1 ANNEX, Regulation (EU) 2016/1825

In forcesince 6 Sep 2016

Implementing Regulation (EU) No 901/2014 is amended as follows:

(1)

Annex I is amended as follows:

(a)

in the list of Appendices, each of the following rows is inserted following their numerical order:

‘5a | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a maximum torque and a maximum net power of a propulsion unit system |

8a | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of audible warning devices system |

9a | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of glazing, windscreen wipers and defrosting and demisting devices system |

9b | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an identification of controls, tell-tales and indicators system |

11a | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a safety belt anchorages system |

11b | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a steer-ability, cornering properties and turn ability system |

13a | Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a vehicle occupant protection, including interior fittings, head restraint and vehicle doors system |

20a | Model information document relating to EU type-approval of a fuel tank as a STU’ |

(b)

in Part B, in point 2.2., in Table 1, in LIST I, the following row is inserted following its numerical order:

‘5a | System: maximum torque and a maximum net power of a propulsion unit |

X

Appendix 2’

(c)

in Part B, in point 2.2., in Table 1, in LIST II, each of the following rows is inserted following their numerical order:

‘8a | System: installation of audible warning devices | II |

9a | System: installation of glazing, windscreen wipers and defrosting and demisting devices | VII |

9b | System: identification of controls, tell-tales and indicators | VIII |

11a | System: safety belt anchorages | XII |

11b | System: steer-ability, cornering properties and turn ability | XIV |

13a | System: vehicle occupant protection, including interior fittings, head restraint and vehicle doors | XVII’ |

(d)

in Part B, in point 2.2., in Table 1, in LIST III, each of the following rows is inserted following their numerical order:

‘20a | STU: fuel tank | IX’ |

(e)

in Part B, in point 2.8., the table relating to information document data entries is amended as follows:

(i)

the following information document data entry 3.3.3.4. is inserted:

‘3.3.3.4. | L1e — L7e | 15/30(4) minutes power(27): …kW’

(ii)

the information document data entry 3.5.4. is replaced by the following:

L1e — L7e | Overview gear ratios

Gear(24) | Internal transmission ratios (ratios of engine to transmission output shaft revolutions) | Final drive ratio(s) (ratio of transmission output shaft to driven wheel revolutions) | Total gear ratios | Ratio (engine speed/vehicle speed) for manual transmission only

1

2

3

…

Reverse’ | | | |

(iii)

the information document data entry 4.0.1. is replaced by the following:

‘4.0.1. | L1e — L7e | Environmental step: Euro …(3/4/5) (4)’

(iv)

the following information document data entries 4.0.2. to 4.0.5. are inserted:

‘4.0.2. | L1e — L7e | Fuel consumption (provide details for each reference fuel tested) …l/kg(4)/100 km

4.0.3. | L1e — L7e | CO2 emissions(25): …g/km

4.0.4. | L1e — L7e | Energy consumption(25): …Wh/km

4.0.5. | L1e — L7e | Electric range(25): …km’

(f)

Appendix 3 is amended as follows:

(i)

the information document data entry 4.0.1. is replaced by the following:

‘4.0.1. | L1e — L7e | Environmental step: Euro …(3/4/5) (4)’

(ii)

the following information document data entries 4.0.2. to 4.0.5. are inserted:

‘4.0.2. | L1e — L7e | Fuel consumption (provide details for each reference fuel tested) …l/kg(4)/100 km

4.0.3. | L1e — L7e | CO2 emissions(25): …g/km

4.0.4. | L1e — L7e | Energy consumption(25): …Wh/km

4.0.5. | L1e — L7e | Electric range(25): …km’

(g)

Appendix 4 is amended as follows:

(i)

the information document data entries 4.0.2., 4.0.2.1. and 4.0.2.2. are deleted;

(ii)

the following information document data entries 4.0.6. and 4.0.6.1. are inserted:

‘4.0.6. | Sound level

4.0.6.1. | L3e | Limit value for Lurban(16): …dB(A)’;

(h)

the following Appendix 5a is inserted:

(i)

Appendix 6 is amended as follows:

(i)

the information document data entry 4.0.1. is replaced by the following:

‘4.0.1. | L1e — L7e | Environmental step: Euro …(3/4/5) (4)’

(ii)

the following information document data entries 4.0.2. to 4.0.5. are inserted:

‘4.0.2. | L1e — L7e | Fuel consumption (provide details for each reference fuel tested) …l/kg(4)/100 km

4.0.3. | L1e — L7e | CO2 emissions(25): …g/km

4.0.4. | L1e — L7e | Energy consumption(25): …Wh/km

4.0.5. | L1e — L7e | Electric range(25): …km’

(j)

Appendix 7 is amended as follows:

(i)

the information document data entries 4.0.1. and 4.0.2. are replaced by the following:

‘4.0.1. | L1e — L7e | Environmental step: Euro …(3/4/5) (4)

4.0.2. | L1e — L7e | Fuel consumption (provide details for each reference fuel tested) …l/kg(4)/100 km’

(ii)

the information document data entries 4.0.2.1. and 4.0.2.2. are deleted;

(iii)

the following information document data entries 4.0.3. to 4.0.6.1. are inserted:

‘4.0.3. | L1e — L7e | CO2 emissions(25): …g/km

4.0.4. | L1e — L7e | Energy consumption(25): …Wh/km

4.0.5. | L1e — L7e | Electric range(25): …km

4.0.6. | | Sound level

4.0.6.1. | L3e | Limit value for Lurban(16): …dB(A)’

(k)

Appendix 8 is amended as follows:

(i)

the information document data entries 4.0.1. and 4.0.2. are replaced by the following:

‘4.0.1. | L1e — L7e | Environmental step: Euro …(3/4/5) (4)

4.0.2. | L1e — L7e | Fuel consumption (provide details for each reference fuel tested) …l/kg(4)/100 km’

(ii)

the information document data entries 4.0.2.1. and 4.0.2.2. are deleted;

(iii)

the following information document data entries 4.0.3. to 4.0.6.1. are inserted:

‘4.0.3. | L1e — L7e | CO2 emissions(25): …g/km

4.0.4. | L1e — L7e | Energy consumption(25): …Wh/km

4.0.5. | L1e — L7e | Electric range(25): …km

4.0.6. | | Sound level

4.0.6.1. | L3e | Limit value for Lurban(16): …dB(A)’;

(l)

the following Appendix 8a is inserted:

(m)

the following Appendix 9a is inserted:

(n)

the following Appendix 9b is inserted:

(o)

the following Appendix 11a is inserted:

(p)

the following Appendix 11b is inserted:

(q)

the following Appendix 13a is inserted:

(r)

the following Appendix 20a is inserted:

(s)

Appendix 24 is replaced by the following:

(t)

the explanatory notes relating to Annex I are amended as follows:

(i)

explanatory note (16) is replaced by the following:

‘(16) Rounded to the nearest whole number for dB(A).’;

(ii)

explanatory note (24) is replaced by the following:

‘(24) For vehicles equipped with CVT indicate the following: 1 “gear ratio at maximum design vehicle speed”; 2 “gear ratio at maximum peak power”; 3 “gear ration at maximum peak torque”. The gear ratios shall include the gear ratio of the primary transmission ratio (if applicable) and be supplemented with an acceptable tolerance band to the satisfaction of the approval authority. For wheel hub engines without gear drive, indicate “n/a” or “1”.’.

(2)

Annex IV is amended as follows:

(a)

Appendix 1 is amended as follows:

(i)

in MODEL A — Section 1, the words ‘conforms in all respects to the type described in EU type-approval (… type-approval number including extension number) issued on ( …date of issue) and’ are replaced by the words ‘conforms in all respects to the type described in EU type-approval (… type-approval number including extension number) (CV*… type-approval number including extension number)(3i) issued on ( …date of issue) (CV* …date of issue)(3i) and’;

(ii)

in MODEL B — Section 1, the words ‘conforms in all respects to the type described in EU type-approval (… type-approval number including extension number) issued on ( …date of issue) and’ are replaced by the words ‘conforms in all respects to the type described in EU type-approval (… type-approval number including extension number) (CV*… type-approval number including extension number)(3i) issued on ( …date of issue) (CV* …date of issue)(3i) and’;

(iii)

in MODEL C — Section 1, the words ‘conforms in all respects to the type described in EU type-approval (… type-approval number including extension number) issued on ( …date of issue) and’ are replaced by the words ‘conforms in all respects to the type described in EU type-approval (… type-approval number including extension number) (CV*… type-approval number including extension number)(3i) issued on ( …date of issue) (CV* …date of issue)(3i) and’;

(iv)

in Section 2, the heading ‘Section 2’ is replaced by the following:

(v)

in Section 2, entry 4.0.1. is replaced by the following:

‘4.0.1. | Environmental step: Euro …(3/4/5) (1)’

(vi)

in Section 2, entries 4.0.2., 4.0.2.1. and 4.0.2.2. are deleted;

(vii)

in Section 2, the following entries 4.0.6. to 4.0.6.3. are inserted after entry 4.0.1.:

‘4.0.6. | Sound level measured according to(m):

4.0.6.1. | Stationary: …dB(A) (CV*: …dB(A))(3i) at engine speed: …min-1 (CV*: …min-1)(3i)

4.0.6.2. | Drive-by: …dB(A) (CV*: …dB(A))(3i)

4.0.6.3. | Limit value for Lurban(3r): …dB(A) (CV*: …dB(A))(3i)’;

(viii)

in Section 2, entry 3.2.15.1. is replaced by the following:

‘3.2.15.1. | Type I test: tailpipe emissions after cold start, including the deterioration factor, if applicable:

CO: | mg/km | (CV*:… mg/km)(3i)

THC: | mg/km | (CV*:… mg/km)(3i)

NMHC: | mg/km (3) | (CV*:… mg/km)(3i)

NOx: | mg/km | (CV*:… mg/km)(3i)

THC+NOx: | mg/km(3) | (CV*:… mg/km)(3i)

PM: | mg/km(3) | (CV*:… mg/km)(3i)’

(ix)

in Section 2, the heading ‘Energy efficiency’, including all its entries, is replaced by the following:

‘Energy efficiency(m)(o):

4.0.2. | Fuel consumption(3)(q): | l or kg/100 km | (CV*:… l or kg/100 km)(3)(q)(3i)

4.0.3. | CO2 emissions(3)(q)(n): | g/km | (CV*:… g/km)(3)(q)(3i)

4.0.4. | Energy consumption(3)(q): | Wh/km | (CV*:… Wh/km)(3)(q)(3i)

4.0.5. | Electric range(3): | km | (CV*:… km)(3)(3i)’

(b)

Appendix 2 is amended as follows:

(i)

entry 0.3. is replaced by the following:

‘0.3. | Category, subcategory and sub-subcategory of vehicle(6)(u):…’

(ii)

the heading ‘Energy efficiency’, including all its entries, is replaced by the following:

‘Energy efficiency:

4.0.2. | Fuel consumption(3)(q): | l or kg/100 km | (CV*:… l or kg/100 km)(3)(q)(3i)

4.0.3. | CO2 emissions(3)(q)(n): | g/km | (CV*:… g/km)(3)(q)(3i)

4.0.4. | Energy consumption(3)(q): | Wh/km | (CV*:… Wh/km)(3)(q)(3i)

4.0.5. | Electric range(3): | km | (CV*:… km)(3)(3i)’

(c)

the explanatory notes relating to Annex IV are amended as follows:

(i)

explanatory note (9) is replaced by the following:

‘(9) Indicate the following value according to the category of the vehicle:

for (sub) categories: L1e, L2e, L6e, L7e-B1, L7e-C: the measured maximum speed of the vehicle;

for (sub) categories L3e, L4e, L5e, L7e-A and L7e-B2: the maximum design vehicle speed.

for cycles designed to pedal (L1e): suppress this entry of the certificate of conformity’;

(ii)

explanatory note (n) is deleted;

(iii)

explanatory note (o) is replaced by the following:

‘(o) Round the values to the nearest whole number for dB(A), Wh/ km, mg/ km, g/km, ppm, mm, kg, km and km/ h; to the nearest tenth for kW, l/ 100 km, kg/ 100 km, m3/ 100 km and for % vol; and to the nearest hundredth for kW/ kg and for m-1.’;

(iv)

explanatory note (p) is deleted;

(v)

the second explanatory note (s) below explanatory note (t) is deleted;

(vi)

the following explanatory note (u) is inserted:

‘(u) The information contained in this entry shall be stated in entry No 04. “Vehicle category” of the certificates of conformity issued in accordance with the template set out in Annex IV to Directive 2002/24/EC.’;

(vii)

the following explanatory note (3r) is inserted:

‘(3r) Only applicable for vehicle category L3e’.

(3)

Annex V is amended as follows:

(a)

point 3.1.6. is replaced by the following:

‘3.1.6. The existence of measures taken by the manufacturer to ensure the traceability of the vehicle referred to in point 3.1.5. needs not be checked at the time of the type-approval.’;

(b)

point 3.2.8. is replaced by the following:

‘3.2.8. The vehicle identification number shall, if possible, be presented on a single line. When the VIN is marked on two lines, the beginning and the end of the VIN shall be limited by one symbol at the choice of the manufacturer which should neither be a Roman capital letter nor an Arabic numeral.’

(c)

in Appendix 1, point 5 is replaced by the following:

‘5. Example for a L3e-A3 motorcycle with additional information for the converted vehicle (CV), a L3e-A2 motorcycle, outside the clearly marked rectangle. In this case for the purpose of a temporary and reversible manufacturer's authorised modification to the first registered L3e-A3 motorcycle in order to register it nationally after its conversion as a reduced-power L3e-A2 configuration (e.g. for vehicle operators with A2 driving licence):

MOTORUDOLPH

L3e-A3

e4*168/2013*2691

JRM00DBP008002211

84 dB(A) — 4250 min-1

max 352 kg

L3e-A2

e4*168/2013*2692

83 dB(A) — 3750 min-1

35 kW’.

(4)

Annex VI is amended as follows:

(a)

in Appendix 1, in Section III, entry 2.1. is replaced by the following:

‘2.1. | The approval is granted in accordance with Article 40 of Regulation (EU) No 168/2013 and the validity of the approval is thus limited to dd/mm/yyyy(6).’

(b)

Appendix 2 is amended as follows:

(i)

in Section III, entry 4.1. is replaced by the following:

‘4.1. | The approval is granted in accordance with Article 40 of Regulation (EU) No 168/2013 and the validity of the approval is thus limited to dd/mm/yyyy(6).’

(ii)

in Section III, the first indent under ‘NB:’ is replaced by the following:

‘— If this model is used for type-approval of a vehicle as an exemption for new technology or new concept, pursuant to Article 40 of Regulation (EU) No 168/2013, the heading of the certificate shall read ‘EU WHOLE-VEHICLE PROVISIONAL TYPE-APPROVAL CERTIFICATE VALID ONLY ON THE TERRITORY OF …(5)’. The provisional type-approval certificate shall also specify the restrictions that have been imposed as to its validity and the waivers which have been applied in accordance with Article 30(4) of Regulation (EU) No 168/2013.’

(iii)

the explanatory notes related to Appendix 2 are replaced by the following:

(1)

Delete where not applicable.

(2)

Indicate the alphanumeric code Type-Variant-Version or ‘TVV’ allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I.

(3)

Classified according to Article 4 of and Annex I to Regulation (EU) No 168/2013, the coding shall be indicated, e.g. ‘L3e-A1E’ for a low-performance Enduro motor-cycle.

(4)

See section 2.

(5)

Indicate the Member State.

(6)

Applicable only for type-approval of a vehicle as an exemption for new technology or new concept, pursuant to Article 40 of Regulation (EU) No 168/2013.

(7)

Applicable only for vehicle type-approval for a national small series, pursuant to Article 42 of Regulation (EU) No 168/2013.

(8)

Indicate only the latest amendment in case of an amendment of one or more Articles of Regulation (EU) 168/2013, according to the amendment applied for the EU type-approval.’;

(c)

in Appendix 4, in Section II, the following entries 4a. and 4a.1. are inserted before entry 5.:

‘4a. | The approval is granted/extended/refused/withdrawn(1)

4a.1. | The approval is granted in accordance with Article 40 of Regulation (EU) No 168/2013 and its validity is thus limited to dd/mm/yyyy(5).’

(d)

Section II of Appendix 5 is amended as follows:

(i)

the following entries 4a. and 4a.1. are inserted before entry 5.:

‘4a. | The approval is granted/extended/refused/withdrawn(1)

4a.1. | The approval is granted in accordance with Article 40 of Regulation (EU) No 168/2013 and its validity is thus limited to dd/mm/yyyy(5).’

(ii)

entry 5. is replaced by the following:

‘5. | Restrictions of validity(1)(5): …’

(iii)

entry 6. is replaced by the following:

‘6. | Waivers applied(1)(5): …’

(5)

Annex VII is amended as follows:

(a)

in point 4., table 1 is deleted;

(b)

point 5. is replaced by the following:

LIST I — Environmental and propulsion unit performance requirements

System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) No | alphanumerical character

System: engine emissions (Euro 4 stage) | 134/2014 | A1

System: engine emissions (Euro 5 stage) | 134/2014 | A2

System: crankcase (point 1.3.1. and 1.3.2.) and evaporative emissions (point 1.4.1. to 1.4.3 of Annex IV to Regulation (EU) 168/2013) | 134/2014 | B1

System: crankcase (point 1.3.1. and 1.3.2.) and evaporative emissions (point 1.4.4. to 1.4.6 of Annex IV to Regulation (EU) 168/2013) | 134/2014 | B2

System: crankcase (point 1.3.1. and 1.3.2.) and evaporative emissions (point 1.4.7. to 1.4.8 of Annex IV to Regulation (EU) 168/2013) | 134/2014 | B3

System: environmental on-board diagnostic (OBD Stage I: point 1.8.1. to 1.8.2 of Annex IV to Regulation (EU) 168/2013) | 134/2014 | C1

System: environmental on-board diagnostic (OBD Stage II: point 1.8.3. of Annex IV to Regulation (EU) 168/2013) | 134/2014 | C2

System: sound level | 134/2014 | D

System: propulsion unit performance | 134/2014 | E

System: maximum torque and a maximum net power of a propulsion unit | 134/2014 | E1

STU: pollution-control device | 134/2014 | F

STU: noise-abatement device | 134/2014 | G

STU: exhaust device (pollution-control device and noise-abatement device) | 134/2014 | H

LIST II — Vehicle functional safety requirements

System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) No | alphanumerical character

System: braking | 3/2014 | J

System: installation of lighting and light-signalling devices | 3/2014 | K

System: roll-over protective structure (ROPS) | 3/2014 | L

System: installation of tyres | 3/2014 | M

System: installation of audible warning devices | 3/2014 | AA

System: installation of glazing, windscreen wipers and defrosting and demisting devices | 3/2014 | AB

System: identification of controls, tell-tales and indicators | 3/2014 | AC

System: safety belt anchorages | 3/2014 | AD

System: steer-ability, cornering properties and turn ability | 3/2014 | AE

System: vehicle occupant protection, including interior fittings, head restraint and vehicle doors | 3/2014 | AF

Component/STU: audible warning device | 3/2014 | N

Component/STU: non-glazing front windscreen | 3/2014 | O

Component/STU: windscreen washer device | 3/2014 | P

Component/STU: rearward visibility device | 3/2014 | Q

Component/STU: safety belts | 3/2014 | R

Component/STU: seating position (saddle/seat) | 3/2014 | S

LIST III — Vehicle construction and general type-approval requirements

System or component/separate technical unit (STU) | Commission Delegated Regulation (EU) No | alphanumerical character

System: functional on-board diagnostics (OBD Stage I: point 1.8.1. to 1.8.2 of Annex IV to Regulation (EU) 168/2013) | 44/2014 | T1

System: functional on-board diagnostics (OBD Stage II: point 1.8.3. of Annex IV to Regulation (EU) 168/2013) | 44/2014 | T2

STU: trailer coupling device | 44/2014 | U

STU: devices to prevent unauthorised use | 44/2014 | V

STU: passenger handholds | 44/2014 | W

STU: footrests | 44/2014 | X

STU: side-car | 44/2014 | Y

STU: fuel tank | 44/2014 | Z’

(6)

Annex VIII is amended as follows:

(a)

item 2.2.1.3.3. is replaced by the following:

‘2.2.1.3.3.

Type II test results(3):

Test | HC (ppm) |

CO

(% vol.)

Lambda | Engine speed (min-) | Engine oil temperature (K) |

Measured & corrected value of absorption coefficient

(m-1)

PI: Low idle test | | | | | | —

PI: High idle test | | | | | | —

CI — Free acceleration test / Smoke opacity test results | — | — | — | — | — | ’

(b)

items 2.2.1.8.6. and 2.2.1.8.7. are replaced by the following:

[Where applicable.] [Round to 2 decimal places.] [Round to 4 decimal places.] [Round to 0 decimal places] [Set Ki = 1 in case: (a) the vehicle is not equipped with a periodically regenerating emission abatement system or; (b) the vehicle is not a hybrid electric vehicle.]

Test Type VII Test Results (TRTTVII) | Test No |

CO2

(g/km)

Fuel consumption

(l/100km) or (kg/100 km)

TRTTI Measured x | 1 | |

2 | |

3 | |

TRTTI Measured Mean | | |

Ki

(no unit )

TRTTVIIx =

Ki · TRTTI Measured x Mean

CO2 and Fuel consumption as declared by the manufacturer | — | |

Electric energy consumption and electric range(3):

Measured electric energy consumption

(Wh/km)

Declared electric energy consumption

(Wh/km)

Measured electric range

(km)

Declared electric range

(km)

Pure electric powertrain | | | |

NOVC hybrid electric powertrain | | | | ’;

(c)

in point 2.2.1.10.9., Table 5-13 is replaced by the following:

Sound emission level | Euro 4 | Euro 5

Sound level limits | Annex VI(D) to Regulation (EU) No 168/2013 | Equivalent UNECE sound level limits to Annex VI(D) to Regulation (EU) No 168/2013 | Annex VI(D) to Regulation (EU) No 168/2013

Test requirements | Annex VIII to Regulation (EU) No 168/2013 | UNECE Regulations referred to in Annex VI(D) to Regulation (EU) No 168/2013 | UNECE Regulations referred to in Annex VI(D) to Regulation (EU) No 168/2013

Administrative requirements for vehicle subcategories regarding sound level:

Vehicle (sub)categories | |

L1e, L6e-A | Annex I to UNECE Regulation No 63 | UNECE Regulation No 63

L3e | Annex I to UNECE Regulation No 41 | UNECE Regulation No 41

L2e, L4e, L5e, L6e-B, L7e | Annex I to UNECE Regulation No 9 | UNECE Regulation No 9

Replacement exhaust noise-abatement devices all categories | Annex I to UNECE Regulation No 92 | UNECE Regulation No 92’

(d)

in point 2.2.1.10.11., Table 5-14 is replaced by the following:

Vehicle category | Propulsion class |

Euro 4 sound level limit

SLEU4 (dB(A)) / Euro 4 test results TRTTIXEU4 (dB(A))& (% of SLEU4)

Euro 4 sound test procedure |

Euro 5 sound level limit

SLEU5 (dB(A)) / Euro 5 test results TRTTIXEU5 (dB(A)) & (% of SLEU5)

Euro 5 sound test procedure

L1e-A | PI / CI / Hybrid | SLEU4:63 | Commission Delegated Regulation (EU) No 134/2014 Annex VIII / UNECE Regulation No 63 | SLEU5: | UNECE Regulation No 63

TRTTIXEU4: | TRTTIXEU5:

L1e-B |

PI / CI / Hybrid

vmax ≤ 25 km/h

SLEU4:66 | SLEU5:

TRTTIXEU4: | TRTTIXEU5:

PI / CI / Hybrid

vmax ≤ 45 km/h

SLEU4:71 | SLEU5:

TRTTIXEU4: | TRTTIXEU5:

This article is long: the rest is at the official publication.