For the purposes of this Annex:
1.1. ‘axle group’ means multiple axles where the axle spread between one axle and its adjacent axle is equal to or less than 2,0 m. Where the axle spread between one axle and its adjacent axle is greater than 2,0 m, each individual axle shall be considered as an independent axle group.
1.2. ‘adhesion utilization curve’ means the characteristic curve of the braking force ratio without rolling resistance and normal reaction of road surface on a given axle under braking plotted against the braking rate of the vehicle.
The maximum design speed is considered, throughout this Annex, to be in the forward direction of the vehicle travel, unless otherwise explicitly mentioned.
2.1.1.
The performance prescribed for braking systems shall be based on the stopping distance and the mean fully developed deceleration or only on one of those two quantities. The performance of a braking system shall be determined by measuring the stopping distance in relation to the initial speed of the vehicle and by measuring the mean fully developed deceleration during the test or only on one of those two quantities. Both stopping distance and mean fully developed deceleration or only one of them shall be prescribed and measured, following to the test to be performed.
2.1.2.
The stopping distance shall be the distance covered by the vehicle from the moment when the driver begins to actuate the control device of the braking system until the moment when the vehicle stops; the initial vehicle speed (v1) shall be the speed at the moment when the driver begins to actuate the control device of the braking system; the initial speed shall not be less than 98 % of the prescribed speed for the test in question. The mean fully developed deceleration dm shall be calculated as the deceleration averaged with respect to distance over the interval vb to ve according to the following formula:
dm
v2bv2e
25,92 sesbms2
Where:
v1initial vehicle speed calculated as described in the first subparagraph
vbvehicle speed at 0,8 v1 in km/h
vevehicle speed at 0,1 v1 in km/h
sbdistance travelled between v1 and vb in metres
sedistance travelled between v1 and ve in metres
The speed and distance shall be determined using instrumentation having an accuracy of ± 1 % at the prescribed speed for the test. The dm may be determined by other methods than the measurement of speed and distance; in this case, the accuracy of the dm shall be within ± 3 %.
2.1.3.
For the type-approval of any vehicle, the braking performance shall be measured during road tests conducted in the following conditions:
2.1.3.1. The vehicle's condition as regards mass shall be as prescribed for each type of test and be specified in the test report.
2.1.3.2. The test shall be carried out at the speeds prescribed for each type of test; if the maximum design speed of a vehicle is lower than the speed prescribed for a test, the test shall be performed at the vehicle's maximum design speed.
2.1.3.3. During the tests, the force applied to the control device of the braking system in order to obtain the prescribed performance shall not exceed 600 N on the foot or 400 N on the hand operated control devices.
2.1.3.4. The road shall have a surface affording good adhesion, unless specified otherwise.
2.1.3.5. The tests shall be performed when there is no wind liable to affect the results.
2.1.3.6. At the start of the tests the tyres shall be cold and at the pressure prescribed for the load actually borne by the wheels when the vehicle is stationary.
2.1.3.7. The prescribed performance shall be obtained without deviation of the vehicle from its course, without abnormal vibrations and without wheel-locking. Wheel-locking is permitted where specifically mentioned.
2.1.4.1.
In braking tests, and in particular in those at high speed, the general behaviour of the vehicle during braking shall be checked.
2.1.4.2.
Behaviour of the vehicle during braking on a road on which adhesion is reduced.
The behaviour of vehicles of categories Tb, R2b, R3b, R4b and S2b on a road on which adhesion is reduced, shall meet the relevant requirements of Appendix 1 of this Annex or, if the vehicle is equipped with ABS, the requirements of Annex XI.
2.2.1.1.
The brake shall be cold. A brake is deemed to be cold when one of the following conditions is met:
2.2.1.1.1. The temperature measured on the disc or on the outside of the drum is below 100 °C.
2.2.1.1.2. In the case of totally enclosed brakes, including oil immersed brakes, the temperature measured on the outside of the housing is below 50 °C.
2.2.1.1.3. The brakes have not been used for one hour before the test.
2.2.1.2.
During the braking test, an axle without a brake, when this axle is capable of being declutched, shall not be connected with a braked axle. However, in case of tractors with one braked axle and an automatic engagement of the drive to all other axles during braking, all wheels are deemed to be braked.
2.2.1.3.
The test shall be conducted under the following conditions:
2.2.1.3.1. The vehicle shall be laden to its maximum permissible mass specified by the manufacturer and with an unbraked axle loaded to its maximum permissible mass. The braked axle wheels shall be fitted with the largest diameter tyres intended by the manufacturer for that vehicle type when carrying the maximum permissible mass. For vehicles braking on all wheels, the front axle shall be laden to its maximum permissible mass.
2.2.1.3.2. The test shall be repeated on an unladen vehicle; in case of tractors, carrying only the driver and if necessary a person responsible for monitoring the results of the test.
2.2.1.3.3. The limits prescribed for minimum performance, both for tests with the vehicle unladen and for tests with the vehicle laden, are those laid down hereunder for each category of vehicle, the vehicle shall satisfy both the prescribed stopping distance and the prescribed mean fully developed deceleration for the relevant vehicle category, but it may not be necessary to actually measure both parameters.
2.2.1.3.4. The road shall be level.
2.2.2.1.
The test shall be carried out at the maximum design speed of the vehicle, with the engine disconnected. This speed may be subject to a certain margin of tolerance. However, in any case the minimum prescribed performance shall be attained. The prescribed maximum stopping distance (by the stopping distance formula) shall be calculated with the actual test speed.
2.2.2.2.
To check compliance with the requirements of point 2.2.1.2.4 of Annex I, a Type-0 test shall be carried out with the engine disconnected at the initial speed of 30 km/h.
On application of the control of the parking brake system, the mean fully developed deceleration and the deceleration immediately before the vehicle stops shall not be less than 1,5 m/s2. The same requirement applies in case of auxiliary control mentioned in point 2.2.1.2.4 of Annex I.
The test shall be carried out with the laden vehicle. The force exerted on the braking control device shall not exceed the specified values.
2.2.2.3.
In the case of vehicles equipped with handlebar and straddle seat or equipped with steering wheel and bench seat or bucket seats in one or more rows, that are also equipped with non-disengageable transmission, as this can be proved by the manufacturer at the braking testing, the vehicle shall complete the Type-0 test with the engine connected.
2.2.3.1.
The braking performance of the towed vehicle can be calculated either from the braking rate of the tractor plus the towed vehicle and the measured thrust on the coupling or, in certain cases, from the braking rate of the tractor plus the towed vehicle with only the towed vehicle being braked. The engine of the tractor shall be disconnected during the braking test.
2.2.3.2.
If the towed vehicle is fitted with a compressed-air braking system, the pressure in the supply line shall not exceed 700 kPa during the brake test and the signal value in the control line shall not exceed the following values, depending on the installation:
2.2.3.2.1. 650 kPa in the pneumatic control line;
2.2.3.2.2. A digital demand value corresponding to 650 kPa (as defined in ISO 11992:2003 including ISO 11992-2:2003 and its Amd.1:2007 in the electric control line.
2.2.3.3.
If the towed vehicle is fitted with a hydraulic braking system:
2.2.3.3.1. The prescribed minimum braking performance shall be achieved with a pressure at the coupling head of the control line not exceeding 11500 kPa
2.2.3.3.2. The maximum pressure delivered at the coupling head of the control line shall not exceed 15000 kPa.
2.2.3.4.
With the exception of cases according to points 2.2.3.5 and 2.2.3.6, it is necessary for the determination of the braking rate of the towed vehicle to measure the braking rate of the tractor plus the towed vehicle and the thrust on the coupling. The tractor shall meet the requirements laid down in Appendix 1 with regard to the relation between the ratio TM/FM and the pressure pm,
where:
TMsum of braking forces at the periphery of all wheels of tractors
FMtotal normal static reaction of road surface on wheels of tractors
pmpressure at coupling head of control line
The braking rate of the towed vehicle shall be calculated according to the following formula:
zR = zR + M + D/FR
Where:
zRbraking rate of the towed vehicle
zR + Mbraking rate of the tractor plus the towed vehicle
Dthrust on the coupling (tractive force D > 0; compressive force D < 0)
FRtotal normal static reaction of road surface on all wheels of towed vehicle
2.2.3.5.
If a towed vehicle has a continuous or semi-continuous braking system where the pressure in the brake actuators does not change during braking despite the dynamic axle load shifting, the towed vehicle alone may be braked. The braking rate zR of the towed vehicle shall be calculated according to the following formula:
zRzRMRFMFRFRR
Where:
R
rolling resistance value:
0,02 in the case of vehicles with a maximum design speed not exceeding 40 km/h
0,01 in the case of vehicles with a maximum design speed exceeding 40 km/h
FMtotal normal static reaction of road surface on wheels of tractors
FRtotal normal static reaction of road surface on all wheels of towed vehicle
2.2.3.6.
Alternatively, the evaluation of the braking rate of the towed vehicle may be done by braking the towed vehicle alone. In this case the pressure used shall be the same as that measured in the brake actuators during the braking of the combination.
This test type shall be performed according to the requirements of points 2.3.1 or 2.3.2, as applicable.
Tractors of categories T and C shall undergo the Type-I test with repeated braking.
2.3.1.1.
The service braking system of tractors covered by this Regulation shall be tested by successively applying and releasing the brakes a number of times. The vehicle shall be fully laden and tested in accordance with the conditions shown in the following table:
Vehicle category | Conditions
v1 [km/h] | v2 [km/h] | Δt [sec] | n
T, C | 80 % vmax | ½ v1 | 60 | 20
Where
v1speed at start of braking
v2speed at end of braking
vmaxmaximum design speed of vehicle
nnumber of brake applications
Δtduration of the braking cycle (time elapsing between the initiation of one brake application and the initiation of the next).
2.3.1.1.1.
In the case of tractors with a maximum design speed not exceeding 40 km/h, as an alternative to the test conditions as shown in the table of point 2.3.1.1 the conditions shown in the following table may be applied:
Vehicle category | Conditions
v1 [km/h] | v2 [km/h] | Δt [sec] | n
T, C | 80 % vmax | 0,05 v1 | 60 | 18
2.3.1.2.
If the characteristics of the vehicle do not allow for the period of time prescribed for Δt, the duration may be increased; in any event, in addition to the time necessary for braking and accelerating the vehicle, a period of 10 seconds shall be allowed in each cycle for stabilising the speed v1.
2.3.1.3.
In these tests, the force applied to the control device shall be so adjusted as to attain a mean fully developed deceleration of 3 m/s2 at the first application of the brakes. This force shall remain constant throughout the succeeding brake applications.
2.3.1.4.
During brake applications the highest gear ratio (excluding overdrive, etc.) shall be continuously engaged. As an alternative, it is also allowed to perform the test with the engine disconnected, where applicable, during brake applications.
2.3.1.5.
For regaining speed after braking, the gearbox shall be used in such a way as to attain the speed v1 in the shortest possible time (maximum acceleration allowed by the engine and gearbox).
2.3.1.6.
In the case of vehicles equipped with automatic brake adjustment devices the adjustment of the brakes shall, prior to the type-I test above, be set according to the following procedures as appropriate:
2.3.1.6.1. In the case of vehicles equipped with air operated brakes the adjustment of the brakes shall be such as to enable the automatic brake adjustment device to function. For this purpose the actuator stroke shall be adjusted to:
so ≥ 1,1 × sre-adjust
(the upper limit shall not exceed a value recommended by the manufacturer)
Where:
Sre-adjust
is the re-adjustment stroke according to the specification of the manufacturer of the automatic brake adjustment device, i.e. the stroke, where it starts to readjust the running clearance of the brake with an actuator pressure of 15 per cent of the brake system operating pressure but not less than 100 kPa.
Where, by agreement with the technical service, it is impractical to measure the actuator stroke, the initial setting shall be agreed with the technical service.
From the above condition the brake shall be operated with an actuator pressure of 30 % of the brake system operating pressure but not less than 200 kPa 50 times in succession. This shall be followed by a single brake application with an actuator pressure of > 650 kPa.
2.3.1.6.2. In the case of vehicles equipped with hydraulically operated disc brakes no setting requirements are deemed necessary.
2.3.1.6.3. In the case of vehicles equipped with hydraulically operated drum brakes the adjustment of the brakes shall be as specified by the manufacturer.
2.3.2.1.
The service braking system of vehicles of categories R1, R2, S1, R3a, R4a and S2a; and of vehicles of categories R3b and S2b, where the sum of the technically permissible masses per axle does not exceed 10000 kg, shall be tested in such a manner that, the vehicle being laden, the energy input to the brakes is equivalent to that recorded in the same period of time when the laden vehicle being tested is driven at a steady speed of 40 km/h on a 7 % down-gradient for a distance of 1,7 km.
Alternatively, this requirement is deemed to be fulfilled for vehicles of categories R3a, R4a, S2a and for vehicles of categories R3b and S2b, where the sum of the technically permissible masses per axle does not exceed 10000 kg, when these vehicles have passed the Type-III test according to point 2.5.
2.3.2.2.
The test may be carried out on a level road, the trailed vehicle being towed by an agricultural vehicle; during the test, the force applied to the control device shall be adjusted so as to keep the resistance of the towed vehicle constant (7 % of the maximum stationary axle load of the towed vehicle). If the power available for hauling is insufficient, the test can be conducted at a lower speed but over a greater distance; as shown in the following table:
Speed (km/h) | distance (in m)
40 | 1700
30 | 1950
20 | 2500
15 | 3100
2.3.2.3.
In the case of towed vehicles equipped with automatic brake adjustment devices the adjustment of the brakes shall, prior to the Type-I test prescribed above, be set according to the procedure as laid down in point 2.5.4.
2.3.3.1.
At the end of the type-I test (test described in point 2.3.1 or test described in point 2.3.2) the hot performance of the service braking system shall be measured in the same conditions (and in particular at a constant control force no greater than the mean force actually used) as for the type-0 test with the engine disconnected (the temperature conditions may be different).
2.3.3.2.
For tractors this hot performance shall not be less than 80 % of that prescribed for the category in question, nor less than 60 % of the figure recorded in the type-0 test with the engine disconnected.
2.3.3.3.
In the case of towed vehicles, the hot brake force at the periphery of the wheels when tested at 40 km/h shall not be less than 36 % of towed vehicles with vmax > 30 km/h or 26 % of towed vehicles with vmax ≤ 30 km/h of the maximum stationary wheel load, nor less than 60 % of the figure recorded in the type 0 test at the same speed.
In the case of tractors equipped with automatic brake adjustment devices, the brakes after completing the tests described in point 2.3.3 shall be allowed to cool to a temperature representative of a cold brake (i.e. ≤ 100 °C) and it shall be verified that the vehicle is capable of free running by fulfilling one of the following conditions:
2.3.4.1. Wheels are running freely (i.e. may be rotated by hand);
2.3.4.2. It is ascertained that when the vehicle is driven at a constant speed of v = 60 km/h or the maximum design speed of the towed vehicle, whichever is the lower, with the brakes released the asymptotic temperatures shall not exceed a drum/disc temperature increase of 80°C, then the residual brake moments are regarded as acceptable.
In addition to the type-I test, tractors of categories Tb and Cb having a maximum permissible mass exceeding 12 t, shall also undergo the type-II test.
2.4.1.
Laden tractor shall be tested in such a manner that the energy input is equivalent to that recorded in the same period of time with a laden tractor driven at an average speed of 30 km/h on a 6 % down-gradient for a distance of 6 km, with the appropriate gear engaged and the endurance braking system, if the vehicle is equipped with one, being used. The gear engaged shall be such that the speed of the engine (min-1) does not exceed the maximum value prescribed by the manufacturer.
2.4.2.
For vehicles in which the energy is absorbed by the braking action of the engine alone, a tolerance of ± 5 km/h on the average speed shall be permitted, and the gear enabling the speed to be stabilised at the value closest to 30 km/h on the 6 % down-gradient shall be engaged. If the performance of the braking action of the engine alone is determined by a measurement of deceleration, it shall be sufficient if the mean deceleration measured is at least 0,5 m/s2.
2.4.3.
At the end of the test, the hot performance of the service braking system shall be measured in the same conditions as for the type-0 test with the engine disconnected (the temperature conditions may be different). This hot performance shall give a stopping distance not exceeding the following values and a mean fully developed deceleration not less than the following values, using a control force not exceeding 60 daN:
0,15 v + (1,33 v2/115) | (the second term corresponds to a mean fully developed deceleration dm = 3,3 m/s2).
2.5.1.
R3b, R4b, S2b where the sum of the technically permissible masses per axle exceeds 10000 kg
or alternatively of categories
2.5.2.
R3a, R4a, S2a, when these vehicles have not been tested according to point 2.3.2.
2.5.3.
R3b and S2b where the sum of the technically permissible masses per axle does not exceed 10000 kg.
2.5.4.1.
The adjustment of the brakes shall, prior to the type-III test below, be set according to the following procedures as appropriate:
2.5.4.1.1. In the case of towed vehicles equipped with air operated brakes the adjustment of the brakes shall be such as to enable the automatic brake adjustment device to function. For this purpose the actuator stroke shall be adjusted to:
so ≥ 1,1 × sre-adjust
(the upper limit shall not exceed a value recommended by the manufacturer)
Where:
sre-adjustis the re-adjustment stroke according to the specification of the manufacturer of the automatic brake adjustment device, i.e. the stroke, where it starts to readjust the running clearance of the brake with an actuator pressure of 100 kPa.
Where, by agreement with the technical service, it is impractical to measure the actuator stroke, the initial setting shall be agreed with the technical service.
From the above condition the brake shall be operated with an actuator pressure of 200 kPa, 50 times in succession. This shall be followed by a single brake application with an actuator pressure of ≥ 650 kPa.
2.5.4.1.2. In the case of towed vehicles equipped with hydraulically operated disc brakes no setting requirements are deemed necessary.
2.5.4.1.3. In the case of towed vehicles equipped with hydraulically operated drum brakes the adjustment of the brakes shall be as specified by the manufacturer.
2.5.4.2.
For the road test the conditions shall be as follows:
Number of brake applications | 20
Duration of a braking cycle | 60 s
Initial speed at the beginning of braking | 60 km/h
Braking applications | In these tests, the force applied to the control device shall be so adjusted as to attain the mean fully developed deceleration of 3 m/s2 in respect to the towed vehicle mass PR at the first brake application; this force shall remain constant throughout the succeeding brake applications.
The braking rate of a towed vehicle is calculated according to the formula given in point 2.2.3.5:
zRzRMR
FMFR
FRR
The speed at the end of braking:
v2v1FMF1F24FMF1F2
Where:
zRbraking rate of the towed vehicle,
zR + Mbraking rate of the vehicle combination (tractor and towed vehicle),
Rrolling resistance value = 0,01
FMtotal normal static reaction between the road surface and the wheels of tractor (N),
FRtotal normal static reaction between the road surface and the wheels of towed vehicle (N),
F1normal static reaction of the part of the mass of the towed vehicle borne by the unbraked axle(s) (N),
F2normal static reaction of the part of the mass of the towed vehicle borne by the braked axle(s) (N),
PRPR = FR/g
v1initial speed (km/h),
v2final speed (km/h).
At the end of the test according to point 2.5.4, the hot performance of the service braking system shall be measured under the same conditions as for the Type-0 test with, however, different temperature conditions and starting from an initial speed of 60 km/h. The hot brake-force at the periphery of the wheels shall then not be less than 40 % of the maximum stationary wheel load, and not less than 60 per cent of the figure recorded in the Type-0 test at the same speed.
After completing the tests described in point 2.5.5, the brakes shall be allowed to cool to a temperature representative of a cold brake (i.e. < 100 °C) and it shall be verified that the towed vehicle is capable of free running by fulfilling one of the following conditions: