ANNEX III, Regulation (EU) 2016/1824

In forcesince 14 Jul 2016

The Annexes to Delegated Regulation (EU) No 134/2014 are amended as follows:

(1)

Annex II is amended as follows:

(a)

points 4.5.5.2.1.1. and 4.5.5.2.1.2. are replaced by the following:

Upshift speeds (v1→2 and vi→i + 1) in km/h during acceleration phases shall be calculated using the following formulae:

Equation 2-3:

v1→20,5753e 1,9Pnmk0,1snidlenidle1ndv1

Equation 2-4:

vi→i10,5753e 1,9Pnmksnidlenidle1ndvi2, i = 2 to ng – 1

where:

‘i’ is the gear number (≥ 2)

‘ng’ is the total number of forward gears

‘Pn’ is the rated power in kW

‘mk’ is the reference mass in kg

‘nidle’ is the idling speed in min– 1

‘s’ is the rated engine speed in min– 1

‘ndvi’ is the ratio between engine speed in min– 1 and vehicle speed in km/h in gear ‘i’

4.5.5.2.1.2.

Downshift speeds (vi→i – 1) in km/h during cruise or deceleration phases in gears 4 (4th gear) to ng shall be calculated using the following formula:

Equation 2-5:

vi→i10,5753e 1,9Pnmksnidlenidle1ndvi2, i = 4 to ng

where:

i is the gear number (≥ 4)

ng is the total number of forward gears

Pn is the rated power in kW

mk is the reference mass in kg

nidle is the idling speed in min– 1

s is the rated engine speed in min– 1

ndvi-2 is the ratio between engine speed in min– 1 and vehicle speed in km/h in gear i – 2

The downshift speed from gear 3 to gear 2 (v3→2) shall be calculated using the following equation:

Equation 2-6:

v3→20,5753e 1,9Pnmk0,1snidlenidle1ndv1

where:

Pn is the rated power in kW

mk is the reference mass in kg

nidle is the idling speed in min– 1

s is the rated engine speed in min– 1

ndv1 is the ratio between engine speed in min– 1 and vehicle speed in km/h in gear 1

The downshift speed from gear 2 to gear 1 (v2→1) shall be calculated using the following equation:

Equation 2-7:

v2→10,03snidlenidle1ndv2

where:

ndv2 is the ratio between engine speed in min– 1 and vehicle speed in km/h in gear 2

Since the cruise phases are defined by the phase indicator, slight speed increases could occur and it may be appropriate to apply an upshift. The upshift speeds (v1→2, v2→3 and vi→i + 1) in km/h during cruise phases shall be calculated using the following equations:

Equation 2-7a:

v1→20,03snidlenidle1ndv2

Equation 2-8:

v2→30,5753e 1,9Pnmk0,1snidlenidle1ndv1

Equation 2-9:

vi→i10,5753e 1,9Pnmksnidlenidle1ndvi1, i = 3 to ng’

(b)

points 6.1.1.4.2. to 6.1.1.4.7. are replaced by the following:

The mass of unburned hydrocarbons emitted by the exhaust of the vehicle during the test shall be calculated using the following formula:

Equation 2-33:

HCm1

S

VdHC

HCC

106

where:

HCm is the mass of hydrocarbons emitted during the test part, in mg/km;

S is the distance defined in point 6.1.1.3.;

V is the total volume, defined in point 6.1.1.4.1.;

dHC is the density of the hydrocarbons at reference temperature and pressure (273,2 K and 101,3 kPa);

dHC

0,631 · 103 mg/m3 for petrol (E5) (C1H1,89O0,016);

= 932 · 103 mg/m3 for ethanol (E85) (C1H2,74O0,385);

= 622 · 103 mg/m3 for diesel (B5) (C1Hl,86O0,005);

= 649 · 103 mg/m3 for LPG (C1H2,525);

= 714 · 103 mg/m3 for NG/biogas (C1H4);

= 9,104A1361524,1520,583A106 mg/m3 for H2NG (with A = NG/biomethane quantity within the H2NG mixture in (volume %)).

HCc is the concentration of diluted gases, expressed in parts per million (ppm) of carbon equivalent (e.g. the concentration in propane multiplied by three), corrected to take account of the dilution air by the following equation:

Equation 2-34:

HCcHCeHCd11

DiF

where:

HCe is the concentration of hydrocarbons expressed in parts per million (ppm) of carbon equivalent, in the sample of diluted gases collected in bag(s) A;

HCd is the concentration of hydrocarbons expressed in parts per million (ppm) of carbon equivalent, in the sample of dilution air collected in bag(s) B;

DiF is the coefficient defined in point 6.1.1.4.7.

The non-methane hydrocarbon (NMHC) concentration is calculated as follows:

Equation 2-35:

CNMHC = CTHC – (Rf CH4 · CCH4)

where:

CNMHC = corrected concentration of NMHC in the diluted exhaust gas, expressed in ppm carbon equivalent;

CTHC = concentration of total hydrocarbons (THC) in the diluted exhaust gas, expressed in ppm carbon equivalent and corrected by the amount of THC contained in the dilution air;

CCH4 = concentration of methane (CH4) in the diluted exhaust gas, expressed in ppm carbon equivalent and corrected by the amount of CH4 contained in the dilution air;

Rf CH4 is the FID response factor to methane as defined in point 5.2.3.4.1.

The mass of carbon monoxide emitted by the exhaust of the vehicle during the test shall be calculated using the following formula:

Equation 2-36:

COm1

S

VdCO

COC

106

where:

COm is the mass of carbon monoxide emitted during the test part, in mg/km;

S is the distance defined in point 6.1.1.3.;

V is the total volume defined in point 6.1.1.4.1.;

dCO is the density of the carbon monoxide, dCO = 1,25 · 106 mg/m3 at reference temperature and pressure (273,2 K and 101,3 kPa);

COc is the concentration of diluted gases, expressed in parts per million (ppm) of carbon monoxide, corrected to take account of the dilution air by the following equation:

Equation 2-37:

COcCOeCOd11

DiF

where:

COe is the concentration of carbon monoxide expressed in parts per million (ppm), in the sample of diluted gases collected in bag(s) A;

COd is the concentration of carbon monoxide expressed in parts per million (ppm), in the sample of dilution air collected in bag(s) B;

DiF is the coefficient defined in point 6.1.1.4.7.

The mass of nitrogen oxides emitted by the exhaust of the vehicle during the test shall be calculated using the following formula:

Equation 2-38:

NOxm1

S

VdNO2

NOxcKh

106

where:

NOxm is the mass of nitrogen oxides emitted during the test part, in mg/km;

S is the distance defined in point 6.1.1.3.;

V is the total volume defined in point 6.1.1.4.1.;

dNO2 is the density of the nitrogen oxides in the exhaust gases, assuming that they will be in the form of nitric oxide, dNO2 = 2,05 · 106 mg/m3 at reference temperature and pressure (273,2 K and 101,3 kPa);

NOxc is the concentration of diluted gases, expressed in parts per million (ppm), corrected to take account of the dilution air by the following equation:

Equation 2-39:

NOxcNOxeNOxd11

DiF

where:

NOxe is the concentration of nitrogen oxides expressed in parts per million (ppm) of nitrogen oxides, in the sample of diluted gases collected in bag(s) A;

NOxd is the concentration of nitrogen oxides expressed in parts per million (ppm) of nitrogen oxides, in the sample of dilution air collected in bag(s) B;

DiF is the coefficient defined in point 6.1.1.4.7.

Kh is the humidity correction factor, calculated using the following formula:

Equation 2-40:

Kh110,0329H10,7

where:

H is the absolute humidity in g of water per kg of dry air:

Equation 2-41:

H6,2111UPd

PaPd

U

100

where:

U is the humidity as a percentage;

Pd is the saturated pressure of water at the test temperature, in kPa;

Pa is the atmospheric pressure in kPa.

Particulate emission Mp (mg/km) is calculated by means of the following equation:

Equation 2-42:

MpVmixVepPeVepd

where exhaust gases are vented outside the tunnel;

Equation 2-43:

Mp

VmixPe

VepS

where exhaust gases are returned to the tunnel;

where:

Vmixvolume V of diluted exhaust gases under standard conditions;

Vepvolume of exhaust gas flowing through particulate filter under standard conditions;

Peparticulate mass collected by filter(s) in mg;

Sis the distance defined in point 6.1.1.3.;

Mpparticulate emission in mg/km.

Where correction for the particulate background level from the dilution system has been used, this shall be determined in accordance with point 5.2.1.5. In this case, the particulate mass (mg/km) shall be calculated as follows:

Equation 2-44:

MpPeVepPaVap11

DiF

VmixVep

d

where exhaust gases are vented outside the tunnel;

Equation 2-45:

MpPeVepPaVap11

DiF

Vmixd

where exhaust gases are returned to the tunnel;

where:

Vap = volume of tunnel air flowing through the background particulate filter under standard conditions;

Pa = particulate mass collected by background filter;

DiF is the coefficient defined in point 6.1.1.4.7.

Where application of a background correction results in a negative particulate mass (in mg/km), the result shall be considered to be zero mg/km particulate mass.

The mass of carbon dioxide emitted by the exhaust of the vehicle during the test shall be calculated using the following formula:

Equation 2-46:

CO2m1

S

VdCO2

CO2c

102

where:

CO2m is the mass of carbon dioxide emitted during the test part, in g/km;

S is the distance defined in point 6.1.1.3.;

V is the total volume defined in point 6.1.1.4.1.;

dCO2 is the density of the carbon monoxide, dCO2 = 1,964 · 103 g/m3 at reference temperature and pressure (273,2 K and 101,3 kPa);

CO2c is the concentration of diluted gases, expressed as a percentage of carbon dioxide equivalent, corrected to take account of the dilution air by the following equation:

Equation 2-47:

CO2cCO2eCO2d11

DiF

where:

CO2e is the concentration of carbon dioxide expressed as a percentage of the sample of diluted gases collected in bag(s) A;

CO2d is the concentration of carbon dioxide expressed as a percentage of the sample of dilution air collected in bag(s) B;

DiF is the coefficient defined in point 6.1.1.4.7.

The dilution factor is calculated as follows:

For each reference fuel, except hydrogen:

Equation 2-48:

DiF

X

CCO2CHCCCO104

For a fuel of composition CxHyOz, the general formula is:

Equation 2-49:

X100

x

x

y

23,76x

y

4

z

2

For H2NG, the formula is:

Equation 2-50:

X65,4A4,922A195,84

For hydrogen, the dilution factor is calculated as follows:

Equation 2-51:

DiF

X

CH2OCH2ODACH2104

For the reference fuels contained in Appendix x, the values of ‘X’ are as follows:

Fuel | X

Petrol (E5) | 13,4

Diesel (B5) | 13,5

LPG | 11,9

NG/biomethane | 9,5

Ethanol (E85) | 12,5

Hydrogen | 35,03

In these equations:

CCO2concentration of CO2 in the diluted exhaust gas contained in the sampling bag, expressed in percent by volume,

CHCconcentration of HC in the diluted exhaust gas contained in the sampling bag, expressed in ppm carbon equivalent,

CCOconcentration of CO in the diluted exhaust gas contained in the sampling bag, expressed in ppm,

CH2Oconcentration of H2O in the diluted exhaust gas contained in the sampling bag, expressed in percent by volume,

CH2ODAconcentration of H2O in the air used for dilution, expressed in percent by volume,

CH2concentration of hydrogen in the diluted exhaust gas contained in the sampling bag, expressed in ppm,

Aquantity of NG/biomethane in the H2NG mixture, expressed in percent by volume.’;

(c)

in point 6.1.1.5.1.1., ‘Weighting of results from UNECE regulation No 40 and regulation No 47 test cycles’ is replaced by ‘Weighting of results from ECE R40 and ECE R47 test cycles’;

(d)

in Appendix 1, in Table Ap 1-1, the row relating to symbol ‘DF’ is replaced by the following:

‘DiF | Dilution factor | —’

(e)

in Appendix 2, in point 1.1., the second sentence is replaced by the following:

‘The fuel specifications in this Appendix are consistent with the reference fuel specifications in Annex 10 to UNECE regulation No 83 Revision 4 [OJ L 42, 12.2.2014, p. 1.’;].

(f)

In Appendix 11, point 3.2.1.3. is replaced by the following:

‘3.2.1.3. The operating mode switch shall be positioned in accordance with the table Ap11-2.

[For instance: sport, economic, urban, extra-urban position, etc.] [Most electric hybrid mode: the hybrid mode which can be proven to have the highest electricity consumption of all selectable hybrid modes when tested in accordance with condition A of point 4 of Annex 10 to UNECE Regulation No 101, to be established based on information provided by the manufacturer and in agreement with the technical service.] [Most fuel-consuming mode: the hybrid mode which can be proven to have the highest fuel consumption of all selectable hybrid modes when tested in accordance with condition B of point 4 of Annex 10 to UNECE regulation No 101, to be established based on information provided by the manufacturer and in agreement with the technical service.’]

Hybrid-modes -› |

Pure electric

Hybrid

Pure fuel-consuming

Hybrid

Pure electric

Pure fuel-consuming

Hybrid

Hybrid mode n

Hybrid mode m

Battery state of charge | | Switch in position | Switch in position | Switch in position | Switch in position

Condition A

Fully charged

Hybrid | Hybrid | Hybrid | Most electric hybrid mode

Condition B

Min. state of charge

Hybrid | Fuel-consuming | Fuel-consuming | Most fuel-consuming mode

(2)

Annex V is amended as follows:

(a)

Appendix 2 is amended as follows:

(i)

in point 1.1., the following sentence is added:

‘In order to satisfy the evaporative emission test requirements set out in Regulation (EU) No 168/2013, only L-vehicle (sub-)categories L3e, L4e, L5e-A, L6e-A and L7e-A shall be tested.’;

(ii)

in point 4.4., ‘301,2 ± 2 K (28 ± 5 °C)’ is replaced by ‘301,2 ± 5 K (28 ± 5 °C)’;

(b)

Appendix 3 is amended as follows:

(i)

in point 4.4.1., the first sentence is replaced by the following:

‘The fuel tank heating system shall consist of at least two separate heat sources with two temperature controllers.’;

(ii)

in point 4.7.2., ‘Appendix 1’ is replaced by ‘Appendix 4’;

(iii)

point 5.2.3. is replaced by the following:

‘5.2.3. The vehicle is parked in the test area for the minimum period stated in Table Ap3-1.

Engine capacity | Minimum (hours) | Maximum (hours)

< 170 cm3 | 6 | 36

170 cm3 ≤ engine capacity < 280 cm3 | 8 | 36

≥ 280 cm3 | 12 | 36’

(iv)

points 5.3.1.5. and 5.3.1.6. are replaced by the following:

‘5.3.1.5. The fuel and vapour may be artificially heated to the starting temperatures of 288,7 K (15,5 °C) and 294,2 K (21,0 °C) ± 1 K respectively. An initial vapour temperature up to 5 °C above 21,0 °C may be used. For this condition, the vapour shall not be heated at the beginning of the diurnal test. When the fuel temperature has been raised to 5,5 °C below the vapour temperature by following the Tf function, the remainder of the vapour heating profile shall be followed.

5.3.1.6. As soon as the fuel temperature reaches 14,0 °C:

(1)

Install the fuel filler cap(s);

(2)

Turn off the purge blowers, if not already off at that time;

(3)

Close and seal enclosure doors.

As soon as the fuel reaches a temperature of 15,5 °C ± 1 °C the test procedure shall continue as follows:

(a)

the hydrocarbon concentration, barometric pressure and the temperature shall be measured to give the initial readings CHC, i, pi and Ti for the tank heat build test;

(b)

a linear heat build of 13,8 °C or 20 °C ± 0,5 °C over a period of 60 ± 2 minutes shall begin. The temperature of the fuel and fuel vapour during the heating shall conform to the function below to within ± 1,7 °C, or the closest possible function as described in 4.4:

For exposed type of fuel storage tanks:

Equations B.3.3-1

Tf = 0,3333 · t + 15,5 °C

Tv = 0,3333 · t + 21,0 °C

For non-exposed type of fuel storage tanks:

Equations B.3.3-2

Tf = 0,2222 · t + 15,5 °C

Tv = 0,2222 · t + 21,0 °C

where:

Tfrequired temperature of fuel (°C);

Tvrequired temperature of vapour (°C);

ttime from start of the tank heat build in minutes.’;

(c)

Appendix 3.2 is amended as follows:

(i)

point 2 is replaced by the following:

A carbon canister representative of the propulsion family of the vehicle as set out in Annex XI shall be selected as test canister and shall be marked in agreement with the approval authority and the technical service.’;

(ii)

point 3.1 is replaced by the following:

‘3.1 The durability test shall actuate control valves, cables, and linkages, where applicable, and be representative for the operation conditions of these parts during the useful life of the vehicle if used under normal conditions and serviced in accordance with the manufacturer's recommendations. The accumulated distance and operation conditions of the type V durability test may be regarded as representative for the useful life of the vehicle.’;

(3)

Annex VI is amended as follows:

(a)

point 3.1.2 is replaced by the following:

‘3.1.2. Multiple type I emission tests shall be conducted during the full distance accumulation phase with a frequency and amount of type I test procedures at the choice of the manufacturer and to the satisfaction of the technical service and approval authority. The type I emission test results shall provide sufficient statistical relevance to identify the deterioration trend, which shall be representative of the vehicle type with regard to environmental performance as placed on the market (see Figure 5-1).

’

(b)

point 3.2.2 is replaced by the following:

‘3.2.2. Multiple type I emission tests shall be conducted during the partial distance accumulation phase, with the frequency and number of type I test procedures chosen by the manufacturer. The type I emission test results shall provide sufficient statistical relevance to identify the deterioration trend, which shall be representative of the vehicle type with regard to the environmental performance placed on the market (see Figure 5-2).

’

(c)

Appendix 1 is amended as follows:

(i)

point 2.6 is replaced by the following:

2.6.1. For the purpose of accumulating distance in the SRC-LeCV, the L-vehicle categories shall be grouped in accordance with Table Ap1-1.

Cycle | WMTC Class |

1) Vehicle maximum design speed (km/h)

2) Maximum net or continuous rated power (kW)

1 | 1 | vmax ≤ 50 km/h | ≤ 6 kW

2 | 50 km/h < vmax < 100 km/h | < 14 kW

3 | 2 | 100 km/h ≤ vmax < 130 km/h | ≥ 14 kW

4 | 3 | 130 km/h ≤ vmax | —

where:

Vdengine displacement volume in cm3

vmaxmaximum design vehicle speed in km/h

2.6.2. The application of the vehicle classification criteria in Table Ap1-1 shall be performed by applying the following classification criteria hierarchy:

(1)

Maximum design vehicle speed (km/h);

(2)

maximum net or continuous rated power (kW).

2.6.3. If

(a)

the acceleration capability of the L-category vehicle is not sufficient to carry out the acceleration phases within the prescribed distances; or

(b)

the prescribed maximum vehicle speed in the individual cycles cannot be achieved owing to a lack of propulsion power; or

(c)

the maximum design vehicle speed is restricted to a vehicle speed lower than the prescribed SRC-LeCV vehicle speed

the vehicle shall be driven with the accelerator device fully open until the vehicle speed prescribed for the test cycle is reached or until the limited maximum design vehicle speed is reached. Subsequently the test cycle shall be carried out as prescribed for the vehicle category. Significant or frequent deviations from the prescribed vehicle speed tolerance band and the associated justification shall be reported to the approval authority and be included in the type V test report.’;

(ii)

point 2.7.3.4. is replaced by the following:

‘2.7.3.4. coast-through deceleration: full let-off of the throttle, clutch engaged and in gear, no foot/hand control actuated, no brakes applied. If the target speed is 0 km/h (idle) and if the actual vehicle speed is ≤ 5 km/h, the clutch may be disengaged, the gear shifted to neutral and the brakes used in order to prevent engine stall and to entirely stop the vehicle. An upshift is not allowed during a coast-through deceleration. The rider may downshift to increase the braking effect of the engine. During gear changes, extra care shall be afforded to ensure that the gear change is performed promptly, with minimum (i.e. < 2 seconds) coasting in neutral gear, clutch and partial clutch use. The vehicle manufacturer may request to extend this time with the agreement of the approval authority if absolutely necessary.’;

(4)

Annex VII is amended as follows:

(a)

the title is replaced by the following:

(b)

in Appendix 1, points 1.4.3.1. and 1.4.3.2. are replaced by the following:

‘1.4.3.1. for vehicles with a positive ignition engine fuelled with petrol (E5):

Equation Ap1-1:

FC = (0,118/D) · ((0,848 · HC) + (0,429 · CO) + (0,273 · CO2))

where HC, CO and CO2 tailpipe emissions in g/km.

1.4.3.2. for vehicles with a positive ignition engine fuelled with LPG:

Equation Ap1-2:

FCnorm = (0,1212/0,538) · ((0,825 · HC) + (0,429 · CO) + (0,273 · CO2))

where HC, CO and CO2 tailpipe emissions in g/km.

If the composition of the fuel used for the test differs from that assumed for the calculation of normalised consumption, a correction factor (cf) may be applied at the manufacturer's request, as follows:

Equation Ap1-3:

FCnorm = (0,1212/0,538) · (cf) · ((0,825 · HC) + (0,429 · CO) + (0,273 · CO2))

where HC, CO and CO2 tailpipe emissions in g/km.

The correction factor is determined as follows:

Equation Ap1-4:

cf = 0,825 + 0,0693 · nactual;

where:

nactualthe actual H/C ratio of the fuel used;’;

(c)

Appendix 3 is amended as follows:

(i)

point 3.4.1. is replaced by the following:

‘3.4.1. The CO2 values shall be:

Equation Ap3-5:

M1 = m1/Dtest1 (g/km) and

Equation Ap3-6:

M2 = m2/Dtest2 (g/km)

where

Dtest1 and Dtest2the actual distances driven in the tests performed under Conditions A (point 3.2.) and B (point 3.3.) respectively, and

m1 and m2test results determined in points 3.2.3.5. and 3.3.2.5. respectively.’;

(ii)

point 4.4.1. is replaced by the following:

‘The CO2 values shall be:

Equation Ap3-20:

M1 = m1/Dtest1 (g/km) and

Equation Ap3-21:

M2 = m2/Dtest2 (g/km)

where:

Dtest1 and Dtest2the actual distances driven in the tests performed under Conditions A (point 4.2.) and B (point 4.3.) respectively, and

m1 and m2test results determined in points 4.2.4.5. and 4.3.2.5. respectively.’;

(d)

in Appendix 3.3., point 1 is replaced by the following:

1.1. The following test method set out in point 4 shall be used to measure the electric range, expressed in km, of vehicles powered by an electric power train only or the electric range and OVC range of vehicles powered by a hybrid electric powertrain with off-vehicle charging (OVC HEV) as defined in Appendix 3.

1.2. Category L1e vehicles designed to pedal referred to in Annex I to Regulation (EU) No 168/2013 and in point 1.1.2. of Annex XIX to Regulation (EU) No 3/2014 shall be exempted from the electric range test.’;

(5)

Annex IX is amended as follows:

(a)

the following points 2.3. to 2.4.3. are inserted:

2.3.1. L-category vehicles equipped with a manually or electronically controlled, multiple mode, adjustable exhaust silencer system shall be tested in all modes.

2.3.2 For vehicles equipped with a noise abatement system as referred to in point 2.9.1. the reported sound pressure level shall be for the mode having the highest average sound pressure level.

This article is long: the rest is at the official publication.