For the purpose of this Annex, the ‘competent authority’ shall be:
for Section A, Subpart A,
for design organisations, the Agency;
for production organisations that have their principal place of business in a territory for which a Member State is responsible under the Convention on International Civil Aviation, signed in Chicago on 7 December 1944 (‘the Chicago Convention’), the authority designated by that Member State or by another Member State in accordance with Article 64 of Regulation (EU) 2018/1139, or the Agency if the responsibility has been reallocated to the Agency in accordance with Article 64 or 65 of Regulation (EU) 2018/1139;
for production organisations that have their principal place of business outside a territory for which a Member State is responsible under the Chicago Convention, the Agency;
for Section A, Subparts B, D, E, J, K, M, O and Q, the Agency;
for Section A, Subparts F and G:
for natural or legal persons that have their principal place of business in a territory for which a Member State is responsible under the Chicago Convention, the authority designated by that Member State or by another Member State in accordance with Article 64 of Regulation (EU) 2018/1139, or the Agency if the responsibility has been reallocated to the Agency in accordance with Article 64 or, as regards Subpart G, Article 65 of Regulation (EU) 2018/1139;
for natural or legal persons that have their principal place of business outside a territory for which a Member State is responsible under the Chicago Convention, the Agency;
for Section A, Subpart H and I, the authority designated by the Member State where the aircraft is registered or will be registered:
for Section A, Subpart P:
for aircraft registered in a Member State, the authority designated by the Member State of registry;
for unregistered aircraft, the authority designated by the Member State which prescribed the identification marks;
for the approval of the flight conditions related to the safety of the design, the Agency.
Section A of this Annex establishes the provisions that lay down the rights and obligations of the applicant for, and holder of, any certificate issued or to be issued in accordance with this Annex.
Section B of this Annex establishes the conditions for conducting the certification oversight and enforcement tasks as well as the administrative and management system requirements to be complied with by the competent authority that is responsible for the implementation of Section A of this Annex.
This Subpart establishes the general rights and obligations of the applicant for, and holder of, any certificate that has been issued or is to be issued in accordance with this Annex.
The actions and obligations required to be undertaken by the applicant for, or holder of, a certificate for a product, part, appliance, control and monitoring unit (CMU) or CMU component under this Section may be undertaken on their behalf by any other natural or legal person, provided the applicant for, or holder of, that certificate can show that they have made an agreement with the other person to ensure that the certificate holder’s obligations are and will be properly discharged.
Without prejudice to Regulation (EU) No 376/2014 of the European Parliament and of the Council [Regulation (EU) No 376/2014 of the European Parliament and of the Council of 3 April 2014 on the reporting, analysis and follow-up of occurrences in civil aviation, amending Regulation (EU) No 996/2010 of the European Parliament and of the Council and repealing Directive 2003/42/EC of the European Parliament and of the Council and Commission Regulations (EC) No 1321/2007 and (EC) No 1330/2007 (OJ L 122, 24.4.2014, p. 18).] and its delegated and implementing acts, all natural or legal persons that have applied for or hold a type-certificate, restricted type-certificate, supplemental type-certificate, European Technical Standard Order (ETSO) authorisation, major repair design approval or any other relevant approval deemed to have been issued under this Regulation shall:
establish and maintain a system for collecting, investigating and analysing occurrence reports in order to identify adverse trends or to address deficiencies and to extract occurrences whose reporting is mandatory in accordance with point 3 and those which are reported voluntarily. When the principal place of business is located in a Member State, a single system may be established to meet the requirements of Regulation (EU) No 376/2014 of the European Parliament and of the Council and its implementing acts and of Regulation (EU) 2018/1139 and its delegated and implementing acts. The reporting system shall include:
reports of and information related to failures, malfunctions, defects or other occurrences which cause or might cause adverse effects on the continuing airworthiness of the product, part, appliance, UAS, CMU or CMU component covered by the type-certificate, restricted type-certificate, supplemental type-certificate, ETSO authorisation, major repair design approval or by any other relevant approval deemed to have been issued under this Regulation;
errors, near misses and hazards that do not fall under point (i);
make available to known operators of the product, part, appliance, UAS, CMU or CMU component and, on request, to any person authorised under other implementing or delegated acts the information about the system established in accordance with point 1, and on how to provide reports of and information related to failures, malfunctions, defects or other occurrences referred to in point l(i);
report to the Agency any failure, malfunction, defect or other occurrence of which it is aware and is related to a product, part, appliance, UAS, CMU or CMU component covered by the type-certificate, restricted type-certificate, supplemental type-certificate, ETSO authorisation, major repair design approval or by any other relevant approval deemed to have been issued under this Regulation, and which has resulted or may result in an unsafe condition.
Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, any natural or legal person that holds or has applied for a production organisation approval certificate under Subpart G of this Section, or that produces a product, part, appliance, UAS, CMU or CMU component under Subpart F of this Section, shall:
establish and maintain a system for collecting and assessing occurrence reports, including reports on errors, near misses and hazards, in order to identify adverse trends or to address deficiencies and extract occurrences whose reporting is mandatory in accordance with points 2 and 3 of this point and those which are reported voluntarily. For organisations that have their principal place of business in a Member State, a single system may be established to meet the requirements of Regulation (EU) No 376/2014 and its implementing acts and of Regulation (EU) 2018/1139 and its delegated and implementing acts;
report to the responsible design approval holder all the cases where products, parts, appliances, UAS, CMUs or CMU components have been released by the production organisation and possible deviations from the applicable design data have been subsequently identified, and investigate with the design approval holder to identify those deviations which could lead to an unsafe condition;
report to the competent authority of the Member State responsible in accordance with point 21.1 and the Agency the deviations that have been identified in accordance with point 21.A.3A(b)2 and which could lead to an unsafe condition;
if the production organisation acts as a supplier to another production organisation, also report to that other organisation all the cases where it has released products, parts, appliances, UAS, CMUs or CMU components to that organisation and the possible deviations from the applicable design data that have been subsequently identified.
Without prejudice to Regulation (EU) No 376/2014 of the European Parliament and of the Council and its delegated and implementing acts, any natural or legal person, when reporting in accordance with points (a)(3), (b)(2), (b)(3) and (b)(4), shall appropriately protect the confidentiality of the person who reports and of the person(s) mentioned in the report.
Without prejudice to Regulation (EU) No 376/2014 of the European Parliament and of the Council and its delegated and implementing acts, any natural or legal person shall make the reports referred to in points (a)(3) and (b)(3) in a form and manner established by the Agency or the competent authority, respectively, and dispatch them as soon as practicable and in any case not later than 72 hours after the natural or legal person has identified that the occurrence may lead to a possible unsafe condition, unless exceptional circumstances prevent this.
Without prejudice to Regulation (EU) No 376/2014 of the European Parliament and of the Council and its delegated and implementing acts, if an occurrence reported under point (a)(3) or under point (b)(3) results from a deficiency in the design or a production deficiency, the holder of the type-certificate, restricted type-certificate, supplemental type-certificate, major repair design approval, ETSO authorisation or any other relevant approval deemed to have been issued under this Regulation, or the production organisation as appropriate, shall investigate the reason for the deficiency and report to the competent authority of the Member State responsible in accordance with point 21.1 and to the Agency the results of its investigation and any action it intends to take or proposes to be taken to correct that deficiency.
If the competent authority finds that action is required to correct the deficiency, the holder of the type-certificate, restricted type-certificate, supplemental type-certificate, major repair design approval, ETSO authorisation or any other relevant approval deemed to have been issued under this Regulation, or the production organisation as appropriate, shall submit the relevant data to the competent authority upon its request.
An airworthiness directive means a document issued or adopted by the Agency which mandates actions to be performed on an aircraft or on a CMU to restore an acceptable level of safety, when evidence shows that the safety level of the aircraft, UAS or CMU may otherwise be compromised.
The Agency shall issue an airworthiness directive when:
an unsafe condition has been determined by the Agency to exist in an aircraft, a UAS or a CMU, as a result of a deficiency in the aircraft, or an engine, propeller, part or appliance installed on this aircraft, or as a result of a deficiency in the CMU or the CMU component; and
that condition is likely to exist or develop in other aircraft, UAS or CMUs.
When an airworthiness directive has to be issued by the Agency to correct the unsafe condition referred to in point (b), or to require the performance of an inspection, the holder of the type-certificate, restricted type-certificate, supplemental type-certificate, major repair design approval, ETSO authorisation or any other relevant approval deemed to have been issued under this Regulation, shall:
propose the appropriate corrective action or required inspections, or both, and submit details of these proposals to the Agency for approval; and
following the approval by the Agency of the proposals referred to in point 1, make available to all known operators or owners of the product, part, appliance, UAS, CMU or CMU component and, on request, to any person required to comply with the airworthiness directive, appropriate descriptive data and accomplishment instructions.
An airworthiness directive shall contain at least the following information:
an identification of the unsafe condition;
an identification of the affected aircraft or CMU;
the action(s) required;
the compliance time for the required action(s);
the date of entry into force of the airworthiness directive.
Each holder of a type-certificate, restricted type-certificate, supplemental type- certificate, ETSO authorisation, approval of a change to type-certificate or approval of a repair design, shall collaborate with the production organisation as necessary to ensure:
the satisfactory coordination of design and production required by 21A.122, 21A.130(b)(3) and (4), 21A.133 and 21A.165(c)(2) and (3) as appropriate, and
the proper support of the continued airworthiness of the product, part, appliance, UAS, CMU or CMU component.
All natural or legal persons that hold or have applied for a type-certificate, restricted type-certificate, supplemental type-certificate, ETSO authorisation, design or repair approval, permit to fly, production organisation approval certificate or letter of agreement under this Regulation shall:
when they design a product, part, appliance, UAS, CMU or CMU component, or changes or repairs thereto, establish a record-keeping system and maintain the relevant design information/data; that information/data shall be made available to the Agency in order to provide the information/data that is necessary to ensure the continued airworthiness of the product, part, appliance, UAS, CMU or CMU component, the continued validity of the operational suitability data, and compliance with the applicable environmental protection requirements;
when they produce a product, part, appliance, CMU or CMU component, record the details of the production process relevant to the conformity of the product, part, appliance, CMU or CMU component with the applicable design data, and the requirements imposed on their partners and suppliers, and make that data available to their competent authority in order to provide the information that is necessary to ensure the continuing airworthiness of the product, part, appliance, UAS, CMU or CMU component;
with regard to permits to fly:
maintain the documents that are produced to establish and justify the flight conditions, and make them available to the Agency and to their competent authority of the Member State in order to provide the information that is necessary to ensure the continued airworthiness of the aircraft, the UAS and the CMU;
when they issue a permit to fly under the privilege of approved organisations, maintain the documents associated with it, including inspection records and documents that support the approval of the flight conditions and the issuance of the permit to fly itself, and make them available to the Agency and to their competent authority of the Member State responsible for the oversight of the organisation in order to provide the information that is necessary to ensure the continued airworthiness of the aircraft, the UAS and the CMU;
retain records of the competence and qualifications, referred to in points 21.A.139(c), 21.A.145(b), 21.A.145(c), 21.A.239(c), 21.A.245(a) or 21.A.245(e)(1), of the personnel that are involved in the following functions:
design or production;
independent monitoring of the compliance of the organisation with the relevant requirements;
safety management;
retain records of the authorisation of personnel, when they employ personnel that:
exercise the privileges of the approved organisation pursuant to points 21.A.163 and/or 21.A.263, as appropriate;
carry out the independent function to monitor the compliance of the organisation with the relevant requirements pursuant to points 21.A.139(e) and/or 21.A.239(e), as appropriate;
carry out the independent verification function of the demonstration of compliance pursuant to point 21.A.239(d)(2).
The holder of a type-certificate, restricted type-certificate, or supplemental type-certificate shall:
‘(a) produce, maintain and update master copies of all manuals or variations in the manuals required by the applicable type-certification basis, the applicable operational suitability data certification basis and the applicable environmental protection requirements for the product, UAS, CMU or article, and provide copies, on request, to the Agency;
for unmanned aircraft, determine whether the installation of a CMU in a physical environment is necessary, and provide the operator with all the necessary instructions for the installation of the CMU and for its installation to be released in accordance with Annex I (Part-ML.UAS) to Commission Delegated Regulation (EU) 2024/1107.
‘(a) The holder of a type-certificate, restricted type-certificate, supplemental type-certificate, design change or repair design approval shall develop or reference the instructions which are necessary for ensuring that the airworthiness standard related to the aircraft, the UAS and the CMU type and any associated part or CMU component is maintained throughout the operational life of the aircraft or the UAS, when demonstrating compliance with the applicable type-certification basis established and notified by the Agency in accordance with point 21.B.80.
At least one set of complete instructions for continued airworthiness shall be provided by the holder of:
a type-certificate or restricted type-certificate to each known owner of one or more products, UAS or CMUs upon their delivery or upon the issuance of the first certificate of airworthiness or restricted certificate of airworthiness for the affected aircraft, whichever occurs later;
a supplemental type-certificate or design change approval to all known operators of the product, the UAS or the CMU affected by the change upon the release to service of the modified product or modified CMU;
a repair design approval to all known operators of the product or the CMU affected by the repair upon the release to service of the product or the CMU in which the repair design is embodied; the repaired product, part, appliance, CMU or CMU component may be released into service before the related instructions for continued airworthiness have been completed, but this shall be for a limited service period, and in agreement with the Agency.
Thereafter, those design approval holders shall make those instructions available on request to any other person required to comply with those instructions.
By way of derogation from point (b), the type-certificate holder or restricted type-certificate holder may delay the availability of a part of the instructions for continued airworthiness, dealing with long lead accomplishment instructions of a scheduled nature, until after the product or the CMU, or modified product or modified CMU, has entered into service, but shall make those instructions available before the use of this data is required for the product or modified product.
The design approval holder that is required to provide instructions for continued airworthiness in accordance with point (b) shall also make available the changes to those instructions to all known operators of the product, the UAS or the CMU affected by the change and, on request, to any other person required to comply with those changes. That design approval holder shall demonstrate to the Agency, on request, the adequacy of the process of making changes to the instructions for continued airworthiness available in accordance with this point.
Any natural or legal person that holds or has applied for a type-certificate, restricted type-certificate, supplemental type-certificate, ETSO authorisation, design change or repair approval, certificate of airworthiness, noise certificate, permit to fly, design organisation approval, production organisation approval certificate or letter of agreement under this Regulation, shall:
grant the competent authority access to any facility, product, part, appliance, CMU, CMU component, document, record, data, process, procedure or to any other material in order to review any report, make any inspection, or perform or witness any flight and ground test, as necessary, in order to verify the initial and continued compliance of the organisation with the applicable requirements of Regulation (EU) 2018/1139 and its delegated and implementing acts;
make arrangements to ensure the competent authority has access, as provided for in point (a), also in respect of the natural or legal person’s partners, suppliers and subcontractors.
This Subpart establishes the procedure for issuing type-certificates for products and CMUs and restricted type-certificates for aircraft, and establishes the rights and obligations of the applicants for, and holders of, those certificates.
Any natural or legal person that has demonstrated, or is in the process of demonstrating, its capability in accordance with point 21.A.14 shall be eligible as an applicant for a type-certificate or a restricted type-certificate under the conditions laid down in this Subpart.
An applicant for a type-certificate or restricted type-certificate shall demonstrate its capability by holding a design organisation approval, issued by the Agency in accordance with Subpart J.
By way of derogation from point (a), as an alternative procedure to demonstrate its capability, an applicant may seek the agreement of the Agency for the use of procedures setting out the specific design practices, resources and sequence of activities necessary to comply with this Annex I (Part 21), when the product is one of the following:
an ELA2 aircraft;
an engine or propeller installed in ELA2 aircraft;
a piston engine;
a fixed or adjustable pitch propeller.
By way of derogation from point (a), an applicant may demonstrate its capability by obtaining the Agency's acceptance of its certification programme established in accordance with point 21.A.15(b), where the product to be certified is:
an ELA1 aircraft; or
an engine or propeller installed in ELA1 aircraft.
An application for a type-certificate or restricted type-certificate shall be made in a form and manner established by the Agency.
An application for a type-certificate or restricted type-certificate shall include, as a minimum, preliminary descriptive data of the product, the UAS or the CMU, and the kind of operations for which certification is requested. In addition, it shall include, or be supplemented after the initial application by, a certification programme for the demonstration of compliance in accordance with point 21.A.20, consisting of all of the following:
a detailed description of the type design, including all the configurations to be certified;
the proposed operating characteristics and limitations;
the intended use of the product, the UAS or the CMU, and the kind of operations for which certification is requested;