, the test procedure described in Annex 4 to UN Regulation No 21 may be used as an alternative to the test of UN Regulation No 95.
Alternatively, a full-scale test in accordance with UN Regulation No 95 may be carried out.
B
Head form test
The manufacturer shall supply the technical service with suitable information concerning a possible impact of the head of the dummy against the structure of the vehicle or the side glazing, if made of laminated glazing.
When such impact is proven likely to happen, then the partial test using the head form test described in paragraph 3.1 of Annex 8 to UN Regulation No 95 shall be conducted and the criterion specified in paragraph 5.2.1.1 of UN Regulation No 95 shall be met.
In agreement with the technical service, the test procedure described in Annex 4 to UN Regulation No 21 may be used as an alternative to the test of UN Regulation No 95.
Alternatively, a full-scale test in accordance with UN Regulation No 95 may be carried out.
Completed vehicles are deemed to comply with side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
B |
B
Completed vehicles are deemed to comply with side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
A26 | Pole side impact | Regulation (EU) 2019/2144 | n/a | n/a | B |
B
Completed vehicles are deemed to comply with the pole side impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase and the relevant restraint systems have not been modified to the extent that it would result in a decrease of the level of safety, as agreed by the technical service.
A27 | Rear impact | Regulation (EU) 2019/2144 | n/a | n/a | B |
B
Completed vehicles are deemed to comply with rear impact requirements provided that compliance has been demonstrated for at least the van or chassis-cab configuration, with appropriate powertrain, as part of a previous-stage type-approval, irrespective of the mass in running order increase.
A28 | 112-based eCall in-vehicles systems | Regulation (EU) 2015/758 | n/a | n/a | n/a | n/a
B | VULNERABLE ROAD USERS, VISION AND VISIBILITY
B1 | Pedestrian leg and head protection | Regulation (EU) 2019/2144 |
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
B2 | Enlarged head impact zone | Regulation (EU) 2019/2144 |
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
C
Date for refusal to grant EU type- approval: 7 January 2026
Date for the prohibition of the registration of vehicles: 7 July 2034
B3 | Frontal protection system | Regulation (EU) 2019/2144 | equipment | equipment | equipment | equipment
B4 | Advanced emergency braking for pedestrians and cyclists ahead | Regulation (EU) 2019/2144 |
IF B
Date for refusal to grant EU type- approval: 7 July 2026
Date for the prohibition of the registration of vehicles: 7 July 2028
IF B
Date for refusal to grant EU type- approval: 7 July 2026
Date for the prohibition of the registration of vehicles: 7 July 2028
B
Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level.
Date for refusal to grant EU type- approval: 7 July 2026
Date for the prohibition of the registration of vehicles: 7 July 2028
B
Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level.
Date for refusal to grant EU type- approval: 7 July 2026
Date for the prohibition of the registration of vehicles: 7 July 2028
B5 | Pedestrian and cyclist collision warning | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
B6 | Blind spot information system | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
B7 | Reversing detection | Regulation (EU) 2019/2144 | n/a | n/a | B | B
B8 | Forward vision | Regulation (EU) 2019/2144 | B |
B
Date for refusal to grant EU type- approval: 7 July 2026
Date for the prohibition of the registration of vehicles: 7 July 2028
B |
B
Date for refusal to grant EU type- approval: 7 July 2026
Date for the prohibition of the registration of vehicles: 7 July 2028
B9 | Heavy-duty vehicles direct vision | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
B10 | Safety glazing | Regulation (EU) 2019/2144 |
Components X
Installation B
Components X
Installation B
Components X
Installation B
Components X
Installation B
B11 | Defrost/demist | Regulation (EU) 2019/2144 |
B
Vehicles shall be fitted with an adequate windscreen defrosting and demisting device
B
Vehicles shall be fitted with an adequate windscreen defrosting and demisting device
B
Vehicles shall be fitted with an adequate windscreen defrosting and demisting device
B
Vehicles shall be fitted with an adequate windscreen defrosting and demisting device
B12 | Wash/wipe | Regulation (EU) 2019/2144 |
B
Vehicles shall be fitted with adequate windscreen washing and wiping devices
B
Vehicles shall be fitted with adequate windscreen washing and wiping devices
B
Vehicles shall be fitted with adequate windscreen washing and wiping devices
B
Vehicles shall be fitted with adequate windscreen washing and wiping devices
B13 | Indirect vision devices | Regulation (EU) 2019/2144 |
Components X
Installation on vehicle B
Components X
Installation on vehicle B
Components X
Installation on vehicle B
Components X
Installation on vehicle B
B14 | Acoustic Vehicle Alerting Systems | Regulation (EU) No 540/2014 | A | A | A | A
C | VEHICLE CHASSIS, BRAKING, TYRES AND STEERING
C1 | Steering equipment | Regulation (EU) 2019/2144 | B | B | B | B
C2 | Lane departure warning | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
C3 | Emergency lane keeping | Regulation (EU) 2019/2144 | IF B | IF B |
B
Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level.
B
Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level.
C4 | Braking | Regulation (EU) 2019/2144 | A | A | A | A
C5 | Replacement braking parts | Regulation (EU) 2019/2144 | equipment | equipment | equipment | equipment
C6 | Brake assist | Regulation (EU) 2019/2144 | IF B | IF B | B | B
C7 | Stability control | Regulation (EU) 2019/2144 | IF B | IF B | B | B
C8 | Advanced emergency braking on heavy-duty vehicles | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
C9 | Advanced emergency braking on light-duty vehicles | Regulation (EU) 2019/2144 | IF B | IF B |
B
Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level.
B
Not required for vehicles without a windscreen, with a foldable windscreen or with a windscreen where the maximum vertical distance between the top edge and lowest edge of the transparent surface does not exceed 300 mm (assessed excluding areas with less than 70 % transparency shade bands, dot-printed areas, text, graphics and transparent slots for regulatory sight lines) and where the R-point of the driver seat is not more than 450 mm from the ground level.
C10 | Tyre safety and environmental performance | Regulation (EU) 2019/2144 | X | X | X | X
C11 | Spare wheels and run-flat systems (IF) | Regulation (EU) 2019/2144 | X | X | X | X
C12 | Retreaded tyres | Regulation (EU) 2019/2144 | equipment | equipment | equipment | equipment
C13 | Tyre pressure monitoring for light-duty vehicles | Regulation (EU) 2019/2144 | n/a | n/a | B | B
C14 | Tyre pressure monitoring for heavy-duty vehicles | Regulation (EU) 2019/2144 | not in scope | not in scope | not in scope | not in scope
C15 | Tyre installation | Regulation (EU) 2019/2144 | B | B | B | B
C16 | Replacement wheels | Regulation (EU) 2019/2144 | equipment | equipment | equipment | equipment
D | ON-BOARD INSTRUMENTS, ELECTRICAL SYSTEM, VEHICLE LIGHTING AND PROTECTION AGAINST UNAUTHORISED USE, INCLUDING CYBERATTACKS
D1 | Audible warning | Regulation (EU) 2019/2144 |
Components X
Installation on vehicle B
Components X
Installation on vehicle B
Components X
Installation on vehicle B
Components X
Installation on vehicle B