Unless otherwise stated, reference numbers used in the column entitled “Description” refer to the descriptions of dual-use items and technology set out in Annex I to Regulation (EU) 2021/821.
A reference number in the column entitled “Related item from Annex I to Regulation (EU) 2021/821” means that the characteristics of the item described in the column “Description” lie outside the parameters set out in the description of the dual-use entry referred to.
Definitions of terms between ‘single quotation marks’ are given in a technical note to the relevant item.
Definitions of terms between “double quotation marks” can be found in Annex I to Regulation (EU) 2021/821.
The object of the prohibitions contained in this Annex should not be defeated by the export of any non-prohibited goods (including plant) containing one or more prohibited components when the prohibited component or components are the principal element of the goods and can feasibly be removed or used for other purposes.
N.B.: In judging whether the prohibited component or components are to be considered the principal element, it is necessary to weigh the factors of quantity, value and technological know-how involved and other special circumstances which might establish the prohibited component or components as the principal element of the goods being procured.
The goods specified in this Annex include both new and used goods.
The sale, supply, transfer or export of “technology” which is “required” for the “development”, “production” or “use” of goods the sale, supply, transfer or export of which is prohibited in Part A (Goods) below, is prohibited in accordance with the provisions of Section II.B.
The sale, supply, transfer or export of “technology” which is “required” for the “development” or “production” of goods the sale, supply, transfer or export of which is controlled in Part A (Goods) of Annex IIa, is prohibited in accordance with the provisions of Section II.B.
The “technology” “required” for the “development”, “production” or “use” of prohibited goods remains under prohibition even when applicable to non-prohibited goods.
Prohibitions do not apply to that “technology” which is the minimum necessary for the installation, operation, maintenance (checking) and repair of those goods which are not prohibited or the export of which has been authorised in accordance with Regulation (EC) No 423/2007, Regulation (EU) No 961/2010 or this Regulation.
Prohibitions on “technology” transfer do not apply to information “in the public domain”, to “basic scientific research” or to the minimum necessary information for patent applications.
A0. Nuclear Materials, Facilities, and Equipment
No | Description | Related item from Annex I to Regulation (EU) 2021/821
A0.001 |
Hollow cathode lamps as follows:
Iodine hollow cathode lamps with windows in pure silicon or quartz; or
Uranium hollow cathode lamps.
—
A0.002 | Faraday isolators in the wavelength range 500 nm – 650 nm. | —
A0.003 | Optical gratings in the wavelength range 500 nm – 650 nm. | —
A0.004 | Optical fibres in the wavelength range 500 nm – 650 nm coated with anti-reflecting layers in the wavelength range 500 nm – 650 nm and having a core diameter greater than 0,4 mm but not exceeding 2 mm | —
A0.005 |
Nuclear reactor vessel components and testing equipment, other than those specified in 0A001, as follows:
Seals;
Internal components; or
Sealing, testing and measurement equipment.
0A001
A0.006 | Nuclear detection systems for detection, identification or quantification of radioactive materials and radiation of nuclear origin and specially designed components thereof other than those specified in 0A001.j. or 1A004.c. |
0A001.j
1A004.c
A0.007 |
Bellows-sealed valves made of aluminium alloy or stainless steel type 304, 304L or 316L.
Note: This item does not cover bellow valves defined in 0B001.c.6 and 2A226.
0B001.c.6
2A226
A0.008 |
Laser mirrors, other than those specified in 6A005.e, consisting of substrates having a thermal expansion coefficient of 10-6K-1 or less at 20 oC (e.g. fused silica or sapphire).
Note: This item does not cover optical systems specially designed for astronomical applications, except if the mirrors contain fused silica.
0B001.g.5,
6A005.e
A0.009 | Laser lenses, other than those specified in 6A005.e.2, consisting of substrates having a thermal expansion coefficient of 10-6K-1 or less at 20 oC (e.g. fused silica). |
0B001.g,
6A005.e.2
A0.010 | Pipes, piping, flanges, fittings made of, or lined with, nickel or nickel alloy containing more than 40 % nickel by weight, other than those specified in 2B350.h.1. | 2B350
A0.011 |
Vacuum pumps other than those specified in 0B002.f.2 or 2B231, as follows:
Turbomolecular pumps having a flowrate equal to or greater than 400 l/s;
Roots type vacuum roughing pumps having a volumetric aspiration flowrate greater than 200 m3/h; or
Bellows-sealed, scroll, dry compressor, and bellows-sealed, scroll, dry vacuum pumps.
0B002.f.2,
2B231
A0.012 | Shielded enclosures for the manipulation, storage and handling of radioactive substances (Hot cells). | 0B006
A0.013 | “Natural uranium” or “depleted uranium” or thorium in the form of metal, alloy, chemical compound or concentrate and any other material containing one or more of the foregoing, other than those specified in 0C001. | 0C001
A0.014 | Detonation chambers having a capacity of explosion absorption of more than 2,5 kg TNT equivalent. | —
A1. Materials, chemicals, ‘microorganisms’ and ‘toxins’
No | Description | Related item from Annex I to Regulation (EU) 2021/821
A1.001 | Bis (2-ethylhexyl) phosphoric acid (HDEHP or D2HPA) (CAS 298-07-7) solvent in any quantity, with a purity greater than 90 %. | —
A1.002 | Fluorine gas (CAS 7782-41-4), with a purity of at least 95 %. | —
A1.005 |
Electrolytic cells for fluorine production with an output capacity greater than 100 g of fluorine per hour.
Note: This item does not cover electrolytic cells defined in item 1B225.
1B225
A1.006 | Catalysts, other than those prohibited by 1A225, containing platinum, palladium or rhodium, usable for promoting the hydrogen isotope exchange reaction between hydrogen and water for the recovery of tritium from heavy water or for the production of heavy water. |
1B231,
1A225
A1.007 |
Aluminium and its alloys, other than those specified in 1C002.b.4 or 1C202.a, in crude or semi-fabricated form having either of the following characteristics:
Capable of an ultimate tensile strength of 460 MPa or more at 293 K (20 oC); or
Having a tensile strength of 415 MPa or more at 298 K (25 oC).
1C002.b.4,
1C202.a
A1.008 | Magnetic metals, of all types and of whatever form, having an initial relative permeability of 120000 or more and a thickness between 0,05 and 0,1 mm. | 1C003.a
A1.009 |
‘Fibrous or filamentary materials’ or prepregs, as follows:
N.B. see also II.A1.019.a.
Carbon or aramid ‘fibrous or filamentary materials’ having either of the following characteristics:
A ‘specific modulus’ exceeding 10 × 106 m; or
A ‘specific tensile strength’ exceeding 17 × 104 m;
Glass ‘fibrous or filamentary materials’ having either of the following characteristics:
A ‘specific modulus’ exceeding 3,18 × 106 m; or
A ‘specific tensile strength’ exceeding 76,2 × 103 m;
Thermoset resin-impregnated continuous “yarns”, “rovings”, “tows” or ‘tapes’ with a width of 15 mm or less (once prepregs), made from carbon or glass ‘fibrous or filamentary materials’ other than those specified in II.A1.010.a. or b.
Note: This item does not cover ‘fibrous or filamentary materials’ defined in items 1C010.a, 1C010.b, 1C210.a and 1C210.b.
1C010.a
1C010.b
1C210.a
1C210.b
A1.010 |
Resin-impregnated or pitch-impregnated fibres (prepregs), metal or carbon-coated fibres (preforms) or ‘carbon fibre preforms’, as follows:
Made from ‘fibrous or filamentary materials’ specified in II.A1.009 above;
Epoxy resin ‘matrix’ impregnated carbon ‘fibrous or filamentary materials’ (prepregs), specified in 1C010.a, 1C010.b or 1C010.c, for the repair of aircraft structures or laminates, of which the size of individual sheets does not exceed 50 cm × 90 cm;
Prepregs specified in 1C010.a, 1C010.b or 1C010.c, when impregnated with phenolic or epoxy resins having a glass transition temperature (Tg) less than 433 K (160 oC) and a cure temperature lower than the glass transition temperature.
Note: This item does not cover ‘fibrous or filamentary materials’ defined in item 1C010.e.
1C010.e.
1C210
A1.011 | Reinforced silicon carbide ceramic composites usable for nose tips, re-entry vehicles, nozzle flaps, usable in “missiles”, other than those specified in 1C107. | 1C107
A1.012 |
Maraging steels, other than those specified in 1C116 or 1C216, ‘capable of’ an ultimate tensile strength of 2050 MPa or more, at 293 K (20 oC).
The phrase ‘maraging steel capable of’ encompasses maraging steel before or after heat treatment.
1C216
A1.013 |
Tungsten, tantalum, tungsten carbide, tantalum carbide and alloys, having both of the following characteristics:
In forms having a hollow cylindrical or spherical symmetry (including cylinder segments) with an inside diameter between 50 mm and 300 mm; and
A mass greater than 5 kg.
Note: This item does not cover tungsten, tungsten carbide and alloys defined in item 1C226.
1C226
A1.014 | Elemental powders of cobalt, neodymium or samarium or alloys or mixtures thereof containing at least 20 % by weight of cobalt, neodymium or samarium, with a particle size less than 200 μm. | —
A1.015 | Pure tributyl phosphate (TBP) (CAS No 126-73-8) or any mixture having a TBP content of more than 5 % by weight. | —
A1.016 |
‘Maraging steel’, other than those prohibited by 1C116, 1C216 or II.A1.012
‘Maraging steels’ are iron alloys generally characterised by high nickel, very low carbon content and the use of substitutional elements or precipitates to produce strengthening and age-hardening of the alloy.
—
A1.017 |
Metals, metal powders and material as follows:
Tungsten and tungsten alloys, other than those prohibited by 1C117, in the form of uniform spherical or atomized particles of 500 μm diameter or less with a tungsten content of 97 % by weight or more;
Molybdenum and molybdenum alloys, other than those prohibited by 1C117, in the form of uniform spherical or atomized particles of 500 μm diameter or less with a molybdenum content of 97 % by weight or more; or
Tungsten materials in the solid form, other than those prohibited by 1C226, or II.A1.013 having material compositions as follows:
Tungsten and alloys containing 97 % by weight or more of tungsten;
Copper infiltrated tungsten containing 80 % by weight or more of tungsten; or
Silver infiltrated tungsten containing 80 % by weight or more of tungsten.
—
A1.018 |
Soft magnetic alloys having a chemical composition as follows:
Iron content between 30 % and 60 %; or
Cobalt content between 40 % and 60 %.
—
A1.019 |
“Fibrous or filamentary materials” or prepregs, not prohibited by Annex I or by Annex II (under II.A1.009, II.A1.010) of this Regulation, or not specified by Annex I of Regulation (EU) 2021/821, as follows:
Carbon “fibrous or filamentary materials”;
Note: II.A1.019a. does not cover fabrics.
Thermoset resin-impregnated continuous “yarns”, “rovings”, “tows”, or “tapes”, made from carbon “fibrous or filamentary materials”; or
Polyacrylonitrile (PAN) continuous “yarns”, “rovings”, “tows” or “tapes”
—
A2. Materials Processing
No | Description | Related item from Annex I to Regulation (EU) 2021/821
A2.001 |
Vibration test systems, equipment and components thereof, other than those specified in 2B116:
Vibration test systems employing feedback or closed loop techniques and incorporating a digital controller, capable of vibrating a system at an acceleration equal to or greater than 0,1 g rms between 0,1 Hz and 2 kHz and imparting forces equal to or greater than 50 kN, measured ‘bare table’;
‘Vibration test systems incorporating a digital controller’ are those systems, the functions of which are, partly or entirely, automatically controlled by stored and digitally coded electrical signals.
Digital controllers, combined with specially designed vibration test ‘software’, with a real-time bandwidth greater than 5 kHz designed for use with vibration test systems specified in 2B116.a.;
‘Real-time control bandwidth’ means the maximum rate at which a controller can execute complete cycles of sampling, processing data and transmitting control signals.
Vibration thrusters (shaker units), with or without associated amplifiers, capable of imparting a force equal to or greater than 50 kN, measured ‘bare table’, and usable in vibration test systems specified in 2B116.a.; or
Test piece support structures and electronic units designed to combine multiple shaker units in a system capable of providing an effective combined force equal to or greater than 50 kN, measured ‘bare table’, and usable in vibration systems specified in 2B116.a.
‘Bare table’ means a flat table, or surface, with no fixture or fittings.
2B116
A2.002 |
Machine tools and components and numerical controls for machine tools, as follows:
Machine tools for grinding having positioning accuracies with “all compensations available” equal to or less (better) than 15 μm according to ISO 230/2 (1988) or national equivalents along any linear axis;
Note: This item does not cover machine tools for grinding defined in items 2B201.b and 2B001.c.
Components and numerical controls, specially designed for machine tools specified in 2B001, 2B201, or under a.
2B201.b
2B001.c
A2.003 |
Balancing machines and related equipment as follows:
Balancing machines, designed or modified for dental or other medical equipment, having all the following characteristics:
Not capable of balancing rotors/assemblies having a mass greater than 3 kg;
Capable of balancing rotors/assemblies at speeds greater than 12500 rpm;
Capable of correcting imbalance in two planes or more; and
Capable of balancing to a residual specific imbalance of 0,2 g × mm per kg of rotor mass;
Note: II.A2.003 does not control balancing machines designed or modified for dental or other medical equipment.
‘Indicator heads’ designed or modified for use with machines specified in 2B119.a. above.
‘Indicator heads’ are sometimes known as balancing instrumentation.
2B119
A2.004 |
Remote manipulators that can be used to provide remote actions in radiochemical separation operations or hot cells, other than those specified in 2B225, having either of the following characteristics:
A capability of penetrating a hot cell wall of 0,3 m or more (through the wall operation); or
A capability of bridging over the top of a hot cell wall with a thickness of 0,3 m or more (over the wall operation).
2B225
A2.006 |
Furnaces capable of operation at temperatures above 400 oC as follows:
Oxidation furnaces
Controlled atmosphere heat treatment furnaces
Note: This item does not cover tunnel kilns with roller or car conveyance, tunnel kilns with conveyor belt, pusher type kilns or shuttle kilns, specially designed for the production of glass, tableware ceramics or structural ceramics.
2B226
2B227
A2.007 |
“Pressure transducers”, other than those defined in 2B230, capable of measuring absolute pressures at any point in the range 0 to 200 kPa and having both of the following characteristics:
Pressure sensing elements made of or protected by “Materials resistant to corrosion by uranium hexafluoride (UF6)”, and
Having either of the following characteristics:
A full scale of less than 200 kPa and an “accuracy” of better than ± 1 % of full scale; or
A full scale of 200 kPa or greater and an “accuracy” of better than 2 kPa.
2B230
A2.011 |
Centrifugal separators, capable of continuous separation without the propagation of aerosols and manufactured from:
Alloys with more than 25 % nickel and 20 % chromium by weight;
Fluoropolymers;
Glass (including vitrified or enamelled coating or glass lining);
Nickel or alloys with more than 40 % nickel by weight;
Tantalum or tantalum alloys;
Titanium or titanium alloys; or
Zirconium or zirconium alloys.
Note: This item does not cover centrifugal separators defined in item 2B352.c.
2B352.c
A2.012 |
Sintered metal filters made of nickel or nickel alloy with more than 40 % nickel by weight.
Note: This item does not cover filters defined in item 2B352.d.
2B352.d
A2.013 |
Spin-forming machines and flow-forming machines, other than those controlled by 2B009, 2B109 or 2B209, having a roller force of more than 60 kN and specially designed components therefor.
For the purpose of II.A2.013, machines combining the functions of spin-forming and flow-forming are regarded as flow-forming machines.
—
A2.014 |
Liquid-liquid contacting equipment (mixer-settlers, pulsed columns, centrifugal contactors); and liquid distributors, vapour distributors or liquid collectors designed for such equipment where all surfaces that come in direct contact with the chemical(s) being processed are any of the following:
N.B. see also III.A2.008.
Made from any of the following materials:
Alloys with more than 25 % nickel and 20 % chromium by weight;
Fluoropolymers;
Glass (including vitrified or enamelled coating or glass lining);
Graphite or ‘carbon graphite’;
Nickel or alloys with more than 40 % nickel by weight;
Tantalum or tantalum alloys;
Titanium or titanium alloys;
Zirconium or zirconium alloys; or
Niobium (columbium) or niobium alloys; or
Made from both stainless steel and one or more of the materials specified in II.A2.014.a.
‘Carbon graphite’ is a composition consisting of amorphous carbon and graphite, in which the graphite content is 8 % or more by weight.
2B350.e
A2.015 |
Industrial equipment and components, other than those specified in 2B350.d, as follows:
N.B. see also III.A2.009.
Heat exchangers or condensers with a heat transfer surface area greater than 0,05 m2, and less than 30 m2; and tubes, plates, coils or blocks (cores) designed for such heat exchangers or condensers, where all surfaces that come in direct contact with the fluid(s) are any of the following:
Made from any of the following materials:
Alloys with more than 25 % nickel and 20 % chromium by weight;
Fluoropolymers;
Glass (including vitrified or enamelled coating or glass lining);
Graphite or ‘carbon graphite’;
Nickel or alloys with more than 40 % nickel by weight;
Tantalum or tantalum alloys;
Titanium or titanium alloys;
Zirconium or zirconium alloys;
Silicon carbide;
Titanium carbide; or
Niobium (columbium) or niobium alloys; or
Made from both stainless steel and one or more of the materials specified in II.A2.015.a.
Note: This item does not cover vehicle radiators.
The materials used for gaskets and seals and other implementation of sealing functions do not determine the status of control of the heat exchanger.
2B350.d
A2.016 |
Multiple-seal, and seal-less pumps, other than those specified in 2B350.i, suitable for corrosive fluids, with manufacturer’s specified maximum flow-rate greater than 0,6 m3/hour, or vacuum pumps with manufacturer’s specified maximum flow-rate greater than 5 m3/hour [measured under standard temperature (273 K or 0 oC) and pressure (101,3 kPa) conditions]; and casings (pump bodies), preformed casing liners, impellers, rotors or jet pump nozzles designed for such pumps, in which all surfaces that come in direct contact with the chemical(s) being processed are any of the following:
NB. see also III.A2.010.
Made from any of the following materials:
Alloys with more than 25 % nickel and 20 % chromium by weight;
Ceramics;
Ferrosilicon;
Fluoropolymers;
Glass (including vitrified or enamelled coatings or glass lining);
Graphite or ‘carbon graphite’
Nickel or alloys with more than 40 % nickel by weight;
Tantalum or tantalum alloys;
Titanium or titanium alloys;
Zirconium or zirconium alloys;
Niobium (columbium) or niobium alloys; or
Aluminium alloys; or
Made from both stainless steel and one or more of the materials specified in II.A2.016.a.
The materials used for gaskets and seals and other implementation of sealing functions do not determine the status of control of the pump.
2B350.i
A3. Electronics
No | Description | Related item from Annex I to Regulation (EU) 2021/821
A3.001 |
High voltage direct current power supplies having both of the following characteristics:
Capable of continuously producing, over a time period of eight hours, 10 kV or more, with output power of 5 kW or more with or without sweeping; and
Current or voltage stability better than 0,1 % over a time period of four hours.
Note: This item does not cover power supplies defined in items 0B001.j.5 and 3A227.
3A227
A3.002 |
Mass spectrometers, other than those specified in 3A233 or 0B002.g, capable of measuring ions of 200 atomic mass units or more and having a resolution of better than 2 parts in 200, as follows, and ion sources thereof:
Inductively coupled plasma mass spectrometers (ICP/MS);
Glow discharge mass spectrometers (GDMS);
Thermal ionisation mass spectrometers (TIMS);
Electron bombardment mass spectrometers having both of the following features:
A molecular beam inlet system that injects a collimated beam of analyte molecules into a region of the ion source where the molecules are ionised by an electron beam; and
One or more ‘cold traps’ that can be cooled to a temperature of 193 K (– 80 oC);
Not used
Mass spectrometers equipped with a microfluorination ion source designed for actinides or actinide fluorides.
Electron bombardment mass spectrometers in II.A3.002.d. are also known as electron impact mass spectrometers or electron ionisation mass spectrometers.
In II.A3.002.d.2., a ‘cold trap’ is a device that traps gas molecules by condensing or freezing them on cold surfaces. For the purposes of II.A3.002.d.2., a closed-loop gaseous helium cryogenic vacuum pump is not a ‘cold trap’.
3A233
A3.004 |
Frequency changers or generators, other than those specified in 0B001.b.13., usable as a variable or fixed frequency motor drive, having all of the following characteristics:
Multiphase output providing a power of 40 VA or greater;
Operating at a frequency of 600 Hz or more; and
Frequency control better (less) than 0,2 %.