Regulation (EC) No 692/2008 is amended as follows:
in the list of Annexes, the Annex XX is added:
‘ANNEX XXMeasurement of net engine power’;
Annex I is amended as follows:
Point 2.4 is replaced by the following:
2.4.1.
Figure I.2.4 illustrates the application of the tests for type-approval of a vehicle. The specific test procedures are described in Annexes II, III, IV, V, VI, VII, VIII, X, XI, XII, XVI [Specific test procedures for hydrogen and flex fuel biodiesel vehicles will be defined at a later stage.] and XX.
[When a bi-fuel vehicle is combined with a flex fuel vehicle, both test requirements are applicable.] [This provision is temporary, further requirements for biodiesel shall be proposed later on.] [Test on petrol only before the dates set out in Article 10(6) of Regulation (EC) No 715/2007. The test will be performed on both fuels after these dates. The E75 test reference fuel specified in Annex IX, Section B, shall be used.] [Only NOx emissions shall be determined when the vehicle is running on hydrogen.] [Upon the choice of the manufacturer vehicles with positive and compression ignition engines may be tested with either E5 or E10 and either B5 or B7 fuels, respectively. However: Not later than sixteen months after the dates set out in Article 10(4) of Regulation (EC) No 715/2007, new type -approvals shall only be performed with E10 and B7 fuels, Not later than three years after the dates set out in Article 10(5) of Regulation (EC) No 715/2007, all new vehicles shall be type-approved with E10 and B7 fuels.’]
Vehicle category | Vehicles with positive ignition engines including hybrids | Vehicles with compression ignition engines including hybrids | Pure electric vehicles | Hydrogen Fuel cell vehicles
Mono fuel | Bi-fuel | Flex-fuel | Flex fuel | Mono fuel
Reference fuel |
Petrol
(E5/E10)
LPG | NG/Biome thane | Hydrogen | Petrol (E5/E10) | Petrol (E5/E10) | Petrol (E5/E10) | Petrol (E5/E10) | NG/Biomethane |
Diesel
(B5/B7)
Diesel
(B5/B7)
| —
LPG | NG/Biomethane | Hydrogen |
Ethanol
(E85)
H2NG | Biodiesel
Gaseous pollutants
(Type 1 test)
Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes (B5/B7 only) | Yes | — | —
Particulate mass and particulate number
(Type 1 test)
Yes | — | — | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(both fuels)
| Yes (B5/B7 only) | Yes | — | —
Idle emissions
(Type 2 test)
Yes | Yes | Yes | — |
Yes
(both fuels)
Yes
(both fuels)
Yes
(petrol only)
Yes
(both fuels)
Yes
(NG/biomethane only)
| — | — | —
Crankcase emissions
(Type 3 test)
Yes | Yes | Yes | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(NG/biomethane only)
| — | — | —
Evaporative emissions
(Type 4 test)
Yes | — | — | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
| — | — | — | —
Durability
(Type 5 test)
Yes | Yes | Yes | Yes |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(NG/ biomethane only)
Yes (B5/B7 only) | Yes | — | —
Low temperature emissions
(Type 6 test)
Yes | — | — | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(both fuels)
| — | — | — | —
In-service conformity | Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes (B5/B7 only) | Yes | — | —
On-board diagnostics | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | — | —
CO2 emissions, fuel consumption, electric energy consumption and electric range | Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes (B5/B7 only) | Yes | Yes | Yes
Smoke opacity | — | — | — | — | — | — | — | — | — | Yes (B5/B7 only) | Yes | — | —
Engine power | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes
the following text is added after Figure I.2.4:
The dates of application of the reference fuels E10 and B7 for all new vehicles have been set out to minimise the test burden. If, however, technical evidence for vehicles certified with E5 or B5 reference fuels showing significantly higher emissions when tested with E10 or B7 is established, the Commission should make a proposal advancing these introduction dates.’;
Appendix 3 is amended as follows:
in points 3.2.1.8 and 3.2.1.10, footnote (a) is replaced by the following:
‘(a) Determined in accordance with the requirements of Annex XX to this Regulation.’;
point 3.3.1.1 is replaced by the following:
‘3.3.1.1.
Maximum hourly output: … kW
(manufacturer’s declared value)
3.3.1.1.1.
Maximum net power (a) … kW
(manufacturer’s declared value)
3.3.1.1.2.
Maximum 30 minutes power (a) … kW
(manufacturer’s declared value)’;
point 3.5.3. is replaced by the following:
the following points 3.5.3.1. and 3.5.3.2. are inserted:
‘3.5.3.1.
Electric energy consumption for pure electric vehicles … Wh/km
3.5.3.2.
Electric energy consumption for externally chargeable hybrid electric vehicles
3.5.3.2.1.
Electric energy consumption (Condition A, combined) … Wh/km
3.5.3.2.2.
Electric energy consumption (Condition B, combined) … Wh/km
3.5.3.2.3.
Electric energy consumption (weighted combined) … Wh/km’;
points 3.5.4. to 3.5.4.3. are deleted;
in Appendix 4, the ‘Addendum to EC type-approval certificate No …’ is amended as follows:
the following point 1.11.3 is inserted:
‘1.11.3
Maximum net torque: … Nm, at … min–1’;
point 4. is replaced by the following:
Maximum engine net power of internal combustion engine, net power and maximum 30 minutes power of electric drive train
4.1.1.
Engine speed (rpm) …
4.1.2.
Measured fuel flow (g/h) …
4.1.3.
Measured torque (Nm) …
4.1.4.
Measured power (kW) …
4.1.5.
Barometric pressure (kPa) …
4.1.6.
Water vapour pressure (kPa) …
4.1.7.
Intake air temperature (K) …
4.1.8.
Power correction factor when applied …
4.1.9.
Corrected power (kW) …
4.1.10.
Auxiliary power (kW) …
4.1.11.
Net power (kW) …
4.1.12.
Net torque (Nm) …
4.1.13.
Corrected specific fuel consumption (g/kWh) …
4.2.1.
Declared figures
4.2.2.
Maximum net power: … kW, at … min–1
4.2.3.
Maximum net torque: … Nm, at … min–1
4.2.4.
Maximum net torque at zero speed: .… Nm
4.2.5.
Maximum 30 minutes power: … kW
4.2.6.
Essential characteristics of the electric drive train
4.2.7.
Test DC voltage: … V
4.2.8.
Working principle: …
4.2.9.
Cooling system:
4.2.10.
Motor: liquid/air [Delete where not applicable.’]
4.2.11.
Variator: liquid/air [Delete where not applicable.]
the following point 5. is added:
in Appendix 6, Table 1 is replaced by the following table:
‘Euro 5a’ emissions standardexcludes revised measurement procedure for particulate matter, particle number standard and flex fuel vehicle low temperature emission testing with biofuel;
‘Euro 5b’ emissions standardFull Euro 5 emission requirements including revised measurement procedure for particulate matter, particle number standard for CI vehicles and flex fuel vehicle low temperature emission testing with biofuel;
‘Euro 6a’ emissions standardexcludes revised measurement procedure for particulate matter, particle number standard and flex fuel vehicle low temperature emission testing with biofuel;
‘Euro 6b’ emissions standardEuro 6 emission requirements including revised measurement procedure for particulate matter, particle number standards (preliminary values for PI vehicles) and flex fuel vehicle low temperature emission testing with biofuel;
‘Euro 6c’ emissions standardFull Euro 6 emission requirements, i.e. Euro 6b emission standard and final particle number standards for PI vehicles and use of E10 and B7 reference fuel (where applicable);
‘Euro 5’ OBD standardBase Euro 5 OBD requirements excluding in use performance ratio (IUPR), NOx monitoring for petrol vehicles and tightened PM threshold limits for diesel;
‘Euro 5+’ OBD standardincludes relaxed in use performance ratio (IUPR), NOx monitoring for petrol vehicles and tightened PM threshold limits for diesel;
‘Euro 6-’ OBD standardrelaxed OBD threshold limits;
‘Euro 6- plus IUPR’ OBD standardincludes relaxed OBD threshold limits and relaxed in use performance ratio (IUPR);
‘Euro 6-1’ OBD standardFull Euro 6 OBD requirements but with preliminary OBD threshold limits as defined in point 2.3.4 of Annex XI and partially relaxed IUPR;
‘Euro 6-2’ OBD standardFull Euro 6 OBD requirements but with final OBD threshold limits as defined in point 2.3.3 of Annex XI.’
Character | Emissions standard | OBD standard | Vehicle category and class | Engine | Implementation date: new types | Implementation date: new vehicles | Last date of registration
A | Euro 5a | Euro 5 | M, N1 class I | PI, CI | 1.9.2009 | 1.1.2011 | 31.12.2012
B | Euro 5a | Euro 5 | M1 to fulfil specific social needs (excluding M1G) | CI | 1.9.2009 | 1.1.2012 | 31.12.2012
C | Euro 5a | Euro 5 | M1G to fulfil specific social needs | CI | 1.9.2009 | 1.1.2012 | 31.8.2012
D | Euro 5a | Euro 5 | N1 class II | PI, CI | 1.9.2010 | 1.1.2012 | 31.12.2012
E | Euro 5a | Euro 5 | N1 class III, N2 | PI, CI | 1.9.2010 | 1.1.2012 | 31.12.2012
F | Euro 5b | Euro 5 | M, N1 class I | PI, CI | 1.9.2011 | 1.1.2013 | 31.12.2013
G | Euro 5b | Euro 5 | M1 to fulfil specific social needs (excluding M1G) | CI | 1.9.2011 | 1.1.2013 | 31.12.2013
H | Euro 5b | Euro 5 | N1 class II | PI, CI | 1.9.2011 | 1.1.2013 | 31.12.2013
I | Euro 5b | Euro 5 | N1 class III, N2 | PI, CI | 1.9.2011 | 1.1.2013 | 31.12.2013
J | Euro 5b | Euro 5+ | M, N1 class I | PI, CI | 1.9.2011 | 1.1.2014 | 31.8.2015
K | Euro 5b | Euro 5+ | M1 to fulfil specific social needs (excluding M1G) | CI | 1.9.2011 | 1.1.2014 | 31.8.2015
L | Euro 5b | Euro 5+ | N1 class II | PI, CI | 1.9.2011 | 1.1.2014 | 31.8.2016
M | Euro 5b | Euro 5+ | N1 class III, N2 | PI, CI | 1.9.2011 | 1.1.2014 | 31.8.2016
N | Euro 6a | Euro 6- | M, N1 class I | CI | | | 31.12.2012
O | Euro 6a | Euro 6- | N1 class II | CI | | | 31.12.2012
P | Euro 6a | Euro 6- | N1 class III, N2 | CI | | | 31.12.2012
Q | Euro 6b | Euro 6- | M, N1 class I | CI | | | 31.12.2013
R | Euro 6b | Euro 6- | N1 class II | CI | | | 31.12.2013
S | Euro 6b | Euro 6- | N1 class III, N2 | CI | | | 31.12.2013
T | Euro 6b | Euro 6- plus IUPR | M, N1 class I | CI | | | 31.8.2015
U | Euro 6b | Euro 6- plus IUPR | N1 class II | CI | | | 31.8.2016
V | Euro 6b | Euro 6- plus IUPR | N1 class III, N2 | CI | | | 31.8.2016
W | Euro 6b | Euro 6-1 | M, N1 class I | PI, CI | 1.9.2014 | 1.9.2015 | 31.8.2018
X | Euro 6b | Euro 6-1 | N1 class II | PI, CI | 1.9.2015 | 1.9.2016 | 31.8.2019
Y | Euro 6b | Euro 6-1 | N1 class III, N2 | PI, CI | 1.9.2015 | 1.9.2016 | 31.8.2019
ZA | Euro 6c | Euro 6-1 | M, N1 class I | PI, CI | | | 31.8.2018
ZB | Euro 6c | Euro 6-1 | N1 class II | PI, CI | | | 31.8.2019
ZC | Euro 6c | Euro 6-1 | N1 class III, N2 | PI, CI | | | 31.8.2019
ZD | Euro 6c | Euro 6-2 | M, N1 class I | PI, CI | 1.9.2017 | 1.9.2018 |
ZE | Euro 6c | Euro 6-2 | N1 class II | PI, CI | 1.9.2018 | 1.9.2019 |
ZF | Euro 6c | Euro 6-2 | N1 class III, N2 | PI, CI | 1.9.2018 | 1.9.2019 |
ZX | n.a. | n.a. | All vehicles | Battery full electric | 1.9.2009 | 1.1.2011 |
ZY | n.a. | n.a. | All vehicles | Fuel cell full electric | 1.9.2009 | 1.1.2011 |
ZZ | n.a | n.a. | All vehicles using certificates according to point 2.1.1 of Annex I | PI, CI | 1.9.2009 | 1.1.2011 |
Annex III is amended as follows:
point 3.4 is replaced by the following:
‘3.4.
The hydrocarbons ratios in paragraph 8.2 shall be understood as follows:
For petrol (E5) (C1H1,89O0,016) | d = 0,631 g/l
For petrol (E10) (C1H1,93O0,033) | d = 0,645 g/l
For diesel (B5) (C1H1,86O0,005) | d = 0,622 g/l
For diesel (B7) (C1H1,86O0,007) | d = 0,623 g/l
For LPG (C1H2,525) | d = 0,649 g/l
For NG/biomethane (CH4) | d = 0,714 g/l
For ethanol (E85) (C1H2,74O0,385) | d = 0,932 g/l
For ethanol (E75) (C1H2,61O0,329) | d = 0,886 g/l
For H2NG | d9,104 A 1361524,152 0,583A g/l
A being the quantity of NG/biomethane within the H2NG mixture, expressed in per cent volume.’
in point 3.8, the table is replaced by the following:
‘Fuel | X
Petrol (E5) | 13,4
Petrol (E10) | 13,4
Diesel (B5) | 13,5
Diesel (B7) | 13,5
LPG | 11,9
NG/biomethane | 9,5
Ethanol (E85) | 12,5
Ethanol (E75) | 12,7’
in Appendix 1 of Annex IV, point 2.2 is replaced by the following:
‘2.2.
The atomic ratios specified in point 5.3.7.3 shall be understood as follows:
Hcv
Atomic ratio of hydrogen to carbon
for petrol (E5) 1,89
for petrol (E10) 1,93
for LPG 2,53
for NG/biomethane 4,0
for ethanol (E85) 2,74
for ethanol (E75) 2,61
Ocv
Atomic ratio of oxygen to carbon
for petrol (E5) 0,016
for petrol (E10) 0,033
for LPG 0,0
for NG/biomethane 0,0
for ethanol (E85) 0,39
for ethanol (E75) 0,329’;
Annex IX is amended as follows:
Part A is amended as follows:
in point 1, the following table is inserted between the table ‘Type: Petrol (E5)’ and the table ‘Type: Ethanol (E85)’:
[The values quoted in the specifications are “true values”. In establishment of their limit values the terms of ISO 4259 Petroleum products - Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.]
Equivalent EN/ISO methods will be adopted when issued for properties listed above.
[A correction factor of 0,2 for MON and RON shall be subtracted for the calculation of the final result in accordance with EN 228:2008.] [The fuel may contain oxidation inhibitors and metal deactivators normally used to stabilise refinery gasoline streams, but detergent/dispersive additives and solvent oils shall not be added.] [Ethanol is the only oxygenate that shall be intentionally added to the reference fuel. The Ethanol used shall conform to EN 15376.] [The actual sulphur content of the fuel used for the Type 1 test shall be reported.] [There shall be no intentional addition of compounds containing phosphorus, iron, manganese, or lead to this reference fuel.’]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Research octane number, RON | | 95,0 | 98,0 | EN ISO 5164
Motor octane number, MON | | 85,0 | 89,0 | EN ISO 5163
Density at 1 5 °C | kg/m3 | 743,0 | 756,0 | EN ISO 12185
Vapour pressure (DVPE) | kPa | 56,0 | 60,0 | EN 13016-1
Water content | |
max 0,05 % v/v
Appearance at – 7 °C: clear and bright
EN 12937
Distillation: | | | |
evaporated at 70 °C
% v/v | 34,0 | 46,0 | EN ISO 3405
evaporated at 100 °C
% v/v | 54,0 | 62,0 | EN ISO 3405
evaporated at 150 °C
% v/v | 86,0 | 94,0 | EN ISO 3405
final boiling point
°C | 170 | 195 | EN ISO 3405
Residue | % v/v | — | 2,0 | EN ISO 3405
Hydrocarbon analysis: | | | |
olefins
% v/v | 6,0 | 13,0 | EN 22854
aromatics
% v/v | 25,0 | 32,0 | EN 22854
benzene
% v/v | — | 1,00 |
EN 22854
EN 238
saturates
% v/v | report | EN 22854
Carbon/hydrogen ratio | | report |
Carbon/oxygen ratio | | report |
Induction Period | minutes | 480 | — | EN ISO 7536
Oxygen content | % m/m | 3,3 | 3,7 | EN 22854
Solvent washed gum
(Existent gum content)
mg/100 ml | — | 4 | EN ISO 6246
Sulphur content | mg/kg | — | 10 |
EN ISO 20846
EN ISO 20884
Copper corrosion 3 hrs, 50 °C | | — | class 1 | EN ISO 2160
Lead content | mg/l | — | 5 | EN 237
Phosphorus content | mg/l | — | 1,3 | ASTM D 3231
Ethanol | % v/v | 9,0 | 10,0 | EN 22854
in point 2, the following table is added:
[The values quoted in the specifications are “true values”. In establishment of their limit values the terms of ISO 4259 Petroleum products – Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [The range for cetane number is not in accordance with the requirements of a minimum range of 4R. However, in the case of a dispute between fuel supplier and fuel user, the terms of ISO 4259 may be used to resolve such disputes provided replicate measurements, of sufficient number to archive the necessary precision, are made in preference to single determinations.] [Even though oxidation stability is controlled, it is likely that shelf life will be limited. Advice shall be sought from the supplier as to storage conditions and life.] [FAME content to meet the specification of EN 14214.’]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Cetane Index | | 46,0 | | EN ISO 4264
Cetane number | | 52,0 | 56,0 | EN ISO 5165
Density at 15 °C | kg/m3 | 833,0 | 837,0 | EN ISO 12185
Distillation: | | | |
50 % point
°C | 245,0 | — | EN ISO 3405
95 % point
°C | 345,0 | 360,0 | EN ISO 3405
final boiling point
°C | — | 370,0 | EN ISO 3405
Flash point | °C | 55 | — | EN ISO 2719
Cloud point | °C | — | –10 | EN 23015
Viscosity at 40 °C | mm2/s | 2,30 | 3,30 | EN ISO 3104
Polycyclic aromatic hydrocarbons | % m/m | 2,0 | 4,0 | EN 12916
Sulphur content | mg/kg | — | 10,0 |
EN ISO 20846
EN ISO 20884
Copper corrosion 3 hrs, 50 °C | | — | Class 1 | EN ISO 2160
Conradson carbon residue (10 % DR) | % m/m | — | 0,20 | EN ISO 10370
Ash content | % m/m | — | 0,010 | EN ISO 6245
Total contamination | mg/kg | — | 24 | EN 12662
Water content | mg/kg | — | 200 | EN ISO 12937
Acid number | mg KOH/g | — | 0,10 | EN ISO 6618
Lubricity (HFRR wear scan diameter at 60 °C) | μm | — | 400 | EN ISO 12156
Oxidation stability at 110 °C | h | 20,0 | | EN 15751
FAME | % v/v | 6,0 | 7,0 | EN 14078
in Part B, the following table is inserted between the table ‘Type: Petrol (E5)’ and the table ‘Type: Ethanol (E75)’:
[The values quoted in the specifications are “true values”. In establishment of their limit values the terms of ISO 4259 Petroleum products - Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.]
Equivalent EN/ISO methods will be adopted when issued for properties listed above.
[A correction factor of 0,2 for MON and RON shall be subtracted for the calculation of the final result in accordance with EN 228:2008.] [The fuel may contain oxidation inhibitors and metal deactivators normally used to stabilise refinery gasoline streams, but detergent/dispersive additives and solvent oils shall not be added.] [Ethanol is the only oxygenate that shall be intentionally added to the reference fuel. The ethanol used shall conform to EN 15376.] [The actual sulphur content of the fuel used for the Type 6 test shall be reported.] [There shall be no intentional addition of compounds containing phosphorus, iron, manganese, or lead to this reference fuel.’]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Research octane number, RON | | 95,0 | 98,0 | EN ISO 5164
Motor octane number, MON | | 85,0 | 89,0 | EN ISO 5163
Density at 15 °C | kg/m3 | 743,0 | 756,0 | EN ISO 12185
Vapour pressure (DVPE) | kPa | 56,0 | 95,0 | EN 13016-1
Water content | |
max 0,05 % v/v
Appearance at – 7 °C: clear and bright
EN 12937
Distillation: | | | |
evaporated at 70 °C
% v/v | 34,0 | 46,0 | EN ISO 3405
evaporated at 100 °C
% v/v | 54,0 | 62,0 | EN ISO 3405
evaporated at 150 °C
% v/v | 86,0 | 94,0 | EN ISO 3405
final boiling point
°C | 170 | 195 | EN ISO 3405
Residue | % v/v | — | 2,0 | EN ISO 3405
Hydrocarbon analysis: | | | |
olefins
% v/v | 6,0 | 13,0 | EN 22854
aromatics
% v/v | 25,0 | 32,0 | EN 22854
benzene
% v/v | — | 1,00 |
EN 22854
EN 238
saturates
% v/v | report | EN 22854
Carbon/hydrogen ratio | | report |
Carbon/oxygen ratio | | report |
Induction Period | minutes | 480 | — | EN ISO 7536
Oxygen content | % m/m | 3,3 | 3,7 | EN 22854
Solvent washed gum
(Existent gum content)
mg/100 ml | — | 4 | EN ISO 6246
Sulphur content | mg/kg | — | 10 |
EN ISO 20846
EN ISO 20884
Copper corrosion 3 hrs, 50 °C | | — | class 1 | EN ISO 2160
Lead content | mg/l | — | 5 | EN 237
Phosphorus content | mg/l | — | 1,3 | ASTM D 3231
Ethanol | % v/v | 9,0 | 10,0 | EN 22854
Annex XI is amended as follows:
in point 2.3.3., the table ‘Final Euro 6 OBD threshold limits’ is replaced by the following table:
Key: PI = Positive Ignition, CI = Compression Ignition.
[Positive ignition particulate mass and number limits apply only to vehicles with direct injection engines.’]
Reference mass
(RM) (kg)
Mass of carbon monoxide | Mass of non‐methane hydrocarbons | Mass of oxides of nitrogen | Mass of particulate matter | Number of particles
(CO)
(mg/km)
(NMHC)
(mg/km)
(NOx)
(mg/km)
(PM)
(mg/km)
(PN)
(#/km)
Category | Class | | PI | CI | PI | CI | PI | CI | CI | PI | CI | PI
M | — | All | 1900 | 1750 | 170 | 290 | 90 | 140 | 12 | 12 | |
N1 | I | RM ≤ 1305 | 1900 | 1750 | 170 | 290 | 90 | 140 | 12 | 12 | |
II | 1305 < RM ≤ 1760 | 3400 | 2200 | 225 | 320 | 110 | 180 | 12 | 12 | |
III | 1760 < RM | 4300 | 2500 | 270 | 350 | 120 | 220 | 12 | 12 | |
N2 | — | All | 4300 | 2500 | 270 | 350 | 120 | 220 | 12 | 12 | |
in point 2.3.4., the table ‘Preliminary Euro 6 OBD threshold limits’ is replaced by the following table: