, Decision_act (EU) 2025/2355

In forcesince 13 Nov 2025
(2)

The 66 European Assessment Documents relate to the following references for construction products:

balcony and terrace glazing systems without vertical frames (superseding technical specification ‘EAD 020002-00-0404’);

external thermal insulation composite systems with rendering system (superseding technical specification ‘EAD 040083-00-0404’);

factory-made products of extruded, foamed polyethylene terephthalate for thermal insulation;

veture kits – prefabricated units for external wall insulation and their fixing devices (superseding technical specification ‘EAD 040914-00-0404’);

kits made of insulation boards with protective finishing for inverted roofs;

pre-wall mounting kits for windows and doors;

thermal insulation elements of fibre-reinforced polymer which form a thermal break between structural elements;

load-bearing thermal insulation elements which form a thermal break between balconies and internal floors (superseding technical specification ‘EAD 050001-00-0301’);

spherical and cylindrical bearings with special sliding material made of ultra-high-molecular-weight polyethylene (superseding technical specification ‘EAD 050004-00-0301’);

spherical and cylindrical bearings with special sliding material made of fluoropolymer (superseding technical specification ‘EAD 050009-00-0301’);

pre-assembled drainage panels made of gabions and geotextile;

kits composed by subframe and fixings for fastening claddings and external wall elements (superseding technical specification ‘EAD 090034-00-0404’);

variant: kits for external wall claddings mechanically fixed – extension of scope;

glass-ceramic panels for external cladding;

full-bodied sintered stone slabs for use in claddings, floorings, pavings, stairs, rainscreens and curtain walling kits;

kits for self-supporting and interconnected ventilated cavity walls;

wood-based composite panel for facades;

rigid seismic sway brace for fire sprinkler pipe work;

flexible plug expansion joints for road bridges with flexible filling based on a synthetic polymer as binder (superseding technical specification ‘EAD 120011-00-0107’);

wood and metal lighting columns;

glued laminated veneer lumber;

glulam strengthened by laminated veneer lumber, glued laminated veneer lumber made of finger-jointed laminations and block-glued glulam made thereof;

special cements – carbonation hardening cements requiring a particular curing process;

blended cements with high filler content, ground granulated blast-furnace slag or pozzolanic material or both, and clinker;

kits for the strengthening of concrete elements by externally bonded and near-surface-mounted carbon fibre-reinforced polymer strips (superseding technical specification ‘EAD 160086-00-0301’);

couplers for mechanical splices of reinforcing steel bars (superseding technical specification ‘EAD 160129-00-0301’);

stud connectors for anchoring in reinforced concrete members as well as for connecting steel members with reinforced concrete members;

compressed solid earth blocks with or without lime or cement and wall kits made of these blocks and natural hydraulic lime mortar;

column shoes for structural connections of reinforced concrete columns;

structural hollow sections of weathering steel;

fiber ropes with end connectors;

thin metal composite sheets (superseding technical specification ‘EAD 210046-00-1201’);

variant: assessment of components for wood-based composite panels not produced by the manufacturers themselves;

non-load-bearing polyvinyl chloride panels for internal and external walls;

low-bitumen-mass shingles, laminated or not, with mineral or synthetic reinforcement (superseding technical specification ‘EAD 220020-00-0402’);

fastening screws with welded or cold-formed set screws;

fixing clips and sliding clips for double standing seam roof;

variant: road marking products – extension of scope;

variant: compound for bitumen and bituminous mixtures based on crumb rubber powder – extension of scope;

stone wool elements used for large-scale water storage in civil works;

adhesives for wall claddings;

products for installation systems for supporting technical building equipment;

variant: anchor channels under fatigue cyclic shear with different lower load level;

variant: anchor channels for controlled impact screwdrivers;

mechanical fasteners for use in concrete (superseding technical specification ‘EAD 330232-01-0601’);

post–installed fasteners in concrete under fatigue cyclic loading (superseding technical specification ‘EAD 330250-00-0601’);

variant: plastic anchors for redundant non-structural systems in concrete and masonry, and for fixing façade claddings through angle brackets under seismic actions in concrete and masonry;

screw anchors for use in masonry;

variant: cast-in anchor bolts under fatigue or seismic actions;

high-strength structural bolting assemblies for hydraulically operated, friction-less and torsion-free tightening;

anchor devices for fastening personal fall protection systems to timber substructures (superseding technical specification ‘EAD 331846-00-0603’);

distance-fixing systems for use in concrete and masonry;

kits for connection of precast concrete façade elements to concrete structures based on anchor channels;

support fixing assemblies;

point fastening kits for roof panels;

anchor devices for fastening personal fall protection systems to steel or aluminium trapezoidal sheeting substructures;

permanent insulating shuttering kits for whole buildings;

load-bearing sandwich panels with foam or polymeric core and skins of structural cement bonded particle boards;

earthquake-resistant kits composed of steel-concrete composite beams, columns and beam-column joints;

variant: non-load-bearing permanent shuttering kits or systems based on hollow blocks or panels of insulating materials and sometimes concrete: hollow blocks resistant to seismic actions;

fibre-reinforced polymer kits made of a pultruded carbon fibre laminate and an epoxy adhesive;

fibre-reinforced polymer kits made of a carbon or glass fabric and an epoxy resin;

structural steel composite wall panels for building systems;

high load-bearing and low load-bearing single anchor earth retaining structures made of steel;

fire-resistant reactive air transfer grilles;

caps with intumescent inlay for recessed luminaires in fire-resistant suspended ceilings.