2 ANNEX II STATISTICAL TESTING PROCEDURE TO VERIFY THE FUEL CONSUMPTION AND DISTANCE DETERMINED BY THE OBFCM DEVICE, Regulation (EU) 2025/2161

In forcesince 27 Oct 2025

1.1. This Annex sets out the statistical testing procedure to verify the accuracy of the total fuel consumption and total distance as determined by the OBFCM device.

The vehicle shall be selected from the OBFCM family which exceeded the accuracy requirements in any of the monitoring tests set out in point 4.2. of Annex I, or from the OBFCM family that was selected by the granting approval authority based on a suspicion of non-compliance. A minimum of 3 and maximum of 8 vehicles shall be selected from this family for testing.

Vehicle conditions are described in point 4 of Annex Xa to Regulation (EU) 2017/2400. For the fuel consumption measurement as described in point 6.1.5.5 of Annex Xa to Regulation (EU) 2017/2400, the fuel used shall be the one set out in point 2.3 of this Annex.

The test procedure shall be performed with a reference fuel specified in Annex IX to Regulation (EU) No 582/2011 on which the parent engine has been type-approved under that Regulation.

The actual fuel mass consumed shall be measured on-board with a measurement device as set out in point 5.7 of Annex Xa to Regulation (EU) 2017/2400. If a run-in phase took place in accordance with point 6.1.2 of that Annex Xa, the vehicle shall be equipped with the fuel consumption measurement system after the run-in phase.

The vehicle preparation is described in points 6.1.2, 6.1.3, and 6.1.4 of Annex Xa to Regulation (EU) 2017/2400. The vehicle shall be equipped with the fuel measurement system as specified in point 5.7 of that Annex.

The vehicle tested shall be equipped with the on-board fuel consumption device as type-approved for that vehicle family.

Before start of statistical verification test sequence the vehicle may be driven for warm up in accordance with Table 3 of Annex Xa to Regulation (EU) 2017/2400. The warm up phase shall not be considered in the evaluation of the verification test.

The fuel measurement signals to be measured are described in point 5.9 in Annex Xa to Regulation (EU) 2017/2400. Those include the ‘fuel mass flow for liquid fuels’, ‘fuel mass flow for gaseous fuels’.

The engine fuel rate signals as determined by the OBFCM device shall also be recorded.

The recorded vehicle speed shall be the CAN signal for vehicle speed in the unit km/h as provided by a digital tachograph complying with Regulation (EU) No 165/2014 of the European Parliament and of the Council [Regulation (EU) No 165/2014 of the European Parliament and of the Council of 4 February 2014 on tachographs in road transport, repealing Council Regulation (EEC) No 3821/85 on recording equipment in road transport and amending Regulation (EC) No 561/2006 of the European Parliament and of the Council on the harmonisation of certain social legislation relating to road transport (OJ L 60, 28.2.2014, p. 1, ELI: http://data.europa.eu/eli/reg/2014/165/oj).].

The longitudinal and latitudinal position shall be provided via a global positioning system.

Required accuracy:

Position: < 3 m 95 % Circular Error Probable

Update rate: ≥ 4 Hz

Required accuracy: ± 1 °C

Update rate: ≥ 1 Hz

The fuel consumption measurement shall start at vehicle stand still directly before the measuring run. The vehicle shall be driven during the measurement in a driving style avoiding unnecessary braking of the vehicle, gas pedal pumping and aggressive cornering. The setting for the advanced driver assistance systems which is activated automatically at key-on shall be used, and gear shifts shall be performed by the automated system (in the case of AMT or APT transmissions) and the cruise control shall be used (if applicable). The duration of the fuel consumption measurement shall be within the tolerances set out in Table 3 of Annex Xa to Regulation (EU) 2017/2400. The fuel consumption measurement shall end at vehicle stand still directly after the measuring run.

The recording of the total distance travelled (lifetime), total fuel consumed (lifetime) (kilograms), vehicle fuel rate, engine fuel rate, as determined by the OBFCM device, shall start no later than when the fuel consumption measurement has started and end together with the fuel consumption measurement.

The odometer reading shall be taken at vehicle stand still directly before the measuring run and shall be taken at vehicle stand still directly after the end of the fuel consumption measurement.

The route selected shall fulfil the requirements described in point 6.1.5.1 of Annex Xa to Regulation (EU) 2017/2400.

The boundary conditions to be met for a valid verification test are set out in point 6.1.5.7 of Annex Xa to Regulation (EU) 2017/2400.

The recorded data shall be synchronised and aligned to 1 Hz temporal resolution, either by arithmetical average, nearest neighbour or linear interpolation.

The fuel consumption from the OBFCM device shall be compared with the fuel consumption measured on-board with a measurement device reporting the total amount of fuel consumed in grams.

The accuracy ratio COBFCM,FUEL shall be calculated as follows:

COBFCM,FUELFuel_ConsumedTESTkgFuel_ConsumedOBFCMkg

where:

Fuel_ConsumedTEST is the fuel consumption measured during the statistical test procedure, in accordance with point 2.5.3.

Fuel_ConsumedOBFCM is the fuel consumption measured by the OBFCM device during the statistical test, as specified in point 2.5.4, and calculated by taking the difference between the total fuel consumed (lifetime) reading from the OBFCM device at the end of the test and the total fuel consumed (lifetime) reading from the OBFCM device at the start.

This ratio shall be calculated for each of the statistical tests and shall be used to perform the statistical evaluation as set out in point 3.

The accuracy ratio COBFCM,DISTANCE shall be calculated as follows:

COBFCM,DISTANCE

DOBFCM

DODOMETER

where:

DODOMETER is the difference between the odometer reading at the end of the test and the odometer reading at the start of the test referred to in point 2.5.4.

DOBFCM is the difference between the lifetime distance reading from the OBFCM device at the end of the test and the lifetime distance reading from the OBFCM device at the start of the test as recorded in point 2.5.4.

That ratio shall be calculated for each of the statistical tests, and shall be used to perform the statistical evaluation as set out in point 3.

The lifetime distance of the OBFCM device shall be compared with the distance read from the odometer, and in the case of a discrepancy over ± 5 %, the manufacturer shall provide an explanation of that discrepancy to the approval authority, which shall notify the Commission of the discrepancy and the explanation thereto.

The starting point for the statistical evaluation are the values for COBFCM calculated for 3 individual test vehicles (N = 3) in accordance with point 2.6.1 for fuel consumption and in accordance with point 2.6.2 for the total distance.

The criteria set out under point 3.3(3) determine if additional vehicles need to be tested, which shall be verified separately for fuel consumption and total distance.

For the total number of vehicles tested (N), the average (Xtests) and the standard deviation (s) of the test results shall be determined:

Xtests

x1 + x2 + … + xN

N

and

sx1 – Xtests2+ x2 – Xtests2+ … + xN – Xtests2N – 1

where:

xi is the value COBFCM calculated for the individual test vehicle i according to point 2.6.1 of this Annex for fuel consumption, and according to point 2.6.2 of this Annex for the total distance.

For the 3 vehicles initially tested and after each additional vehicle tested, the value Xtests shall be assessed as set out below in order to reach one of the following conclusions for the in-service verification family or road load family concerned:

(1)

Pass the family if:

Xtests ≤ A – tP × s

(2)

Fail the family if:

Xtests > A + tF × s

(3)

Test an additional vehicle if:

A – tP × s < Xtests ≤ A + tF × s

where:

tP and tF are as set out in the table below.

s is the standard deviation determined in accordance with point 3.2.

A is 1,03.

[Where s is the standard deviation determined in accordance with point 3.2. In the case where the standard deviation s is equal to zero, then the value used for tF will be 1,1060.]

Number of vehicles tested | tP | tF

3 | 1,5889 | Highest value of 1,1060 and (0,02/s)

4 | 0,9279 | 0,5068

5 | 0,6117 | 0,2836

6 | 0,3758 | 0,1528

7 | 0,1734 | 0,0646

8 | 0,0000 | 0,0000

For the calculation of the size of the deviation, the average (COBFCM) is defined as Xtests for the total number of vehicles tested, after the family has failed according to point 3:

average (COBFCM) = X tests