For the purposes of this Annex, the following definitions shall apply:
‘associated GHG emissions’ means the increase in direct and indirect greenhouse gas emissions over the entire lifecycle of the activity which are attributable to its implementation;
‘capital emissions’ means the emissions associated with the construction of facilities and equipment associated with an activity;
‘captured CO2’ means CO2 captured and concentrated from a point source of CO2 or from the atmosphere;
‘capture facility’ means a facility that captures CO2 from the atmosphere or from a biogenic-CO2 containing stream and conditions it to a form that is ready to be transported or stored, including in terms of CO2 purity and pressure;
‘certification period’ means the period between a re-certification audit of an activity and the most recent preceding certification audit or re-certification audit of that activity;
‘CO2 fugitives’ means any irregular or unintended CO2 emissions from sources that are not localised, or are too diverse or not substantial enough to be monitored individually;
‘CO2 venting’ means an intentional release of CO2 occurring for operational or safety reasons;
‘exit point’ means a point at which CO2 is transferred out of the capture facility for the purpose of either transport or storage, which excludes any smokestack, flue or other outlet at the capture facility from which CO2 is released into the atmosphere;
‘fossil CO2’ means CO2 generated from fossil carbon, which is inorganic and organic carbon that is not zero-rated carbon under Commission Implementing Regulation (EU) 2018/2066 [Commission Implementing Regulation (EU) 2018/2066 of 19 December 2018 on the monitoring and reporting of greenhouse gas emissions pursuant to Directive 2003/87/EC of the European Parliament and of the Council and amending Commission Regulation (EU) No 601/2012 (OJ L 334, 31.12.2018, p. 1, ELI: http://data.europa.eu/eli/reg_impl/2018/2066/oj).];
‘permanent geological storage’ means storage of CO2 at a geological storage site permitted under Directive 2009/31/EC;
‘point source of CO2’ means a natural or anthropogenic source of gases that has a CO2 concentration higher than that in the free atmosphere due to the generation of CO2 by an oxidation process or other chemical process or the release of CO2 from some form of storage or containment;
‘useful heat’ means heat generated to satisfy an economically justifiable demand for heat, for heating or cooling purposes.
Only the capture facilities may be operators of DACCS or BioCCS activities.
DACCS and BioCCS activities may transfer all or part of the captured CO2 to storage sites for permanent storage to generate permanent carbon removal units. If part of the captured CO2 is transferred for utilisation or is transferred for storage but recognised under an alternative framework, no permanent carbon removal units will be generated in respect of that fraction of the CO2.
A BCR activity shall consist of biochar production at one or more biochar production facilities that are owned by the same legal entity and that apply the same biochar production technology as each other. Biochar produced at different locations may never be assigned to the same production batch (see Section 2.2.5.1) even if the feedstock and production conditions are similar. Biochar from a single activity may be applied in soils or incorporated in products at several sites.
The biochar production process shall:
heat biomass or biomass fuel to temperatures of at least 350 °C;
be designed with the intention of fully capturing or destroying any methane produced with the biochar;
utilise the co-produced heat for biomass drying or to satisfy another economically justifiable demand for heat, for heating or cooling purposes. As an exception to this rule, mobile biochar facilities may operate without utilisation of produced heat if it would be impractical in their specific context for the heat to be utilised. Certification schemes may provide more detailed requirements on minimum heat utilisation efficiency.
Biochar may be applied to soils to provide permanent carbon storage. Operators of activities where biochar is applied to soils shall ensure that there is no significant risk that the net climate benefit of the BCR is offset by heat absorption due to albedo decreases.
Biochar applied in agricultural and forest soils
Biochar application shall be eligible for certification if it has been, either directly without first intermixing it with any other product, or after intermixing with a matrix consisting of soil or one or more additional soil amendment products in compliance with Article 5 of Regulation (EU) 2019/1009 of the European Parliament and of the Council [Regulation (EU) 2019/1009 of the European Parliament and of the Council of 5 June 2019 laying down rules on the making available on the market of EU fertilising products and amending Regulations (EC) No 1069/2009 and (EC) No 1107/2009 and repealing Regulation (EC) No 2003/2003 (OJ L 170, 25.6.2019, p. 1, ELI: http://data.europa.eu/eli/reg/2019/1009/oj).], or after feeding to animals and recovery as manure:
applied to agricultural soils;
applied to forest soils;
applied to soil in greenhouses.
Total application of biochar to agricultural and forest soils shall be limited to no more than 50 tonnes per hectare cumulatively over time [t/ha], including any forms of biochar application whether or not they are certified and including applications that were made prior to the adoption of this methodology. Operators shall maintain geographically specific application records to enable cumulative application to be monitored.
Biochar applied in soils other than agricultural and forest soils
Biochar application shall be eligible for certification if it has been, either directly without first intermixing it with any other product, or after intermixing with a matrix consisting of soil or other appropriate materials:
used in landscaping, for daily cover at landfill sites or for filling holes, including disused mines and oil wells;
applied to urban soils, including growing media used in flowerbeds or for urban tree planting and in public parks and public or private gardens.
Operators of activities that produce biochar that is used for landscaping, landfill or hole filling shall intermix the biochar with at least one other material prior to application and shall ensure that the intermixture cannot self-sustain combustion.
Only BCR activities that incorporate biochar in cement, concrete or asphalt shall be eligible for certification.
The duration of any activity period for DACCS and BioCCS activities shall not exceed 15 years. At the end of every activity period operators may start a new activity period by submitting a new activity plan.
The monitoring period for DACCS and BioCCS activities shall be the period up until the point at which responsibility for all geological storage sites utilised by the activity has been transferred to the relevant competent national authorities in accordance with Article 18 of Directive 2009/31/EC.
The duration of the certification period for DACCS and BioCCS activities shall not exceed 1 year.
Where it is not possible to precisely identify the period in time during which CO2 captured during a given certification period physically enters permanent storage, operators may estimate emissions associated with transport and storage based on data recorded during the certification period without including in the calculation a temporal delay between the time at which the CO2 was captured and the time at which it is injected, by assessing the average associated emissions (including fugitive emissions, leakage or venting) during transport and storage of CO2 per tonne of CO2 handled during the certification period.
The duration of any activity period for a BCR activity shall not exceed 5 years. At the end of every activity period operators may start a new activity period by submitting a new activity plan.
The monitoring period for BCR activities shall be:
for activities that use biochar by application to soil, where application to soil is directly overseen by the certification body the period up to application, otherwise the period up to one year after the end of the certification period during which the biochar is reported to have been applied to the soil;
for activities that use biochar by incorporation in products, the period up to the point at which it is demonstrated that the biochar has been incorporated.
The certification period for a BCR activity shall not exceed one year. Carbon removals and associated emissions shall be recorded in the certification period in which the CO2 is permanently stored by application of biochar to soils or incorporation of biochar in products.
Before the certification audit, the operator shall submit to the certification body an activity plan that includes the information necessary to assess compliance with the requirements of this methodology, as referred to in the third paragraph.
Where an operator wishes to change the activity plan during the activity period, that operator shall submit a rationale behind the changes to the certification bodies without delay and shall include any adjustment to the initial plan, in particular the recalculation of the expected greenhouse gas (‘GHG’) emissions and removals and impacts on sustainability requirements.
The activity plan shall include:
a general description of the activity, the technologies and the infrastructure to be utilised;
details of all entities of the carbon removal value chain involved in delivery of the activity;
identification and demonstration of compliance of the activity with any relevant local, regional and national laws, statutes and regulatory frameworks;
a list of emission sources and sinks that are relevant to the activity, in accordance with Sections 2.1.1 and 2.2.1;
estimates of total carbon removals and GHG associated emissions of the activity for the activity period, in accordance with points (k), (l) and (m) of Annex II to Regulation (EU) 2024/3012;
a description of any materiality assessment undertaken in accordance with Section 2.3.1;
a description of the assessment of uncertainty, in accordance with Section 2.3.6;
proof of compliance with the minimum sustainability requirements, in accordance with Section 4.1;
funding sources received or applied for with regard to the activity, in accordance with Sections 2.1.2 and 2.2.2;
any other information necessary for the certification body to conduct the certification audit in accordance with Article 9 of Regulation (EU) 2024/3012.
Before the certification audit, operators shall submit a monitoring plan to the certification body. That monitoring plan shall comply with the following criteria:
it shall include a description of the activity to be monitored;
it shall include a description of the procedure for managing the assignment of responsibilities for monitoring and reporting, and for managing the competences of responsible personnel;
it shall include, where applicable, the default values used for calculation factors indicating the source of the factor, or the relevant source, from which the default factor will be retrieved periodically;
it shall include, where applicable, a list of laboratories engaged in carrying out relevant analytical procedures;
it shall include, where measurements are taken, a description of the measurement method including descriptions of all written procedures relevant for the measurement;
it shall include, where applicable, a detailed description of the monitoring methodology where transfer of CO2 is carried out, including a description of continuous measurement systems used and of procedures for preventing, detecting and quantification of leakage events from CO2 transport infrastructure;
it shall apply, where applicable, the minimum frequencies for analysis listed in Annex VII to Implementing Regulation (EU) 2018/2066;
it shall apply the standard for quality assurance laid down in Article 60 of Implementing Regulation (EU) 2018/2066;
it shall include a record keeping requirement for all relevant data and information consistent with the record keeping requirements laid down in Article 67(1) of Implementing Regulation (EU) 2018/2066.
In the case that it is not possible to fully detail the monitoring plan when an operator applies for certification, the monitoring plan shall be submitted as completely as possible, clearly indicating any non-final aspects and providing an indication of how the operator expects these aspects to be addressed. The activity may be certified on this basis provided the certification body accepts that the omissions are properly justified. The monitoring plan shall be finalised and presented to the certification body prior to the first re-certification.
Certification schemes may provide additional guidance on the elements to be included for each type of activity, minimum measurement frequencies for measurements not listed in Annex VII to Implementing Regulation (EU) 2018/2066, and/or best practice requirements for quality assurance.
Operators shall obtain, record, compile, analyse and document monitoring data, including assumptions, references, activity data and calculation factors in a transparent manner that enables the checking of performance achieved during at the various activity stages, and, when requested, report this information to the certification bodies or certification schemes .
Each parameter monitored shall be accompanied with the following information:
entity responsible for collection and archiving;
data source;
equipment, measurement methods and procedures used for monitoring, including details on accuracy and calibration;
monitoring frequency;
quality assessment and quality check procedures.
All measurements shall be conducted with calibrated measurement equipment according to industry standards, following the requirements in Articles 42 of Implementing Regulation (EU) 2018/2066, and any necessary data aggregation shall be undertaken following the requirements in Article 44 of that Implementing Regulation (EU) 2018/2066.
Before each re-certification audit, the operator shall submit to the certification body a monitoring report including the net carbon removal benefit, the total amount of gross carbon removal generated by the activity, the amount of greenhouse gases associated to the activity and all the necessary information relating to the quantification of the net carbon removal benefit and any relevant information on the compliance of the activity with storage, liability and sustainability requirements. In particular, the monitoring report shall include the following:
all the parameters specified in Sections 2.1.5.3, 2.1.6.4, 2.1.7.3, 2.1.8.5, 2.2.5.6, 2.2.6.2 or 2.2.7.3 measured and calculated for the quantification of carbon removals and GHG emissions associated with the activity. All removals and emissions of CO2 and emissions of other GHGs shall be assessed over the certification period that is to be audited and reported in the monitoring report. Emissions of GHGs other than CO2 shall be converted to tonnes of CO2eq by use of the 100-year Global Warming Potentials set out in Annex I to Commission Delegated Regulation (EU) 2020/1044 [Commission Delegated Regulation (EU) 2020/1044 of 8 May 2020 supplementing Regulation (EU) 2018/1999 of the European Parliament and of the Council with regard to values for global warming potentials and the inventory guidelines and with regard to the Union inventory system and repealing Commission Delegated Regulation (OJ L 230, 17.7.2020, p. 1, ELI: http://data.europa.eu/eli/reg_del/2020/1044/oj).];
the biomass feedstock or feedstock mix consumed as required under Section 4.2(a)(ii);
the quantity of carbon farming sequestration units that have been purchased in accordance with Section 4.3.3;
financing received or applied for with regard to the activity, in accordance with Sections 2.1.2 and 2.2.2;
for BCR activities, the results of laboratory analyses required in Sections 4.4.1, 4.4.2 and 4.4.3.
DACCS or BioCCS activities shall consider the GHG sources and sinks included in Table 1.
Phase of the activity | Emission sources and sinks | Gases included
CO2 capture | Capture facility: Operation of equipment used to capture CO2 from the ambient air or from biogenic emissions, including equipment used to generate airflow, and equipment associated with regeneration processes to recover the fluids or other media used in the carbon capture process. | Greenhouse gases
Capture facility: Any CO2 conditioning equipment used to further process the CO2 stream before transfer to transport or storage infrastructure. | Greenhouse gases
Capture facility: Any associated energy generation equipment powering the capture process that is under the control of the operator of the capture facility. | Greenhouse gases
Capture facility: Any treatment equipment for processing wastes or byproducts of the carbon capture process. | Greenhouse gases
Capture facility: Fuel combustion, electricity consumption, heat consumption. | Greenhouse gases
Biomass supply: Emissions associated with additional biomass, biofuels, bioliquids and biomass fuels consumed for the operation of the capture facility (e.g. emissions for the harvest or transport of biomass). | Greenhouse gases
Input emissions: Production and supply of inputs used by the capture facility. | Greenhouse gases
Waste treatment: Processing and treatment of any wastes (including wastewater and exhaust gases) generated by the capture facility. | Greenhouse gases
Capital emissions: Emissions associated with the construction and installation of the capture facility. | Greenhouse gases
Transport of CO2 | Transportation: Fuel consumption and electricity consumption of road and rail transportation, maritime transportation and other vehicles. | Greenhouse gases
Infrastructure: Fuel consumption, electricity consumption and heat consumption in infrastructure and buildings functionally connected to the pipeline transport network (e.g. booster/compressor stations, heaters, CO2 hubs, intermediate storage). | Greenhouse gases
Losses: CO2 fugitive, vented, and leakage emissions from the transport network. | CO2 only
Injection at the geological storage site | Storage site: Removal by CO2 injection. | CO2 only
Storage site: Fuel consumption, electricity consumption, heat consumption. | Greenhouse gases
Losses: CO2 fugitive and vented emissions from injection and from the storage site prior to entering permanent geological storage. | CO2 only
Input emissions: Production and supply of any inputs used by the storage site. | Greenhouse gases
Waste treatment: Processing and treatment of any wastes (including wastewater and exhaust gases) generated by the storage site. | Greenhouse gases
Capital emissions: Emissions associated with the construction and installation of the storage site. | Greenhouse gases
A standardised baseline set to 0 tonnes of CO2 per year [tCO2/year] shall apply for DACCS and BioCCS activities.
Where the activity is financed through a combination of public and private funding when submitting the activity plan to the certification scheme, operators shall indicate any form of public financing received or applied for with regard to the activity. This information shall be included in the certificate of compliance.
Operators may use one of two approaches for the calculation of the total carbon removal (CRtotal), either the approach specified in Section 2.1.3.3 or that in Section 2.1.3.4, depending on whether the CO2 captured by the activity would be kept fully segregated from CO2 from other sources through the transport infrastructure and at the storage site.
A capture facility may capture CO2 that is:
solely atmospheric or biogenic CO2;
a combination of biogenic CO2 and fossil CO2 from a mixed CO2 stream;
fossil CO2 captured from a process associated with the capture process.
The fractions of CO2 captured by the activity shall be given the following designations.
The total amount of CO2 captured at the capture facility and transferred for transport or storage shall be designated CO2captured,total and calculated in accordance with equation [1].
CO2captured,total
i
CO2OUT,activity,i | [1]
where:
CO2OUT,activity,i | = | minus the amount of CO2 from the capture activity leaving the capture facility at each exit point i, which shall be measured.
Any leakage of CO2 occurring between the point of capture and the point of leaving the capture facility is implicitly excluded from the term CO2captured,total.
The amount of atmospheric or biogenic CO2 that is captured at the capture facility and is transferred for transport or storage shall be designated CO2captured,atmobio and shall be calculated in accordance with equation [2].
CO2captured,atmobioCO2captured,total – CO2captured, fossil | [2]
where:
CO2captured, total | = | is defined in equation [1];
CO2captured, fossil | = | is defined in equation [3].
In some activities, fossil CO2 will be captured alongside CO2 of atmospheric or biogenic origin. Where fossil CO2 is emitted as a result of the capture process it may be captured, either separately from the capture of CO2 of atmospheric or biogenic origin (‘separate capture’) or simultaneously with the capture of CO2 of atmospheric or biogenic origin (‘co-capture’). If it is then permanently stored it may be excluded from the calculation of GHGassociated. For BioCCS activities only it is also permissible to capture CO2 from a mixed stream consisting of a combination of biogenic CO2 and fossil CO2. Fossil CO2 captured from the capture process is associated with the activity, and emissions from transporting and storing that CO2 shall be included in GHGassociated. Fossil CO2 captured from a mixed stream by a BioCCS activity is not associated with the activity, and emissions from transporting and storing that CO2 shall not be included in GHGassociated. The amount of fossil CO2 that is captured at the capture facility shall be calculated in accordance with equation [3].
CO2captured,fossilCO2captured,fossil,assoc + CO2captured,fossil, mixed | [3]
where:
CO2captured,fossil,assoc | = | minus the amount of fossil CO2 emitted as a result of the capture process that is captured, calculated using equation [4];
CO2captured,fossil, mixed | = | minus the amount of fossil CO2 captured from a mixed stream as part of a BioCCS activity, calculated using equation [5].
The amount of CO2 emitted as a result of the capture process that is captured, CO2captured,fossil,assoc, shall be determined in accordance with equation [4] as the sum of the separately captured and co-captured components.
CO2captured,fossil,assocCO2fossil,assoc,co – captured +
sources
CO2fossil,assoc,source | [4]
where: