Art. 1 Regulation (EU) 2024/1108

Amendments to Regulation (EU) No 748/2012

In force

Regulation (EU) No 748/2012 is amended as follows:

(1)

the title is replaced by the following:

‘Commission Regulation (EU) No 748/2012 of 3 August 2012 laying down implementing rules for the airworthiness and environmental certification or declaration of compliance of aircraft and related products, parts, appliances, control and monitoring units and control and monitoring unit components, as well as for the capability requirements of design and production organisations (recast)’;

(2)

Article 1 is amended as follows:

(a)

paragraph 1 is amended as follows:

(i)

the introductory sentence is replaced by the following:

‘This Regulation lays down, in accordance with Articles 19, 58 and 62 of Regulation (EU) 2018/1139, common technical requirements and administrative procedures for the airworthiness and environmental certification or declaration of compliance of products, parts, appliances, control and monitoring units and control and monitoring unit components specifying:

[Regulation (EU) 2018/1139 of the European Parliament and of the Council of 4 July 2018 on common rules in the field of civil aviation and establishing a European Union Aviation Safety Agency, and amending Regulations (EC) No 2111/2005, (EC) No 1008/2008, (EU) No 996/2010, (EU) No 376/2014 and Directives 2014/30/EU and 2014/53/EU of the European Parliament and of the Council, and repealing Regulations (EC) No 552/2004 and (EC) No 216/2008 of the European Parliament and of the Council and Council Regulation (EEC) No 3922/91 (OJ L 212, 22.8.2018, p. 1, ELI: http://data.europa.eu/eli/reg/2018/1139/oj)’;]

(ii)

points (f) and (g) are replaced by the following:

‘(f) the identification of products, parts, appliances, control and monitoring units and control and monitoring unit components;

(g)

the certification of certain parts, appliances and control and monitoring unit components;’;

(b)

paragraph 2 is amended as follows:

(i)

points (c) and (d) are replaced by the following:

‘(c) ‘Part 21’ means the requirements and procedures for the certification of aircraft and related products, parts, appliances, control and monitoring units and control and monitoring unit components, and of design and production organisations laid down in Annex I to this Regulation;

(d)

‘Part 21 Light’ means the requirements and procedures for the certification or declaration of design compliance of aircraft other than unmanned aircraft intended primarily for sports and recreational use and of related products and parts, and declaration of design and production capability of organisations laid down in Annex Ib (Part 21 Light) to this Regulation;’;

(ii)

point (f) is replaced by the following:

‘(f) ‘article’ means any part and appliance to be used on civil aircraft and any control and monitoring unit component;’;

(iii)

point (h) is replaced by the following:

‘(h) ‘EPA’ stands for European Part Approval. The European Part Approval of an article means that the article has been produced in accordance with approved design data not belonging to the type-certificate holder of the related product and control and monitoring unit, except for ETSO articles;’;

(iv)

the following points (l), (m), (n), (o) and (p) are added:

‘(l) ‘control and monitoring unit (CMU)’ means the equipment to control and monitor unmanned aircraft remotely, as defined in Article 3(32) of Regulation (EU) 2018/1139;

(m)

‘control and monitoring unit component’ means any element of the control and monitoring unit;

n)

‘control and monitoring unit installation’ means the process to integrate the control and monitoring unit components in a physical environment eligible for that purpose according to a set of installation and testing instructions, such that the installed control and monitoring unit can be used to operate an unmanned aircraft;

(o)

‘unmanned aircraft system (UAS)’ means an unmanned aircraft, as defined in Article 3(30) of Regulation (EU) 2018/1139, and its control and monitoring unit;

(p)

‘VTOL-capable aircraft’ (VCA) means a power-driven, heavier-than-air aircraft other than aeroplane or rotorcraft, capable of performing vertical take-off and landing by means of lift and thrust units used to provide lift during the take-off and landing.’;

(3)

Article 2 is amended as follows:

(1)

the heading is replaced by the following:

‘Certification of products, parts, appliances, control and monitoring unit and control and monitoring unit components’

(2)

paragraph 1 is replaced by the following:

‘1. Products, parts, appliances, control and monitoring units and control and monitoring unit components shall be issued with certificates as specified in Annex I (Part 21).’

;

(3)

in paragraph 2, the introductory sentence is replaced by the following:

‘By way of derogation from paragraph 1, certificates may be alternatively issued as specified in Annex I (b) (Part 21 Light) for the following products other than unmanned aircraft:’;

(4)

in paragraph 3, the introductory sentence is replaced by the following:

‘By way of derogation from paragraphs 1 and 2, a declaration of design compliance may alternatively be made, as specified in Annex Ib (Part 21 Light), for the following products other than unmanned aircraft:’;

(4)

Article 8 is amended as follows:

(1)

paragraph 1 is replaced by the following:

‘1. An organisation responsible for the design of products, parts, appliances, control and monitoring units and control and monitoring unit components, or for changes or repairs thereto, shall demonstrate its capability in accordance with Annex I (Part 21).’

;

(2)

in paragraph 5, the introductory sentence is replaced by the following:

‘By way of derogation from paragraph 1, an organisation whose principal place of business is in a non-Member State may demonstrate its capability by holding a certificate issued by that State for the product, part, appliance, control and monitoring unit and control and monitoring unit component for which it applies in accordance with Annex I (Part 21), provided:’;

(5)

Article 9 is amended as follows:

(1)

paragraphs 1 and 2 are replaced by the following:

‘1. An organisation responsible for the manufacture of products, parts, appliances, control and monitoring units and control and monitoring unit components shall demonstrate its capability in accordance with Annex I (Part 21). This demonstration of capability is not required for the parts, appliances or control and monitoring unit components that an organisation manufactures which, in accordance with Annex I (Part 21), are eligible for installation in a type-certified product without the need to be accompanied by an authorised release certificate (EASA Form 1).t

2.

By way of derogation from paragraph 1, a manufacturer whose principal place of business is in a non-Member State may demonstrate its capability by holding a certificate issued by that State for the product, part, appliance, control and monitoring unit and control and monitoring unit component for which it applies, provided that both of the following conditions are fulfilled:

(a)

that State is the State of manufacture;

(b)

the Agency has determined that the system of that State includes the same independent level of checking of compliance as provided for by this Regulation, either through an equivalent system of approvals of organisations or through direct involvement of the competent authority of that State.’

;

(2)

in paragraph 8, point (a) is replaced by the following:

‘(a) the manufacture of parts, appliances and control and monitoring unit components that are eligible, in accordance with Annex I (Part 21), for installation in a type-certified product without the need to be accompanied by an authorised release certificate (EASA Form 1);’;

(6)

Annex I (Part 21) is amended in accordance with Annex I to this Regulation.