ANNEX V VEHICLE’S AIR DRAG DATA Determination of aerodynamic device data, Regulation (EU) 2022/1362

In forcesince 25 Aug 2022cited 1×

This Annex sets out the procedure for the determination of the aerodynamic device data.

(1)

Standard aerodynamic devices are aerodynamic devices for which standard values can be used in the vehicle certification. The standard aerodynamic device may consist of the following elements:

(a)

‘rear flaps’ means an aerodynamic device composed by two or more rear fairing panels located at the rear end of the vehicle with the aim to reduce its wake;

(b)

‘short rear flaps’ means rear flaps which lateral panels measure at least 2 meters and do not cover the total height of the body;

(c)

‘tall rear flaps’ means rear flaps which lateral panels cover the entire height of the body with a tolerance of ±3% of the total height of the body;

(d)

‘side covers’ means an aerodynamic device composed by panels located at the lower side of the vehicle with the aim to reduce the impact of crosswind and/or the turbulences created by the wheels on the air drag;

(e)

‘short side covers’ means side covers that do not cover the area of the wheels; in case of semi-trailers, they cover only the distance between the landing gear and the beginning of the first wheel;

(f)

‘long side covers’ means side covers that cover a distance between the landing gear of a semi-trailer and the rear end of the vehicle;

(2)

‘CFD’ means computational fluid dynamic simulation used for analysing complex fluid phenomena;

Based on the validation process as specified in Annex VIII, Appendix 3 to Regulation (EU) 2018/858, the certification of an aerodynamic device by means of CFD shall require the CFD method to be validated against a reference CFD method as shown in Figure 1.

The CFD method to be validated shall be applied to a set of generic geometries.

Comparability of the computer simulation results shall be proven. The manufacturer of the aerodynamic device or the technical service shall draft a validation report and submit it to the approval authority.

Any change to the CFD method or to the software that is likely to invalidate the validation report shall be brought to the attention of the approval authority, which may require that a new validation process is conducted.

Once validated, the method shall be used for certifying the aerodynamic device.

The validation process shall consist of simulating three different CFD simulation sets as follows:

(a)

BASE set:

Generic 4x2 tractor

Generic ST1 semi-trailer.

(b)

TRF set:

Generic 4x2 tractor

Generic ST1 semi-trailer

Generic tall rear flaps

(c)

LSC set:

Generic 4x2 tractor

Generic ST1 semi-trailer

Generic long side covers

Each set shall be simulated at β=0,0, 3,0 and 6,0 degrees of yaw to account for crosswind effects coming from the left hand side of the vehicle, as shown in Figure 2.

The heat exchangers pressure drop shall be modelled as per equation [1]:

dp

dx

Pi·v2Pv·v [1]

where the coefficients for each heat exchanger shall be as listed in Table 1.

Coefficient | Condenser | Charge Air Cooler | Radiator

Inertial Resistance (Pi) [kg/m4] | 140,00 | 60,00 | 120,00

Viscous Resistance (Pv)

[kg/m3s]

450,00 | 300,00 | 450,00

The CFD shall comply with the requirements listed in Table 2. The compliance for the minimum CFD requirements shall be demonstrated to the approval authority.

Field | Value | Comments

Vehicle velocity | 25,00 m/s | To be used as the drag coefficient reference velocity.

Vehicle frontal area | 10,047 m2 | To be used as the drag coefficient reference area.

Tractor Front Wheel

Rotation axis-to-Ground Vertical Distance

527,00 mm |

Semi-trailer Rear Wheel

Rotation axis-to-Ground Vertical Distance

514,64 mm |

Simulation Domain dimensions. Length | Length ≥ 145,00 m |

Simulation Domain dimensions. Width | Width ≥ 75,00 m |

Simulation Domain dimensions. Height | Height ≥ 25,00 m |

Vehicle Position

Air Inlet to Vehicle Front End Distance

≥ 25,00 m |

Vehicle Position

Air Outlet to Vehicle Rear End Distance

≥ 100,00 m |

Domain Discretization. Cell Count | ≥ 60 million cells | Mesh refinement applied to properly capture aero-relevant areas

Ground surface and wheels | 25,00 m/s | The ground surface of the simulation domain has to move backwards relative to the vehicle and the wheels of the vehicles have to rotate with the corresponding tangential velocity.

The CFD method shall fulfil an accuracy for Δ(CD×A) during the validation for each of the six comparisons with respect to the reference ranges as shown in Table 3.

Simulation set | Yaw Angle – β [deg]

0,0° | 3,0° | 6,0°

TRF | -8,6 % < Δ(CD×A) < -1,6 % | -9,0 % < Δ(CD×A) < -2,0 % | -10,3 % < Δ(CD×A) < -3,3 %

LSC | -8,8 % < Δ(CD×A) < -1,8 % | -8,0 % < Δ(CD×A) < -1,0 % | -8,1 % < Δ(CD×A) < -1,1 %

The validation report shall reflect the CD×A [m2] value for all nine CFD simulations as shown in Table 4.

The validation report shall contain all of the following:

CD×A [m2] results:

Simulation set | Yaw Angle – β [deg]

0,0° | 3,0° | 6,0°

BASE | | |

TRF | | |

LSC | | |

in the case of steady-state methods:

raw data of the evolution of CD (or CD×A) vs iteration, in *.csv format.

the average of the last 400 iterations.

in the case of transient methods:

raw data of the evolution of CD (or CD×A) vs time, in *.csv format.

the average of the last 5,0 seconds.

A XY plane section intersecting the entire simulation domain:

passing through the tractor front axle wheel rotation point,

showing the airflow velocity magnitude in a scale going from 0 to 30 m/s and with a colour bar divided in, at least, 18 colour levels as shown in Figure 3.

A XY plane section intersecting the entire simulation domain:

passing through the tractor side mirrors,

showing the airflow velocity magnitude in a scale going from 0 to 30 m/s and with a colour bar divided in, at least, 18 colour levels as shown in Figure 4.

A YZ plane section intersecting the entire simulation domain:

passing through the tractor front axle wheel rotation point,

showing the airflow velocity magnitude in a scale going from 0 to 30 m/s and with a colour bar divided in, at least, 18 colour levels as shown in Figure 5.

A XZ plane section intersecting the entire simulation domain:

passing through the centre of the vehicle,

showing the airflow velocity magnitude in a scale going from 0 to 30 m/s and with a colour bar divided in, at least, 18 colour levels as shown in Figure 6.

The XY, YZ and XZ planes use a coordinate system fixed to the vehicle as shown in Figure 7, where,

the X-axis is oriented along the longitudinal direction of the vehicle,

the Y-axis is oriented along the width of the vehicle,

the Z-axis is oriented along the height of the vehicle.

The manufacturer of the aerodynamic device shall use generic vehicle geometries to demonstrate the performance of the aerodynamic device mounted on a trailer or semi-trailer. For that purpose, the 3D model of the aerodynamic device shall be added to the generic vehicle geometries in the same position as if it were mounted on a real vehicle.

Upon agreement of an approval authority, the manufacturer of the aerodynamic device may make changes to the generic geometries if that is necessary for the correct installation or proper operation of the aerodynamic device and if that change adequately reflects reality.

The validated CFD method shall be applied to the modified geometries and Δ(CD×A) values for 4 yaw angles shall be computed: β = 0,0, 3,0, 6,0 and 9,0 degree.

The technical report shall reflect the aerodynamic benefit Δ(CD×A)[%] for all 4 yaw angles as shown in Table 5.

Δ(CD×A)(β) [%] | Yaw Angle – β [deg]

0,0° | 3,0° | 6,0° | 9,0°

Modified (semi-)trailer | | | |

computed in accordance with the following formula [2]:

ΔCDAβ

CDAβBASE CDAβMOD

CDAβBASE

100 [2]

Where,

CDAβMod is the aerodynamic resistance (in m2) of the modified geometry computed by the validated CFD method for β = 0,0, 3,0, 6,0 and 9,0 degree.

CDAβBASE is the aerodynamic resistance (in m2) of the BASE set computed by the validated CFD method for β = 0,0, 3,0, 6,0 and 9,0 degree.