2 Appendix I, Regulation (EU) 2018/150

In forcesince 30 Jan 2018

The method describes a procedure for the quantitative determination of phosphatidylserine (PS) and phosphatidylethanolamine (PE) in skimmed milk powder (SMP) and is suitable for detecting buttermilk solids in SMP.

PS + PE contentthe mass fraction of substance determined using the procedure here specified. The result is expressed as milligrams of phosphatidylethanolamine dipalmitoyl (PEDP) per 100 g powder.

Extraction of aminophospholipids by methanol from reconstituted milk powder. Determination of PS and PE as o-phthaldialdehyde (OPA) derivatives by reversed-phase (RP) HPLC and fluorescence detection. Quantification of PS and PE content in the test sample by reference to a standard sample containing a known amount of PEDP.

All reagents shall be of recognised analytical grade. Water shall be distilled or water of at least equivalent purity, unless otherwise specified.

Note: Standard material shall be stored at – 18 °C.

4.2.1.

HPLC-grade methanol

4.2.2.

HPLC-grade chloroform

4.2.3.

Tryptamine-monohydrochloride

4.3.1.

Sodium hydroxide, 12 M water solution

4.3.2.

Boric acid, 0,4 M water solution adjusted to pH 10,0 with sodium hydroxide (4.3.1)

4.3.3.

2-mercaptoethanol

4.3.4.

o-phthaldialdehyde (OPA)

4.4.1.

Elution solvents shall be prepared using HPLC-grade reagents.

4.4.2.

HPLC-grade water

4.4.3.

Methanol of tested fluorimetric purity

4.4.4.

Tetrahydrofuran

4.4.5.

Sodium dihydrogen phosphate

4.4.6.

Sodium acetate

4.4.7.

Acetic acid.

5.1.

Analytical balance, capable of weighing to the nearest 1 mg, with a readability of 0,1 mg

5.2.

Beakers, 25 and 100 ml capacity

5.3.

Pipettes, capable of delivering 1 and 10 ml

5.4.

Magnetic stirrer

5.5.

Graduated pipettes, capable of delivering 0,2, 0,5 and 5 ml

5.6.

Volumetric flasks, 10, 50 and 100 ml capacity

5.7.

Syringes, 20 and 100 μl capacity

5.8.

Ultrasonic bath

5.9.

Centrifuge, capable of operating at 27000 × g

5.10.

Glass vials, about 5 ml capacity

5.11.

Graduated cylinder, 25 ml capacity

5.12.

pH-meter, accurate to 0,1 pH units

5.13.1.

Gradient pumping system, capable of operating at 1,0 ml/min at 200 bar

5.13.2.

Autosampler with derivatisation capability

5.13.3.

Column heater, capable of maintaining the column at 30 °C ± 1 °C

5.13.4.

Fluorescence detector, capable of operating at 330 nm excitation wavelength and 440 nm emission wavelength

5.13.5.

Integrator or data processing software capable of peak area measurement

5.13.6.

A LiChrospher® — 100 column (250 × 4,6 mm) or an equivalent column packed with octadecylsilane (C 18), 5 μm particle size.

Sampling shall be carried out in accordance with ISO Standard 707.

7.1.1.

Weigh 30,0 ± 0,1 mg of tryptamine-monohydrochloride (4.2.3) into a 100 ml volumetric flask (5.6) and make up to the mark with methanol (4.2.1)

7.1.2.

Pipette 1 ml (5.3) of this solution into a 10 ml volumetric flask (5.6) and make up to the mark with methanol (4.2.1) in order to obtain a 0,15 mM tryptamine concentration

7.2.1.

Weigh 1,000 ± 0,001 g of the SMP sample into a 25 ml beaker (5.2). Add 10 ml of distilled water at 40 °C ± 1 °C by a pipette (5.3) and stir with a magnetic stirrer (5.4) for 30 minutes in order to dissolve any lumps

7.2.2.

Pipette 0,2 ml (5.5) of the reconstituted milk into a 10 ml volumetric flask (5.6), add 100 μl of the 0,15 mM tryptamine solution (7.1) using a syringe (5.7) and make up to the volume with methanol (4.2.1). Mix carefully by inversion and sonicate (5.8) for 15 min

7.2.3.

Centrifuge (5.9) at 27000 g × g for 10 minutes and collect the supernatant in a glass vial (5.10)

Note: Test sample solution should be stored at 4 °C until the HPLC analysis is performed.

7.3.1.

Weigh 55,4 mg PEDP (4.1) into a 50 ml volumetric flask (5.6) and add about 25 ml of chloroform (4.2.2) using a graduated cylinder (5.11). Heat the stoppered flask to 50 °C ± 1 °C and mix carefully till the PEDP dissolves. Cool the flask to 20 °C, make up to the volume with methanol (4.2.1) and mix by inversion

7.3.2.

Pipette 1 ml (5.3) of this solution into a 100 ml volumetric flask (5.6) and make up to the volume with methanol (4.2.1). Pipette 1 ml (5.3) of this solution into a 10 ml volumetric flask (5.6), add 100 μl (5.7) of 0,15 mM tryptamine solution (7.1) and make up to the volume with methanol (4.2.1). Mix by inversion

Note: Reference sample solution should be stored at 4 °C until the HPLC analysis is performed.

Weigh 25,0 ± 0,1 mg of OPA (4.3.4) into a 10 ml volumetric flask (5.6), add 0,5 ml (5.5) of methanol (4.2.1) and mix carefully to dissolve the OPA. Make up to the mark with boric acid solution (4.3.2) and add 20 μl of 2-mercaptoethanol (4.3.3) by syringe (5.7).

Note: The derivatising reagent should be stored at 4 °C in a brown glass vial and is stable for one week.

Solvent A: Solution of 0,3 mM sodium dihydrogen phosphate and 3 mM sodium acetate solution (adjusted to pH 6,5 ± 0,1 with acetic acid): methanol: tetrahydrofuran = 558:440:2 (v/v/v)

Solvent B: methanol

Time (min) | Solvent A (%) | Solvent B (%) | Flow rate (ml/min)

Initial | 40 | 60 | 0

0,1 | 40 | 60 | 0,1

5,0 | 40 | 60 | 0,1

6,0 | 40 | 60 | 1,0

6,5 | 40 | 60 | 1,0

9,0 | 36 | 64 | 1,0

10,0 | 20 | 80 | 1,0

11,5 | 16 | 84 | 1,0

12,0 | 16 | 84 | 1,0

16,0 | 10 | 90 | 1,0

19,0 | 0 | 100 | 1,0

20,0 | 0 | 100 | 1,0

21,0 | 40 | 60 | 1,0

29,0 | 40 | 60 | 1,0

30,0 | 40 | 60 | 0

Note: The eluting gradient may require slight modification in order to achieve the resolution shown in figure 1.

Column temperature: 30 °C.

7.5.3.

Injection volume: 50 μl derivatising reagent and 50 μl sample solution

Starting up the system on a daily basis, flush the column with 100 % solvent B for 15 minutes, then set at A:B = 40:60 and equilibrate at 1 ml/min for 15 minutes. Perform a blank run by injecting methanol (4.2.1).

Note: Before long-term storage flush the column with methanol: chloroform = 80:20 (v/v) for 30 minutes.

7.5.5.

Determine the PS + PE content in the test sample

7.5.6.

Perform the sequence of the chromatographic analyses keeping constant the run-to-run time in order to obtain constant retention times. Inject the external standard solution (7.3) every 5-10 test sample solutions in order to calculate the response factor

Note: The column shall be cleaned by flushing with 100 % solvent B (7.5.1) for at least 30 minutes every 20-25 runs.

PEDP is eluted as a single peak. Determine the peak area by valley-to- valley integration.

Tryptamine is eluted as a single peak (Figure 1). Determine the peak area by valley-to-valley integration.

Under the described conditions (Figure 1), PS elutes as two main partially unresolved peaks preceded by a minor peak. PE elutes as three main partially unresolved peaks. Determine the whole area of each peak cluster setting the baseline as reported in Figure 1.

PS and PE content in the test sample shall be calculated as follows:

C = 55,36 × ((A2)/(A1)) × ((T1)/(T2))

where:

CPS or PE content (mg/100 g powder) in the test sample

A 1PEDP peak area of the standard sample solution (7.3)

A 2PS or PE peak area of the test sample solution (7.2)

T 1Tryptamine peak area of the standard sample solution (7.3)

T 2Tryptamine peak area of the test sample solution (7.2).

Note: The values for repeatability were calculated according to the IDF International Standard (*).

The relative standard deviation of the repeatability, which expresses the variability of independent analytical results obtained by the same operator using the same apparatus under the same conditions on the same test sample and in a short interval of time, should not exceed 2 % relative. If two determinations are obtained under these conditions, the relative difference between the two results should not be greater than 6 % of the arithmetic mean of the results.

If two determinations are obtained by operators in different laboratories using different apparatus under different conditions for the analysis on the same test sample, the relative difference between the two results should not be greater than 11 % of the arithmetic mean of the results.

10.1.

Resmini P., Pellegrino L., Hogenboom J.A., Sadini V., Rampilli M., ‘Detection of buttermilk solids in skimmilk powder by HPLC quantification of aminophospholipids’. Sci. Tecn. Latt.-Cas., 39,395 (1988).