Manufacturer's declaration of conversion of (L3e/L4e)-A2 to (L3e/L4e)-A3 motorcycle characteristics and vice-versa
A duly-completed version of this statement shall be included in the information folder.
The undersigned: […(full name and position)]
0.4.
Company name and address of manufacturer: …
0.4.2.
Name and address of the manufacturer's representative (if any)(0): …
Declares that
The (L3e/L4e)-A2 or (L3e/L4e)-A3(1) motorcycle:
0.2. Type(4): …
0.2.1. Variant(s)(4): …
0.2.2. Version(s)(4): …
0.2.3 Commercial name(s) (if available): …
0.3. Category, subcategory and sub-subcategory of vehicle(5): …
Type-approval number (if available): …
1.1. Type-approval issued on (date, if available): …
3.2.2.1. PCUs/ECUs(1) software identification number(s): …and calibration verification number(s): …
is technically suitable to be retrofitted to the (L3e/L4e)-A2 or (L3e/L4e)-A3(1) vehicle identified below:
0.2. Type(4): …
0.2.1. Variant(s)(4): …
0.2.2. Version(s)(4): …
0.2.3 Commercial name(s) (if available): …
0.3. Category, subcategory and sub-subcategory of vehicle(5): …
Type-approval number (if available): …
1.1. Type-approval issued on (date, if available): …
3.2.2.1. PCUs/ECUs(1) software identification number(s): …and calibration verification number(s): …
With the following technical characteristics:
1.8.
Maximum design vehicle speed: …km/h
1.9.
Maximum net power: …kW (at …min-1)(1)
1.10.
Ratio maximum net power/mass of the vehicle in running order: …kW/kg
4.0.6.
Sound level measured according to(2): …
4.0.6.1.
Stationary: …dB(A) at engine speed: …min-1
4.0.6.2.
Drive-by: …dB(A)
4.0.6.3.
Limit value for Lurban(0)(7): …dB(A)
3.2.15.
Exhaust emissions measured according to(2): …
3.2.15.1.
Type I test: tailpipe emissions after cold start, including the deterioration factor:
CO: …mg/km
THC: …mg/km
NMHC(0): …mg/km
NOx: …mg/km
THC+NOx(0): …mg/km
PM(0): …mg/km
8.7.3.2.
Type II test: tailpipe emissions at (increased) idle and free acceleration:
HC: …ppm at normal idling speed and: …ppm at high idle speed
CO: …% vol. at normal idling speed and: …% vol. at high idle speed
8.7.3.2.1.
Smoke corrected absorption coefficient: …m–1
4.0.2.
Fuel consumption(0)(6): …l or kg/100 km
4.0.3.
CO2 emissions(0)(6): …g/km
4.0.4.
Energy consumption(0)(6): …Wh/km
4.0.5.
Electric range(0): …km
by modifying the following components, parts, software, etc.: …
…
Place: …
Date: …
Signature: …
Name and position in the company: …
Suppress the entry if not applicable.
Delete where not applicable (no deletion required when more than one entry is applicable).
Number of the Commission Delegated Regulation and latest amending Commission Delegated Regulation applicable to the type-approval. In the case of a Commission Delegated Regulation with two or more implementation stages; indicate also the implementation stage and/or code. Alternatively indicate the number of the applicable UNECE Regulation.
Round the units of measure to the nearest whole number for dB(A), Wh/ km, mg/ km, g/km, ppm and km; to the nearest tenth for kW, l/ 100 km, kg/ 100 km, m3/ 100 km and for % vol; and to the nearest hundredth for kW/ kg and for m–1.
Indicate the alphanumeric code Type-Variant-Version or ‘TVV’ allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I.
Classified according to Article 4 of and Annex I to Regulation (EU) No 168/2013, the coding shall be indicated, e.g. ‘L3e-A2’ for a medium-performance motorcycle.
For externally chargeable hybrid electric vehicles, the “weighted, combined” values for CO2, fuel consumption and electric energy consumption shall be indicated.
Only applicable for vehicle category L3e.’