Section A of this Annex (Part 21 Light) establishes the provisions governing the rights and obligations of the following persons having their principal place of business located in a Member State:
the applicant for, and holder of, any certificate issued or to be issued in accordance with this Annex;
natural and legal persons declaring, in accordance with this Annex, design compliance, design capabilities or production capabilities, or intending to make such declarations;
the signatory of a statement of conformity for an aircraft, or an authorised release certificate (EASA Form 1) for an engine, propeller or part produced in accordance with this Annex.
Section B of this Annex establishes the provisions governing the certification, oversight and enforcement by the Agency and national competent authorities in accordance with this Annex and establishes requirements for their administration and management systems relating to the exercise of these tasks.
For the purpose of this Annex, ‘competent authority’ shall be:
for Section A, Subpart A,
for design organisations, the Agency;
for a production organisation, the authority designated by the Member State where the organisation has its principal place of business; or the Agency, if that responsibility has been reallocated to the Agency in accordance with Article 64 or 65 of Regulation (EU) 2018/1139;
for Section A, Subparts B, C, D, E, F, J, K, M, N, and Q, the Agency;
for Section A, Subparts G, H, I and R, the authority designated by the Member State where the organisation has its principal place of business; or the Agency, if that responsibility has been reallocated to the Agency in accordance with Article 64 or 65 of Regulation (EU) 2018/1139;
for Section A, Subpart P:
for aircraft registered in a Member State, the authority designated by the Member State of registry;
for unregistered aircraft, the authority designated by the Member State which prescribed the identification marks;
for the approval of flight conditions related to the safety of the design, the Agency.
This Section establishes general rights and obligations that are applicable to:
the applicant for, and holder of, any certificate issued or to be issued in accordance with this Annex;
any declarant of design or production capability or of design compliance; and
any natural or legal person issuing a statement of conformity for an aircraft, or an authorised release certificate (EASA Form 1) for an engine, propeller or part produced.
The actions and obligations required to be undertaken by the applicant for, or holder of, a certificate for a product or part or by the declarant of a declaration of design compliance under this Section may be undertaken on its behalf by any other natural or legal person, provided that the applicant’s, holder’s or declarant’s obligations are and will be properly discharged.
Without prejudice to Regulation (EU) No 376/2014 of the European Parliament and of the Council [Regulation (EU) No 376/2014 of the European Parliament and of the Council of 3 April 2014 on the reporting, analysis and follow-up of occurrences in civil aviation, amending Regulation (EU) No 996/2010 of the European Parliament and of the Council and repealing Directive 2003/42/EC of the European Parliament and of the Council and Commission Regulations (EC) No 1321/2007 and (EC) No 1330/2007 (OJ L 122, 24.4.2014, p. 18).] and its delegated and implementing acts, any natural or legal person who holds or has applied for a type certificate, supplemental type certificate, major repair design approval, or any other relevant certificate deemed to have been issued under this Annex, or who has declared the compliance of an aircraft design, or a design change or repair design to it under this Annex shall:
establish and maintain a system for collecting, investigating and analysing occurrence reports in order to identify adverse trends or to address deficiencies, and to extract occurrences, whose reporting is mandatory in accordance with point (3) and those which are reported voluntarily. The reporting system shall include:
reports of and information related to failures, malfunctions, defects or other events which cause or might cause adverse effects on the continuing airworthiness of the product or part covered by the type certificate, supplemental type certificate, major repair design approval, or any other relevant certificate deemed to have been issued under this Annex, or by the declaration of design compliance issued under this Annex;
reports of errors, near misses, and hazards that do not fall under point (i);
make available to known operators of the product or part, and, on request, to any person authorised under other associated implementing acts or delegated acts, the information about the system established in accordance with point (a)(1), and on how to provide such reports of and information related to failures, malfunctions, defects or other events referred to in point (a)(1)(i);
report to the Agency any failure, malfunction, defect or other event of which they are aware related to a product or part, covered by the type certificate, supplemental type certificate, major repair design approval, or any other relevant certificate deemed to have been issued under this Annex, or by a declaration of design compliance issued under this Annex, and which has resulted in or may result in an unsafe condition.
Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, any natural or legal person who has declared their production capability under Subpart G of this Annex, or who produces a product or part under Subpart R of this Annex, shall:
establish and maintain a system for collecting and assessing internal occurrence reports, including reports on internal errors, near misses, and hazards, in order to identify adverse trends or to address deficiencies, and extract occurrences, whose reporting is mandatory in accordance with points (2) and (3) and those which are reported voluntarily;
report, to the responsible design approval holder or declarant of a declaration of design compliance, all cases in which products or parts have been released by them and subsequently identified to have possible deviations from the applicable design data, and investigate with the design approval holder or the declarant of a declaration of design compliance, to identify those deviations which could lead to an unsafe condition;
report to the Agency and the competent authority of the Member State responsible in accordance with point 21L.2, if any, the deviations which could lead to an unsafe condition that were identified according to point (2) of point 21L.A.3(b);
if acting as a supplier to another production organisation, report to that other organisation all the cases in which it has released products or parts to that organisation and subsequently identified them to have possible deviations from the applicable design data.
The reporting obligations of point 21.A.3A(b) of Annex I of natural and legal persons who hold or have applied for a production organisation approval shall include occurrences related to products and parts produced in conformity with design data approved or declared in accordance with this Annex, and, where the design compliance was declared, reports shall be made to the declarant of design compliance.
Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, any natural or legal person referred to in points (a) and (b) when reporting in accordance with points (a)(3), (b)(2), (b)(3) and (b)(4), shall appropriately safeguard the confidentiality of the reporter and of the persons mentioned in the report.
Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, any natural or legal person referred to in points (a) and (b) shall make the reports defined in points (a)(3) and (b)(3) in a form and manner established by the competent authority as soon as practicable, and in any case, dispatch the reports not later than 72 hours after the natural or legal person referred to in points (a) and (b) has identified the possible unsafe condition, unless exceptional circumstances prevent this.
Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, if an occurrence reported under point (a)(3) or under point (b)(3) results from a deficiency in the design, or a production deficiency, the holder of the type certificate, supplemental type certificate, major repair design approval, or any other relevant certificate deemed to have been issued under this Annex, the declarant of a declaration of design compliance or the production organisation referred to in point (b) as appropriate, shall investigate the reason for the deficiency and report to the Agency and to the competent authority of the Member State responsible in accordance with point 21L.2, if any, the results of its investigation and any action it is taking or proposes to take to correct that deficiency.
If the competent authority finds that an action is required to correct the deficiency, the holder of the type certificate, supplemental type certificate, major repair design approval, or any other relevant certificate deemed to have been issued under this Annex, the declarant of a declaration of design compliance, or the production organisation referred to in point (b) as appropriate, shall submit the relevant data to the competent authority upon its request.
When an airworthiness directive has to be issued by the Agency in accordance with point 21L.B.23 to correct an unsafe condition, or to require the performance of an inspection, the holder of the type certificate, supplemental type certificate, major repair design approval, or any other relevant certificate deemed to have been issued under this Annex, as well as the declarant of a declaration of design compliance, as applicable, shall:
propose the appropriate corrective action or required inspections, or both, and submit details of these proposals to the Agency for approval;
following the approval by the Agency of the proposals referred to under point (a), make available to all known operators or owners of the product or part, and, on request, to any person required to comply with the airworthiness directive, appropriate descriptive data and accomplishment instructions.
The holder of a type certificate, supplemental type certificate, approval of a change to type certificate or approval of a repair design, the declarant of a declaration of design compliance, and the organisation or the natural or legal person producing products or parts of that specific design shall collaborate so as to ensure that the product or part are in conformity to that design and to ensure the continued airworthiness of the product or part.
The holder of a type certificate, supplemental type certificate, approval of a change to type certificate or approval of a repair design, or the declarant of a declaration of design compliance shall specify the marking for products or parts in accordance with Subpart Q of this Annex.
The organisation or the natural or legal person producing products or parts shall mark these products and parts in accordance with Subpart Q of this Annex.
All natural or legal persons who hold or who have applied for a type certificate, supplemental type certificate, repair design approval, or permit to fly, who have declared design compliance, who have issued a declaration of design or production capability, or who produce products or parts under this Regulation shall:
when designing a product or part or changes or repairs thereto, establish a record-keeping system that incorporates the requirements imposed on its partners and subcontractors and maintain the relevant design information/data and hold it at the disposal of the Agency in order to provide the information necessary to ensure their continued airworthiness and compliance with the applicable environmental protection requirements;
when producing a product or part, establish a record-keeping system and record the details of the work relevant to the conformity of the products or parts, and the requirements imposed on its partners and suppliers, and hold them at the disposal of the competent authority in order to provide the information necessary to ensure the continuing airworthiness of the product and part;
with regard to permits to fly, in addition to the record-keeping requirements established in point 21.A.5(c) of Annex I, record any documents produced to demonstrate compliance with the additional requirements established in point 21L.A.241(b), and hold them at the disposal of the Agency and the competent authority;
retain records of competence and the qualifications of personnel who are involved in design or production and in the independent function to monitor the compliance, if required by points 21L.A.125(c), 21L.A.175(b) or 21L.A.175(e).
The holder of a type certificate or supplemental type certificate or the declarant of a declaration of design compliance shall produce, maintain and update master copies of all the manuals or variations in the manuals required by the applicable type-certification basis, the applicable detailed technical specifications and the applicable environmental protection requirements for the product or part, and provide copies, on request, to the Agency.
The holder of a type certificate, supplemental type certificate, design change or repair design approval or the declarant of a declaration of design compliance shall establish the information which is necessary for ensuring that the airworthiness of the aircraft type and any associated part, conforming to that design, is maintained throughout the operational life.
The holder of a type certificate, supplemental type certificate, design change or repair design approval or the declarant of a declaration of design compliance shall provide the information established in (a) before that design is released to service.
The instructions for continued airworthiness shall be provided by:
the holder of a type certificate or by the declarant of a declaration of design compliance to each known owner of one or more products upon its delivery or upon the issuance of the first certificate of airworthiness or restricted certificate of airworthiness, as applicable, for the affected aircraft, whichever occurs later;
the holder of a type certificate, supplemental type certificate or minor change approval or by the declarant of a declaration of design compliance for a design change to all known operators of the product affected by the change upon the release to service of the modified product;
the holder of a repair design approval or by the declarant of a declaration of design compliance for a repair design to all known operators of the product affected by the repair upon the release to service of the product in which the repair design is embodied. The repaired product or part may be released into service before the related instructions for continued airworthiness have been completed, but this shall be for a limited service period, and in agreement with the Agency.
Thereafter, these certificate holders or declarants shall make this information available on request to any other person required to comply with those instructions for continued airworthiness.
By way of derogation from point (b), the type-certificate holder or declarant of a declaration of design compliance may delay the availability of a part of the instructions for continued airworthiness, dealing with long lead accomplishment instructions of a scheduled nature, until after the product or modified product has entered into service, but shall make those instructions available before the use of this data is required for the product or modified product.
The design approval holder or declarant of a declaration of design compliance who is required to provide instructions for continued airworthiness in accordance with point (b) shall also make available all the changes to those instructions to all the known operators of the product affected by the change, and, on request, to any other person required to comply with those changes.
All natural or legal persons who hold or who have applied for a type certificate, supplemental type certificate, major repair design approval, permit to fly, certificate of airworthiness, restricted certificate of airworthiness, noise certificate or restricted noise certificate, who have declared design compliance, who have declared their design or production capability or who produce aircraft, engines, propellers or parts under Subpart R of this Annex, shall:
grant the competent authority access to any facility, product, part, document, record, data, processes, procedures or any other material, and permit the review of any report and make any inspection and perform or witness any test that is necessary to verify the compliance and the continued compliance with the applicable requirements of this Section;
if the natural or legal person uses partners, suppliers or subcontractors, make arrangements with them to ensure that the competent authority has access and can investigate as described in point (a).
After the receipt of the notification of findings, the natural or legal person who holds or who has applied for a type certificate, supplemental type certificate, major repair design approval, permit to fly, certificate of airworthiness, restricted certificate of airworthiness, noise certificate or restricted noise certificate, who has declared design compliance, who has declared their design or production capability or who produces aircraft, engines, propellers or parts under Subpart R of this Annex, shall take the following steps within the time period determined by the competent authority in accordance with point (d) or (e) of point 21L.B.21:
identify the root cause(s) of, and contributing factor(s) to, the non-compliance;
define a corrective action plan and propose it to the competent authority;
demonstrate the implementation of the corrective action(s) to the satisfaction of the competent authority.
An observation notified by the competent authority in accordance with point (f) of point 21L.B.21 shall be given due consideration. The natural or legal person shall record the decision taken in respect of those observations.
A legal or natural person may use any alternative means of compliance to the acceptable means of compliance (AMC) to establish compliance with this Regulation.
If a natural or legal person wishes to use an alternative means of compliance, they shall, prior to using it, provide the competent authority with a full description. The description shall include any revisions to manuals or procedures that may be relevant, as well as an explanation indicating how compliance with this Regulation is achieved.
The natural or legal person may use those alternative means of compliance subject to prior approval from the competent authority.
This Subpart establishes the procedure for applying for type certificates, and establishes the rights and obligations of the applicants for, and holders of, those certificates for products, when the product is one of the following:
an aeroplane with a maximum take-off mass (MTOM) of 2000 kg or less with a seating configuration of maximum four persons;
a sailplane or powered sailplane with an MTOM of 2000 kg or less;
a balloon;
a hot air airship;
a passenger gas airship designed for not more than four persons;
a rotorcraft with an MTOM of 1200 kg or less with a seating configuration of maximum four persons;
a piston engine and fixed pitch propeller that are intended to be installed on an aircraft referred to in points (a) to (f). In such cases, the type certificate data sheet shall be appropriately annotated to only permit installation of the engine or propeller on such aircraft;
gyroplanes.
Any natural or legal person who has demonstrated, or is in the process of demonstrating, their design capability in accordance with point 21L.A.23, may apply for a type certificate under the conditions laid down in this Subpart.
An applicant for a type certificate shall demonstrate their design capability by:
holding a design organisation approval with terms of approval that cover the respective category of the product, issued by the Agency in accordance with Subpart J of Section A of Annex I (Part 21); or
declaring their design capability for the type of design work and the category of the product in accordance with Subpart J of this Annex.
An application for a type certificate shall be made in a form and manner established by the Agency.
An application for a type certificate shall include as a minimum:
a justification that the application is within the scope as established in point 21L.A.21;
preliminary descriptive data of the product, the intended use, and the kind of operation of the product for which certification is requested;
a proposal for the type-certification basis and the applicable environmental protection requirements, prepared in accordance with the requirements and options specified in points 21L.B.43 and 21L.B.45;
a compliance demonstration plan detailing the means and methods of compliance that shall be updated by the applicant when there are changes to the certification project that affect points (1) to (3) or any changes to the means and methods of compliance.
An application for a type certificate shall remain valid for 3 years. In case a type certificate has not been issued within this period, a new application shall be made in accordance with points (a) and (b).
The applicant for a type certificate shall, following the acceptance of the compliance demonstration plan by the Agency and in accordance with its contents, then:
demonstrate compliance with the applicable type-certification basis as established and notified to the applicant by the Agency in accordance with point 21L.B.43;
demonstrate compliance with the applicable environmental protection requirements as established and notified to the applicant by the Agency in accordance with point 21L.B.45; and
provide the Agency with the means by which such compliance has been demonstrated.
The applicant for a type certificate shall provide the Agency with a recorded justification of the means of compliance within compliance documents according to the compliance demonstration plan.