Regulation (EU) 2017/2400 is amended as follows:
Articles 1 and 2 are replaced by the following:
This Regulation complements the legal framework for the type-approval of motor vehicles and engines with regard to emissions established by Regulation (EU) No 582/2011 by laying down the rules for issuing licences to operate a simulation tool with a view to determining CO2 emissions and fuel consumption of new vehicles to be sold, registered or put into service in the Union and for operating that simulation tool and declaring the CO2 emissions and fuel consumption values thus determined.
Subject to Article 4, second paragraph, this Regulation shall apply to medium lorries, heavy lorries and heavy buses.
In the case of multi-stage type-approvals or individual approvals of medium and heavy lorries, this Regulation shall apply to base lorries.
In the case of heavy buses, this Regulation shall apply to primary vehicles, interim vehicles and to complete vehicles or completed vehicles.
This Regulation shall not apply to off-road vehicles, special purpose vehicles and off-road special purpose vehicles as defined, respectively, in Part A, points 2.1., 2.2. and 2.3., of Annex I to Regulation (EU) 2018/858 of the European Parliament and of the Council [Regulation (EU) 2018/858 of the European Parliament and of the Council of 30 May 2018 on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles, amending Regulations (EC) No 715/2007 and (EC) No 595/2009 and repealing Directive 2007/46/EC (OJ L 151, 14.6.2018, p. 1).’;].
Article 3 is amended as follows:
the first paragraph is amended as follows:
points 10, 11 and 12 are replaced by the following:
‘(10) “axle” means a component comprising all rotating parts of the driveline which transfer the driving torque coming from the prop shaft to the wheels and changes the torque and speed with a fixed ratio and including the functions of a differential gear;
“air drag” means characteristic of a vehicle configuration regarding aerodynamic force acting on the vehicle in the direction of air flow and determined as a product of the drag coefficient and the cross sectional area for zero crosswind conditions;
“auxiliaries” means vehicle components including an engine fan, steering system, electric system, pneumatic system and Heating, Ventilation and Air Conditioning (HVAC) system whose CO2 emissions and fuel consumption properties have been defined in Annex IX;’;
points 15 to 18 are replaced by the following:
‘(15) “zero emission heavy-duty vehicle” (Ze-HDV) means “zero emission heavy-duty vehicle” as defined in Article 3, point (11), of Regulation (EU) 2019/1242 of the European Parliament and of the Council;
“vocational vehicle” means a heavy-duty vehicle not intended for the delivery of goods and for which one of the following digits is used to supplement the bodywork codes, as listed in Appendix 2 to Annex I to Regulation (EU) 2018/858: 09, 10, 15, 16, 18, 19, 20, 23, 24, 25, 26, 27, 28, 31; or a tractor with a maximum speed not exceeding 79 km/h;
“rigid lorry” means a “lorry” as defined in Part C, point 4.1, of Annex I to Regulation (EU) 2018/858, except for the lorries designed or constructed for the towing of a semi-trailer;
“tractor” means a “tractor unit for semi-trailer” as defined in Part C, point 4.3, of Annex I to Regulation (EU) 2018/858’
paragraph 20 is replaced by the following:
‘(20) “hybrid electric heavy-duty vehicle” (He-HDV) means a hybrid heavy duty vehicle that, for the purpose of mechanical propulsion, draws energy from both of the following on-vehicle sources of stored energy or power: (i) a consumable fuel, and (ii) an electrical energy or power storage device;’;
the following points (22) to (39) are added:
‘(22) “primary vehicle” means a heavy bus in a virtual assembly condition determined for simulation purposes, for which the input data and input information as set out in Annex III is used;
“manufacturer’s records file” means a file produced by the simulation tool which contains manufacturer related information, a documentation of the input data and input information to the simulation tool and the results for CO2 emissions and fuel consumption;
“customer information file” means a file produced by the simulation tool which contains a defined set of vehicle related information and the results for CO2 emissions and fuel consumption as defined in Part II of Annex IV;
“vehicle information file” (VIF) means a file produced by the simulation tool for heavy buses to transfer the relevant input data, input information and simulation results to subsequent manufacturing stages following the method as described in point (2) of Annex I;
“medium lorry” means a vehicle of category N2, as defined in Article 4(1), point (b)(ii), of Regulation (EU) 2018/858, with a technically permissible maximum laden mass exceeding 5000 kg and not exceeding 7400 kg;
“heavy lorry” means a vehicle of category N2, as defined in Article 4(1), point (b)(ii), of Regulation (EU) 2018/858, with a technically permissible maximum laden mass exceeding 7400 kg and a vehicle of category N3, as defined in Article 4(1), point (b)(iii), of that Regulation;
“heavy bus” means a vehicle of category M3, as defined in Article 4(1), point (a)(iii), of Regulation (EU) 2018/858, with a technically permissible maximum laden mass of more than 7500 kg;
“primary vehicle manufacturer” means a manufacturer responsible for the primary vehicle;
“interim vehicle” means any further completion of a primary vehicle where a sub-set of input data and input information as defined for the complete or completed vehicle in accordance with Table 1 and Table 3a of Annex III is added and/or modified;
“interim manufacturer” means a manufacturer responsible for an interim vehicle;
“incomplete vehicle” means “incomplete vehicle” as defined in Article 3, point (25), of Regulation (EU) 2018/858;
“completed vehicle” means “completed vehicle” as defined in Article 3, point (26), of Regulation (EU) 2018/858;
“complete vehicle” means “complete vehicle” as defined in Article 3, point (27), of Regulation (EU) 2018/858;
“standard value” is input data for the simulation tool for a component where certification of input data is applicable, but the component has not been tested to determine a specific value and which reflects the worst-case performance of a component;
“generic value” is data used in the simulation tool for components or vehicle parameters where no component testing or declaration of specific values is foreseen and which reflects performance of average component technology or typical vehicle specifications;
“van” means a “van” as defined in Part C, point 4.2, of Annex I to Regulation (EU) 2018/858;
“application case” means the different scenarios to be followed in the case of a medium lorry, heavy lorry, heavy bus that is a primary vehicle, heavy bus that is an interim vehicle, heavy bus that is a complete vehicle or completed vehicle for which different manufacturer provisions and functions are applicable in the simulation tool;
“base lorry” means a medium lorry or heavy lorry equipped at least with:
a chassis, engine, transmission, axles and tyres, in the case of pure internal combustion engine vehicles;
a chassis, electric machine system and/or integrated electric powertrain component, battery system(s) and/or capacitor system(s) and tyres, in the case of pure electric vehicles;
a chassis, engine, electric machine system and/or integrated electric powertrain component and/or integrated hybrid electric vehicle powertrain component type 1, battery system(s) and/or capacitor system(s) and tyres, in the case of hybrid electric heavy-duty vehicles.’;
the second paragraph is deleted;
Article 4 is replaced by the following:
For the purpose of this Regulation, motor vehicles shall be classified in vehicle groups in accordance with Annex I, Tables 1 to 6.
Articles 5 to 23 do not apply to heavy lorries of vehicle groups 6, 7, 8, 13, 14, 15, 17, 18 and 19 as set out in Table 1 of Annex I, and to medium lorries of vehicle groups 51, 52, 55 and 56, as set out in Table 2 of Annex I and to any vehicle with a driven front axle in the vehicle groups 11, 12 and 16 as set out in Table 1 of Annex I.’;
in Article 5(3), the first sentence is replaced by the following:
‘The simulation tool shall be used for the purposes of determining CO2 emissions and fuel consumption of new vehicles.’;
in Article 5, paragraph 5 is replaced by the following:
‘5. The hashing tools shall be used for establishing an unequivocal association between the certified CO2 emission and fuel consumption related properties of a component, separate technical unit or system and its certification document, as well as for establishing an unequivocal association between a vehicle and its manufacturer’s records file, vehicle information file and customer information file as referred to in Annex IV.’;
in Chapter 2, the title is replaced by the following:
‘LICENCE TO OPERATE THE SIMULATION TOOL FOR THE PURPOSES OF TYPE-APPROVAL WITH REGARD TO EMISSIONS’;
Article 6 is amended as follows:
paragraph 1 is replaced by the following:
‘1. The vehicle manufacturer shall submit to the approval authority an application for a licence to operate the simulation tool for an application case with a view to determining CO2 emissions and fuel consumption of new vehicles belonging to one or more vehicle groups (“licence”). An individual licence shall apply to only a single such application case.
The application for a licence shall be accompanied by an adequate description of the processes set up by the vehicle manufacturer with a view to the operation of the simulation tool with respect to the application case concerned, as set out in point (1) of Annex II.’;
paragraph 4 is replaced by the following:
‘4. The vehicle manufacturer shall submit the application for a licence to the approval authority at the latest together with the application for an EC type-approval of a vehicle with an approved engine system with regard to emissions pursuant to Article 7 of Regulation (EU) No 582/2011, with the application for an EC type-approval of a vehicle with regard to emissions pursuant to Article 9 of that Regulation, with an application for a whole-vehicle type-approval pursuant to Regulation (EU) 2018/858 or the application for a national individual vehicle approval. The approval of a pure electric engine system and the EC type-approval of a pure electric vehicle with regard to emissions referred to in the previous sentence is limited to the measurement of net engine power in accordance with Annex XIV to Regulation (EU) No 582/2011.
The application for a licence must concern the application case which includes the type of vehicle concerned by the application for EU type-approval.’;
Article 7(1) is replaced by the following:
‘1. The approval authority shall grant the licence if the vehicle manufacturer submits an application in accordance with Article 6 and proves that the requirements laid down in Annex II are met with respect to the application case concerned.’;
Article 8 is amended as follows:
paragraph 1 is deleted;
paragraph 3 is replaced by the following:
‘3. After obtaining the licence, the vehicle manufacturer shall notify the approval authority without delay of any changes to the processes set up by it for the purposes of the licence for the application case covered by the licence that may affect the accuracy, reliability and stability of those processes.’;
Article 9 is amended as follows:
paragraph 1 is replaced by the following:
‘1. A vehicle manufacturer shall determine the CO2 emissions and fuel consumption of each new vehicle, with the exception of new vehicles using vehicle technologies listed in Appendix 1 to Annex III, to be sold, registered or put into service in the Union using the latest available version of the simulation tool referred to in Article 5(3). With regard to heavy buses the vehicle manufacturer or interim manufacturer shall use the method set out in Annex I, point (2).
For vehicle technologies listed in Appendix 1 to Annex III to be sold, registered or put into service in the Union, the vehicle manufacturer or interim manufacturer shall determine only the input parameters specified for those vehicles in the models set out in Table 5 of Annex III, using the latest available version of the simulation tool referred to in Article 5(3).
A vehicle manufacturer may operate the simulation tool for the purposes of this Article only if in possession of a licence granted for the application case concerned in accordance with Article 7. An interim manufacturer operates the simulation tool under the licence of a vehicle manufacturer.’;
in paragraph 2, the following subparagraph is added:
‘Vehicle manufacturers of heavy buses additionally shall record the results of the simulation in the vehicle information file. Interim manufacturers of heavy buses shall record the vehicle information file.’;
paragraph 3 is replaced by the following:
‘3. The vehicle manufacturer of medium lorries and heavy lorries shall create cryptographic hashes of the manufacturer’s records file and of the customer information file.
The primary vehicle manufacturer shall create cryptographic hashes of the manufacturer’s records file and of the vehicle information file.
The interim manufacturer shall create the cryptographic hash of the vehicle information file.
The vehicle manufacturer of complete vehicles or completed vehicles that are heavy buses, shall create cryptographic hashes of the manufacturer’s records file, of the customer information file and of the vehicle information file.’;
paragraph 4 is amended as follows:
the first subparagraph is replaced by the following:
‘Lorries and complete vehicles or completed vehicles that are heavy buses to be registered, sold or to enter into service shall be accompanied by the customer information file drawn up by the manufacturer in accordance with the model set out in Part II of Annex IV.’;
the following subparagraph is added:
‘Vehicle manufacturers of heavy buses shall make the vehicle information file available to the manufacturer of a subsequent step in the chain.’;
paragraph 5 is replaced by the following:
‘5. For each vehicle accompanied by a certificate of conformity or, in the case of vehicles approved in accordance with Article 45 of Regulation (EU) 2018/858, an individual vehicle approval certificate, the certificate shall include an imprint of the cryptographic hashes referred to in paragraph 3 of this Article.’;
the following paragraph is added:
‘6. In accordance with point 11 of Annex III, a manufacturer may transfer results of the simulation tool to other vehicles.’;
in Article 10(3), the following subparagraph is added:
‘Where a malfunction of the simulation tool occurs at a step in the manufacturing chain of heavy buses prior to the complete or completed manufacturing steps, the obligation under Article 9(1) to operate the simulation tool at the subsequent manufacturing steps shall be postponed for a maximum of 14 calendar days after the date on which the manufacturer at the previous step made the vehicle information file available to the manufacturer of the complete or completed step.’;
in Article 11, paragraphs 1 and 2 are replaced by the following:
‘1. The manufacturer’s records file, the vehicle information file and the certificates on CO2 emissions and fuel consumption related properties of the components, systems and separate technical units shall be stored by the vehicle manufacturer for at least 20 years after the production of the vehicle and shall be available, upon request, to the approval authority and to the Commission.
Upon request by an authorised entity of a Member State or by the Commission, the vehicle manufacturer shall provide, within 15 working days, the manufacturer’s records file or the vehicle information file.’;
Article 12 is amended as follows:
paragraph 1 is amended as follows:
point (g) is replaced by the following:
‘(g) air drag;’;
the following point (j) is added:
‘(j) electric powertrain components.’;
paragraph 2 is replaced by the following:
‘2. The CO2 emissions and fuel consumption related properties of the components, separate technical units and systems referred to in points (b) to (g), (i) and (j) of paragraph 1 of this Article shall be based either on the values determined, for each component, separate technical unit, system or if applicable their respective family, in accordance with Article 14 and certified in accordance with Article 17 (“certified values”) or, in the absence of the certified values, on the standard values determined in accordance with Article 13.’;
paragraphs 4 to 7 are replaced by the following:
‘4. The CO2 emissions and fuel consumption related properties of auxiliaries shall be based on the generic values as implemented in the simulation tool and as allocated to a vehicle based on the input information to be determined in accordance with Annex IX.
In the case of a base lorry, the CO2 emissions and fuel consumption related properties of components, separate technical units and systems referred to in paragraph 1, point (g), of this Article, which cannot be determined for the base lorries shall be based on the standard values. For components, separate technical units and systems referred to in paragraph 1, point (h), the technology with highest power losses shall be selected by the vehicle manufacturer.
In the case of vehicles exempted from the obligation to determine the CO2 emissions and fuel consumption under Article 9(1), the simulation tool input data shall include the information set out in Table 5 of Annex III.
Where the vehicle is to be registered, sold or put into service with a complete set of snow tyres and a complete set of standard tyres, the vehicle manufacturer may choose which of the tyres to use for determining the CO2 emissions. In the case of heavy buses, as long as the tyres used in the primary vehicle simulation are with the vehicle when it is registered, sold or put into service, addition of tyre sets to the vehicle shall not result in the obligation to conduct a new primary vehicle simulation in accordance with point 2 of Annex I.’;
Article 13 is amended as follows:
the heading is replaced by the following:
paragraphs 7 and 8 are replaced by the following:
‘7. For auxiliaries generic values are allocated by the simulation tool in accordance with the technologies selected in accordance with Annex IX.
The standard value for tyres shall be determined in accordance with Annex X, point 3.2.’;
the following paragraph is added:
‘9. The standard values for electric powertrain components shall be determined in accordance with Appendices 8, 9 and 10 to Annex Xb.’;
Article 14 is amended as follows:
paragraphs 1 and 2 are replaced by the following:
‘1. The values determined in accordance with paragraphs 2 to 10 of this Article may be used by the vehicle manufacturer as the simulation tool input data if they are certified in accordance with Article 17.
The certified values for engines shall be determined in accordance with points 4, 5 and 6 of Annex V.’;
the following paragraph 10 is added:
‘10. The certified values for electric powertrain components shall be determined in accordance with points 4, 5 and 6 of Annex Xb.’;
Article 15 is amended as follows:
in paragraph 1, the following indents are added:
‘— Appendix 3 to Annex V as regards engines, the certified values for the members of an engine family created in accordance with the family definition shall be derived in accordance with points 4, 5 and 6 of Annex V;
Appendix 13 to Annex Xb as regards the family concept of electric machine systems or integrated electric powertrain components, the certified values for the members of a family created in accordance with the family definition of electric machine systems, shall be derived in accordance with point 4 of Annex Xb.’;
paragraph 2 is replaced by the following:
‘2. For engines, the certified values for the members of an engine family shall be derived in accordance with points 4, 5 and 6 of Annex V.
For tyres, a family shall consist of one tyre type only.
For electric machine systems or integrated electric powertrain components, the certified values for the members of a family of electric machine systems shall be derived in accordance with point 4 of Annex Xb.’;
Article 16 is amended as follows:
paragraph 1 is replaced by the following:
‘1. The application for certification of the CO2 emissions and fuel consumption related properties of the component, separate technical unit and systems, or if applicable their respective families, shall be submitted to the approval authority.’;
in paragraph 2, the following indent is added:
‘— Appendixes 2 to 6 to Annex Xb as regards electric powertrain components.’;
paragraph 3 is replaced by the following:
‘3. The application for certification shall be accompanied by an explanation of the elements of design of the component, separate technical unit and system, or if applicable their respective families concerned which have a non-negligible effect on the CO2 emissions and fuel consumption related properties of the components, separate technical units or systems concerned.
The application shall also be accompanied by the relevant test reports issued by an approval authority, test results, and by a statement of compliance issued by an approval authority pursuant to point 2 of Annex IV to Regulation (EU) 2018/858.’;
Article 17 is amended as follows:
Paragraph 1 is replaced by the following:
‘1. If all the applicable requirements are met, the approval authority shall certify the values relating to the CO2 emissions and fuel consumption related properties of the component, separate technical unit and system, or if applicable their respective families concerned.’;
in paragraph 2, the following indent is added:
‘— Appendix 1 to Annex Xb as regards electric powertrain components.’;
in paragraph 3, the following indent is added:
‘— Appendix 14 to Annex Xb as regards electric powertrain components.’;
in paragraph 3, the second subparagraph is replaced by the following: