ANNEX VIII, Regulation (EU) 2018/989

In forcesince 18 May 2018

Annex VIII to Delegated Regulation (EU) 2017/654 is amended as follows:

(1)

in point 4.2.2.2, in the last paragraph, the following sentence is added:

‘A description of the connection for, and method to read, those records shall be included in the information folder as set out in Part A of Annex I of Implementing Regulation (EU) 2017/656.’;

(2)

in point 4.5.1, point (b) is replaced by the following:

‘(b) In case of a Type 2 engine, the resulting difference between the highest and the lowest maximum GERcycle within the family shall never exceed the range set out in point 2.4.15 of Annex IX to Implementing Regulation (EU) 2017/656, except as permitted by point 3.1.’;

(3)

point 6.4.1 is replaced by the following:

‘6.4.1. The manufacturer shall present the approval authority with evidence showing that the GERcycle span of all members of the dual-fuel engine family remains within the range set out in point 2.4.15 of Annex IX to Implementing Regulation (EU) 2017/656, or in the case of engines with an operator-adjustable GERcycle satisfy the requirements of point 6.5 (for example, through algorithms, functional analyses, calculations, simulations, results of previous tests, etc.).’;

(4)

the following point 6.8 is inserted:

A demonstration report shall document the demonstration conducted pursuant to points 6.1 to 6.7.1 The report shall:

(a)

describe the demonstration performed, including the applicable test cycle;

(b)

be included in the information folder as set out in Part A of Annex I of Implementing Regulation (EU) 2017/656.’;

(5)

Appendix 2 is amended as follows:

(a)

in point 7.1.3.2.1, the introductory wording of the first paragraph is replaced by the following:

‘In the case that the exact equations are applied to calculate instantaneous values of ugas in accordance with paragraph 7.1.3.2(a) then, when calculating the mass per test of a gaseous emission for transient (NRTC and LSI-NRTC) test cycles and RMC, ugas shall be included in the summation in equation (7-2) of point 2.1.2 of Annex VII by means of equation (8-1):’;

(b)

in point 7.1.3.3, the second paragraph is replaced by the following:

‘The requirements of point 8.2.1.2 of Annex VI shall apply for controlling the dilution ratio. In particular, if the combined transformation time of the exhaust gas flow measurement and the partial flow system exceeds 0,3 s, look-ahead control based on a pre-recorded test run shall be used. In this case, the combined rise time shall be ≤ 1 s and the combined delay time ≤ 10 s. Except in the case that the exhaust gas mass flow is measured directly the determination of exhaust gas mass flow shall use values of α, γ, δ and ε determined in accordance with point 7.1.5.3.’;

(c)

in point 7.1.3.4, in the paragraph under the heading, the first sentence is replaced by the following:

‘The flow meter referred to in points 9.4.5.3 and 9.4.5.4 of Annex VI shall not be sensitive to the changes in exhaust gas composition and density.’;

(d)

in point 7.1.4.1, the heading is replaced by the following:

(e)

point 7.1.5.2 is replaced by the following:

Equations (8-2) to (8-7) shall be used to calculate the elemental composition of the fuel mixture:

qmf = qmf1 + qmf2 | (8-2)

wH

wH1 qmf1 wH2 qmf2

qmf1 qmf2

(8-3)

wC

wC1 qmf1 wC2 qmf2

qmf1 qmf2

(8-4)

wS

wS1 qmf1 wS2 qmf2

qmf1 qmf2

(8-5)

wN

wN1 qmf1 wN2 qmf2

qmf1 qmf2

(8-6)

wO

wO1 qmf1 wO2 qmf2

qmf1 qmf2

(8-7)

where:

qmf1is the fuel mass flow rate of fuel 1 [kg/s]

qmf2is the fuel mass flow rate of fuel 2 [kg/s]

wHis the hydrogen content of fuel [% mass]

wCis the carbon content of fuel [% mass]

wSis the sulphur content of fuel [% mass]

wNis the nitrogen content of fuel [% mass]

wOis the oxygen content of fuel [% mass]’;

(f)

the following point 7.1.5.3 is inserted:

The calculation of the atomic ratios (especially the H/C-ratio α) is given in Annex VII by means of equations (8-8) to (8-11):

α11,9164

wH

wC

(8-8)

γ0,37464

wS

wC

(8-9)

δ0,85752

wN

wC

(8-10)

ε0,75072

wO

wC

(8-11)

where:

wHis the hydrogen content of fuel, mass fraction [g/g] or [% mass]

wCis the carbon content of fuel, mass fraction [g/g] or [% mass]

wSis the sulphur content of fuel, mass fraction [g/g] or [% mass]

wNis the nitrogen content of fuel, mass fraction [g/g] or [% mass]

wOis the oxygen content of fuel, mass fraction [g/g] or [% mass]

αis the molar hydrogen ratio (H/C)

γis the molar sulphur ratio (S/C)

δis the molar nitrogen ratio (N/C)

εis the molar oxygen ratio (O/C)

referring to a fuel CΗαΟεΝδSγ’.

(g)

in point 7.2.3, in the first paragraph, the last sentence is replaced by the following:

‘The instantaneous molar component ratios shall be input in the equations (7-88), (7-90), and (7-91) of Annex VII for the continuous chemical balance.’;

(h)

in point 7.2.3.1, the introductory wording of equation (8-16) is replaced by the following:

‘In cases where exhaust gas mass flow rate is calculated based on the mixed fuel rate then wC in equation (7-113) of Annex VII shall be calculated by means of equation (8-16):’.