ANNEX B ANNUAL ENERGY STATISTICS, Regulation (EU) 2019/2146

In forcesince 26 Nov 2019

This Annex describes the scope, units, reported period, frequency, deadline and transmission modalities for the annual collection of energy statistics.

The following provisions apply to all data collections specified in this annex:

(a)

Reported period: The reported period of declared data shall be a calendar year (1 January to 31 December), starting at reference year 2017.

(b)

Frequency: Data shall be declared on an annual basis.

(c)

Deadline for transmission of data: Data shall be sent in by 30 November of the year following the reported year, unless specified otherwise.

(d)

Transmission format: The transmission format shall conform to the relevant interchange standard specified by Eurostat.

(e)

Transmission method: Data shall be sent in or uploaded by electronic means to the single entry point for data at Eurostat.

Annex A includes explanations of terms for which a specific explanation is not supplied in this Annex.

Unless otherwise specified, this data collection applies to all energy products listed in Annex A, Chapter 3.1. COAL (solid fossil fuels and manufactured gases).

The following list of aggregates must be declared for all energy products listed in the previous paragraph unless otherwise specified.

Applicable only for anthracite, coking coal, other bituminous coal, subbituminous coal and lignite.

Applicable only for anthracite, coking coal, other bituminous coal, subbituminous coal and lignite.

This consists of two components:

recovered slurries, middlings and other low-grade coal products, which cannot be classified according to type of coal, including coal recovered from waste piles and other waste receptacles,

receipts from other sources.

Not applicable for anthracite, coking coal, other bituminous coal, subbituminous coal, lignite, peat, and oil shale and oil sands.

Not applicable for anthracite, coking coal, other bituminous coal, subbituminous coal, lignite, peat, and oil shale and oil sands.

Not applicable for anthracite, coking coal, other bituminous coal, subbituminous coal, lignite, peat, oil shale and oil sands.

Distribution losses also include flaring of manufactured gases.

Non-energy use in all industry, transformation and energy sub-sectors, e.g. coal used to make methanol or ammonia.

NACE Rev. 2 Divisions 20 and 21; non-energy use of coal includes use as feedstocks to produce fertiliser and as feedstocks for other petrochemical products.

Non-energy use in all transport sub-sectors.

Non-energy use in Commercial and Public Services, Households, Agriculture and Not Elsewhere Specified Other.

Imports by country of origin and exports by country of destination shall be reported. Applicable to anthracite, coking coal, other bituminous coal, sub-bituminous coal, lignite, patent fuel, coke oven coke, coal tar, BKB, peat, peat products and oil shale and oil sands.

Applicable for anthracite, coking coal, other bituminous coal, sub-bituminous coal, lignite, patent fuel, coke oven coke, gas coke, coal tar, BKB, peat, peat products, oil shale and oil sands.

Both gross and net calorific values are to be declared for the following aggregates:

Reported quantities must be declared in kt (kilo-tonnes), except for manufactured gases (gas works gas, coke oven gas, blast furnace gas, other recovered gases), where the reported quantity must be declared in TJ GCV (tera-joules based on gross calorific values).

Calorific values must be declared in MJ/t (mega-joules per tonne).

Not applicable.

This chapter covers the reporting of natural gas.

The following list of aggregates shall be declared for natural gas.

Declared quantities for the supply sector shall be expressed in both volume and energy units, and shall include the gross and net calorific values.

Includes off-shore production.

Natural gas produced in association with crude oil.

Natural gas originating from fields producing hydrocarbons only in gaseous form.

Methane produced at coal mines or from coal seams, piped to the surface and consumed at collieries or transmitted by pipeline to consumers.

Opening and closing stock levels shall be declared separately, as stocks on national territory and stocks held abroad, respectively. ‘Stock level’ means the quantity of gas available for delivery during any input-output cycle. This refers to recoverable natural gas stored in special storage facilities (depleted gas and/or oil field, aquifer, salt cavity, mixed caverns, or other), as well as stored liquefied natural gas. Cushion gas shall be excluded. The requirement of declaring calorific values is not applicable here.

The volume of gas released into the air on the production site or at the gas processing plant. The requirement of declaring calorific values is not applicable here.

The volume of gas burned in flares on the production site or at the gas processing plant. The requirement of declaring calorific values is not applicable here.

Final energy consumption and final non-energy consumption shall be declared separately for the following aggregates.

Final energy consumption and final non-energy consumption shall be declared separately for the following aggregates.

Final energy consumption and final non-energy consumption shall be declared separately for the following aggregates.

Both the quantities of total natural gas and of the LNG part of it shall be declared, per country of origin for imports and per country of destination for exports.

To be reported separately as gaseous gas storage facilities and LNG terminals (to be further distinguished as LNG import terminals or LNG export terminals).

Name of the site of the storage facility or the LNG terminal.

Type of storage, such as depleted gas field, aquifer, salt cavern, etc.

For gaseous gas storage facilities: total gas storage capacity, minus the cushion gas. The cushion gas is the total volume of gas required as a permanent inventory to maintain adequate underground storage reservoir pressures and deliverability rates throughout the output cycle.

For LNG terminals: total gas storage capacity expressed in gaseous gas equivalent.

Maximum rate at which gas can be withdrawn from the storage concerned; this corresponds to the maximum withdrawal capacity.

The regasifying capacity must be reported for import terminals and the liquefying capacity must be reported for export terminals.

Quantities of natural gas shall be declared as their energy content, i.e. in TJ, based on the gross calorific value. Where physical quantities are required, the unit is in 106 m3 assuming reference gas conditions (15 °C, 101325 Pa).

Calorific values shall be declared in kJ/m3, assuming reference gas conditions (15 °C, 101325 Pa).

Working capacity shall be declared in 106 m3, assuming reference gas conditions (15 °C, 101325 Pa).

Peak output, regasifying capacity and liquefying capacity shall be declared in 106 m3/day, assuming reference gas conditions (15 °C, 101325 Pa).

This chapter covers heat and electricity.

The following list of aggregates shall be declared for heat and electricity unless otherwise specified.

The following specific definitions apply to the electricity and heat aggregates discussed in this chapter:

Gross Electricity Production: the sum of the electrical energy produced by all the generating sets concerned (including pumped storage) measured at the output terminals of the main generators.

Gross Heat Production: the total heat produced by the installation, including the heat used by the installation’s auxiliaries that use a hot fluid (space heating, liquid fuel heating etc.) and losses in the installation/network heat exchanges, as well as heat from chemical processes used as a primary energy form.

Net Electricity Production: the gross electricity production less the electrical energy absorbed by the generating auxiliaries and the losses in the main generator transformers.

Net Heat Production: the heat supplied to the distribution system as determined based on measurements of the outgoing and return flows.

Aggregates 3.2.1.1 to 3.2.1.11 must be declared separately for main activity producers and for autoproducers. Within these two types of plant, both gross and net electricity and heat production must be declared for electricity-only, heat-only and CHP units, separately wherever applicable.

Fuels capable of igniting or burning, i.e. reacting with oxygen to produce a significant rise in temperature, and combusted directly for the production of electricity and/or heat.

Heat originating from processes without input energy, such as a chemical reaction. Excludes waste heat originating from energy-driven processes, which should be reported as heat produced from the corresponding fuel.

For 3.2.2.1 and 3.2.2.2., quantities declared shall be in coherence with the values declared for aggregates 3.2.1.1 to 3.2.1.11.

Amounts of electricity are considered as imported or exported when they have crossed the political boundaries of a country, whether customs clearance has taken place or not. If electricity transits through a country, the amount should be reported as both an import and an export.

See explanation under 3.2.2.3. ‘Imports’.

For electricity, includes losses in transformers which are not considered as integral parts of power plants.

Final energy consumption and final non-energy consumption shall be declared separately for the following aggregates.

Excludes plants’ own use for pumped storage, heat pumps and electric boilers.

Imports and exports of quantities of electricity and heat by country of origin and destination, respectively, have to be reported. See explanation under 3.2.2.3. ‘Imports’.

For the following plants or activities, net production of electricity and net generation of heat from autoproducers shall be declared separately for electricity-only, heat-only and CHP units:

The gross electricity produced, the heat sold and the fuel quantities used, including their corresponding total energy from the combustibles listed below, must be declared separately for main activity producers and for autoproducers. For these two types of producer, electricity and heat production must be declared separately wherever applicable for electricity-only, heat-only and CHP units.

The capacity shall be declared as on 31 December of the relevant reported year. Includes electrical capacity of both electricity-only and CHP units. The net maximum electrical capacity must be declared for both main activity producers and autoproducers. It is the sum of the net maximum capacities of all stations taken individually over a given period of operation. The period of operation assumed for present purposes is continuous running: in practice 15 hours or more per day. The net maximum capacity is the maximum power assumed to be solely active power that can be supplied, continuously, with the whole plant running, at the point of outlet to the network.

Net maximum electrical capacity of combustible fuels must be declared for both main activity producers and autoproducers, and separately for each type of single-fired or multi-fired plant mentioned below. Multi-fired systems include only units which can burn more than one fuel type on a continuous basis. Stations which have separate units using different fuels should be divided into the appropriate single-fuel categories. Indications on which type of fuel is used as primary and alternate must be added for each category of multi-fired plants.

Electricity shall be declared in GWh (giga-watt hours), heat in TJ (tera-joules) and capacity in MW (megawatts)

If reporting of other fuels is required, the applicable units are defined in the relevant chapters of this Annex.

Unless otherwise specified, this data collection applies to all energy products listed in Annex A, Chapter 3.4. Oil (crude oil and petroleum products)

The following list of aggregates shall be declared for all energy products listed in the previous paragraph, unless otherwise specified.

The following aggregates shall be declared for crude oil, NGL, refinery feedstocks, additives/oxygenates, biofuels in additives/oxygenates and other hydrocarbons:

Not applicable for refinery feedstocks and for biofuels.

Not applicable for crude oil, NGL and refinery feedstocks.

Only applicable for refinery feedstocks.

Only applicable for refinery feedstocks.

Includes quantities of crude oil and products imported or exported under processing agreements (i.e. refining on account). Crude oil and NGLs should be reported as coming from the country of ultimate origin; refinery feedstocks and finished products should be reported as coming from the country of last consignment. Includes any gas liquids (e.g. LPG) extracted during the regasification of imported liquefied natural gas and petroleum products imported or exported directly by the petrochemical industry. Note: all trade of biofuels which have not been blended with transport fuels (i.e. in their pure form) should not be reported here. Re-exports of oil imported for processing within bonded areas should be included as an export of product from the processing country to the final destination.

The note for imports (4.2.1.5.) also applies to exports.

Amounts measured as input to refineries

The difference between refinery intake (observed) and gross refinery output. Losses may occur during the distillation processes due to evaporation. Reported losses are positive. There may be volumetric gains but no gains in mass.

The following aggregates apply to finished products (refinery gas, ethane, LPG, naphtha, motor gasoline as well as its part of biogasoline, aviation gasoline, gasoline type jet fuel, kerosene type jet fuel as well as its bio part, other kerosene, gas/diesel oil, low and high sulphur fuel oil, white spirit and SBP, lubricants, bitumen, paraffin waxes, petroleum coke and other products). Crude oil and NGL used for direct burn should be included in deliveries of finished products and interproduct transfers.

Fuels used for production at refineries of electricity and heat sold should also be included in this category.

The note for imports in section 4.2.1.5. also applies here.

The note for imports in section 4.2.1.5. also applies here.

Changes in stocks which are held by public utilities and are not included in stock levels and stock changes reported elsewhere. A stock build is shown as a negative number and a stock draw is shown as a positive number.

The observed delivery of finished petroleum products from primary sources (e.g. refineries, blending plants, etc.) to the inland market.

Quantities of oil used as fuel for petrochemical processes such as steam cracking.

Quantities of oil used in the petrochemical sector for the purpose of producing ethylene, propylene, butylene, synthesis gas, aromatics, butadiene and other hydrocarbon-based raw materials in processes such as steam cracking, aromatics plants and steam reforming. Excludes amounts of oil used for fuel purposes.

Both the quantities involved in energy use and non-energy use shall be declared.

Both the quantities involved in energy use and non-energy use shall be declared.

Both the quantities involved in energy use and non-energy use shall be declared.

Both the quantities involved in energy use and non-energy use shall be declared.

Both the quantities involved in energy use and non-energy use shall be declared.

Both the quantities involved in energy use and non-energy use shall be declared.

Imports shall be declared by country of origin and exports by country of destination. The note for imports in section 4.2.1.5 also applies here.

Report the national total refining capacity and the breakdown of annual capacity by refinery in thousand metric tons per year. The following items shall be reported:

Reported quantities must be declared in kt (kilo-tonnes). Calorific values must be declared in MJ/t (mega-joules per tonne).

Cyprus is exempted from reporting the aggregates specified in Section 4.2.9 (Final energy consumption — Other Sectors); only the total values shall be reported. Cyprus is also exempted from reporting non-energy use under Sections 4.2.4 (Transformation sector), 4.2.5 (Energy Sector), 4.2.7 (Industry), 4.2.7.2 (Industry sector — of which Chemical and Petrochemical), 4.2.8 (Transport) and 4.2.9 (Other sectors).

Unless otherwise specified, this data collection applies to all energy products listed in Annex A, Chapter 3.5. Renewables and waste. Only quantities of fuels used for energy purposes (for example in electricity and heat generation, combustion with energy recovery, in mobile engines in transport and for use in stationary engines) should be reported. Quantities used for non-energy purposes shall be excluded from reporting (for example: wood in construction and for producing furniture, use of biolubricants for lubrication, use of biobitumen for road surface). Passive thermal energy shall also be excluded from reporting (for example: passive solar thermal heating of buildings).

Unless otherwise specified, the following list of aggregates shall be declared for all energy products listed in the previous paragraph. Ambient heat (heat pumps) only needs to be reported for the following sectors: Transformation (only for aggregates related to heat sold), Energy (only total, no subcategories), Industry total (only total, no subcategories), Commercial and Public Services, Households and Not elsewhere specified — Other.

The definitions of chapter 3.2.1. apply. The aggregates 5.2.1.1 to 5.2.1.18 must be declared separately for main activity producers and for autoproducers. For these two types of plant, gross electricity and gross heat production must be declared for electricity-only, heat-only and CHP units, separately wherever applicable.

Capacity shall be declared as on 31 December of the relevant reported year. Includes the electrical capacity of both electricity-only and CHP units. The net maximum electrical capacity is the sum of the net maximum capacities of all stations taken individually over a specific period of operation. The period of operation assumed for present purposes is continuous running: in practice 15 hours or more per day. The net maximum capacity is the maximum power assumed to be solely active power that can be supplied, continuously, with the whole plant running, at the point of outlet to the network.

The total surface area of the installed solar collectors is to be declared. The solar collector surface relates only to solar collectors used for the production of solar thermal heat; solar collector surface used for electricity generation does not have to be reported here (solar PV and concentrated solar power). The surface area of all solar collectors shall be included: glazed and unglazed collectors, flat-plate and vacuum tube with a liquid or air as the energy carrier.

The total production of solid biofuels (excluding charcoal) shall be split among the following fuels:

The total production of biogas shall be split among the following production methods:

Imports shall be reported by country of origin and exports by country of destination. Applicable to biogasolines, bioethanol, bio jet kerosene, biodiesels, other liquid biofuels, wood pellets.

Electricity shall be declared in GWh (giga-watt hours), heat in TJ (tera-joules) and electrical capacity in MW (megawatts).

Reported quantities shall be declared in TJ NCV (tera-joules based on net calorific value), except for charcoal, biogasoline, bioethanol, bio jet kerosenese, biodiesels, and other liquid biofuels which shall be declared in kt (kilo-tonnes).

Calorific values must be declared in MJ/t (mega-joules per tonne).

Solar collector surface shall be declared in 1000 m2.

Production capacity shall be declared in kt (kilo-tonnes) per year.

The following data concerning the civil use of nuclear energy must be declared:

The annual separative work capacity of operational enrichment plants (isotopic separation of uranium).

The annual production capacity of fuel fabrication plants. MOX fuel fabrication plants are excluded.

The annual production capacity of MOX fuel fabrication plants.

MOX is a fuel that contains a mixture of plutonium and uranium (mixed oxide).

Production of finished fresh fuel elements in nuclear fuel fabrication plants. Rods or other partial products are not included. Fabrication plants producing MOX fuel are also excluded.

Production of finished fresh fuel elements in MOX fuel fabrication plants. Rods or other partial products are not included.

The total amount of heat generated by nuclear reactors for the production of electricity or for other useful applications of heat.

Calculated average of the burnup of the fuel elements which have been definitively discharged from nuclear reactors during the reference year concerned. Excludes fuel elements which are temporarily discharged and are likely to be reloaded again later.

Uranium and plutonium produced in reprocessing plants during the reference year.

Annual reprocessing capacity of uranium and plutonium.

tSWU (tonnes of separative work units) for 6.1.1.

tHM (tonnes of heavy metal) for 6.1.4, 6.1.5., 6.1.8.

tHM (tonnes of heavy metal) per year for 6.1.2., 6.1.3, 6.1.9

TJ (tera-joules) for 6.1.6.

GWd/tHM (gigawatt-day per tonne of heavy metal) for 6.1.7.

The following disaggregated data concerning final energy consumption must be declared.

To be reported as per the definitions provided in section 2.6.1 of Annex A.

To be reported as per the definitions provided in section 2.6.3.2 of Annex A.

Only concerns electricity

Unless otherwise specified, this data collection applies to all energy products listed in Annex A.

Eurostat will specify the actual list of energy products for which data covered by point 7 of Annex B should be reported in the reporting template, as a subset of those listed in point 3 of Annex A.

Quantities of solid fossil fuels shall be declared in kt (kilo-tonnes);

Quantities of crude oil and petroleum products must be declared in kt (kilo-tonnes);

Quantities of natural gas and manufactured gases (gas works gas, coke oven gas, blast furnace gas, other recovered gases) must be declared by energy content, in TJ GCV (terajoules based on gross calorific values);

Electricity shall be declared in GWh (giga-watt hours);

Quantities of heat must be declared in TJ (tera-joules based on net calorific values);

Quantities of renewables and waste must be declared in TJ NCV (tera-joules based on net calorific value), except for charcoal, biogasoline, bioethanol, bio jet kerosenese, biodiesels, and other liquid biofuels, which shall be declared in kt (kilo-tonnes).

Calorific values for solid fossil fuels, crude oil and petroleum products and renewables and waste must be declared in MJ/t (mega-joules per tonne).

Calorific values for natural gas and manufactured gases shall be declared in kJ/m3, assuming reference gas conditions (15 °C, 101325 Pa).

For other energy products for which reporting is required, the applicable units are defined in the relevant chapters of this Annex.

This article is long: the rest is at the official publication.