In accordance with Article 6, this Annex establishes the requirements to be met by the service providers.
Application for a service provider certificate or an amendment to an existing certificate shall be made in a form and manner established by the competent authority, taking into account the applicable requirements of this Regulation.
In accordance with Article 6, in order to obtain the certificate, the service provider shall comply with:
the requirements referred to in Article 8b(1) of Regulation (EU) No 216/2008;
the common requirements set out in this Annex;
the specific requirements set out in Annexes IV to XIII, where those requirements are applicable in light of the services that the service provider provides or plans to provide.
Notwithstanding point (b), the air traffic services provider may apply for a certificate limited to the provision of services in the airspace under the responsibility of the Member State where its principal place of operation or, if any, registered office is located, when it provides or plans to provide services only with respect to one or more of the following categories:
aerial work;
general aviation;
commercial air transport limited to aircraft with less than 10 tonnes of maximum take-off mass or less than 20 passenger seats;
commercial air transport with less than 10000 movements per year, regardless of the maximum take-off mass and the number of passenger seats; for the purposes of this provision, ‘movements’ means, in a given year, the average over the previous three years of the total number of take-offs and landings.
In addition, the following air navigation service providers may also apply for a limited certificate:
an air navigation service provider, other than a provider of air traffic services, with a gross annual turnover of EUR 1000000 or less in relation to the services they provide or plan to provide;
an air navigation service provider providing aerodrome flight information services by operating regularly not more than one working position at any aerodrome.
As determined by the competent authority, an air navigation service provider applying for a limited certificate in accordance with points (a) or (b)(1) shall comply, as a minimum, with the following requirements set out in:
point ATM/ANS.OR.B.001 Technical and operational competence and capability;
point ATM/ANS.OR.B.005 Management system;
point ATM/ANS.OR.B.020 Personnel requirements;
point ATM/ANS.OR.A.075 Open and transparent provision of services;
Annexes IV, V, VI and VIII, where those requirements are applicable in light of the services that the service provider provides or plans to provide, in accordance with Article 6.
As determined by the competent authority, the air navigation service provider applying for a limited certificate in accordance with point (b)(2) shall comply, as a minimum, with the requirements set out in points (c)(1) to (c)(4) and with the specific requirements set out in Annex IV.
An applicant for a limited certificate shall submit an application to the competent authority in a form and manner established by the competent authority.
Pursuant to Article 7, a flight information services provider may declare its capability and means of discharging the responsibilities associated with the services provided where it meets, in addition to the requirements referred to in Article 8b(1) of Regulation (EU) No 216/2008, the following alternative requirements:
the flight information services provider provides, or plans to provide, its services by operating regularly not more than one working position;
those services are of a temporary nature, for a duration agreed with the competent authority as necessary to ensure proportional safety assurance.
A flight information services provider declaring its activities shall:
provide the competent authority with all the relevant information prior to commencing operations, in a form and manner established by the competent authority;
provide the competent authority with a list of the alternative means of compliance used, in accordance with point ATM/ANS.OR.A.020;
maintain compliance with the applicable requirements and with the information given in the declaration;
notify the competent authority of any changes to its declaration or the means of compliance it uses through submission of an amended declaration;
provide its services in accordance with its operations manual and comply with all the relevant provisions contained therein.
Before ceasing the provision of its services, the flight information services provider declaring its activities shall notify the competent authority within a period determined by the competent authority.
A flight information services provider declaring its activities shall comply with the following requirements set out in:
point ATM/ANS.OR.A.001 Scope;
point ATM/ANS.OR.A.020 Means of compliance;
point ATM/ANS.OR.A.035 Demonstration of compliance;
point ATM/ANS.OR.A.040 Changes — general;
point ATM/ANS.OR.A.045 Changes to the functional system;
point ATM/ANS.OR.A.050 Facilitation and cooperation;
point ATM/ANS.OR.A.055 Findings and corrective actions;
point ATM/ANS.OR.A.060 Immediate reaction to a safety problem;
point ATM/ANS.OR.A.065 Occurrence reporting;
point ATM/ANS.OR.B.001 Technical and operational competence and capability;
point ATM/ANS.OR.B.005 Management system;
point ATM/ANS.OR.B.020 Personnel requirements;
point ATM/ANS.OR.B.035 Operations manuals;
point ATM/ANS.OR.D.020 Liability and insurance cover,
Annex IV.
A flight information services provider declaring its activities shall only start operation after receiving the acknowledgement of receipt of the declaration from the competent authority.
Alternative means of compliance (AltMOC) to the AMC adopted by the Agency may be used by the service provider to establish compliance with the requirements of this Regulation.
When the service provider wishes to use an AltMOC, it shall, prior to implementing it, provide the competent authority with a full description of the AltMOC. The description shall include any revisions to manuals or procedures that may be relevant, as well as an assessment demonstrating compliance with the requirements of this Regulation.
A service provider may implement these alternative means of compliance subject to prior approval by the competent authority and upon receipt of the notification as prescribed in point ATM/ANS.AR.A.015(d).
A service provider's certificate shall remain valid subject to:
the service provider remaining in compliance with the applicable requirements of this Regulation, including those concerning facilitating and cooperating for the purposes of the exercise of the powers of the competent authorities and those concerning the handling of findings as specified in points ATM/ANS.OR.A.050 and ATM/ANS.OR.A.055 respectively;
the certificate not having been surrendered, suspended or revoked.
Upon revocation or surrender, the certificate shall be returned to the competent authority without delay.
A declaration made by the flight information services provider in accordance with point ATM/ANS.OR.A.015 shall remain valid subject to:
the flight information services remaining in compliance with the applicable requirements of this Regulation, including those concerning facilitating and cooperating for the purposes of the exercise of the powers of the competent authorities and those concerning the handling of findings as specified in point ATM/ANS.OR.A.050 and ATM/ANS.OR.A.055 respectively;
the declaration not having been withdrawn by the provider of such services or deregistered by the competent authority.
A service provider shall provide all the relevant evidence to demonstrate compliance with the applicable requirements of this Regulation at the request of the competent authority.
The notification and management of:
a change to the functional system or a change that affects the functional system shall be carried out in accordance with point ATM/ANS.OR.A.045;
a change to the provision of service, the service provider's management system and/or safety management system, that does not affect the functional system, shall be carried out in accordance with point (b).
Any change as referred to in point (a)(2) shall require prior approval before implementation, unless such a change is notified and managed in accordance with a procedure approved by the competent authority as laid down in point ATM/ANS.AR.C.025(c).
A service provider planning a change to its functional system shall:
notify the competent authority of the change;
provide the competent authority, if requested, with any additional information that allows the competent authority to decide whether or not to review the argument for the change;
inform other service providers and, where feasible, aviation undertakings affected by the planned change.
Having notified a change, the service provider shall inform the competent authority whenever the information provided in accordance with points (a)(1) and (2) is materially modified, and the relevant service providers and aviation undertakings whenever the information provided in accordance with point (a)(3) is materially modified.
A service provider shall only allow the parts of the change, for which the activities required by the procedures referred to in point ATM/ANS.OR.B.010 have been completed, to enter into operational service.
If the change is subject to competent authority review in accordance with point ATM/ANS.AR.C.035, the service provider shall only allow the parts of the change for which the competent authority has approved the argument to enter into operational service.
When a change affects other service providers and/or aviation undertakings, as identified in point (a)(3), the service provider and these other service providers, in coordination, shall determine:
the dependencies with each other and, where feasible, with the affected aviation undertakings;
the assumptions and risk mitigations that relate to more than one service provider or aviation undertaking.
Those service providers affected by the assumptions and risk mitigations referred to in point (e)(2) shall only use, in their argument for the change, agreed and aligned assumptions and risk mitigations with each other and, where feasible, with aviation undertakings.
Before integrating ATM/ANS equipment into the functional system, the ATM/ANS provider shall ensure that:
new or modified ATM/ANS equipment is certified by the Agency in accordance with Delegated Regulation (EU) 2023/1768 and manufactured by an approved design or production organisation pursuant to Commission Implementing Regulation (EU) 2023/1769 [Commission Implementing Regulation (EU) 2023/1769 of 12 September 2023 laying down technical requirements and administrative procedures for the approval of organisations involved in the design or production of air traffic management/air navigation services systems and constituents and amending Implementing Regulation (EU) 2023/203 (OJ L 228, 15.9.2023, p. 19).]; or
new or modified ATM/ANS equipment is declared by an approved design organisation pursuant to Delegated Regulation (EU) 2023/1768 and manufactured by an approved design or production organisation pursuant to Implementing Regulation (EU) 2023/1769; or
new or modified ATM/ANS equipment is issued with a statement of compliance in accordance with Article 6(1) of Delegated Regulation (EU) 2023/1768; or
when the ATM/ANS equipment is not subject to the conformity assessment under Delegated Regulation (EU) 2023/1768, the particular ATM/ANS equipment has been verified to comply with the applicable specifications and qualifications.
The ATM/ANS provider shall ensure that the ATM/ANS equipment has been verified to comply with the equipment manufacturer’s specifications, including installation and on-site test(s).
Before the ATM/ANS provider puts the ATM/ANS equipment into service, it shall ensure that the modified functional system integrating this ATM/ANS equipment meets all the applicable requirements and shall identify all deviations and limitations.
When the ATM/ANS provider puts the ATM/ANS equipment into service, it shall ensure that the ATM/ANS equipment, or the modified one, is deployed according to the conditions of use, as well as to any applicable limitations, and meets all the applicable requirements.
A service provider shall facilitate inspections and audits by the competent authority or by a qualified entity acting on its behalf and it shall cooperate as necessary for the efficient and effective exercise of the powers of the competent authorities referred to in Article 5.
After receipt of notification of findings from the competent authority, the service provider shall:
identify the root cause of the non-compliance;
define a corrective action plan that meets the approval by the competent authority;
demonstrate corrective action implementation to the satisfaction of the competent authority within the time period proposed by the service provider and agreed with that authority, as defined in point ATM/ANS.AR.C.050(e).
A service provider shall implement any safety measures, including safety directives, mandated by the competent authority in accordance with point ATM/ANS.AR.A.025(c).
When a safety directive is issued to correct the condition referred to in the statement of compliance issued in accordance with Article 6 of Delegated Regulation (EU) 2023/1768, the ATM/ANS provider shall, unless otherwise determined by the competent authority in case urgent action is needed:
propose appropriate corrective action and submit details of that proposal to the competent authority for approval;
following the approval by the competent authority, comply therewith.
As part of its management system, the ATM/ANS provider shall establish and maintain an occurrence-reporting system, including mandatory and voluntary reporting. ATM/ANS providers established in a Member State shall ensure that the system complies with the requirements of Regulation (EU) No 376/2014 and Regulation (EU) 2018/1139, as well as with the delegated and implementing acts adopted on the basis of those regulations.
The ATM/ANS provider shall report to the competent authority and to any other organisation required to be informed by the Member State, where the ATM/ANS provider provides its services, any safety-related event or condition that endangers or, if not corrected or addressed, could endanger an aircraft, its occupants or any other person, and in particular any accident or serious incident.
Without prejudice to point (b), the ATM/ANS provider shall report to the competent authority and to the organisation responsible for the design and/or maintenance of the ATM/ANS systems and constituents, if different from the ATM/ANS provider, any malfunction, technical defect, exceedance of technical limitations, occurrence, or other irregular circumstance that has or may have endangered the safety of services and has not resulted in an accident or serious incident.
Without prejudice to Regulation (EU) No 376/2014 and the delegated and implementing acts adopted on the basis thereof, reports shall:
be made as soon as practicable, but in any case within 72 hours after the ATM/ANS provider has become aware of the event or condition to which the report relates, unless exceptional circumstances prevent this;
be made in a form and manner established by the competent authority;
contain all pertinent information about the condition known to the ATM/ANS provider.
For ATM/ANS providers that are not established in a Member State, initial mandatory reports shall:
appropriately safeguard the confidentiality of the identity of the reporter and of the persons mentioned in the report;
be made as soon as practicable, but in any case within 72 hours after the ATM/ANS provider has become aware of the occurrence, unless exceptional circumstances prevent this;
be made in a form and manner established by the competent authority;
contain all pertinent information about the condition known to the ATM/ANS provider.
Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, where relevant, a follow-up report providing details of actions the organisation intends to take to prevent similar occurrences in the future shall be made as soon as these actions have been identified; those follow-up reports shall:
be sent to the relevant entities initially reported to in accordance with points (b) and (c); and
be made in a form and manner established by the competent authority.
A service provider shall have in place contingency plans for all the services it provides in the case of events which result in significant degradation or interruption of its operations.
A service provider shall provide its services in an open and transparent manner. It shall publish the conditions of access to its services and changes thereto and establish a consultation process with the users of its services on a regular basis or as needed for specific changes in service provision, either individually or collectively.
A service provider shall not discriminate on grounds of nationality or other characteristic of the user or the class of users of its services in a manner that is contrary to Union law.
A service provider shall ensure that aeronautical data related to its services is provided in due time to the AIS provider.
When aeronautical data related to its services is published, the service provider shall:
monitor the data;
notify the AIS provider of any changes necessary to ensure that the data is correct and complete;
notify the AIS provider when the data is incorrect or inappropriate.
When originating, processing or transmitting data to the AIS provider, the service provider shall:
ensure that aeronautical data referred to in Appendix 1 conform to the specifications of the aeronautical data catalogue;
ensure that the following data quality requirements are met:
the accuracy of aeronautical data is as specified in the aeronautical data catalogue;
the integrity of aeronautical data is maintained;
based on the integrity classification specified in the aeronautical data catalogue, procedures are put in place so that:
for routine data, corruption is avoided throughout the processing of the data;
for essential data, corruption does not occur at any stage of the entire process and additional processes are included, as needed, to address potential risks in the overall system architecture to further assure data integrity at this level;
for critical data, corruption does not occur at any stage of the entire process and additional integrity assurance processes are included to fully mitigate the effects of faults identified as potential data integrity risks by thorough analysis of the overall system architecture;
the resolution of aeronautical data is commensurate with the actual data accuracy;
the traceability of aeronautical data is ensured;
the timeliness of the aeronautical data is ensured, including any limits on the effective period of the data;
the completeness of the aeronautical data is ensured;
the delivered data meet the specified format requirements;
with regard to data origination, establish specific formal arrangements with the party originating data that contain instructions for data creation, modification or deletion, which include as a minimum:
an unambiguous description of the aeronautical data to be created, modified or deleted;
the entity to which the aeronautical data is to be provided;
the date and time by which the aeronautical data is to be provided;
the format of the data origination report to be used;
the format of the aeronautical data to be transmitted;
the requirement to identify any limitation on the use of the data;
ensure that data validation and verification techniques are employed to ensure that the aeronautical data meets the associated data quality requirements and in addition:
the verification shall ensure that aeronautical data is received without corruption and that corruption does not occur at any stage of the entire aeronautical data process;
aeronautical data and aeronautical information entered manually shall be subject to independent verification to detect any errors that may have been introduced;
when using aeronautical data to derive or calculate new aeronautical data, the initial data shall be verified and validated, except when provided by an authoritative source;
transmit aeronautical data by electronic means;
establish formal arrangements with:
all parties transmitting data to them;
other service providers or aerodrome operators when exchanging aeronautical data and aeronautical information;
ensure that the information listed in point AIS.TR.505(a) is provided in due time to the AIS provider;
collect and transmit metadata which include as a minimum:
the identification of the organisations or entities performing any action of originating, transmitting or manipulating the aeronautical data;
the action performed;
the date and time the action was performed;
ensure that tools and software used to support or automate aeronautical data and aeronautical information processes perform their functions without adversely impacting the quality of aeronautical data and aeronautical information;
ensure that digital data error detection techniques are used during the transmission or storage of aeronautical data, or both, in order to support the applicable data integrity levels;
ensure that the transfer of aeronautical data is subject to a suitable authentication process such that recipients are able to confirm that the data has been transmitted by an authorised source;
ensure that errors identified during data origination and after data delivery are addressed, corrected or resolved and that priority is given to managing errors in critical and essential aeronautical data.
For the purpose of air navigation, service providers shall use:
the World Geodetic System – 1984 (WGS-84) as the horizontal reference system;
the mean sea level (MSL) datum as the vertical reference system;
the Gregorian calendar and coordinated universal time (UTC) as the temporal reference systems.