This Annex applies without prejudice to Directive 2008/98/EC.
This Annex consists of two parts. Article 39 further refers to the list of waste as referred to in Article 7 of Directive 2008/98/EC. For the purposes of this Regulation and to determine whether a specific waste is covered by the export prohibition in Article 39 of this Regulation, the list of waste as referred to in Article 7 of Directive 2008/98/EC applies only when List A of Part 1 of this Annex is not applicable. If a waste is not listed in List A of Part 1 of this Annex, and not listed as a hazardous waste in the list of waste as referred to in Article 7 of Directive 2008/98/EC, only then it must be checked if it is listed in Part 2 of this Annex.
Wastes listed in List B of Part 1 or which are among the non-hazardous waste listed in the list of waste as referred to in Article 7 of Directive 2008/98/EC (i.e. wastes not marked with an asterisk) are covered by the export prohibition if they are contaminated by other materials to an extent which:
increases the risks associated with the wastes sufficiently to render it appropriate for submission to the procedure of prior written notification and consent, when taking into account the list of waste referred to in Article 7 of Directive 2008/98/EC as well as the hazardous properties listed in Annex III to that Directive; or
prevents the recovery of the waste in an environmentally sound manner.
A1
Metal and metal-bearing wastes
A1010
Metal wastes and waste consisting of alloys of any of the following:
Antimony
Arsenic
Beryllium
Cadmium
Lead
Mercury
Selenium
Tellurium
Thallium
but excluding such wastes specifically listed on list B.
A1020
Waste having as constituents or contaminants, excluding metal waste in massive form, any of the following:
Antimony; antimony compounds
Beryllium; beryllium compounds
Cadmium; cadmium compounds
Lead; lead compounds
Selenium; selenium compounds
Tellurium; tellurium compounds
A1030
Wastes having as constituents or contaminants any of the following:
Arsenic; arsenic compounds
Mercury; mercury compounds
Thallium; thallium compounds
A1040
Wastes having as constituents any of the following:
Metal carbonyls
Hexavalent chromium compounds
A1050
Galvanic sludges
A1060
Waste liquors from the pickling of metals
A1070
Leaching residues from zinc processing, dust and sludges such as jarosite, hematite, etc.
A1080
Waste zinc residues not included on list B, containing lead and cadmium in concentrations sufficient to exhibit Annex III characteristics
A1090
Ashes from the incineration of insulated copper wire
A1100
Dusts and residues from gas cleaning systems of copper smelters
A1110
Spent electrolytic solutions from copper electrorefining and electrowinning operations
A1120
Waste sludges, excluding anode slimes, from electrolyte purification systems in copper electrorefining and electrowinning operations
A1130
Spent etching solutions containing dissolved copper
A1140
Waste cupric chloride and copper cyanide catalysts
A1150
Precious metal ash from incineration of printed circuit boards not included on list B [Note that mirror entry on list B (B1160) does not specify exceptions.]
A1160
Waste lead-acid batteries, whole or crushed
A1170
Unsorted waste batteries excluding mixtures of only list B batteries. Waste batteries not specified on list B containing Annex I constituents to an extent to render them hazardous.
A1181
Electrical and electronic waste (note the related entry Y49 in List A of Part 2 in Annex V):
Waste electrical and electronic equipment
containing or contaminated with cadmium, lead, mercury, organohalogen compounds or other Annex I constituents to an extent that the waste exhibits an Annex III characteristic, or
with a component containing or contaminated with Annex I constituents to an extent that the component exhibits an Annex III characteristic, including but not limited to any of the following components:
glass from cathode-ray tubes included on list A
a battery included on list A
a switch, lamp, fluorescent tube or a display device backlight which contains mercury
a capacitor containing PCBs
a component containing asbestos
certain circuit boards
certain display devices
certain plastic components containing a brominated flame retardant
Waste components of electrical and electronic equipment containing or contaminated with Annex I constituents to an extent that the waste components exhibit an Annex III characteristic, unless covered by another entry on list A
Wastes arising from the processing of waste electrical and electronic equipment or waste components of electrical and electronic equipment, and containing or contaminated with Annex I constituents to an extent that the waste exhibits an Annex III characteristic (e.g. fractions arising from shredding or dismantling), unless covered by another entry on list A
A1190
Waste metal cables coated or insulated with plastics containing or contaminated with coal tar, PCB [PCBs are at a concentration level of 50 mg/kg or more.], lead, cadmium, other organohalogen compounds or other Annex I constituents, to the extent that they exhibit Annex III characteristics
A2
Wastes containing principally inorganic constituents, which may contain metals and organic materials
A2010
Glass waste from cathode-ray tubes and other activated glasses
A2020
Waste inorganic fluorine compounds in the form of liquids or sludges but excluding such wastes specified on list B
A2030
Waste catalysts but excluding such wastes specified on list B
A2040
Waste gypsum arising from chemical industry processes, when containing Annex I constituents to the extent that it exhibits an Annex III hazardous characteristic (note the related entry on list B, B2080)
A2050
Waste asbestos (dusts and fibres)
A2060
Coal-fired power plant fly-ash containing Annex I substances in concentrations sufficient to exhibit Annex III characteristics (note the related entry on list B, B2050)
A3
Wastes containing principally organic constituents, which may contain metals and inorganic materials
A3010
Waste from the production or processing of petroleum coke and bitumen
A3020
Waste mineral oils unfit for their originally intended use
A3030
Wastes that contain, consist of or are contaminated with leaded anti-knock compound sludges
A3040
Waste thermal (heat transfer) fluids
A3050
Wastes from production, formulation and use of resins, latex, plasticizers, glues/adhesives excluding such wastes specified on list B (note the related entry on list B, B4020)
A3060
Waste nitrocellulose
A3070
Waste phenols, phenol compounds including chlorophenol in the form of liquids or sludges
A3080
Waste ethers not including those specified on list B
A3090
Waste leather dust, ash, sludges and flours when containing hexavalent chromium compounds or biocides (note the related entry on list B, B3100)
A3100
Waste paring and other waste of leather or of composition leather not suitable for the manufacture of leather articles containing hexavalent chromium compounds or biocides (note the related entry on list B, B3090)
A3110
Fellmongery wastes containing hexavalent chromium compounds or biocides or infectious substances (note the related entry on list B, B3110)
A3120
Fluff — light fraction from shredding
A3130
Waste organic phosphorous compounds
A3140
Waste non-halogenated organic solvents but excluding such wastes specified on list B
A3150
Waste halogenated organic solvents
A3160
Waste halogenated or unhalogenated non-aqueous distillation residues arising from organic solvent recovery operations
A3170
Wastes arising from the production of aliphatic halogenated hydrocarbons (such as chloromethane, dichloro-ethane, vinyl chloride, vinylidene chloride, allyl chloride and epichlorhydrin)
A3180
Wastes, substances and articles containing, consisting of or contaminated with polychlorinated biphenyl (PCB), polychlorinated terphenyl (PCT), polychlorinated naphthalene (PCN) or polybrominated biphenyl (PBB), or any other polybrominated analogues of these compounds, at a concentration level of 50 mg/kg or more [The 50 mg/kg level is considered to be an internationally practical level for all wastes. However, many individual countries have established lower regulatory levels (e.g. 20 mg/kg) for specific wastes.]
A3190
Waste tarry residues (excluding asphalt cements) arising from refining, distillation and any pyrolitic treatment of organic materials
A3200
Bituminous material (asphalt waste) from road construction and maintenance, containing tar (note the related entry on list B B2130)
A3210
Plastic waste, including mixtures of such waste, containing or contaminated with Annex I constituents, to an extent that it exhibits an Annex III characteristic (note the related entry B3011, in list B of this Part, and entry Y48, in list A of Part 2)
A4
Wastes which may contain either inorganic or organic constituents
A4010
Wastes from the production, preparation and use of pharmaceutical products but excluding such wastes specified on list B
A4020
Clinical and related wastes; that is wastes arising from medical, nursing, dental, veterinary, or similar practices, and wastes generated in hospitals or other facilities during the investigation or treatment of patients, or research projects
A4030
Wastes from the production, formulation and use of biocides and phytopharmaceuticals, including waste pesticides and herbicides that are off-specification, out-dated [‘Out-dated’ means unused within the period recommended by the manufacturer.], or unfit for their originally intended use
A4040
Wastes from the manufacture, formulation and use of wood-preserving chemicals [This entry does not include wood treated with wood-preserving chemicals.]
A4050
Wastes that contain, consist of or are contaminated with any of the following:
Inorganic cyanides, excepting precious-metal-bearing residues in solid form containing traces of inorganic cyanides
Organic cyanides
A4060
Waste oils/water, hydrocarbons/water mixtures, emulsions
A4070
Wastes from the production, formulation and use of inks, dyes, pigments, paints, lacquers, varnish excluding any such waste specified on list B (note the related entry on list B, B4010)
A4080
Wastes of an explosive nature (but excluding such wastes specified on list B)
A4090
Waste acidic or basic solutions, other than those specified in the corresponding entry on list B (note the related entry on list B, B2120)
A4100
Wastes from industrial pollution control devices for cleaning of industrial off-gases but excluding such wastes specified on list B
A4110
Wastes that contain, consist of or are contaminated with any of the following:
any congenor of polychlorinated dibenzo-furan
any congenor of polychlorinated dibenzo-dioxin
A4120
Wastes that contain, consist of or are contaminated with peroxides
A4130
Waste packages and containers containing Annex I substances in concentrations sufficient to exhibit Annex III hazard characteristics
A4140
Waste consisting of or containing off-specification or out-dated [‘Out-dated’ means unused within the period recommended by the manufacturer.] chemicals corresponding to Annex I categories and exhibiting Annex III hazard characteristics
A4150
Waste chemical substances arising from research and development or teaching activities which are not identified and/or are new and whose effects on human health and/or the environment are not known
A4160
Spent activated carbon not included on list B (note the related entry on list B, B2060)
B1
Metal and metal-bearing wastes
B1010
Metal and metal-alloy wastes in metallic, non-dispersible form:
Precious metals (gold, silver, the platinum group, but not mercury)
Iron and steel scrap
Copper scrap
Nickel scrap
Aluminium scrap
Zinc scrap
Tin scrap
Tungsten scrap
Molybdenum scrap
Tantalum scrap
Magnesium scrap
Cobalt scrap
Bismuth scrap
Titanium scrap
Zirconium scrap
Manganese scrap
Germanium scrap
Vanadium scrap
Scrap of Hafnium, Indium, Niobium, Rhenium and Gallium
Thorium scrap
Rare earths scrap
Chromium scrap
B1020
Clean, uncontaminated metal scrap, including alloys, in bulk finished form (sheet, plate, beams, rods, etc.):
Antimony scrap
Beryllium scrap
Cadmium scrap
Lead scrap (but excluding lead-acid batteries)
Selenium scrap
Tellurium scrap
B1030
Refractory metals containing residues
B1031
Molybdenum, tungsten, titanium, tantalum, niobium and rhenium metal and metal alloy wastes in metallic dispersible form (metal powder), excluding such wastes as specified in list A under entry A1050, Galvanic sludges.
B1040
Scrap assemblies from electrical power generation not contaminated with lubricating oil, PCB or PCT to an extent to render them hazardous
B1050
Mixed non-ferrous metal, heavy fraction scrap, not containing Annex I materials in concentrations sufficient to exhibit Annex III characteristics [Note that even where low level contamination with Annex I materials initially exists, subsequent processes, including recycling processes, may result in separated fractions containing significantly enhanced concentrations of those Annex I materials.]
B1060
Waste selenium and tellurium in metallic elemental form including powder
B1070
Waste of copper and copper alloys in dispersible form, unless they contain Annex I constituents to an extent that they exhibit Annex III characteristics
B1080
Zinc ash and residues including zinc alloys residues in dispersible form unless containing Annex I constituents in concentration such as to exhibit Annex III characteristics or exhibiting hazard characteristic H4.3 [The status of zinc ash is currently under review and there is a recommendation with United Nations Conference on Trade and Development (Unctad) that zinc ashes should not be dangerous goods.]
B1090
Waste batteries conforming to a specification, excluding those made with lead, cadmium or mercury
B1100
Metal-bearing wastes arising from melting, smelting and refining of metals:
Hard zinc spelter
Zinc-containing drosses:
Galvanizing slab zinc top dross (> 90 % Zn)
Galvanizing slab zinc bottom dross (> 92 % Zn)
Zinc die casting dross (> 85 % Zn)
Hot dip galvanizers slab zinc dross (batch) (> 92 % Zn)
Zinc skimmings
Aluminium skimmings (or skims) excluding salt slag
Slags from copper processing for further processing or refining not containing arsenic, lead or cadmium to an extent that they exhibit Annex III hazard characteristics
Wastes of refractory linings, including crucibles, originating from copper smelting
Slags from precious metals processing for further refining
Tantalum bearing tin slags with less than 0,5 % tin
B1110
Electrical and electronic assemblies:
Electronic assemblies consisting only of metals or alloys
Waste electrical and electronic assemblies or scrap [This entry does not include scrap from electrical power generation.] (including printed circuit boards) not containing components such as accumulators and other batteries included on list A, mercury-switches, glass from cathode-ray tubes and other activated glass and PCB-capacitors, or not contaminated with Annex I constituents (e.g. cadmium, mercury, lead, polychlorinated biphenyl) or from which these have been removed, to an extent that they do not possess any of the characteristics contained in Annex III (note the related entry on list A, A1180)
Electrical and electronic assemblies (including printed circuit boards, electronic components and wires) destined for direct re-use [Re-use can include repair, refurbishment or upgrading, but not major reassembly.] and not for recycling or final disposal [In some countries, these materials destined for direct re-use are not considered wastes.]
B1115
Waste metal cables coated or insulated with plastics, not included in entry A1190, excluding those destined for Annex IVA operations or any other disposal operations involving, at any stage, uncontrolled thermal processes, such as open-burning
B1120
Spent catalysts excluding liquids used as catalysts, containing any of:
| Transition Metals, excluding waste catalysts (spent catalysts, liquid used catalysts or other catalysts) on list A |
Scandium
Vanadium
Manganese
Cobalt
Copper
Yttrium
Niobium
Hafnium
Tungsten
Titanium
Chromium
Iron
Nickel
Zinc
Zirconium
Molybdenum
Tantalum
Rhenium
| Lanthanides (rare earth metals): |
Lanthanum
Praseodymium
Samarium
Gadolinium
Dysprosium
Erbium
Ytterbium
Cerium
Neodymium
Europium
Terbium
Holmium
Thulium
Lutetium
B1130
Cleaned spent precious-metal-bearing catalysts
B1140
Precious-metal-bearing residues in solid form, which contain traces of inorganic cyanides
B1150
Precious metals and alloy wastes (gold, silver, the platinum group, but not mercury) in a dispersible, non-liquid form with appropriate packaging and labelling
B1160
Precious-metal ash from the incineration of printed circuit boards (note the related entry on list A, A1150)
B1170
Precious-metal ash from the incineration of photographic film
B1180
Waste photographic film containing silver halides and metallic silver
B1190
Waste photographic paper containing silver halides and metallic silver
B1200
Granulated slag arising from the manufacture of iron and steel
B1210
Slag arising from the manufacture of iron and steel including slags as a source of TiO2 and vanadium
B1220
Slag from zinc production, chemically stabilized, having a high iron content (above 20 %) and processed according to industrial specifications (e.g. DIN 4301) mainly for construction
B1230
Mill scaling arising from the manufacture of iron and steel
B1240
Copper oxide mill-scale
B1250
Waste end-of-life motor vehicles, containing neither liquids nor other hazardous components
B2
Wastes containing principally inorganic constituents, which may contain metals and organic materials
B2010
Wastes from mining operations in non-dispersible form:
Natural graphite waste
Slate waste, whether or not roughly trimmed or merely cut, by sawing or otherwise
Mica waste
Leucite, nepheline and nepheline syenite waste
Feldspar waste
Fluorspar waste
Silica wastes in solid form excluding those used in foundry operations
B2020
Glass waste in non-dispersible form:
Cullet and other waste and scrap of glass except for glass from cathode-ray tubes and other activated glasses
B2030
Ceramic wastes in non-dispersible form:
Cermet wastes and scrap (metal ceramic composites)
Ceramic based fibres not elsewhere specified or included
B2040
Other wastes containing principally inorganic constituents:
Partially refined calcium sulphate produced from flue-gas desulphurization (FGD)
Waste gypsum wallboard or plasterboard arising from the demolition of buildings
Slag from copper production, chemically stabilized, having a high iron content (above 20 %) and processed according to industrial specifications (e.g. DIN 4301 and DIN 8201) mainly for construction and abrasive applications
Sulphur in solid form
Limestone from the production of calcium cyanamide (having a pH less than 9)
Sodium, potassium, calcium chlorides
Carborundum (silicon carbide)
Broken concrete
Lithium-tantalum and lithium-niobium containing glass scraps
B2050
Coal-fired power plant fly-ash, not included on list A (note the related entry on list A, A2060)
B2060
Spent activated carbon not containing any Annex I constituents to the extent that they exhibit Annex III characteristics, for example, carbon resulting from the treatment of potable water and processes of the food industry and vitamin production (note the related entry on list A, A4160)
B2070
Calcium fluoride sludge
B2080
Waste gypsum arising from chemical industry processes not included on list A (note the related entry on list A, A2040)
B2090
Waste anode butts from steel or aluminium production made of petroleum coke or bitumen and cleaned to normal industry specifications (excluding anode butts from chlor alkali electrolyses and from metallurgical industry)
B2100
Waste hydrates of aluminium and waste alumina and residues from alumina production excluding such materials used for gas cleaning, flocculation or filtration processes
B2110
Bauxite residue (‘red mud’) (pH moderated to less than 11,5)
B2120
Waste acidic or basic solutions with a pH greater than 2 and less than 11,5, which are not corrosive or otherwise hazardous (note the related entry on list A, A4090)
B2130
Bituminous material (asphalt waste) from road construction and maintenance, not containing tar [The concentration level of Benzo[a]pyrene should not be 50 mg/kg or more.] (note the related entry on list A, A3200)
B3
Wastes containing principally organic constituents, which may contain metals and inorganic materials
B3011 [For the purpose of this Regulation the terms ‘almost free from contamination and other types of waste’ and where relevant ‘almost exclusively consisting of’ shall be understood to mean that in a consignment of plastic waste or mixtures of plastic waste, classified under entry B3011, the content of contamination, other types of wastes or non-halogenated polymers, cured resins or condensation products, or fluorinated polymers, other than the one non-halogenated polymer, cured resin or condensation product, or fluorinated polymer that makes up the bulk of the plastic waste shall not exceed a total maximum of 2 % of the weight of the consignment.]
Plastic waste (note the related entry A3210, in list A of this Part, and entry Y48, in list A of Part 2)
Plastic waste listed below, provided it is destined for recycling [Recycling/reclamation of organic substances that are not used as solvents (R3 in Annex IV, Section B) or, if needed, temporary storage limited to one instance, provided that it is followed by operation R3 and evidenced by contractual or relevant official documentation.] in an environmentally sound manner and almost free from contamination and other types of wastes [In relation to ‘almost free from contamination and other types of wastes’, international and national specifications may offer a point of reference.]:
Plastic waste almost exclusively [In relation to ‘almost exclusively’, international and national specifications may offer a point of reference.] consisting of one non-halogenated polymer, including but not limited to the following polymers:
Polyethylene (PE)
Polypropylene (PP)
Polystyrene (PS)
Acrylonitrile butadiene styrene (ABS)
Polyethylene terephthalate (PET)
Polycarbonates (PC)
Polyethers
Plastic waste almost exclusively [In relation to ‘almost exclusively’, international and national specifications may offer a point of reference.] consisting of one cured resin or condensation product, including but not limited to the following resins:
Urea formaldehyde resins
Phenol formaldehyde resins
Melamine formaldehyde resins
Epoxy resins
Alkyd resins
Plastic waste almost exclusively [In relation to ‘almost exclusively’, international and national specifications may offer a point of reference.] consisting of one of the following fluorinated polymers [Post-consumer wastes are excluded.]:
Perfluoroethylene/propylene (FEP)
Perfluoroalkoxy alkanes: