Annex III is amended as follows:
in the table of contents the following references to Appendixes VII and VIII are added:
‘Appendix VII — Basic knowledge requirements for category L aircraft maintenance licence
Appendix VIII — Basic examination standards for category L aircraft maintenance licence’;
point 66.A.3 is replaced by the following:
Aircraft maintenance licences include the following categories and, where applicable, subcategories and system ratings:
Category A, divided into the following subcategories:
A1 Aeroplanes Turbine;
A2 Aeroplanes Piston;
A3 Helicopters Turbine;
A4 Helicopters Piston.
Category B1, divided into the following subcategories:
B1.1 Aeroplanes Turbine;
B1.2 Aeroplanes Piston;
B1.3 Helicopters Turbine;
B1.4 Helicopters Piston.
Category B2
The B2 licence is applicable to all aircraft.
Category B2L
The B2L licence is applicable to all aircraft other than those in Group 1 as set out in Point 66.A.5(1) and is divided into the following ‘system ratings’:
communication/navigation (com/nav),
instruments,
autoflight,
surveillance,
airframe systems.
A B2L licence shall contain, as a minimum, one system rating.
Category B3
The B3 licence is applicable to piston-engine non-pressurised aeroplanes of 2000 kg Maximum Take-off Mass (MTOM) and below.
Category L, divided into the following subcategories:
L1C: composite sailplanes,
L1: sailplanes,
L2C: composite powered sailplanes and composite ELA1 aeroplanes,
L2: powered sailplanes and ELA1 aeroplanes,
L3H: hot-air balloons,
L3G: gas balloons,
L4H: hot-air airships,
L4G: ELA2 gas airships,
L5: gas airships other than ELA2.
Category C
The C licence is applicable to aeroplanes and helicopters.’;
point 66.A.5 is replaced by the following:
For the purpose of ratings on aircraft maintenance licences, aircraft shall be classified into the following groups:
Group 1: complex motor-powered aircraft, helicopters with multiple engines, aeroplanes with maximum certified operating altitude exceeding FL290, aircraft equipped with fly-by-wire systems, gas airships other than ELA2 and other aircraft requiring an aircraft type rating when defined as such by the Agency.
The Agency may decide to classify into Group 2, Group 3 or Group 4, as appropriate, an aircraft which meets the conditions set out in the first subparagraph, if it considers that the lower complexity of the particular aircraft justifies so.
Group 2: aircraft other than those in Group 1 belonging to the following subgroups:
subgroup 2a:
single turboprop engine aeroplanes,
those turbojet and multiple-turboprop aeroplanes classified by the Agency in this subgroup because of their lower complexity.
subgroup 2b:
single turbine engine helicopters,
those multiple turbine engine helicopters classified by the Agency in this subgroup because of their lower complexity.
subgroup 2c:
single piston engine helicopters,
those multiple piston engine helicopters classified by the Agency in this subgroup because of their lower complexity.
Group 3: piston engine aeroplanes other than those in Group 1.
Group 4: sailplanes, powered sailplanes, balloons and airships, other than those in Group 1.’;
point 66.A.20(a) is amended as follows:
points (4) and (5) are replaced by the following:
‘4. A category B2L aircraft maintenance licence shall permit the holder to issue certificates of release to service and to act as B2L support staff for the following:
maintenance performed on electrical systems;
maintenance performed on avionics systems within the limits of the system ratings specifically endorsed on the licence, and
when holding the ‘airframe system’ rating, performance of electrical and avionics tasks within power plant and mechanical systems, requiring only simple tests to prove their serviceability.
A category B3 aircraft maintenance licence shall permit the holder to issue certificates of release to service and to act as B3 support staff for the following:
maintenance performed on aeroplane structure, power plant and mechanical and electrical systems; and
work on avionics systems requiring only simple tests to prove their serviceability and not requiring troubleshooting.’;
the following points (6) and (7) are added:
‘6. A category L aircraft maintenance licence shall permit the holder to issue certificates of release to service and to act as L support staff for the following:
maintenance performed on aircraft structure, power plant and mechanical and electrical systems;
work on radio, Emergency Locator Transmitters (ELT) and transponder systems; and
work on other avionics systems requiring simple tests to prove their serviceability.
Subcategory L2 includes subcategory L1. Any limitation to subcategory L2 in accordance with point 66.A.45(h) becomes also applicable to subcategory L1.
Subcategory L2C includes subcategory L1C.
A category C aircraft maintenance licence shall permit the holder to issue certificates of release to service following base maintenance of the aircraft. The privileges apply to the aircraft in its entirety.’;
in Point 66.A.25, point (a) is replaced by the following:
‘(a) For licences other than categories B2L and L, an applicant for an aircraft maintenance licence, or for the addition of a category or subcategory to such a licence, shall demonstrate by examination a level of knowledge of the appropriate subject modules in accordance with Appendix I to Annex III (Part-66). The examination shall comply with the standard set out in Appendix II to Annex III (Part-66) and shall be conducted either by a training organisation appropriately approved in accordance with Annex IV (Part-147), or by the competent authority.’;
point 66.A.25 is amended as follows:
points (b) and (c) are replaced by the following:
‘(b) An applicant for an aircraft maintenance licence in category L within a given subcategory, or for the addition of a different subcategory, shall demonstrate by examination a level of knowledge of the appropriate subject modules in accordance with Appendix VII to Annex III (Part-66). The examination shall comply with the standard set out in Appendix VIII to Annex III (Part-66) and shall be conducted by a training organisation appropriately approved in accordance with Annex IV (Part-147), by the competent authority or as agreed by the competent authority.
The holder of an aircraft maintenance licence in subcategory B1.2 or category B3 is deemed to meet the basic knowledge requirements for a licence in subcategories L1C, L1, L2C and L2.
The basic knowledge requirements for subcategory L4H include the basic knowledge requirements for subcategory L3H.
The basic knowledge requirements for subcategory L4G include the basic knowledge requirements for subcategory L3G.
An applicant for an aircraft maintenance licence in category B2L for a particular ‘system rating’, or for the addition of another ‘system rating’, shall demonstrate by examination a level of knowledge of the appropriate subject modules in accordance with Appendix I to Annex III (Part-66). The examination shall comply with the standard set out in Appendix II to Annex III (Part-66) and shall be conducted either by a training organisation appropriately approved in accordance with Annex IV (Part-147), or by the competent authority.’
the following points (d), (e) and (f) are added:
‘(d) The training courses and examinations shall have been passed within 10 years prior to the application for an aircraft maintenance licence or the addition of a category or subcategory to such a licence. Should this not be the case, examination credits may be obtained in accordance with point (e).
The applicant may apply to the competent authority for full or partial examination credits for the basic knowledge requirements for:
basic knowledge examinations that do not meet the requirement laid down in point (d);
any other technical qualification considered by the competent authority to be equivalent to the knowledge standard of Annex III (Part-66).
Credits shall be granted in accordance with Subpart E of Section B of this Annex (Part-66).
Credits expire 10 years after they were granted to the applicant by the competent authority. The applicant may apply for new credits after expiration.’;
in point 66.A.30(a) the following points (2a) and (2b) are inserted:
‘2a. for category B2L:
3 years of practical maintenance experience in operating aircraft, covering the corresponding system rating(s), if the applicant has no previous relevant technical training; or
2 years of practical maintenance experience in operating aircraft, covering the corresponding system rating(s), and completion of training, considered relevant by the competent authority, as a skilled worker in a technical trade; or
1 year of practical maintenance experience in operating aircraft, covering the corresponding system rating(s), and completion of a Part-147 approved basic training course.
For the addition of (a) new system rating(s) to an existing B2L licence, 3 months of practical maintenance experience relevant to the new system rating(s) shall be required for each system rating added.
for category L:
2 years of practical maintenance experience in operating aircraft covering a representative cross section of maintenance activities in the corresponding subcategory;
as a derogation from point (i), 1 year of practical maintenance experience in operating aircraft covering a representative cross section of maintenance activities in the corresponding subcategory, subject to the introduction of the limitation provided for in point 66.A.45(h)(ii)(3).
For the inclusion of an additional subcategory in an existing L licence, the experience required by points (i) and (ii) shall be 12 and 6 months respectively.
The holder of an aircraft maintenance licence in category/subcategory B1.2 or B3 is deemed to meet the basic experience requirements for a licence in subcategories L1C, L1, L2C and L2.’;
point 66.A.45 is replaced by the following:
In order to be entitled to exercise certification privileges on a specific aircraft type, the holder of an aircraft maintenance licence needs to have their licence endorsed with the relevant aircraft ratings:
For category B1, B2 or C, the relevant aircraft ratings are the following:
for Group 1 aircraft, the appropriate aircraft type rating;
for Group 2 aircraft, the appropriate aircraft type rating, manufacturer subgroup rating or full subgroup rating;
for Group 3 aircraft, the appropriate aircraft type rating or full group rating;
for Group 4 aircraft, for the category B2 licence, the full group rating.
For category B2L, the relevant aircraft ratings are the following:
for Group 2 aircraft, the appropriate manufacturer subgroup rating or full subgroup rating;
for Group 3 aircraft, the full group rating;
for Group 4 aircraft, the full group rating.
For category B3, the relevant rating is ‘piston-engine non-pressurised aeroplanes of 2000 kg MTOM and below’.
For category L, the relevant aircraft ratings are the following:
for subcategory L1C, the rating ‘composite sailplanes’;
for subcategory L1, the rating ‘sailplanes’;
for subcategory L2C, the rating ‘composite powered sailplanes and composite ELA1 aeroplanes’;
for subcategory L2, the rating ‘powered sailplanes and ELA1 aeroplanes’;
for subcategory L3H, the rating ‘hot-air balloons’;
for subcategory L3G, the rating ‘gas balloons’;
for subcategory L4H, the rating ‘hot-air airships’;
for subcategory L4G, the rating ‘ELA2 gas airships’;
for subcategory L5, the appropriate airship type rating.
For category A, no rating is required, subject to compliance with the requirements of point 145.A.35 of Annex II (Part-145).
The endorsement of aircraft type ratings requires the satisfactory completion of one of the following:
the relevant category B1, B2 or C aircraft type training in accordance with Appendix III to Annex III (Part-66);
in the case of gas airship type ratings on a B2 or L5 licence, a type training approved by the competent authority in accordance with point 66.B.130.
For other than category C licences, in addition to the requirements of point (b), the endorsement of the first aircraft type rating within a given category/subcategory requires satisfactory completion of the corresponding on-the-job training. This on-the-job training shall comply with Appendix III to Annex III (Part-66), except in the case of gas airships, where it shall be directly approved by the competent authority.
By derogation from points (b) and (c), for Group 2 and 3 aircraft, aircraft type ratings may also be endorsed on a licence after:
satisfactory completion of the relevant category B1, B2 or C aircraft type examination in accordance with Appendix III to this Annex (Part-66);
in the case of B1 and B2 category, demonstration of practical experience in the aircraft type. In that case, the practical experience shall include a representative cross section of maintenance activities relevant to the licence category.
In the case of a category C rating, for a person qualified by holding an academic degree as specified in point 66.A.30(a)(7), the first relevant aircraft type examination shall be at the category B1 or B2 level.
For Group 2 aircraft:
the endorsement of manufacturer subgroup ratings for category B1 and C licence holders requires complying with the aircraft type rating requirements for at least two aircraft types from the same manufacturer, which combined are representative of the applicable manufacturer subgroup;
the endorsement of full subgroup ratings for category B1 and C licence holders requires complying with the aircraft type rating requirements for at least three aircraft types from different manufacturers, which combined are representative of the applicable subgroup;
the endorsement of manufacturer subgroup and full subgroup ratings for category B2 and B2L licence holders requires demonstration of practical experience which shall include a representative cross section of maintenance activities relevant to the licence category and to the applicable aircraft subgroup and, in the case of the B2L licence, relevant to the applicable system rating(s);
by derogation from point (e)(iii), the holder of a B2 or B2L licence, endorsed with a full subgroup 2b, is entitled to be endorsed with a full subgroup 2c.
For Group 3 and 4 aircraft:
the endorsement of the full Group 3 rating for category B1, B2, B2L and C licence holders and the endorsement of the full Group 4 rating for B2 and B2L licence holders require demonstration of practical experience, which shall include a representative cross section of maintenance activities relevant to the licence category and to Group 3 or 4, as applicable;
for category B1, unless the applicant provides evidence of appropriate experience, Group 3 rating shall be subject to the following limitations, which shall be endorsed on the licence:
pressurised aeroplanes,
metal-structure aeroplanes,
composite-structure aeroplanes,
wooden-structure aeroplanes,
aeroplanes with metal-tubing structure covered with fabric;
by derogation from point (f)(i), the holder of a B2L licence, endorsed with a full subgroup 2a or 2b, is entitled to be endorsed with Groups 3 and 4.
For the B3 licence:
the endorsement of the rating ‘piston engine non-pressurised aeroplanes of 2000 kg MTOM and below’ requires demonstration of practical experience, which shall include a representative cross section of maintenance activities relevant to the licence category;
unless the applicant provides evidence of appropriate experience, the rating referred to in point (i) shall be subject to the following limitations, which shall be endorsed on the licence:
wooden-structure aeroplanes,
aeroplanes with metal-tubing structure covered with fabric,
metal-structure aeroplanes,
composite-structure aeroplanes.
For all L licence subcategories, other than L5:
the endorsement of ratings requires demonstration of practical experience which shall include a representative cross section of maintenance activities relevant to the licence subcategory;
unless the applicant provides evidence of appropriate experience, the ratings shall be subject to the following limitations, which shall be endorsed on the licence:
for ratings ‘sailplanes’ and ‘powered sailplanes and ELA1 aeroplanes’:
wooden-structure aircraft covered with fabric,
aircraft with metal-tubing structure covered with fabric,
metal-structure aircraft,
composite-structure aircraft,
for the rating ‘gas balloons’:
other than ELA1 gas balloons; and
if the applicant has only provided evidence of one-year experience in accordance with the derogation contained in point 66.A.30(a)(2b)(ii), the following limitation shall be endorsed on the licence:
‘complex maintenance tasks provided for in Appendix VII to Annex I (Part-M), standard changes provided for in point 21.A.90B of Annex I (Part-21) to Regulation (EU) No 748/2012 and standard repairs provided for in point 21.A.431B of Annex I (Part-21) to Regulation (EU) No 748/2012.’
The holder of an aircraft maintenance licence in subcategory B1.2 endorsed with the Group 3 rating, or in category B3 endorsed with the rating ‘piston engine non-pressurised aeroplanes of 2000 kg MTOM and below’, is deemed to meet the requirements for the issuance of a licence in subcategories L1 and L2 with the corresponding full ratings and with the same limitations as the B1.2/B3 licence held.’;
in point 66.A.50, point (a) is replaced by the following:
‘(a) Limitations introduced on an aircraft maintenance licence are exclusions from the certification privileges and, in the case of limitations referred to in point 66.A.45, they affect the aircraft in its entirety.’;
in point 66.A.70, points (c) and (d) are replaced by the following:
‘(c) Where necessary, the aircraft maintenance licence shall contain limitations in accordance with point 66.A.50 to reflect the differences between:
the scope of the certifying staff qualification valid in the Member State before the entry into force of the applicable licence category or subcategory provided for in this Annex (Part-66);
the basic knowledge requirements and the basic examination standards laid down in Appendices I and II to this Annex (Part-66).
By derogation from point (c), for aircraft not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, other than complex motor-powered aircraft, and for balloons, sailplanes, motor-powered sailplanes and airships, the aircraft maintenance licence shall contain limitations in accordance with point 66.A.50 to ensure that the certifying staff privileges valid in the Member State before the entry into force of the applicable Part-66 licence category/subcategory and those of the converted Part-66 aircraft maintenance licence remain the same.’;
point 66.B.100(b) is replaced by the following:
‘(b) The competent authority shall verify an applicant's examination status and/or confirm the validity of any credits to ensure that all module requirements of Appendix I or Appendix VII, as applicable, have been met as required by this Annex (Part-66).’;
point 66.B.110 is replaced by the following:
At the completion of the procedures specified in points 66.B.100 or 66.B.105, the competent authority shall endorse the additional basic category, subcategory or, for category B2L, system rating(s) on the aircraft maintenance licence by stamp and signature or shall reissue the licence.
The record system of the competent authority shall be changed accordingly.
Upon request by the applicant, the competent authority shall replace a licence in category B2L with a licence in category B2 endorsed with the same aircraft rating(s) when the holder has demonstrated both of the following:
by examination the differences between the basic knowledge corresponding to the B2L licence held and the basic knowledge of the B2 licence, as set out in Appendix I;
the practical experience required in Appendix IV.
In the case of a holder of an aircraft maintenance licence in subcategory B1.2 endorsed with the Group 3 rating or in category B3 endorsed with the rating ‘piston engine non-pressurised aeroplanes of 2000 kg MTOM and below’, the competent authority shall issue, upon application, a fully rated licence in subcategories L1 and L2, with the same limitations as the B1.2/B3 licence held.’;
in point 66.B.115, point (f) is replaced by the following:
‘(f) The competent authority shall ensure that compliance with the practical elements of the type training is demonstrated by one of the following:
by the provision of detailed practical training records or a logbook provided by the organisation which delivered the course directly approved by the competent authority in accordance with point 66.B.130;
where available, by a training certificate, covering the practical training element, issued by a maintenance training organisation appropriately approved in accordance with Annex IV (Part-147).’;
in point 66.B.125 point (b), point (1) is replaced by the following:
‘(1) for category B1 or C:
helicopter piston engine, full group: converted to ‘full subgroup 2c’ plus the aircraft type ratings for those single piston engine helicopters which are in Group 1;
helicopter piston engine, manufacturer group: converted to the corresponding ‘manufacturer subgroup 2c’ plus the aircraft type ratings for those single piston engine helicopters of that manufacturer which are in Group 1;
helicopter turbine engine, full group: converted to ‘full subgroup 2b’ plus the aircraft type ratings for those single turbine engine helicopters which are in Group 1;
helicopter turbine engine, manufacturer group: converted to the corresponding ‘manufacturer subgroup 2b’ plus the aircraft type ratings for those single turbine engine helicopters of that manufacturer which are in Group 1;
aeroplane single piston engine — metal structure, either full group or manufacturer group: converted to ‘full group 3’. For the B1 licence, the following limitations shall be included: composite-structure aeroplanes, wooden-structure aeroplanes, and metal-tubing and fabric aeroplanes;