ANNEX I, Regulation (EU) 2024/1108

In force

Annex I to Regulation (EU) No 748/2012 is amended as follows:

(1)

the title of Part 21 is replaced by the following:

‘Certification of aircraft and related products, parts, appliances, control and monitoring units and control and monitoring unit components, and of design and production organisations’;

(2)

the table of contents (‘Contents’) is amended as follows:

(a)

the title of point 21.A.2 is replaced by the following:

‘21.A.2 Undertaking by a person other than the applicant for, or holder of, a certificate’;

(b)

the title of point 21.A.35 is replaced by the following:

‘Flight tests’;

(c)

the title of point 21.A.115 is replaced by the following:

‘21.A.115 Requirements for the approval of major changes in the form of a supplemental type certificate’;

(d)

the title of point 21.A.128 is replaced by the following:

‘21.A.128 Tests: engines, propellers, and control and monitoring units (CMUs)’;

(e)

The title of Subpart K in Section A is replaced by the following:

‘SUBPART K — PARTS, APPLIANCES, AND CONTROL AND MONITORING UNIT (CMU) COMPONENTS’;

(f)

the title of point 21.A.303 is replaced by the following:

‘21.A.303 Compliance with the applicable requirements’;

(g)

the title of point 21.A.305 is replaced by the following:

‘21.A.305 Approval of parts, appliances, and control and monitoring unit (CMU) components’;

(h)

the following new title of point 21.A.308 is added:

‘21.A.308 Eligibility of a component for installation on a control and monitoring unit (CMU)’;

(i)

the title of Subpart Q in Section A is replaced by the following:

‘SUBPART Q — IDENTIFICATION OF PRODUCTS, PARTS, APPLIANCES, CONTROL AND MONITORING UNITS (CMUs) AND CMU COMPONENTS’;

(j)

the title of point 21.A.801 is replaced by the following:

‘21.A.801 Identification of products and control and monitoring units (CMUs)’;

(k)

the title of point 21.A.804 is replaced by the following:

‘21.A.804 Identification of parts, appliances and control and monitoring unit (CMU) components’;

(l)

the title of Subpart K in Section B is replaced by the following:

‘SUBPART K — PARTS, APPLIANCES AND CONTROL AND MONITORING UNIT (CMU) COMPONENTS’;

(m)

the title of Subpart Q in Section B is replaced by the following:

‘SUBPART Q — IDENTIFICATION OF PRODUCTS, PARTS, APPLIANCES, CONTROL AND MONITORING UNITS (CMUs) AND CMU COMPONENTS’;

(3)

point 21.A.2 is replaced by the following:

The actions and obligations required to be undertaken by the applicant for, or holder of, a certificate for a product, part, appliance, control and monitoring unit (CMU) or CMU component under this Section may be undertaken on their behalf by any other natural or legal person, provided the applicant for, or holder of, that certificate can show that they have made an agreement with the other person to ensure that the certificate holder’s obligations are and will be properly discharged.’;

(4)

point 21.A.3A is amended as follows:

(a)

point (a) is replaced by the following:

‘(a) Without prejudice to Regulation (EU) No 376/2014 of the European Parliament and of the Council and its delegated and implementing acts, all natural or legal persons that have applied for or hold a type-certificate, restricted type-certificate, supplemental type-certificate, European Technical Standard Order (ETSO) authorisation, major repair design approval or any other relevant approval deemed to have been issued under this Regulation shall:

1.

establish and maintain a system for collecting, investigating and analysing occurrence reports in order to identify adverse trends or to address deficiencies and to extract occurrences whose reporting is mandatory in accordance with point 3 and those which are reported voluntarily. When the principal place of business is located in a Member State, a single system may be established to meet the requirements of Regulation (EU) No 376/2014 of the European Parliament and of the Council and its implementing acts and of Regulation (EU) 2018/1139 and its delegated and implementing acts. The reporting system shall include:

(i)

reports of and information related to failures, malfunctions, defects or other occurrences which cause or might cause adverse effects on the continuing airworthiness of the product, part, appliance, UAS, CMU or CMU component covered by the type-certificate, restricted type-certificate, supplemental type-certificate, ETSO authorisation, major repair design approval or by any other relevant approval deemed to have been issued under this Regulation;

(ii)

errors, near misses and hazards that do not fall under point (i);

2.

make available to known operators of the product, part, appliance, UAS, CMU or CMU component and, on request, to any person authorised under other implementing or delegated acts the information about the system established in accordance with point 1, and on how to provide reports of and information related to failures, malfunctions, defects or other occurrences referred to in point l(i);

3.

report to the Agency any failure, malfunction, defect or other occurrence of which it is aware and is related to a product, part, appliance, UAS, CMU or CMU component covered by the type-certificate, restricted type-certificate, supplemental type-certificate, ETSO authorisation, major repair design approval or by any other relevant approval deemed to have been issued under this Regulation, and which has resulted or may result in an unsafe condition.

[Regulation (EU) No 376/2014 of the European Parliament and of the Council of 3 April 2014 on the reporting, analysis and follow-up of occurrences in civil aviation, amending Regulation (EU) No 996/2010 of the European Parliament and of the Council and repealing Directive 2003/42/EC of the European Parliament and of the Council and Commission Regulations (EC) No 1321/2007 and (EC) No 1330/2007 (OJ L 122, 24.4.2014, p. 18).’;]

(b)

point (b) is replaced by the following:

‘(b) Without prejudice to Regulation (EU) No 376/2014 and its delegated and implementing acts, any natural or legal person that holds or has applied for a production organisation approval certificate under Subpart G of this Section, or that produces a product, part, appliance, UAS, CMU or CMU component under Subpart F of this Section, shall:

1.

establish and maintain a system for collecting and assessing occurrence reports, including reports on errors, near misses and hazards, in order to identify adverse trends or to address deficiencies and extract occurrences whose reporting is mandatory in accordance with points 2 and 3 of this point and those which are reported voluntarily. For organisations that have their principal place of business in a Member State, a single system may be established to meet the requirements of Regulation (EU) No 376/2014 and its implementing acts and of Regulation (EU) 2018/1139 and its delegated and implementing acts;

2.

report to the responsible design approval holder all the cases where products, parts, appliances, UAS, CMUs or CMU components have been released by the production organisation and possible deviations from the applicable design data have been subsequently identified, and investigate with the design approval holder to identify those deviations which could lead to an unsafe condition;

3.

report to the competent authority of the Member State responsible in accordance with point 21.1 and the Agency the deviations that have been identified in accordance with point 21.A.3A(b)2 and which could lead to an unsafe condition;

4.

if the production organisation acts as a supplier to another production organisation, also report to that other organisation all the cases where it has released products, parts, appliances, UAS, CMUs or CMU components to that organisation and the possible deviations from the applicable design data that have been subsequently identified.’;

(5)

point 21.A.3B is replaced by the following:

(a)

An airworthiness directive means a document issued or adopted by the Agency which mandates actions to be performed on an aircraft or on a CMU to restore an acceptable level of safety, when evidence shows that the safety level of the aircraft, UAS or CMU may otherwise be compromised.

(b)

The Agency shall issue an airworthiness directive when:

1.

an unsafe condition has been determined by the Agency to exist in an aircraft, a UAS or a CMU, as a result of a deficiency in the aircraft, or an engine, propeller, part or appliance installed on this aircraft, or as a result of a deficiency in the CMU or the CMU component; and

2.

that condition is likely to exist or develop in other aircraft, UAS or CMUs.

(c)

When an airworthiness directive has to be issued by the Agency to correct the unsafe condition referred to in point (b), or to require the performance of an inspection, the holder of the type-certificate, restricted type-certificate, supplemental type-certificate, major repair design approval, ETSO authorisation or any other relevant approval deemed to have been issued under this Regulation, shall:

1.

propose the appropriate corrective action or required inspections, or both, and submit details of these proposals to the Agency for approval; and

2.

following the approval by the Agency of the proposals referred to in point 1, make available to all known operators or owners of the product, part, appliance, UAS, CMU or CMU component and, on request, to any person required to comply with the airworthiness directive, appropriate descriptive data and accomplishment instructions.

(d)

An airworthiness directive shall contain at least the following information:

1.

an identification of the unsafe condition;

2.

an identification of the affected aircraft or CMU;

3.

the action(s) required;

4.

the compliance time for the required action(s);

5.

the date of entry into force of the airworthiness directive.’;

(6)

in point 21.A.4, point (b) is replaced by the following:

‘(b) the proper support of the continued airworthiness of the product, part, appliance, UAS, CMU or CMU component.’;

(7)

in point 21.A.5, points (a), (b) and (c) are replaced by the following:

‘(a) when they design a product, part, appliance, UAS, CMU or CMU component, or changes or repairs thereto, establish a record-keeping system and maintain the relevant design information/data; that information/data shall be made available to the Agency in order to provide the information/data that is necessary to ensure the continued airworthiness of the product, part, appliance, UAS, CMU or CMU component, the continued validity of the operational suitability data, and compliance with the applicable environmental protection requirements;

(b)

when they produce a product, part, appliance, CMU or CMU component, record the details of the production process relevant to the conformity of the product, part, appliance, CMU or CMU component with the applicable design data, and the requirements imposed on their partners and suppliers, and make that data available to their competent authority in order to provide the information that is necessary to ensure the continuing airworthiness of the product, part, appliance, UAS, CMU or CMU component;

(c)

with regard to permits to fly:

1.

maintain the documents that are produced to establish and justify the flight conditions, and make them available to the Agency and to their competent authority of the Member State in order to provide the information that is necessary to ensure the continued airworthiness of the aircraft, the UAS and the CMU;

2.

when they issue a permit to fly under the privilege of approved organisations, maintain the documents associated with it, including inspection records and documents that support the approval of the flight conditions and the issuance of the permit to fly itself, and make them available to the Agency and to their competent authority of the Member State responsible for the oversight of the organisation in order to provide the information that is necessary to ensure the continued airworthiness of the aircraft, the UAS and the CMU;’;

(8)

point 21.A.6 is replaced by the following:

The holder of a type-certificate, restricted type-certificate, or supplemental type-certificate shall:

‘(a) produce, maintain and update master copies of all manuals or variations in the manuals required by the applicable type-certification basis, the applicable operational suitability data certification basis and the applicable environmental protection requirements for the product, UAS, CMU or article, and provide copies, on request, to the Agency;

(b)

for unmanned aircraft, determine whether the installation of a CMU in a physical environment is necessary, and provide the operator with all the necessary instructions for the installation of the CMU and for its installation to be released in accordance with Annex I (Part-ML.UAS) to Commission Delegated Regulation (EU) 2024/1107’;

(9)

points 21.A.7 is replaced by the following:

‘(a) The holder of a type-certificate, restricted type-certificate, supplemental type-certificate, design change or repair design approval shall develop or reference the instructions which are necessary for ensuring that the airworthiness standard related to the aircraft, the UAS and the CMU type and any associated part or CMU component is maintained throughout the operational life of the aircraft or the UAS, when demonstrating compliance with the applicable type-certification basis established and notified by the Agency in accordance with point 21.B.80.

(b)

At least one set of complete instructions for continued airworthiness shall be provided by the holder of:

1.

a type-certificate or restricted type-certificate to each known owner of one or more products, UAS or CMUs upon their delivery or upon the issuance of the first certificate of airworthiness or restricted certificate of airworthiness for the affected aircraft, whichever occurs later;

2.

a supplemental type-certificate or design change approval to all known operators of the product, the UAS or the CMU affected by the change upon the release to service of the modified product or modified CMU;

3.

a repair design approval to all known operators of the product or the CMU affected by the repair upon the release to service of the product or the CMU in which the repair design is embodied; the repaired product, part, appliance, CMU or CMU component may be released into service before the related instructions for continued airworthiness have been completed, but this shall be for a limited service period, and in agreement with the Agency.

Thereafter, those design approval holders shall make those instructions available on request to any other person required to comply with those instructions.

(c)

By way of derogation from point (b), the type-certificate holder or restricted type-certificate holder may delay the availability of a part of the instructions for continued airworthiness, dealing with long lead accomplishment instructions of a scheduled nature, until after the product or the CMU, or modified product or modified CMU, has entered into service, but shall make those instructions available before the use of this data is required for the product or modified product.

(d)

The design approval holder that is required to provide instructions for continued airworthiness in accordance with point (b) shall also make available the changes to those instructions to all known operators of the product, the UAS or the CMU affected by the change and, on request, to any other person required to comply with those changes. That design approval holder shall demonstrate to the Agency, on request, the adequacy of the process of making changes to the instructions for continued airworthiness available in accordance with this point.’;

(10)

in point 21.A.9, point (a) is replaced by the following:

‘(a) grant the competent authority access to any facility, product, part, appliance, CMU, CMU component, document, record, data, process, procedure or to any other material in order to review any report, make any inspection, or perform or witness any flight and ground test, as necessary, in order to verify the initial and continued compliance of the organisation with the applicable requirements of Regulation (EU) 2018/1139 and its delegated and implementing acts;’;

(11)

point 21.A.11 is replaced by the following:

This Subpart establishes the procedure for issuing type-certificates for products and CMUs and restricted type-certificates for aircraft, and establishes the rights and obligations of the applicants for, and holders of, those certificates.’;

(12)

point 21.A.15, is amended as follows:

(a)

point (b) is replaced by the following:

‘(b) An application for a type-certificate or restricted type-certificate shall include, as a minimum, preliminary descriptive data of the product, the UAS or the CMU, and the kind of operations for which certification is requested. In addition, it shall include, or be supplemented after the initial application by, a certification programme for the demonstration of compliance in accordance with point 21.A.20, consisting of all of the following:

1.

a detailed description of the type design, including all the configurations to be certified;

2.

the proposed operating characteristics and limitations;

3.

the intended use of the product, the UAS or the CMU, and the kind of operations for which certification is requested;

4.

a proposal for the initial type-certification basis, operational suitability data certification basis and environmental protection requirements, prepared in accordance with the requirements and options specified in points 21.B.80, 21.B.82 and 21.B.85;

5.

a proposal for a breakdown of the certification programme into meaningful groups of compliance demonstration activities and data, including a proposal for the means of compliance and related compliance documents;

6.

a proposal for the assessment of the meaningful groups of compliance demonstration activities and data, addressing the likelihood of an unidentified non-compliance with the type-certification basis, operational suitability data certification basis or environmental protection requirements and the potential impact of that non-compliance on product and UAS safety or environmental protection or on the safety of the CMU. The proposed assessment shall take into account at least the elements set out in points (1) to (4) of point 21.B.100(a). Based on that assessment, the application shall include a proposal for the Agency’s involvement in the verification of the compliance demonstration activities and data;

7.

a project schedule including major milestones.’;

(b)

point (e) is replaced by the following:

‘(e) An application for a type-certificate or restricted type-certificate for a large aeroplane or a large rotorcraft shall be valid for 5 years and an application for any other type-certificate or restricted type-certificate shall be valid for 3 years, unless the applicant demonstrates at the time of application that its product, UAS or CMU requires a longer period of time to demonstrate and declare compliance and the Agency agrees to that longer period of time.’;

(13)

point 21.A.19 is replaced by the following:

Any natural or legal person proposing a change to a product shall apply for a new type-certificate if the Agency finds that the change in the design, power, thrust, or mass is so extensive that a substantially complete investigation of compliance with the applicable type-certification basis is required.

Any natural or legal person proposing a change to a UAS or a CMU shall apply for a new type-certificate if the Agency finds that the change in the design is so extensive that a substantially complete investigation of compliance with the applicable type-certification basis is required.’;

(14)

in point 21.A.20(d), point 2 is replaced by the following:

‘2. no feature or characteristic has been identified that may make the product, the UAS or the CMU unsafe for the uses for which certification is requested.’;

(15)

point 21.A.21 is replaced by the following:

(a)

In order to be issued with a product or a CMU type certificate, or with an aircraft restricted type certificate for the aircraft that does not meet the essential requirements laid down in Annex II to Regulation (EU) 2018/1139,, the applicant shall:

1.

demonstrate its capability in accordance with point 21.A.14;

2.

demonstrate compliance in accordance with point 21.A.20;

3.

for an aircraft type certificate or restricted type certificate, demonstrate that the engine or propeller, or both, if installed on the aircraft:

(i)

has/have a type certificate issued or determined in accordance with this Regulation; or

(ii)

is/are compliant with the aircraft type-certification basis established for aircraft other than unmanned aircraft, or with the UAS type-certification basis for unmanned aircraft, and the environmental protection requirements designated and notified by the Agency as necessary to ensure the safe flight of the aircraft;

4.

for an unmanned aircraft type certificate or restricted type certificate:

(i)

demonstrate compliance with the UAS type-certification basis in accordance with point 21.B.80;

(ii)

demonstrate that the CMU has a type certificate issued in accordance with this Regulation, if the CMU has been certified separately from the unmanned aircraft.

(b)

By way of derogation from point (a)(2), at the applicant’s request included in the declaration referred to in point 21.A.20(d), the applicant is entitled to have the aircraft type certificate or restricted type certificate issued before the applicant has demonstrated compliance with the applicable operational suitability data certification basis, provided that the applicant demonstrates such compliance before the date on which this data is to be actually used.’;

(16)

point 21.A.31 is replaced by the following:

(a)

The type design shall consist of:

1.

the drawings and specifications, and a listing of those drawings and specifications, necessary to define the configuration and the design features of the product, the UAS or the CMU shown to comply with the applicable type-certification basis and environmental protection requirements;

2.

information on the materials and processes and on the methods of manufacture and assembly of the product and the CMU necessary to ensure the conformity of the product and the CMU;

3.

an approved airworthiness limitations section of the instructions for continued airworthiness as defined by the applicable certification specifications; and

4.

any other data that allows by comparison the determination of the airworthiness and, if relevant, the environmental characteristics of later products andCMUs of the same type.

(b)

Each type design shall be adequately identified.’;

(17)

in point 21.A.33(b)(1), point (ii) is replaced by the following:

‘(ii) the parts of the products and the CMU components adequately conform to the drawings in the proposed type design; and’;

This article is long: the rest is at the official publication.