7 Appendix VII, Regulation (EU) 2018/1142

In forcesince 14 Aug 2018

The definitions of the different levels of knowledge required in this Appendix are the same as those contained in point 1 of Appendix I to Annex III (Part-66).

Subcategories | Modules required for each subcategory (refer to the syllabus table below)

L1C: composite sailplanes | 1L, 2L, 3L, 5L, 7L and 12L

L1: sailplanes | 1L, 2L, 3L, 4L, 5L, 6L, 7L and 12L

L2C: composite powered sailplanes and composite ELA1 aeroplanes | 1L, 2L, 3L, 5L, 7L, 8L and 12L

L2: powered sailplanes and ELA1 aeroplanes | 1L, 2L, 3L, 4L, 5L, 6L, 7L, 8L and 12L

L3H: hot-air balloons | 1L, 2L, 3L, 9L and 12L

L3G: gas balloons | 1L, 2L, 3L, 10L and 12L

L4H: hot-air airships | 1L, 2L, 3L, 8L, 9L, 11L and 12L

L4G: ELA2 gas airships | 1L, 2L, 3L, 8L, 10L, 11L and 12L

L5: gas airships above ELA2 |

Basic knowledge requirements for any B1 subcategory

plus

8L (for B1.1 and B1.3), 10L, 11L and 12L

1L ‘Basic knowledge’

2L ‘Human factors’

3L ‘Aviation legislation’

4L ‘Airframe wooden/metal tube and fabric’

5L ‘Airframe composite’

6L ‘Airframe metal’

7L ‘Airframe general’

8L ‘Power plant’

9L ‘Balloon/Airship hot air’

10L ‘Balloon/Airship gas (free/tethered)’

11L ‘Airships hot air/gas’

12L ‘Radio Com/ELT/Transponder/Instruments’

Level

Arithmetical terms and signs;

Methods of multiplication and division;

Fractions and decimals;

Factors and multiples;

Weights, measures and conversion factors;

Ratio and proportion;

Averages and percentages;

Areas and volumes, squares, cubes.

Evaluating simple algebraic expressions: addition, subtraction, multiplication and division;

Use of brackets;

Simple algebraic fractions.

Simple geometrical constructions;

Graphical representation: nature and uses of graphs.

1

Nature of matter: the chemical elements;

Chemical compounds;

States: solid, liquid and gaseous;

Changes between states.

Forces, moments and couples, representation as vectors;

Centre of gravity;

Tension, compression, shear and torsion;

Nature and properties of solids, fluids and gases.

Thermometers and temperature scales: Celsius, Fahrenheit and Kelvin;

Heat definition.

1

Ohm's law, Kirchoff's voltage and current laws;

Significance of the internal resistance of a supply;

Resistance/resistor;

Resistor colour code, values and tolerances, preferred values, wattage ratings;

Resistors in series and parallel.

1

International Standard Atmosphere (ISA), application to aerodynamics and aerostatics.

Airflow around a body;

Boundary layer, laminar and turbulent flow;

Thrust, weight, aerodynamic resultant;

Generation of lift and drag: angle of attack, polar curve, stall.

Effect on envelopes, wind effect, altitude and temperature effects.

1

Safe working practices and precautions when working with electricity, gases (especially oxygen), oils and chemicals;

Labelling, storage and disposal of hazardous (to safety and environment) materials;

Remedial action in the event of a fire or another accident with one or more hazards, including knowledge of extinguishing agents.

2

Level

The need to take human factors into account;

Incidents attributable to human factors/human error;

Murphy's Law.

1

Vision, hearing, information processing, attention and perception, memory.

1

Responsibility, motivation, peer pressure, teamwork.

1

Fitness/health, stress, sleep, fatigue, alcohol, medication, drug abuse.

1

Working environment (climate, noise, illumination).

1

Level

Role of the European Commission, EASA and National Aviation Authorities (NAAs);

Applicable parts of Part-M and Part-66.

1

Approval of changes (repairs and modifications);

Standard changes and standard repairs.

2

Airworthiness Directives (ADs), Instructions for Continuing Airworthiness (ICA) (AMM, IPC, etc.);

Flight Manual;

Maintenance records.

2

Level

Timber, plywood, adhesives, preservation, power line, properties, machining;

Covering (covering materials, adhesives and finishes, natural and synthetic covering materials and adhesives);

Paint, assembly and repair processes;

Recognition of damages from overstressing of wooden/metal-tube and fabric structures;

Deterioration of wood components and coverings;

Crack test (optical procedure, e.g., magnifying glass) of metal components. Corrosion and preventive methods. Health and fire safety protections.

2

Types of wood, stability, and machining properties;

Steel and light alloy tubes and fittings, fracture inspections of welded seams;

Plastics (overview, understanding of the properties);

Paints and paint removal;

Glues, adhesives;

Covering materials and technologies (natural and synthetic polymers).

2

Overstress of wood / metal-tubing and fabric structures;

Load transfers;

Fatigue strength and crack testing.

3

Locking of pins, screws, castellated nuts, turnbuckles;

Thimble splice;

Nicopress and Talurit repairs;

Repair of coverings;

Repair of transparencies;

Repair exercises (plywood, stringer, handrails, skins);

Aircraft Rigging. Calculation of control surface mass balance and range of movement of the control surfaces, measurement of operating forces;

Performance of 100-hours/annual inspections on a wood or combination of metal-tube and fabric airframe.

2

Level

Basic principles of FRP construction;

Resins (Epoxy, polyester, phenolic resins, vinyl ester resins);

Reinforcement materials glass, aramide and carbon fibres, features;

Fillers;

Supporting cores (balsa, honeycombs, foamed plastics);

Constructions, load transfers (solid FRP shell, sandwiches);

Identification of damage during overstressing of components;

Procedure for FRP projects (according to Maintenance Organisation Manual) including storage conditions for material.

2

Thermosetting plastics, thermoplastic polymers, catalysts;

Understanding properties, machining technologies, detaching, bonding, welding;

Resins for FRP: epoxy resins, polyester resins, vinyl ester resins, phenolic resins;

Reinforcement materials;

From elementary fibre to filaments (release agent, finish), weaving patterns;

Properties of individual reinforcement materials (E-glass fibre, aramide fibre, carbon fibre);

Problem with multiple-material systems, matrix;

Adhesion/cohesion, various behaviours of fibre materials;

Filling materials and pigments;

Technical requirements for filling materials;

Property change of the resin composition through the use of E-glass, micro balloon, aerosols, cotton, minerals, metal powder, organic substances;

Paint assembly and repair technologies;

Support materials;

Honeycombs (paper, FRP, metal), balsa wood, Divinycell (Contizell), development trends.

2

Solid shell;

Sandwiches;

Assembly of aerofoils, fuselages, control surfaces.

2

Behaviour of FRP components in the event of overstressing;

Identifying delaminations, loose bonds;

Bending vibration frequency in aerofoils;

Load transfer;

Frictional connection and positive locking;

Fatigue strength and corrosion of metal parts;

Metal bonding, surface finishing of steel and aluminium components during bonding with FRP.

3

Plaster molds, mold ceramics;

GFK molds, Gel-coat, reinforcement materials, rigidity problems;

Metal molds;

Male and female molds.

2

Locking of pin, screws, castellated nuts, turnbuckles;

Thimble splice;

Nicopress and Talurit repairs;

Repair of coverings;

Repair of solid FRP shells;

Mold fabrication/molding of a component (e.g. fuselage nose, landing gear fairing, wing tip and winglet);

Repair of sandwich shell where interior and exterior layer are damaged;

Repair of sandwich shell by pressing with a vacuum bag;

Transparency repair (PMMA) with one- and two-component adhesive;

Bonding of transparency with the canopy frame;

Tempering of transparencies and other components;

Performance of a repair on a sandwich shell (minor repair less than 20 cm);

Aircraft Rigging. Calculation of control surface mass balance and range of movement of the control surfaces, measurement of operating forces;

Performance of 100-hour/annual inspections on an FRP airframe.

2

Level

Metallic materials and semi-finished products, machining methods;

Fatigue strength and crack test;

Assembly of metal-construction components, riveted joints, adhesive joints;

Identification of damage to overstressed components, effects of corrosion;

Health and fire protection.

2

Steel and its alloys;

Light metals and their light alloys;

Rivet materials;

Plastics;

Colours and paints;

Metal adhesives;

Types of corrosion;

Covering materials and technologies (natural and synthetic).

2

Overstressed metal airframes, levelling, measurement of symmetry;

Load transfers;

Fatigue strength and crack test;

Identifying loose riveted joints.

3

Skins;

Frames;

Stringers and longerons;

Frame construction;

Problems in multiple-material systems.

2

Classifications of fits and clearances;

Metric and imperial measuring systems;

Oversize bolt.

2

Locking of pins, screws, castellated nuts, turnbuckles;

Thimble splice;

Nicopress and Talurit repairs;

Repair of coverings, surface damage, stop drilling techniques;

Repair of transparencies;

Cutting out sheet metals (aluminiums and light alloys, steel and alloys);

Folding bending, edging, beating, smoothening, beading;

Repair riveting of metal airframes according to repair instruction or drawings;

Evaluation of rivet errors;

Aircraft Rigging. Calculation of control surface mass balance and range of movement of the control surfaces, measurement of operating forces;

Performance of 100-hour/annual inspections on a metal airframe.

2

Level

Cockpit controls: controls in cockpit, colour markings, knob shapes;

Flight controls surfaces, flaps, air brakes surfaces, controls, hinges, bearings, brackets, push-pull rods, bell cranks, horns, pulleys, cables, chains, tubes, rollers, tracks, jack screws, surfaces, movements, lubrication, stabilisers, balancing of controls;

Combination of controls: flap ailerons, flap air brakes;

Trim systems.

3

Landing gear: characteristics of landing gears and shock absorber strut, extension, brakes, drum, disks, wheel, tyre, retraction mechanism, electrical retraction, emergency;

Wing to fuselage mounting points, empennage (fin and tail plane) to fuselage mounting points, control surface mounting points;

Permissible maintenance measures;

Towing: towing/lifting equipment/mechanism;

Cabin: seats and safety harness, cabin arrangement, windshields, windows, placards, baggage compartment, cockpit controls, cabin air system, blower;

Water ballast: water reservoirs, lines, valves, drains, vents, tests;

Fuel system: tanks, lines, filters, vents, drains, filling, selector valve, pumps, indication, tests, bonding;

Hydraulics: system layout, accumulators, pressure and power distribution, indication;

Liquid and gas: hydraulic, other fluids, levels, reservoir, lines, valves, filter;

Protections: firewalls, fire protection, lightning strike bonding, turnbuckles, locking devices, dischargers.

2

Reliability of pins, rivets, screws;

Control cables, turnbuckles;

Quick-release couplings (L'Hotellier, SZD, Poland).

2

Admissibility of locking methods, locking pins, spring steel pins, locking wire, stop nuts, paint;

Quick-release couplings.

2

7L.5 Weight and balance levelling

2

7L.6 Rescue systems

2

Pitot-static system, vacuum/dynamic system, hydrostatic test;

Flight instruments: airspeed indicator, altimeter, vertical-speed indicator, connection and functioning, markings;

Arrangement and display, panel, electrical wires;

Gyroscopes, filters, indicating instruments; testing of function;

Magnetic compass: installation and compass swing;

Sailplanes: acoustic vertical-speed indicator, flight recorders, anticollision aid;

Oxygen system.

2

Flight instruments, mounting requirements (emergency landing conditions as per CS-22);

Electric wiring, power sources, types of storage batteries, electrical parameters, electric generator, circuit breaker, energy balance, earth/ground, connectors, terminals, warnings, fuses, lamps, lightings, switches, voltmeters, ampere meters, electrical gauges.

2

Interface between power plant and airframe.

2

Inspection;

Replacement;

Balancing.

2

Propeller position control;

Engine and/or propeller retraction system.

2

Cleaning, use of lighting and mirrors;

Measuring tools;

Measure of controls deflection;

Torque of screws and bolts;

Wear of bearings;

Inspection equipment;

Calibration of measuring tools.

2

Level

Explanation of the concept of ‘noise level’;

Noise certificate;

Enhanced sound proofing;

Possible reduction of sound emissions.

1

Four-stroke spark ignition engine, air-cooled engine, fluid-cooled engine;

Two-stroke engine;

Rotary-piston engine;

Efficiency and influencing factors (pressure–volume diagram, power curve);

Noise control devices.

2

Blade, spinner, backplate, accumulator pressure, hub;

Operation of propellers;

Variable-pitch propellers, ground and in-flight adjustable propellers, mechanically, electrically and hydraulically;

Balancing (static, dynamic);

Noise problems.

2

Mechanical control devices;

Electrical control devices;

Tank displays;

Functions, characteristics, typical errors and error indications.

2

Material and machining of fuel and oil hoses;

Control of life limit.

2

Operation of magneto ignition;

Control of maintenance limits;

Operation of carburettors;

Maintenance instructions on characteristic features;

Electric fuel pumps;

Operation of propeller controls;

Electrically operated propeller control;

Hydraulically operated propeller control.

2

Constructions: coil ignition, magneto ignition, and thyristor ignition;

Efficiency of the ignition and preheat system;

Modules of the ignition and preheat system;

Inspection and testing of a spark plug.

2

Operation and assembly;

Silencers and heater installations;

Nacelles and cowlings;

Inspection and test;

CO emission test.

2

Fuel characteristics;

Labelling, environmentally friendly storage;

Mineral and synthetic lubricating oils and their parameters: labelling and characteristics, application;

Environmentally friendly storage and proper disposal of used oil.

2

Manufacturer documents for the engine and propeller;

Instructions for Continuing Airworthiness (ICA);

Aircraft Flight Manuals (AFMs) and Aircraft Maintenance Manuals (AMMs);

Time Between Overhaul (TBO);

Airworthiness Directives (ADs), technical notes and service bulletins.

2

Cylinder unit with valve;

Carburettor;

High-tension magneto;

Differential-compression tester for cylinders;

Overheated/damaged pistons;

Spark plugs of engines that were operated differently.

2

Work safety/accident prevention (handling of fuels and lubricants, start-up of engines);

Rigging-engine control rods and Bowden cables;

Setting of no-load speed;

Checking and setting the ignition point;

Operational test of magnetos;

Checking the ignition system;

Testing and cleaning of spark plugs;

Performance of the engine tasks contained in an aeroplane 100-hour/annual inspection;

Cylinder compression test;

Static test and evaluation of the engine run;

Documentation of maintenance work including replacement of components.

2

Four-stroke reciprocating engine and control units;

Energy losses;

Ignition timing;

Direct flow behaviour of control units;

Wankel engine and control units;

Two-stroke engine and control units;

Scavenging;

Scavenging blower;

Idle range and power range.

2

Ignition;

Spark plugs;

Ignition system;

Combustion process;

Normal combustion;

Efficiency and medium pressure;

Engine knock and octane rating;

Combustion chamber shapes;

Fuel/air mix in the carburettor;

Carburettor principle, carburettor equation;

Simple carburettor;

Problems of the simple carburettor and their solutions;

Carburettor models;

Fuel/air mix during injection;

Mechanically controlled injection;

Electronically controlled injection;

Continuous injection;

Carburettor-injection comparison.

2

Special flight instruments (injection engine);

Interpretation of indications in a static test;

Interpretation of indications in flight at various flight levels.

2

Documentation, manufacturer documents, etc.;

General maintenance instructions (hourly inspections);

Functional tests;

Ground test run;

Test flight;

Troubleshooting in the event of faults in the injection system and their correction.

2

Work safety and safety provisions for work on injection systems.

2

Carburettor;

Components of injection system;

Aircraft with injection engine;

Tool for work on injection systems.

2

Energy system, accumulators, installation;

Electrical motor;

Heat, noise and vibration checks;

Testing windings;

Electrical wiring and control systems;

Pylon, extension and retraction systems;

Motor/propeller brake systems;

Motor ventilation systems;

Practical experience of 100-hour/annual inspections.

2

Engine installation;

Pylon, extension and retraction systems;

Fire protection;

Fuel systems including lubrication;

Engine starting systems, gas assist;

Engine damage assessment;

Engine servicing;

Engine removal / refit and test;

Practical experience of conditional / run time / annual inspections;

Conditional inspections.

2

8L.21 Full authority digital engine control (FADEC)

2

Level

Assembly and individual parts;

Envelopes;

Envelope Materials;

Envelope Systems;

Conventional and special shapes;

Fuel System;

Burner, burner frame and burner support rods;

Compressed-gas cylinders and compressed-gas hoses;

Basket and alternative devices (seats);

Rigging accessories;

Maintenance and servicing tasks;

Annual/100-hour inspection;

Log Books;

Aircraft Flight Manuals (AFMs) and Aircraft Maintenance Manuals (AMMs);

Rigging and launch preparation (launch restraint);

Launch.

3

Operating controls, maintenance and servicing jobs (according to flight manual).

3

Fabrics;

Seams;

Load tapes, rip stoppers;

Crown rings;

Parachute valve and fast-deflation systems;

Ripping panel;

Turning vent;

Diaphragms/catenaries (special shapes and airships);

Rollers, pulleys;

Control and shroud lines;

Knots;

Temperature indication label, temperature flag, envelope thermometer;

Flying wires;

Fittings, karabiners.

3

Burner coils;

Blast, liquid and pilot valves;

Burners/jets;

Pilot lights/vaporisers/jets;

Burner frame;

Fuel lines/hoses;

Fuel cylinders, valves and fittings.

3

Types of baskets (incl. alternative devices);

Basket materials: cane and willow, hide, wood, trim materials, suspension cables;

Seats, roller bearings;

Karabiner, shackle and pins;

Burner support rods;

Fuel cylinder straps;

Accessories.

3

Fire extinguisher, fire blanket;

Instruments (single or combined).

3

Stitching;

Bonding;

Basket hide/trim repairs.

3

Cleaning, use of lighting and mirrors;

Measuring tools;

Measure of controls deflection (only airships);

Torque of screws and bolts;

Wear of bearings (only airships);

Inspection equipment;

Calibration of measuring tools;

Fabric Grab Test.

2

Level

Assembly of individual parts;

Envelope and netting material;

Envelope, ripping panel, emergency opening, cords and belts;

Rigid gas valve;

Flexible gas valve (parachute);

Netting;

Load ring;

Basket and accessories (including alternative devices);

Electrostatic discharge paths;

Mooring line and drag rope;

Maintenance and servicing;

Annual inspection;

Flight papers;

Aircraft Flight Manuals (AFMs) and Aircraft Maintenance Manuals (AMMs);

Rigging and launch preparation;

Launch.

3

Operating controls;

Maintenance and servicing jobs (according to AMM and AFM);

Safety rules when using hydrogen as lifting gas.

3

Fabrics;

Poles and reinforcement of pole;

Ripping panel and cord;

Parachute and shroud lines;

Valves and cords;

Filler neck, Poeschel-ring and cords;

Electrostatic discharge paths.

3

Springs;

Gaskets;

Screwed joints;

Control lines;

Electrostatic discharge paths.

3

Kinds of net and other lines;

Mesh sizes and angles;

Net ring;

Knotting methods;

Electrostatic discharge paths.

3

10L.6 Load ring

3

Kinds of baskets (incl. alternative devices);

Strops and toggles;

Ballast system (bags and supports);

Electrostatic discharge paths.

3

10L.8 Ripping cord and valve cords

3

10L.9 Mooring line and drag rope

3

Bonding;

Splicing hemp ropes.

3

Instruments (single or combined).

3

Kinds of cables;

Acceptable damage of cable;

Cable swivel;

Cable clamps.

3

Kinds of winches;

Mechanical system;

Electrical system;

Emergency system;

Grounding/ballasting of winch.

3

Cleaning, use of lighting and mirrors;

Measuring tools;

Measure of controls deflection (only airships);

Torque of screws and bolts;

Wear of bearings (only airships);

Inspection equipment;

Calibration of measuring tools;

Fabric grab test.

2

Level

Envelope, ballonnets;

Valves, openings;

Gondola;

Propulsion;

Aircraft Flight Manuals (AFMs) and Aircraft Maintenance Manuals (AMMs);

Rigging and launch preparation.

3

Operating controls;

Maintenance and servicing jobs (according to AMM and AFM).

3

Fabrics;

Ripping panel and cords;

Valves;

Catenary system.

3

Kinds of gondolas (incl. alternative devices);

Airframe types and materials;

Identification of damage.

3

Basics about on-board electrical circuits;

Electrical sources (accumulators, fixation, ventilation, corrosion);

Lead, nickel-cadmium (NiCd) or other accumulators, dry batteries;

Generators;

Wiring, electrical connections;

Fuses;

External power source;

Energy balance.

3

Fuel system: tanks, lines, filters, vents, drains, filling, selector valve, pumps, indication, tests, bonding;

Propulsion instruments;

Basics about measuring and instruments;

Revolution measuring;

Pressure measuring;

Temperature measuring;

Available fuel/power measuring.

3

Fire extinguisher, fire blanket;

Instruments (single or combined).

3

Level

Channel spacing;

Basic functional test;

Batteries;

Testing and maintenance requirements.

2

Basic operation;

Typical portable configuration including antenna;

Explanation of Modes A, C, S;

Testing and maintenance requirements.

2

Handheld altimeter/variometers;

Batteries;

Basic functional test.

2