ANNEX II, Regulation (EU) 2017/1509

In forcesince 30 Jul 2024cited 3×

The notes, acronyms and abbreviations, and the definitions in Annex I to Regulation (EC) No 428/2009 apply for the purpose of this Annex.

All goods and technology listed in Annex I to Regulation (EC) No 428/2009.

Other items, materials, equipment, goods and technology which could contribute to DPRK's nuclear-related, other weapons of mass destruction-related or ballistic missile-related programmes.

Unless otherwise stated, reference numbers used in the column entitled ‘Description’ refer to the descriptions of dual use items and technology set out in Annex I to Regulation (EC) No 428/2009.

A reference number in the column entitled ‘Related item from Annex I to Regulation (EC) No 428/2009’ means that the characteristics of the item described in the column ‘Description’ lie outside the parameters set out in the description of the dual use entry referred to.

Definitions of terms between ‘single quotation marks’ are given in a technical note to the relevant item.

Definitions of terms between "double quotation marks" can be found in Annex I to Regulation (EC) No 428/2009, except the following:

The object of the prohibitions contained in this Annex should not be defeated by the export of any non-prohibited goods (including plant) containing one or more prohibited components when the prohibited component or components are the principal element of the goods and can feasibly be removed or used for other purposes.

N.B.: In judging whether the prohibited component or components are to be considered the principal element, it is necessary to weigh the factors of quantity, value and technological know-how involved and other special circumstances which might establish the prohibited component or components as the principal element of the goods being procured.

Goods specified in this Annex include both new and used goods.

The sale, supply, transfer or export of "technology" which is "required" for the "development", "production" or "use" of goods the sale, supply, transfer or export of which is prohibited in Part A (Goods), is prohibited in accordance with the provisions of Part B.

The "technology" "required" for the "development", "production" or "use" of prohibited goods remains under prohibition even when applicable to non-prohibited goods.

Prohibitions do not apply to that "technology" which is the minimum necessary for the installation, operation, maintenance (checking) and repair of those goods which are not prohibited.

Prohibitions on "technology" transfer do not apply to information "in the public domain", to "basic scientific research" or to the minimum necessary information for patent applications.

No | Description | Related item from Annex I to Regulation (EC) No 428/2009

II.

A0.001 |

Hollow cathode lamps as follows:

a.

Iodine hollow cathode lamps with windows in pure silicon or quartz;

b.

Uranium hollow cathode lamps.

N/A

II.

A0.002 | Faraday isolators in the wavelength range 500 nm – 650 nm. | N/A

II.

A0.003 | Optical gratings in the wavelength range 500 nm – 650 nm. | N/A

II.

A0.004 |

Optical fibres in the wavelength range 500 nm – 650 nm coated with anti-reflecting layers in the wavelength range

500 nm – 650 nm and having a core diameter greater than 0,4 mm but not exceeding 2 mm.

N/A

II.

A0.005 |

Nuclear reactor vessel components and testing equipment, other than those specified in 0A001, as follows:

a.

Seals;

b.

Internal components;

c.

Sealing, testing and measurement equipment.

0A001

II.

A0.006 |

Nuclear detection systems, other than those specified in 0A001.j. or 1A004.c., for detection, identification or quantification of radioactive materials or radiation of nuclear origin and specially designed components thereof.

N.B: For personal equipment refer to II.A1.004 below.

0A001.j.

1A004.c.

II.

A0.007 | Bellows-sealed valves other than those specified in 0B001.c.6., 2A226 or 2B350, made of aluminium alloy or stainless steel type 304, 304L or 316L. |

0B001.c.6.

2A226

2B350

II.

A0.008 |

Laser mirrors, other than those specified in 6A005.e., consisting of substrates having a thermal expansion coefficient of 10– 6 K– 1 or less at 20 °C (e.g. fused silica or sapphire).

Note: This item does not cover optical systems specially designed for astronomical applications, except if the mirrors contain fused silica.

0B001.g.5.

6A005.e.

II.

A0.009 | Laser lenses, other than those specified in 6A005.e.2, consisting of substrates having a thermal expansion coefficient of 10– 6 K– 1 or less at 20 °C (e.g. fused silica). |

0B001.g.

6A005.e.2.

II.

A0.010 | Pipes, piping, flanges, fittings made of, or lined with nickel, or nickel alloy containing more than 40 % nickel by weight, other than those specified in 2B350.h.1. | 2B350

II.

A0.011 |

Vacuum pumps other than those specified in 0B002.f.2. or 2B231, as follows:

a.

Turbo-molecular pumps having a flow-rate equal to or greater than 400 l/s;

b.

Roots type vacuum roughing pumps having a volumetric aspiration flow-rate greater than 200 m3/h;

c.

Bellows-sealed, scroll, dry compressor, and bellows-sealed, scroll, dry vacuum pumps.

0B002.f.2.

2B231

II.

A0.012 | Shielded enclosures for the manipulation, storage and handling of radioactive substances (hot cells). | 0B006

II.

A0.013 | ‘Natural uranium’ or ‘depleted uranium’ or thorium in the form of metal, alloy, chemical compound or concentrate and any other material containing one or more of the foregoing, other than those specified in 0C001. | 0C001

II.

A0.014 | Detonation chambers having a capacity of explosion absorption of more than 2,5 kg TNT equivalent. | N/A

No | Description | Related item from Annex I to Regulation (EC) No 428/2009

II.

A1.001 | Bis(2-ethylhexyl) phosphoric acid (HDEHP or D2HPA) Chemical Abstract Number (CAS): [CAS 298-07-7] solvent in any quantity, with a purity greater than 90 %. | N/A

II.

A1.002 | Fluorine gas CAS: [7782-41-4], with a purity of at least 95 %. | N/A

II.

A1.003 |

Ring-shaped seals and gaskets, having an inner diameter of 400 mm or less, made of any of the following materials:

a.

Copolymers of vinylidene fluoride having 75 % or more beta crystalline structure without stretching;

b.

Fluorinated polyimides containing 10 % by weight or more of combined fluorine;

c.

Fluorinated phosphazene elastomers containing 30 % by weight or more of combined fluorine;

d.

Polychlorotrifluoroethylene (PCTFE, e.g. Kel-F ®);

e.

Fluoro-elastomers (e.g. Viton ®, Tecnoflon ®);

f.

Polytetrafluoroethylene (PTFE).

1A001

II.

A1.004 | Personal equipment for detecting radiation of nuclear origin, other than that specified in 1A004.c., including personal dosimeters. | 1A004.c.

II.

A1.005 | Electrolytic cells for fluorine production, other than those specified in 1B225, with an output capacity greater than 100 g of fluorine per hour. | 1B225

II.

A1.006 | Catalysts, other than those specified in 1A225 or 1B231, containing platinum, palladium or rhodium, usable for promoting the hydrogen isotope exchange reaction between hydrogen and water for the recovery of tritium from heavy water or for the production of heavy water. |

1A225

1B231

II.

A1.007 |

Aluminium and its alloys, other than those specified in 1C002.b.4. or 1C202.a., in crude or semi-fabricated form having either of the following characteristics:

a.

‘Capable of’ an ultimate tensile strength of 460 MPa or more at 293 K (20 °C); or

b.

Having a tensile strength of 415 MPa or more at 298 K (25 °C).

The phrase alloys ‘capable of’ encompasses alloys before or after heat treatment.

1C002.b.4.

1C202.a.

II.

A1.008 |

Magnetic metals, of all types and of whatever form, other than those specified in 1C003.a. having an ‘initial relative permeability’ of 120000 or more and a thickness between 0,05 mm and 0,1 mm.

Measurement of ‘initial relative permeability’ must be performed on fully annealed materials.

1C003.a.

II.

A1.009 |

‘Fibrous or filamentary materials’ or prepregs, other than those specified in 1C010.a., 1C010.b., 1C210.a. or 1C210.b., as follows:

a.

Aramid ‘fibrous or filamentary materials’ having either of the following characteristics:

1.

A ‘specific modulus’ exceeding 10 × 106 m; or

2.

A ‘specific tensile strength’ exceeding 17 × 104 m;

b.

Glass ‘Gfibrous or filamentary materials’ having either of the following characteristics:

1.

A ‘specific modulus’ exceeding 3,18 × 106 m; or

2.

A ‘specific tensile strength’ exceeding 76,2 × 103 m;

c.

Thermoset resin-impregnated continuous ‘yarns’, ‘rovings’, ‘tows’ or ‘tapes’ with a width of 15 mm or less (once prepregs), made from glass ‘fibrous or filamentary materials’ other than those specified in I.A1.010.a. below;

d.

Carbon ‘fibrous or filamentary materials’;

e.

Thermoset resin-impregnated continuous ‘yarns’, ‘rovings’, ‘tows’, or ‘tapes’, made from carbon ‘fibrous or filamentary materials’;

f.

Polyacrylonitrile (PAN) continuous ‘yarns’, ‘rovings’, ‘tows’ or ‘tapes’;

g.

Para-aramid ‘fibrous or filamentary materials’ (Kevlar® and other Kevlar®-like fibres).

1C010.a.

1C010.b.

1C210.a.

1C210.b.

II.

A1.010 |

Resin-impregnated or pitch-impregnated fibres (prepregs), metal or carbon-coated fibres (preforms) or ‘carbon fibre preforms’, as follows:

a.

Made from ‘fibrous or filamentary materials’ specified in II.A1.009 above;

b.

Epoxy resin ‘matrix’ impregnated carbon ‘fibrous or filamentary materials’ (prepregs), specified in 1C010.a., 1C010.b. or 1C010.c., for the repair of aircraft structures or laminates, of which the size of individual sheets does not exceed 50 cm × 90 cm;

c.

Prepregs specified in 1C010.a., 1C010.b. or 1C010.c., when impregnated with phenolic or epoxy resins having a glass transition temperature (Tg) less than 433 K (160 °C) and a cure temperature lower than the glass transition temperature.

1C010

1C210

II.

A1.011 | Reinforced silicon carbide ceramic composites usable for nose tips, re-entry vehicles, nozzle flaps, usable in ‘missiles’, other than those specified in 1C107. | 1C107

II.

A1.012 | Not used. |

II.

A1.013 |

Tantalum, tantalum carbide, tungsten, tungsten carbide and alloys thereof, other than those specified in 1C226, having both of the following characteristics:

a.

In forms having a hollow cylindrical or spherical symmetry (including cylinder segments) with an inside diameter between 50 mm and 300 mm; and

b.

A mass greater than 5 kg.

1C226

II.

A1.014 |

‘Elemental powders’ of cobalt, neodymium or samarium or alloys or mixtures thereof containing at least 20 % by weight of cobalt, neodymium or samarium, with a particle size less than 200 μm.

Technical note: ‘Elemental powder’ means a high purity powder of one element.

N/A

II.

A1.015 | Pure tributyl phosphate (TBP) [CAS No 126-73-8] or any mixture having a TBP content of more than 5 % by weight. | N/A

II.

A1.016 |

Maraging steel, other than those specified by 1C116 or 1C216.

1.

The phrase maraging steel ‘capable of’ encompasses maraging steel before or after heat treatment.

2.

Maraging steels are iron alloys generally characterised by high nickel, very low carbon content and the use of substitutional elements or precipitates to produce strengthening and age-hardening of the alloy.

1C116

1C216

II.

A1.017 |

Metals, metal powders and material as follows:

a.

Tungsten and tungsten alloys, other than those specified in 1C117, in the form of uniform spherical or atomized particles of 500 μm (micrometre) diameter or less with a tungsten content of 97 % by weight or more;

b.

Molybdenum and molybdenum alloys, other than those specified in 1C117, in the form of uniform spherical or atomized particles of 500 μm diameter or less with a molybdenum content of 97 % by weight or more;

c.

Tungsten materials in the solid form, other than those specified in 1C226 having material compositions as follows:

1.

Tungsten and alloys containing 97 % by weight or more of tungsten;

2.

Copper infiltrated tungsten containing 80 % by weight or more of tungsten; or

3.

Silver infiltrated tungsten containing 80 % by weight or more of tungsten.

1C117

1C226

II.

A1.018 |

Soft magnetic alloys, other than those specified in 1C003, having a chemical composition as follows:

a.

Iron content between 30 % and 60 %; and

b.

Cobalt content between 40 % and 60 %.

1C003

II.

A1.019 | Not used. |

II.

A1.020 | Graphite, other than that specified in 0C004 or 1C107.a., designed or specified for use in Electrical Discharge Machining (EDM) machines. |

0C004

1C107.a.

II.

A1.021 |

Steel alloys in sheet or plate form, having any of the following characteristics:

(a)

Steel alloys ‘capable of’ ultimate tensile strength of 1200 MPa or more, at 293 K (20 °C); or

(b)

Nitrogen-stabilised duplex stainless steel.

Note: the phrase alloys ‘capable of’ encompasses alloys before or after heat treatment.

Technical note: ‘nitrogen-stabilised duplex stainless steel’ has a two-phase microstructure consisting of grains of ferritic and austenitic steel with the addition of nitrogen to stabilise the microstructure.

1C116

1C216

II.

A1.022 | Carbon-Carbon Composite material. | 1A002.b.1

II.

A1.023 | Nickel alloys in crude or semi-fabricated form, containing 60 % by weight or more nickel. | 1C002.c.1.a

II.

A1.024 |

Titanium alloys in sheet or plate form ‘capable of’ an ultimate tensile strength of 900 MPa or more at 293 K (20 °C).

Note: the phrase alloys ‘capable of’ encompasses alloys before or after heat treatment.

1C002.b.3

II.

A1.025 | Titanium alloys, other than those specified in 1C002 and 1C202. |

1C002

1C202

II.

A1.026 | Zirconium and zirconium alloys, other than those specified in 1C011, 1C111 and 1C234. |

1C011

1C111

1C234

II.

A1.027 | Explosive materials other than those specified in 1C239, or materials or mixtures containing more than 2 % by weight of such explosive materials, with a crystalline density higher than 1,5 g/cm3 and with a detonation speed higher than 5000 m/s. | 1C239

No | Description | Related item from Annex I to Regulation (EC) No 428/2009

II.

A2.001 |

Vibration test systems, equipment and components thereof, other than those specified in 2B116:

a.

Vibration test systems employing feedback or closed loop techniques and incorporating a digital controller, capable of vibrating a system at an acceleration equal to or greater than 0,1 g rms between 0,1 Hz and 2 kHz and imparting forces equal to or greater than 50 kN, measured ‘bare table’;

b.

Digital controllers, combined with specially designed vibration test ‘software’, with a ‘real-time control bandwidth’ greater than 5 kHz designed for use with vibration test systems specified in a.;

Technical note:‘Real-time control bandwidth’ is defined as the maximum rate at which a controller can execute complete cycles of sampling, processing data and transmitting control signals.

c.

Vibration thrusters (shaker units), with or without associated amplifiers, capable of imparting a force equal to or greater than 50 kN, measured ‘bare table’, and usable in vibration test systems specified in a.;

d.

Test piece support structures and electronic units designed to combine multiple shaker units in a system capable of providing an effective combined force equal to or greater than 50 kN, measured ‘bare table’, and usable in vibration systems specified in a.

Technical note: ‘bare table’ means a flat table, or surface, with no fixture or fittings.

2B116

II.

A2.002 |

Machine tools, other than those specified in 2B001 or 2B201 and any combination thereof, for removing (or cutting) metals, ceramics, or ‘composites’ that, according to the manufacturer's technical specification, can be equipped with electronic devices for ‘numerical control’, having positioning accuracies of equal to or less (better) than 30 μm according to ISO 230/2 (1988) or national equivalents along any linear axis.

Technical note: Manufacturers calculating positioning accuracy in accordance with ISO 230/2 (1997) should consult the competent authorities of the Member State in which they are established.

2B001

2B201

II.

A2.002a | Components and numerical controls, specially designed for machine tools specified in 2B001, 2B201 or I.A2.002 above. | N/A

II.

A2.003 |

Balancing machines and related equipment as follows:

a.

Balancing machines, designed or modified for dental or other medical equipment, having all the following characteristics:

1.

Not capable of balancing rotors/assemblies having a mass greater than 3 kg;

2.

Capable of balancing rotors/assemblies at speeds greater than 12500 rpm;

3.

Capable of correcting unbalance in two planes or more; and

4.

Capable of balancing to a residual specific unbalance of 0,2 g × mm per kg of rotor mass;

b.

‘Indicator heads’ designed or modified for use with machines specified in a. above.

Technical note: ‘Indicator heads’ are sometimes known as balancing instrumentation.

2B119

II.

A2.004 |

Remote manipulators that can be used to provide remote actions in radiochemical separation operations or hot cells, other than those specified in 2B225, having either of the following characteristics:

a.

A capability of penetrating a hot cell wall of 0,3 m or more (through the wall operation); or

b.

A capability of bridging over the top of a hot cell wall with a thickness of 0,3 m or more (over the wall operation).

Technical note: Remote manipulators provide translation of human operator actions to a remote operating arm and terminal fixture. They may be of master/slave type or operated by joystick or keypad.

2B225

II.

A2.005 |

Controlled atmosphere heat treatment furnaces or oxidation furnaces capable of operation at temperatures above 400 °C.

Note: This item does not cover tunnel kilns with roller or car conveyance, tunnel kilns with conveyor belt, pusher type kilns or shuttle kilns, specially designed for the production of glass, tableware ceramics or structural ceramics.

2B226

2B227

II.

A2.006 | Not used. |

II.

A2.007 |

‘Pressure transducers’, other than those defined in 2B230, capable of measuring absolute pressures at any point in the range 0 to 200 kPa and having both of the following characteristics:

a.

Pressure sensing elements made of or protected by ‘Materials resistant to corrosion by uranium hexafluoride (UF6)’; and

b.

Having either of the following characteristics:

1.

A full scale of less than 200 kPa and an ‘accuracy’ of better than ± 1 % of full scale; or

2.

A full scale of 200 kPa or greater and an ‘accuracy’ of better than 2 kPa.

Technical note: For the purposes of 2B230 ‘accuracy’ includes non-linearity, hysteresis and repeatability at ambient temperature.

2B230

II.

A2.008 |

Liquid-liquid contacting equipment (mixer-settlers, pulsed columns, plate columns, centrifugal contactors); and liquid distributors, vapour distributors or liquid collectors designed for such equipment, where all surfaces that come in direct contact with the chemical(s) being processed are made from any of the following materials:

a.

Alloys with more than 25 % nickel and 20 % chromium by weight;

b.

Fluoropolymers;

c.

Glass (including vitrified or enamelled coating or glass lining);

d.

Graphite or ‘carbon graphite’;

e.

Nickel or alloys with more than 40 % nickel by weight;

f.

Tantalum or tantalum alloys;

g.

Titanium or titanium alloys;

h.

Zirconium or zirconium alloys; or

i.

Stainless steel.

Technical note: ‘Carbon graphite’ is a composition consisting of amorphous carbon and graphite, in which the graphite content is 8 % or more by weight.

2B350.e.

II.

A2.009 |

Industrial equipment and components, other than those specified in 2B350.d., as follows:

Heat exchangers or condensers with a heat transfer surface area greater than 0,05 m2, and less than 30 m2; and tubes, plates, coils or blocks (cores) designed for such heat exchangers or condensers, where all surfaces that come in direct contact with the fluid(s) are made from any of the following materials:

a.

Alloys with more than 25 % nickel and 20 % chromium by weight;

b.

Fluoropolymers;

c.

Glass (including vitrified or enamelled coating or glass lining);

d.

Graphite or ‘carbon graphite’;

e.

Nickel or alloys with more than 40 % nickel by weight;

f.

Tantalum or tantalum alloys;

g.

Titanium or titanium alloys;

h.

Zirconium or zirconium alloys;

i.

Silicon carbide;

j.

Titanium carbide; or

k.

Stainless steel.

Note: This item does not cover vehicle radiators.

Technical note: The materials used for gaskets and seals and other implementation of sealing functions do not determine the status of control of the heat exchanger.

2B350.d.

II.

A2.010 |

Multiple-seal, and seal-less pumps, other than those specified in 2B350.i, suitable for corrosive fluids, or vacuum pumps and casings (pump bodies), preformed casing liners, impellers, rotors or jet pump nozzles designed for such pumps, in which all surfaces that come in direct contact with the chemical(s) being processed are made from any of the following materials:

a.

Alloys with more than 25 % nickel and 20 % chromium by weight;

b.

Ceramics;

c.

Ferrosilicon;

d.

Fluoropolymers;

e.

Glass (including vitrified or enamelled coatings or glass lining);

f.

Graphite or ‘carbon graphite’;

g.

Nickel or alloys with more than 40 % nickel by weight;

h.

Tantalum or tantalum alloys;

i.

Titanium or titanium alloys;

j.

Zirconium or zirconium alloys;

k.

Niobium (columbium) or niobium alloys;

l.

Stainless steel;

m.

Aluminium alloys; or

n.

Rubber.

Technical notes: The materials used for gaskets and seals and other implementations of sealing functions do not determine the status of control of the pump.

The term ‘rubber’ encompasses all kinds of natural and synthetic rubbers.

2B350.i.

II.

A2.011 |

‘Centrifugal separators’, other than those specified in 2B352.c., capable of continuous separation without the propagation of aerosols and manufactured from:

a.

Alloys with more than 25 % nickel and 20 % chromium by weight;

b.

Fluoropolymers;

c.

Glass (including vitrified or enamelled coating or glass lining);

d.

Nickel or alloys with more than 40 % nickel by weight;

e.

Tantalum or tantalum alloys;

f.

Titanium or titanium alloys; or

g.

Zirconium or zirconium alloys.

‘Centrifugal separators’ include decanters.

2B352.c.

II.

A2.012 | Sintered metal filters, other than those specified in 2B352.d., made of nickel or nickel alloy with more than 40 % nickel by weight. | 2B352.d.

II.

A2.013 |

Spin-forming machines and flow-forming machines, other than those specified by 2B009, 2B109 or 2B209 and specially designed components therefor.

Technical note: For the purpose of this item, machines combining the functions of spin-forming and flow-forming are regarded as flow-forming machines.

2B009

2B109

2B209

II.

A2.014 |

Equipment and reagents, other than those specified in 2B350 or 2B352, as follows:

a.

Fermenters capable of cultivation of pathogenic ‘micro-organisms’ or viruses, or capable of toxin production, without the propagation of aerosols, and having a total capacity of 10 l or more;

b.

Agitators for fermenters as mentioned in a. above;

This article is long: the rest is at the official publication.