2 ‘ANNEX I, Regulation (EU) 2016/1375

In force

[Item codes marked with a “TLB” refer to items listed in Annex B of the NSG Part 1 Trigger List. Item codes marked with “TLA” refer to items listed in Annex A of NSG Part 1 Trigger List. Item codes marked with neither “TLB” nor “TLA” refer to items listed in the NSG Dual Use List, referenced in the Categories 1, 2 and 6.]

The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.12/Part 1

0A001 | “Nuclear reactors” and specially designed or prepared equipment and components therefor, as follows: | TLB1.1 | Complete nuclear reactors

0A001.a | “Nuclear reactors”; | TLB1.1 |

Nuclear reactors capable of operation so as to maintain a controlled self-sustaining fission chain reaction.

EXPLANATORY NOTE A “nuclear reactor” basically includes the items within or attached directly to the reactor vessel, the equipment which controls the level of power in the core, and the components which normally contain or come in direct contact with or control the primary coolant of the reactor core. EXPORTS The export of the whole set of major items within this boundary will take place only in accordance with the procedures of the Guidelines. Those individual items within this functionally defined boundary which will be exported only in accordance with the procedures of the Guidelines are listed in paragraphs 1.2. to 1.11. The Government reserves to itself the right to apply the procedures of the Guidelines to other items within the functionally defined boundary

0A001.b | Metal vessels, or major shop-fabricated parts therefor, including the reactor vessel head for a reactor pressure vessel, specially designed or prepared to contain the core of a “nuclear reactor”; | TLB1.2 |

Metal vessels, or major shop-fabricated parts therefor, especially designed or prepared to contain the core of a nuclear reactor as defined in paragraph 1.1. above, as well as relevant reactor internals as defined in paragraph 1.8. below.

EXPLANATORY NOTE Item 1.2 covers nuclear reactor vessels regardless of pressure rating and includes reactor pressure vessels and calandrias. The reactor vessel head is covered by item 1.2. as a major shop-fabricated part of a reactor vessel.

0A001.c | Manipulative equipment specially designed or prepared for inserting or removing fuel in a “nuclear reactor”; | TLB1.3 |

Manipulative equipment especially designed or prepared for inserting or removing fuel in a nuclear reactor as defined in paragraph 1.1. above.

EXPLANATORY NOTE The items noted above are capable of on-load operation or at employing technically sophisticated positioning or alignment features to allow complex off-load fueling operations such as those in which direct viewing of or access to the fuel is not normally available.

0A001.d | Control rods specially designed or prepared for the control of the fission process in a “nuclear reactor”, support or suspension structures therefor, rod drive mechanisms and rod guide tubes; | TLB1.4 |

Especially designed or prepared rods, support or suspension structures therefor, rod drive mechanisms or rod guide tubes to control the fission process in a nuclear reactor as defined in paragraph 1.1. above.

0A001.e | Pressure tubes specially designed or prepared to contain both fuel elements and the primary coolant in a “nuclear reactor”; | TLB1.5 |

Tubes which are especially designed or prepared to contain both fuel elements and the primary coolant in a reactor as defined in paragraph 1.1. above.

EXPLANATORY NOTE Pressure tubes are parts of fuel channels designed to operate at elevated pressure, sometimes in excess of 5 MPa.

0A001.f |

Zirconium metal tubes or zirconium alloy tubes (or assembles of tubes) specially designed or prepared for use as fuel cladding in a “nuclear reactor”, and in quantities exceeding 10 kg;

N.B.: For zirconium pressure tubes see 0A001.e. and for calandria tubes see 0A001.h.

TLB1.6 |

Zirconium metal tubes or zirconium alloy tubes (or assemblies of tubes) especially designed or prepared for use as fuel cladding in a reactor as defined in paragraph 1.1. above, and in quantities exceeding 10 kg.

N.B.: For zirconium pressure tubes see 1.5. For calandria tubes see 1.8.

EXPLANATORY NOTE Zirconium metal tubes or zirconium alloy tubes for use in a nuclear reactor consist of zirconium in which the relation of hafnium to zirconium is typically less than 1:500 parts by weight

0A001.g | Coolant pumps or circulators specially designed or prepared for circulating the primary coolant of “nuclear reactors”; | TLB1.7 |

Pumps or circulators especially designed or prepared for circulating the primary coolant for nuclear reactors as defined in paragraph 1.1. above.

EXPLANATORY NOTE: Especially designed or prepared pumps or circulators include pumps for water-cooled reactors, circulators for gas-cooled reactors, and electromagnetic and mechanical pumps for liquid-metal-cooled reactors. This equipment may include pumps with elaborate sealed or multi-sealed systems to prevent leakage of primary coolant, canned-driven pumps, and pumps with inertial mass systems. This definition encompasses pumps certified to Section III, Division I, Subsection NB (Class 1 components) of the American Society of Mechanical Engineers (ASME) Code, or equivalent standards.

0A001.h |

‘Nuclear reactor internals’ specially designed or prepared for use in a “nuclear reactor”, including support columns for the core, fuel channels, calandria tubes, thermal shields, baffles, core grid plates, and diffuser plates;

In 0A001.h. ‘nuclear reactor internals’ means any major structure within a reactor vessel which has one or more functions such as supporting the core, maintaining fuel alignment, directing primary coolant flow, providing radiation shields for the reactor vessel, and guiding in-core instrumentation.

TLB1.8 |

“Nuclear reactor internals” especially designed or prepared for use in a nuclear reactor as defined in paragraph 1.1 above. This includes, for example, support columns for the core, fuel channels, calandria tubes, thermal shields, baffles, core grid plates, and diffuser plates.

EXPLANATORY NOTE “Nuclear reactor internals” are major structures within a reactor vessel which have one or more functions such as supporting the core, maintaining fuel alignment, directing primary coolant flow, providing radiation shields for the reactor vessel, and guiding in-core instrumentation.

0A001.i |

Heat exchangers as follows:

1.

Steam generators specially designed or prepared for the primary, or intermediate, coolant circuit of a “nuclear reactor”;

2.

Other heat exchangers specially designed or prepared for use in the primary coolant circuit of a “nuclear reactor”;

Note: 0A001.i. does not control heat exchangers for the supporting systems of the reactor, e.g., the emergency cooling system or the decay heat cooling system.

TLB1.9 |

(a)

Steam generators especially designed or prepared for the primary, or intermediate, coolant circuit of a nuclear reactor as defined in paragraph 1.1 above. (b) Other heat exchangers especially designed or prepared for use in the primary coolant circuit of a nuclear reactor as defined in paragraph 1.1 above.

EXPLANATORY NOTE Steam generators are especially designed or prepared to transfer the heat generated in the reactor to the feed water for steam generation. In the case of a fast reactor for which an intermediate coolant loop is also present, the steam generator is in the intermediate circuit. In a gas-cooled reactor, a heat exchanger may be utilized to transfer heat to a secondary gas loop that drives a gas turbine. The scope of control for this entry does not include heat exchangers for the supporting systems of the reactor, e.g., the emergency cooling system or the decay heat cooling system.

0A001.j | Neutron detectors specially designed or prepared for determining neutron flux levels within the core of a “nuclear reactor”; | TLB1.10 |

Especially designed or prepared neutron detectors for determining neutron flux levels within the core of a reactor as defined in paragraph 1.1. above.

EXPLANATORY NOTE The scope of this entry encompasses in-core and ex-core detectors which measure flux levels in a large range, typically from 104 neutrons per cm2 per second to 1010 neutrons per cm2 per second or more. Ex-core refers to those instruments outside the core of a reactor as defined in paragraph 1.1. above, but located within the biological shielding.

0A001.k |

‘External thermal shields’ specially designed or prepared for use in a “nuclear reactor” for the reduction of heat loss and also for the containment vessel protection.

In 0A001.k. ‘external thermal shields’ means major structures placed over the reactor vessel which reduce heat loss from the reactor and reduce temperature within the containment vessel.

TLB1.11 |

“External thermal shields” especially designed or prepared for use in a nuclear reactor as defined in paragraph 1.1 for reduction of heat loss and also for containment vessel protection.

EXPLANATORY NOTE “External thermal shields” are major structures placed over the reactor vessel which reduce heat loss from the reactor and reduce temperature within the containment vessel.

0B001 | Plant for the separation of isotopes of “natural uranium”, “depleted uranium” or “special fissile materials”, and specially designed or prepared equipment and components therefor, as follows: | TLB5 | Plants for the separation of isotopes of natural uranium, depleted uranium or special fissionable material and equipment, other than analytical instruments, especially designed or prepared therefor

0B001.a |

Plant specially designed for separating isotopes of “natural uranium”, “depleted uranium”, or “special fissile materials”, as follows:

1.

Gas centrifuge separation plant;

2.

Gaseous diffusion separation plant;

3.

Aerodynamic separation plant;

4.

Chemical exchange separation plant;

5.

Ion-exchange separation plant;

6.

Atomic vapour “laser” isotope separation plant;

7.

Molecular “laser” isotope separation plant;

8.

Plasma separation plant;

9.

Electro magnetic separation plant;

TLB5 |

0B001.b |

Gas centrifuges and assemblies and components, specially designed or prepared for gas centrifuge separation process, as follows:

In 0B001.b. ‘high strength-to-density ratio material’ means any of the following:

1.

Maraging steel capable of an ultimate tensile strength of 1,95 GPa or more;

2.

Aluminium alloys capable of an ultimate tensile strength of 0,46 GPa or more; or

3.

“Fibrous or filamentary materials” with a “specific modulus” of more than 3,18 × 106 m and a “specific tensile strength” greater than 7,62 × 104 m;

1.

Gas centrifuges;

TLB5.1 |

The gas centrifuge normally consists of a thin-walled cylinder(s) of between 75 mm and 650 mm diameter contained in a vacuum environment and spun at high peripheral speed of the order of 300 m/s or more with its central axis vertical. In order to achieve high speed the materials of construction for the rotating components have to be of a high strength to density ratio and the rotor assembly, and hence its individual components, have to be manufactured to very close tolerances in order to minimize the unbalance. In contrast to other centrifuges, the gas centrifuge for uranium enrichment is characterized by having within the rotor chamber a rotating disc-shaped baffle(s) and a stationary tube arrangement for feeding and extracting the UF6 gas and featuring at least three separate channels, of which two are connected to scoops extending from the rotor axis towards the periphery of the rotor chamber. Also contained within the vacuum environment are a number of critical items which do not rotate and which although they are especially designed are not difficult to fabricate nor are they fabricated out of unique materials. A centrifuge facility however requires a large number of these components, so that quantities can provide an important indication of end use.

0B001.b | | TLB5.1.1 | Rotating components

0B001.b. |

2.

Complete rotor assemblies;

TLB5.1.1a |

(a)

Complete rotor assemblies:

Thin-walled cylinders, or a number of interconnected thin-walled cylinders, manufactured from one or more of the high strength to density ratio materials described in the EXPLANATORY NOTE to this Section. If interconnected, the cylinders are joined together by flexible bellows or rings as described in section 5.1.1.(c) following. The rotor is fitted with an internal baffle(s) and end caps, as described in section 5.1.1.(d) and (e) following, if in final form. However the complete assembly may be delivered only partly assembled.

0B001.b. |

3.

Rotor tube cylinders with a wall thickness of 12 mm or less, a diameter of between 75 mm and 650 mm, made from ‘high strength-to-density ratio materials’;

TLB5.1.1b |

(b)

Rotor tubes:

Especially designed or prepared thin-walled cylinders with thickness of 12 mm or less, a diameter of between 75 mm and 650 mm, and manufactured from one or more of the high strength to density ratio materials described in the EXPLANATORY NOTE to this Section.

0B001.b. |

4.

Rings or bellows with a wall thickness of 3 mm or less and a diameter of between 75 mm and 650 mm and designed to give local support to a rotor tube or to join a number together, made from ‘high strength-to-density ratio materials’;

TLB5.1.1c |

(c)

Rings or Bellows:

Components especially designed or prepared to give localized support to the rotor tube or to join together a number of rotor tubes. The bellows is a short cylinder of wall thickness 3 mm or less, a diameter of between 75 mm and 650 mm, having a convolute, and manufactured from one of the high strength to density ratio materials described in the EXPLANATORY NOTE to this Section.

0B001.b. |

5.

Baffles of between 75 mm and 650 mm diameter for mounting inside a rotor tube, made from ‘high strength-to-density ratio materials’.

TLB5.1.1d |

(d)

Baffles:

Disc-shaped components of between 75 mm and 650 mm diameter especially designed or prepared to be mounted inside the centrifuge rotor tube, in order to isolate the take-off chamber from the main separation chamber and, in some cases, to assist the UF6 gas circulation within the main separation chamber of the rotor tube, and manufactured from one of the high strength to density ratio materials described in the EXPLANATORY NOTE to this Section.

0B001.b. |

6.

Top or bottom caps of between 75 mm and 650 mm diameter to fit the ends of a rotor tube, made from ‘high strength-to-density ratio materials’;

TLB5.1.1e |

(e)

Top caps/Bottom caps:

Disc-shaped components of between 75 mm and 650 mm diameter especially designed or prepared to fit to the ends of the rotor tube, and so contain the UF6 within the rotor tube, and in some cases to support, retain or contain as an integrated part an element of the upper bearing (top cap) or to carry the rotating elements of the motor and lower bearing (bottom cap), and manufactured from one of the high strength to density ratio materials described in the EXPLANATORY NOTE to this Section.

TLB5.1.1 |

The materials used for centrifuge rotating components include the following:

(a)

Maraging steel capable of an ultimate tensile strength of 1,95 GPa or more;

(b)

Aluminium alloys capable of an ultimate tensile strength of 0,46 GPa or more;

(c)

Filamentary materials suitable for use in composite structures and having a specific modulus of 3,18 × 106 m or greater and a specific ultimate tensile strength of 7,62 × 104 m or greater (‘Specific Modulus’ is the Young's Modulus in N/m2 divided by the specific weight in N/m3; ‘Specific Ultimate Tensile Strength’ is the ultimate tensile strength in N/m2 divided by the specific weight in N/m3).

0B001.b | | TLB5.1.2 | Static components

0B001.b. |

7.

Magnetic suspension bearings as follows:

a.

Bearing assemblies consisting of an annular magnet suspended within a housing made of or protected by “materials resistant to corrosion by UF6” containing a damping medium and having the magnet coupling with a pole piece or second magnet fitted to the top cap of the rotor;

b.

Active magnetic bearings specially designed or prepared for use with gas centrifuges.

TLB5.1.2A.1 |

(a)

Magnetic suspension bearings:

1.

Especially designed or prepared bearing assemblies consisting of an annular magnet suspended within a housing containing a damping medium. The housing will be manufactured from a UF6-resistant material (see EXPLANATORY NOTE to Section 5.2.). The magnet couples with a pole piece or a second magnet fitted to the top cap described in Section 5.1.1.(e).

The magnet may be ring-shaped with a relation between outer and inner diameter smaller or equal to 1,6:1. The magnet may be in a form having an initial permeability of 0,15 H/m or more, or a remanence of 98,5 % or more, or an energy product of greater than 80 kJ/m3. In addition to the usual material properties, it is a prerequisite that the deviation of the magnetic axes from the geometrical axes is limited to very small tolerances (lower than 0,1 mm) or that homogeneity of the material of the magnet is specially called for.

0B001.b. | | TLB5.1.2a2 |

2.

Active magnetic bearings especially designed or prepared for use with gas centrifuges.

These bearings usually have the following characteristics:

Designed to keep centred a rotor spinning at 600 Hz or more, and

Associated to a reliable electrical power supply and/or to an uninterruptible power supply (UPS) unit in order to function for more than one hour.

0B001.b. |

8.

Specially prepared bearings comprising a pivot-cup assembly mounted on a damper;

TLB5.1.2b |

(b)

Bearings/Dampers:

Especially designed or prepared bearings comprising a pivot/cup assembly mounted on a damper. The pivot is normally a hardened steel shaft with a hemisphere at one end with a means of attachment to the bottom cap described in section 5.1.1.(e) at the other. The shaft may however have a hydrodynamic bearing attached. The cup is pellet-shaped with a hemispherical indentation in one surface.

These components are often supplied separately to the damper.

0B001.b. |

9.

Molecular pumps comprised of cylinders having internally machined or extruded helical grooves and internally machined bores;

TLB5.1.2c |

(c)

Molecular pumps:

Especially designed or prepared cylinders having internally machined or extruded helical grooves and internally machined bores. Typical dimensions are as follows:

75 mm to 650 mm internal diameter, 10 mm or more wall thickness, with the length equal to or greater than the diameter. The grooves are typically rectangular in cross-section and 2 mm or more in depth.

0B001.b. |

10.

Ring-shaped motor stators for multiphase AC hysteresis (or reluctance) motors for synchronous operation within a vacuum at a frequency of 600 Hz or more and a power of 40 VA or more;

TLB5.1.2d |

(d)

Motor stators:

Especially designed or prepared ring-shaped stators for high speed multiphase AC hysteresis (or reluctance) motors for synchronous operation within a vacuum at a frequency of 600 Hz or greater and a power of 40 VA or greater. The stators may consist of multi-phase windings on a laminated low loss iron core comprised of thin layers typically 2,0 mm thick or less.

0B001.b. |

11.

Centrifuge housing/recipients to contain the rotor tube assembly of a gas centrifuge, consisting of a rigid cylinder of wall thickness up to 30 mm with precision machined ends that are parallel to each other and perpendicular to the cylinder's longitudinal axis to within 0,05 degrees or less;

TLB5.1.2e |

(e)

Centrifuge housing/recipients:

Components especially designed or prepared to contain the rotor tube assembly of a gas centrifuge. The housing consists of a rigid cylinder of wall thickness up to 30 mm with precision machined ends to locate the bearings and with one or more flanges for mounting. The machined ends are parallel to each other and perpendicular to the cylinder's longitudinal axis to within 0,05 degrees or less. The housing may also be a honeycomb type structure to accommodate several rotor assemblies.

0B001.b. |

12.

Scoops consisting of specially designed or prepared tubes for the extraction of UF6 gas from within the rotor tube by a Pitot tube action and capable of being fixed to the central gas extraction system;

TLB5.1.2f |

(f)

Scoops:

Especially designed or prepared tubes for the extraction of UF6 gas from within the rotor tube by a Pitot tube action (that is, with an aperture facing into the circumferential gas flow within the rotor tube, for example by bending the end of a radially disposed tube) and capable of being fixed to the central gas extraction system.

0B001.b. |

13.

Frequency changers (converters or inverters) specially designed or prepared to supply motor stators for gas centrifuge enrichment, having all of the following characteristics, and specially designed components therefor:

a.

A multiphase frequency output of 600 Hz or greater; and

b.

High stability (with frequency control better than 0,2 %);

TLB5.2.5 |

Frequency changers (also known as converters or inverters) especially designed or prepared to supply motor stators as defined under 5.1.2.(d), or parts, components and sub-assemblies of such frequency changers having all of the following characteristics:

1.

A multiphase frequency output of 600 Hz or greater; and

2.

High stability (with frequency control better than 0,2 %).

0B001.b. |

14.

Shut-off and control valves as follows:

a.

Shut-off valves specially designed or prepared to act on the feed, product or tails UF6 gaseous streams of an individual gas centrifuge;

b.

Bellows-sealed valves, shut-off or control, made of or protected by “materials resistant to corrosion by UF6”, with an inside diameter of 10 mm to 160 mm, specially designed or prepared for use in main or auxiliary systems of gas centrifuge enrichment plants;

TLB5.2.3 |

(a)

Shut-off valves especially designed or prepared to act on the feed, product or tails UF6 gaseous streams of an individual gas centrifuge.

(b)

Bellows-sealed valves, manual or automated, shut-off or control, made of or protected by materials resistant to corrosion by UF6, with an inside diameter of 10 to 160 mm, especially designed or prepared for use in main or auxiliary systems of gas centrifuge enrichment plants.

Typical especially designed or prepared valves include bellow-sealed valves, fast acting closure-types, fast acting valves and others.

0B001.c |

1.

Gaseous diffusion barriers made of porous metallic, polymer or ceramic “materials resistant to corrosion by UF6” with a pore size of 10 to 100 nm, a thickness of 5 mm or less, and, for tubular forms, a diameter of 25 mm or less;

TLB5.3.1a |

This article is long: the rest is at the official publication.