The following information, if applicable, is the minimum data required for the road load determination test.
APPLICANT | | |
Manufacturer | | |
SUBJECT | Determination of a vehicle road load /…
Roadload family identifier(s) | : |
Object submitted to tests
Make | : |
Type | : |
CONCLUSION | The object submitted to tests complies with the requirements mentioned in the subject.
PLACE, | DD/MM/YYYY
Make(s) concerned | : |
Type(s) concerned | : |
Commercial description | : |
Maximal speed (km/h) | : |
Powered axle(s) | : |
If no interpolation: the worst-case vehicle (regarding energy demand) shall be described
Combination with | : | Flat belt dynamometer / chassis dynamometer
Wind tunnel | Dynamometer
HR | LR | HR | LR
Make | | | |
Type | | | |
Version | | | |
Cycle energy demand over a complete WLTC Class 3 cycle (kJ) | | | |
Deviation from production series | — | — | |
Mileage (km) | — | — | |
Or (in case of roadload matrix family):
Make | : |
Type | : |
Version | : |
Cycle energy demand over a complete WLTC (kJ) | : |
Deviation from production series | : |
Mileage (km) | : |
Dynamometer
HR | LR
Test mass (kg) | |
Average mass mav (kg) | |
Value of mr (kg per axle) | |
Category M vehicle:
proportion of the vehicle mass in running order on the front axle (%)
Category N vehicle:
weight distribution (kg or %)
Or (in case of roadload matrix family):
Test mass (kg) | : |
Average mass mav(kg) | : | (average before and after the test)
Technically permissible maximum laden mass | : |
Estimated arithmetic average of the mass of optional equipment | : |
Category M vehicle:
proportion of the vehicle mass in running order on the front axle (%)
: |
Category N vehicle:
weight distribution (kg or %)
: |
Wind tunnel | Dynamometer
HR | LR | HR | LR
Size designation | | | |
Make | | | |
Type | | | |
Rolling resistance
Front (kg/t) | — | — | |
Rear (kg/t) | — | — | |
Tyre pressure
Front (kPa) | — | — | |
Rear (kPa) | — | — | |
Or (in case of roadload matrix family):
Size designation
Make | : |
Type | : |
Rolling resistance
Front (kg/t) | : |
Rear (kg/t) | : |
Tyre pressure
Front (kPa) | : |
Rear (kPa) | : |
Wind tunnel
HR | LR
Type | AA/AB/AC/AD/AE/AF BA/BB/BC/BD |
Version | |
Aerodynamic devices
Movable aerodynamic body parts | y/n and list if applicable |
Installed aerodynamic options list | |
Delta (CD × Af)LH compared to HR (m2) | — |
Or (in case of roadload matrix family):
Body shape description | : | Square box (if no representative body shape for a complete vehicle can be determined)
Frontal area Afr (m2) | : |
HR | LR
Make | |
Type | |
Version | |
Cycle energy demand over a complete WLTC Class 3 cycle (kJ) | |
Deviation from production series | |
Mileage | |
Or (in case of roadload matrix family):
Make | : |
Type | : |
Version | : |
Cycle energy demand over a complete WLTC (kJ) | : |
Deviation from production series | : |
Mileage (km) | : |
HR | LR
Test mass (kg) | |
Average mass mav (kg) | |
Value of mr (kg per axle) | |
Category M vehicle:
proportion of the vehicle mass in running order on the front axle (%)
Category N vehicle:
weight distribution (kg or %)
Or (in case of roadload matrix family):
Test mass (kg) | : |
Average mass mav (kg) | : | (average before and after the test)
Technically permissible maximum laden mass | : |
Estimated arithmetic average of the mass of optional equipment | : |
Category M vehicle:
proportion of the vehicle mass in running order on the front axle (%)
Category N vehicle:
weight distribution (kg or %)
HR | LR
Size designation | |
Make | |
Type | |
Rolling resistance
Front (kg/t) | |
Rear (kg/t) | |
Tyre pressure
Front (kPa) | |
Rear (kPa) | |
Or (in case of roadload matrix family):
Size designation | : |
Make | : |
Type | : |
Rolling resistance
Front (kg/t) | : |
Rear (kg/t) | : |
Tyre pressure
Front (kPa) | : |
Rear (kPa) | : |
HR | LR
Type | AA/AB/AC/AD/AE/AF BA/BB/BC/BD |
Version | |
Aerodynamic devices
Movable aerodynamic body parts | y/n and list if applicable |
Installed aerodynamic options list | |
Delta (CD × Af)LH compared to HR (m2) | — |
Or (in case of roadload matrix family):
Body shape description | : | Square box (if no representative body shape for a complete vehicle can be determined)
Frontal area Afr (m2) | : |
Engine code | : |
Transmission type | : | manual, automatic, CVT
Transmission model
(manufacturer's codes)
: | (torque rating and no of clutches → to be included in info doc)
Covered transmission models
(manufacturer's codes)
: | | |
Engine rotational speed divided by vehicle speed | : | Gear | Gear ratio | N/V ratio
1st | 1/.. |
2nd | 1/.. |
3rd | 1/.. |
4th | 1/.. |
5th | 1/.. |
6th | 1/.. |
.. | |
.. | |
Electric machine(s) coupled in position N | : | n.a. (no electric machine or no coastdown mode)
Type and number of electric machines | : | construction type: asynchronous/ synchronous…
Type of coolant | : | air, liquid, …
Repeat §2.3.1. with VL data
Dates of tests | : |
dd/mm/yyyy (wind tunnel)
dd/mm/yyyy (dynamometer)
or
dd/mm/yyyy (on road)
[As defined in point 4.2. of Appendix 1 of Annex I to Regulation (EU) 2018/858.] [The dimension defined in point 6.3 of Standard ISO 612:1978.]
Method of the test | : |
coastdown
or torque meter method
Facility (name / location / track's reference) | : |
Coastdown mode | : | y/n
Wheel alignment | : | Toe and camber values
Ground clearance | : |
Vehicle height | : |
Drivetrain lubricants | : |
Wheel bearing lubricants | : |
Brake adjustment to avoid unrepresentative parasitic drag | : |
Maximum reference speed (km/h) | : |
Anemometry | : |
stationary
or on board: influence of anemometry (CD × A) and if it was corrected.
Number of split(s) | : |
Wind | : | average, peaks and direction in conjunction with direction of the test track
Air pressure | : |
Temperature (mean value) | : |
Wind correction | : | y/n
Tyre pressure adjustment | : | y/n
Raw results | : |
Torque method:
c0 =
c1 =
c2 =
Coastdown method:
f0
f1
f2
Final results | |
Torque method:
c0 =
c1 =
c2 =
and
f0 =
f1 =
f2 =
Coastdown method:
f0 =
f1 =
f2 =
Or
Facility (name/location/dynamometer's reference) | : | |
Qualification of the facilities | : | Report reference and date
Dynamometer
Type of dynamometer | : | flat belt or chassis dynamometer
Method | : | stabilised speeds or deceleration method
Warm up | : | warm-up by dyno or by driving the vehicle
Correction of the roller curve | : | (for chassis dynamometer, if applicable)
Method of chassis dynamometer setting | : | Fixed run / iterative / alternative with its own warmup cycle
Measured aerodynamic drag coefficient multiplied by the frontal area | : | Velocity (km/h) | CD × A (m2)
… | …
… | …
Result | : |
f0 =
f1 =
f2 =
Or
[As defined in point 4.2. of Appendix 1 of Annex I to Regulation (EU) 2018/858.] [The dimension defined in point 6.3 of Standard ISO 612:1978.]
Method of the test | : |
coastdown
or torque meter method
Facility (name/location/track's reference) | : |
Coastdown mode | : | y/n
Wheel alignment | : | Toe and camber values
Ground clearance | : |
Vehicle height | : |
Drivetrain lubricants | : |
Wheel bearing lubricants | : |
Brake adjustment to avoid unrepresentative parasitic drag | : |
Maximum reference speed (km/h) | : |
Anemometry | : |
stationary
or on board: influence of anemometry (CD × A) and if it was corrected.
Number of split(s) | : |
Wind | : | average, peaks and direction in conjunction with direction of the test track
Air pressure | : |
Temperature (mean value) | : |
Wind correction | : | y/n
Tyre pressure adjustment | : | y/n
Raw results | : |
Torque method:
c0r =
c1r =
c2r =
Coastdown method:
f0r =
f1r =
f2r =
Final results | |
Torque method:
c0r =
c1r =
c2r =
and
f0r (calculated for vehicle HM) =
f2r (calculated for vehicle HM) =
f0r (calculated for vehicle LM) =
f2r (calculated for vehicle LM) =
Coastdown method:
f0r (calculated for vehicle HM) =
f2r (calculated for vehicle HM) =
f0r (calculated for vehicle LM) =
f2r (calculated for vehicle LM) =
Or
Facility (name/location/dynamometer's reference) | : | |
Qualification of the facilities | : | Report reference and date
Dynamometer
Type of dynamometer | : | flat belt or chassis dynamometer
Method | : | stabilised speeds or deceleration method
Warm up | : | warm-up by dyno or by driving the vehicle
Correction of the roller curve | : | (for chassis dynamometer, if applicable)
Method of chassis dynamometer setting | : | Fixed run / iterative / alternative with its own warmup cycle
Measured aerodynamic drag coefficient multiplied by the frontal area | : | Velocity (km/h) | CD × A (m2)
… | …
… | …
Result | : |
f0r =
f1r =
f2r =
f0r (calculated for vehicle HM) =
f2r (calculated for vehicle HM) =
f0r (calculated for vehicle LM) =
f2r (calculated for vehicle LM) =
Repeat §2.4.1. with VL data’