ANNEX VI Technical documentation, Regulation (EU) 2019/2013

In forcesince 1 May 2021cited 1×

The technical documentation referred to in point 1(d) of Article 3 shall include:

(1)

a general description of the model allowing it to be unequivocally and easily identified;

(2)

references to the harmonised standards applied or other measurement standards used;

(3)

specific precautions to be taken when the model is assembled, installed, maintained or tested;

(4)

the values for the technical parameters set out in Table 5; these values are considered as the declared values for the purpose of the verification procedure in Annex IX;

(5)

the details and the results of calculations performed in accordance with Annex IV;

[the values of ABC luminance-related parameters are indicative, and the verification is against the applicable ABC-related requirements.]

Parameter | Parameter value and precision | Unit | Declared value

General

1 | Supplier’s name or trade mark | TEXT | |

2 | Model identifier | TEXT | |

3 | Energy efficiency class for Standard Dynamic Range (SDR) | [A/B/C/D/E/F/G] | A – G |

4 | On mode power demand in Standard Dynamic Range (SDR) | XXX,X | W |

5 | Energy efficiency class for High Dynamic Range (HDR), if implemented | [A/B/C/D/E/F/G] or n.a. | A – G |

6 | On mode power demand in High Dynamic Range (HDR) | XXX,X | W |

7 | Off mode, power demand | X,X | W |

8 | Standby mode power demand | X,X | W |

9 | Networked standby mode power demand | X,X | W |

10 | Electronic display category | [television/monitor/signage/other] | TEXT |

11 | Size ratio | XX | : | XX | |

12 | Screen resolution (pixels) | X | × | X | |

13 | Screen diagonal | XXX,X | cm |

14 | Screen diagonal | XX | inches |

15 | Visible screen area | XXX,X | dm2 |

16 | Panel technology used | TEXT | |

17 | Automatic Brightness Control (ABC) available | [YES/NO] | |

18 | Voice recognition sensor available | [YES/NO] | |

19 | Room presence sensor available | [YES/NO] | |

20 | Image refresh frequency rate (normal configuration) | XXX | Hz |

21 | Minimum guaranteed availability of software and firmware updates (from the date of end of the placement on the market (as set out in Annex II E, point 1 of Commission Regulation (EU) 2019/2021): | XX | Years |

22 | Minimum guaranteed availability of spare parts (from the date of end of the placement on the market, as set out in Annex II E, point 1 of Commission Regulation (EU) 2019/2021): | XX | Years |

23 | Minimum guaranteed product support (from the date of end of the placement on the market, as set out Annex II E, point 1 of Commission Regulation (EU) 2019/2021): | XX | Years |

Minimum duration of the general guarantee offered by the supplier | XX | Years |

For On-mode

24 | Peak white luminance of the brightest on mode configuration | XXXX | cd/m2 |

25 | Peak white luminance of the normal configuration | XXXX | cd/m2 |

26 |

Peak white luminance ratio (calculated as

value of ‘Peak white luminance of the normal configuration’ divided by value of ‘Peak white luminance of the brightest on mode configuration’ multiplied by 100)

XX,X | % |

For Auto Power Down (APD)

27 | Length of time in on mode before the electronic display automatically switches to standby, off mode, or another condition which does not exceed the applicable power demand requirements for off mode or standby mode. | XX:XX | mm:ss |

28 | For televisions: the length of time, following the last user interaction, before the television automatically switches to standby, off-mode, or another condition which does not exceed the applicable power consumption requirements for off-mode or standby-mode; | XX:XX | mm:ss |

29 | For televisions equipped with room presence sensor: the length of time, when no presence is detected, before the television automatically switches to standby, off-mode, or another condition which does not exceed the applicable power demand requirements for off mode or standby mode; | XX:XX | mm:ss |

30 | For electronic displays other than televisions and broadcast displays: the length of time, when no input is detected, before the electronic display automatically switches to standby, off-mode, or another condition which does not exceed the applicable power consumption requirements for off mode or standby mode; | XX:XX | mm:ss |

For ABC

If available and activated by default

31 | Percentage of power reduction due to ABC action between the 100 lux and 12 lux ambient light conditions. | XX,X | % |

32 | On mode power at 100 lux ambient light at the ABC sensor | XXX,X | W |

33 | On mode power at 12 lux ambient light at the ABC sensor | XXX,X | W |

34 | Screen luminance at 100 lux ambient light at the ABC sensor | XXX | cd/m2 |

35 | Screen luminance at 60 lux ambient light at the ABC sensor | XXX | cd/m2 |

36 | Screen luminance at 35 lux ambient light at the ABC sensor | XXX | cd/m2 |

37 | Screen luminance at 12 lux ambient light at the ABC sensor | XXX | cd/m2 |

For Power Supply

38 | Power supply type | Internal/External | |

39 | Standard references (if relevant) | | TEXT |

40 | Input voltage | XXX,X | V |

41 | Output voltage | XXX,X | V |

42 | Input current (max) | XXX,X | A |

43 | Output current (min) | XXX,X | A |

(6)

testing conditions if not described sufficiently in point (2);

(7)

equivalent models, if any, including model identifiers;

These elements shall also constitute the mandatory specific parts of the technical documentation that the supplier shall enter into the database, pursuant to point 5 of Article 12 of Regulation (EU) 2017/1369.

(9)

Additional information requirements:

(a)

input terminal for the audio and video test signals used for testing;

(b)

information and documentation on the instrumentation, set-up and circuits used for electrical testing;

(c)

any other testing condition not described or determined in point (b);

(d)

for on mode:

(i)

the characteristics of the dynamic broadcast-content video signal representing typical broadcast TV content; for the HDR dynamic broadcast content video signal the electronic display must be automatically switched to HDR mode by the HDR metadata of that signal;

(ii)

the sequence of steps for achieving a stable condition with respect to power demand level; and

(iii)

the picture settings used for the brightest peak white luminance measurement and the test pattern for the video signal used for the measurement.

(e)

For standby and off mode:

(i)

the measurement method used;

(ii)

description of how the mode was selected or programmed including any enhanced reactivation functions; and

(iii)

sequence of events to reach the condition where the electronic display automatically changes mode.

(f)

For electronic displays with a designated computer signal interface:

(i)

confirmation that the electronic display prioritises the computer display power management protocols set out in point 6.2.3 of Annex II of Commission Regulation (EU) No 617/2013 [Commission Regulation (EU) No 617/2013 of 26 June 2013 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for computers and computer servers (OJ L 175, 27.6.2013, p. 13).]. Any deviation from the protocols should be reported;

(g)

For the networked electronic displays only:

(i)

number and type of network interfaces and, except for wireless network interfaces, their position in the electronic display;

(ii)

whether the electronic display qualifies as electronic display with HiNA functionality; if no information is provided the electronic display is considered not to be HiNA display or display with HiNA functionality; and

(iii)

information whether networked electronic display provides functionality allowing the power management function and/or the end-user to switch the electronic display being in a condition providing networked standby into standby mode, or off mode or another condition which does not exceed the applicable power demand requirements for off mode and/or standby mode including enhanced reactivation function power allowance where applicable.

(h)

For each type of network port:

(i)

the default time (mm:ss) after which the power management function, switches the display into a condition providing networked standby; and

(ii)

the trigger to be used to reactivate the electronic display.

(10)

where the information included in the technical documentation file for a particular electronic display model has been obtained:

(a)

from a model that has the same technical characteristics relevant for the technical information to be provided but is produced by a different manufacturer or

(b)

by calculation on the basis of design or by extrapolation from another model of the same or of a different supplier, or both;

the technical documentation shall include, as appropriate, the details of such calculation, the assessment undertaken by suppliers to verify the accuracy of the calculation and, where appropriate, the declaration of identity between the models of different suppliers; and

(11)

the contact details of the person empowered to bind the supplier, if not included in the technical information uploaded into the database, shall be made available, on request, to market surveillance authorities or to the Commission for carrying out their tasks under this Regulation.