ANNEX I, Regulation (EU) 2016/918

In forcesince 19 May 2016

Annex I to Regulation (EC) No 1272/2008 is amended as follows:

A. Part 1 is amended as follows:

(1)

The title of Section 1.1.3.4 is replaced by the following:

(2)

Section 1.3.6 is replaced by the following:

Substances or mixtures classified as corrosive to metals but not classified as skin corrosion or as serious eye damage (Category 1) which are in the finished state and packaged for consumer use do not require on the label the hazard pictogram GHS05.’

B. Part 2 is amended as follows:

(1)

Section 2.1.3 is replaced by the following:

Label elements shall be used for substances, mixtures or articles meeting the criteria for classification in this hazard class in accordance with Table 2.1.2.

Classification | Unstable Explosive | Division 1.1 | Division 1.2 | Division 1.3 | Division 1.4 | Division 1.5 | Division 1.6

GHS Pictograms | | | | | | |

Signal Word | Danger | Danger | Danger | Danger | Warning | Danger | No signal word

Hazard Statement | H200: Unstable Explosive | H201: Explosive; mass explosion hazard | H202: Explosive; severe projection hazard | H203: Explosive; fire, blast or projection hazard | H204: Fire or projection hazard | H205: May mass explode in fire | No hazard statement

Precautionary Statement Prevention |

P201

P250

P280

P210

P230

P234

P240

P250

P280

P210

P230

P234

P240

P250

P280

P210

P230

P234

P240

P250

P280

P210

P234

P240

P250

P280

P210

P230

P234

P240

P250

P280

No precautionary statement

Precautionary Statement Response | P370 + P372 + P380 + P373 | P370 + P372 + P380 + P373 | P370 + P372 + P380 + P373 | P370 + P372 + P380 + P373 |

P370 + P372 + P380 + P373

P370 + P380 + P375

P370 + P372 + P380 + P373 | No precautionary statement

Precautionary Statement Storage | P401 | P401 | P401 | P401 | P401 | P401 | No precautionary statement

Precautionary Statement Disposal | P501 | P501 | P501 | P501 | P501 | P501 | No precautionary statement

NOTE 1: Unpackaged explosives or explosives repackaged in packaging other than the original or similar packaging shall include all of the following label elements:

(a)

the pictogram: exploding bomb;

(b)

the signal word “Danger”; and

(c)

the hazard statement: “Explosive; mass explosion hazard”

unless the hazard is shown to correspond to one of the hazard categories in Table 2.1.2, in which case the corresponding symbol, the signal word and/or the hazard statement shall be assigned.

NOTE 2: Substances and mixtures, as supplied, with a positive result in Test Series 2 in Part I, Section 12, of the UN RTDG, Manual of Tests and Criteria, which are exempted from classification as explosives (based on a negative result in Test Series 6 in Part I, Section 16 of the UN RTDG, Manual of Tests and Criteria) still have explosive properties. The user shall be informed of these intrinsic explosive properties because they have to be considered for handling — especially if the substance or mixture is removed from its packaging or is repackaged — and for storage. For this reason, the explosive properties of the substance or mixture shall be communicated in Section 2 (Hazards identification) and Section 9 (Physical and chemical properties) of the Safety Data Sheet and other sections of the Safety Data Sheet, as appropriate.’

(2)

In Section 2.1.4, Figure 2.1.3 is replaced by the following:

’

(3)

In Section 2.2.3, Table 2.2.3 is replaced by the following:

Classification | Flammable gas | Chemically unstable gas

Category 1 | Category 2 | Category A | Category B

GHS Pictogram | | No pictogram | No additional pictogram | No additional pictogram

Signal Word | Danger | Warning | No additional signal word | No additional signal word

Hazard Statement | H220: Extremely flammable gas | H221: Flammable gas | Additional hazard statement H230: May react explosively even in the absence of air | Additional hazard statement H231: May react explosively even in the absence of air at elevated pressure and/or temperature

Precautionary Statement Prevention | P210 | P210 | P202 | P202’

Precautionary Statement Response |

P377

P381

P377

P381

Precautionary Statement Storage | P403 | P403 | |

Precautionary Statement Disposal | | | |

(4)

Section 2.3.2.1 is replaced by the following:

‘2.3.2.1.

Aerosols shall be classified in one of the three categories of this hazard class, depending on their flammable properties and their heat of combustion. They shall be considered for classification in Category 1 or 2 if they contain more than 1 % components (by mass) which are classified as flammable according to the following criteria set out in this Part:

Flammable gases (see Section 2.2);

Liquids with a flash point ≤ 93 °C, which includes Flammable Liquids according to Section 2.6;

Flammable solids (see Section 2.7);

or if their heat of combustion is at least 20 kJ/g.

NOTE 1: Flammable components do not cover pyrophoric, self-heating or water-reactive substances and mixtures because such components are never used as aerosol contents.

NOTE 2: Aerosols do not fall additionally within the scope of Sections 2.2 (flammable gases), 2.5 (gases under pressure), 2.6 (flammable liquids) and 2.7 (flammable solids). Depending on their contents, aerosols may however fall within the scope of other hazard classes, including their labelling elements.’

(5)

In Section 2.3.2, Figure 2.3.1(a) is replaced by the following:

’

(6)

In Section 2.3.3, the heading of Table 2.3.1 is replaced by the following:

(7)

In Section 2.5.3, Table 2.5.2 is replaced by the following:

Classification | Compressed gas | Liquefied gas | Refrigerated liquefied gas | Dissolved gas

GHS Pictograms | | | |

Signal Word | Warning | Warning | Warning | Warning

Hazard Statement | H280: Contains gas under pressure; may explode if heated | H280: Contains gas under pressure; may explode if heated | H281: Contains refrigerated gas; may cause cryogenic burns or injury | H280: Contains gas under pressure; may explode if heated

Precautionary Statement Prevention | | | P282 |

Precautionary Statement Response | | | P336 + P315 |

Precautionary Statement Storage | P410 + P403 | P410 + P403 | P403 | P410 + P403’

Precautionary Statement Disposal | | | |

(8)

In Section 2.8.3, Table 2.8.1 is replaced by the following:

[Type G has no hazard communication elements assigned but should be considered for properties belonging to other hazard classes.] [See the introduction to Annex IV for details on the use of square brackets.’]

Classification | Type A | Type B | Type C & D | Type E & F | Type G

GHS Pictograms | | | | | There are no label elements allocated to this hazard category

Signal Word | Danger | Danger | Danger | Warning

Hazard Statement | H240: Heating may cause an explosion | H241: Heating may cause a fire or explosion | H242: Heating may cause a fire | H242: Heating may cause a fire

Precautionary Statement Prevention |

P210

P234

P235

P240

P280

P210

P234

P235

P240

P280

P210

P234

P235

P240

P280

P210

P234

P235

P240

P280

Precautionary Statement Response | P370 + P372 + P380 + P373 | P370 + P380 + P375 [+ P378] | P370 + P378 | P370 + P378 |

Precautionary Statement Storage |

P403

P411

P420

P403

P411

P420

P403

P411

P420

P403

P411

P420

Precautionary Statement Disposal | P501 | P501 | P501 | P501 |

(9)

In Section 2.8.4, Figure 2.8.1 is replaced by the following:

’

(10)

In Section 2.9.3, Table 2.9.2 is replaced by the following:

Classification | Category 1

GHS Pictogram |

Signal Word | Danger

Hazard Statement | H250: Catches fire spontaneously if exposed to air

Precautionary Statement Prevention |

P210

P222

P231 + P232

P233

P280

Precautionary Statement Response |

P302 + P334

P370 + P378’

Precautionary Statement Storage |

Precautionary Statement Disposal |

(11)

In Section 2.10.3, Table 2.10.2 is replaced by the following:

Classification | Category 1

GHS Pictogram |

Signal Word | Danger

Hazard Statement | H250: Catches fire spontaneously if exposed to air

Precautionary Statement Prevention |

P210

P222

P231 + P232

P233

P280

Precautionary Statement Response |

P302 + P335 + P334

P370 +P378’

Precautionary Statement Storage |

Precautionary Statement Disposal |

(12)

In Section 2.11.3, Table 2.11.2 is replaced by the following:

Classification | Category 1 | Category 2

GHS Pictograms | |

Signal Word | Danger | Warning

Hazard Statement | H251: Self-heating; may catch fire | H252: Self-heating in large quantities; may catch fire

Precautionary Statement Prevention |

P235

P280

P235

P280

Precautionary Statement Response | |

Precautionary Statement Storage |

P407

P413

P420

P407

P413

P420’

Precautionary Statement Disposal | |

(13)

In Section 2.12.3, Table 2.12.2 is replaced by the following:

Classification | Category 1 | Category 2 | Category 3

GHS Pictograms | | |

Signal Word | Danger | Danger | Warning

Hazard Statement | H260: In contact with water releases flammable gases which may ignite spontaneously | H261: In contact with water releases flammable gases | H261: In contact with water releases flammable gases

Precautionary Statement Prevention |

P223

P231 + P232

P280

P223

P231 + P232

P280

P231 + P232

P280

Precautionary Statement Response |

P302 + P335 + P334

P370 + P378

P302 + P335 + P334

P370 + P378

P370 + P378

Precautionary Statement Storage | P402 + P404 | P402 + P404 | P402 + P404

Precautionary Statement Disposal | P501 | P501 | P501’

(14)

In Section 2.13.3, Table 2.13.2 is replaced by the following:

Classification | Category 1 | Category 2 | Category 3

GHS Pictograms | | |

Signal Word | Danger | Danger | Warning

Hazard Statement | H271: May cause fire or explosion; strong oxidiser | H272: May intensify fire; oxidiser | H272: May intensify fire; oxidiser

Precautionary Statement Prevention |

P210

P220

P280

P283

P210

P220

P280

P210

P220

P280

Precautionary Statement Response |

P306 + P360

P371 + P380 + P375

P370 + P378

P370 + P378 | P370 + P378

Precautionary Statement Storage | P420 | |

Precautionary Statement Disposal | P501 | P501 | P501’

(15)

In Section 2.14.2.1, the introductory sentence is replaced by the following:

‘An oxidising solid shall be classified in one of the three categories for this class using test O.1 in Part III, sub-section 34.4.1 or test O.3 in Part III, sub-section 34.4 3 of the UN RTDG, Manual of Tests and Criteria in accordance with Table 2.14.1:’

(16)

In Section 2.14.2.1, Table 2.14.1 is replaced by the following:

Category | Criteria using test O.1 | Criteria using test O.3

1 | Any substance or mixture which, in the 4:1 or 1:1 sample-to-cellulose ratio (by mass) tested, exhibits a mean burning time less than the mean burning time of a 3:2 mixture, (by mass), of potassium bromate and cellulose. | Any substance or mixture which, in the 4:1 or 1:1 sample-to-cellulose ratio (by mass) tested, exhibits a mean burning rate greater than the mean burning rate of a 3:1 mixture (by mass) of calcium peroxide and cellulose.

2 | Any substance or mixture which, in the 4:1 or 1:1 sample-to-cellulose ratio (by mass) tested, exhibits a mean burning time equal to or less than the mean burning time of a 2:3 mixture (by mass) of potassium bromate and cellulose and the criteria for Category 1 are not met. | Any substance or mixture which, in the 4:1 or 1:1 sample-to-cellulose ratio (by mass) tested, exhibits a mean burning rate equal to or greater than the mean burning rate of a 1:1 mixture (by mass) of calcium peroxide and cellulose and the criteria for Category 1 are not met.

3 | Any substance or mixture which, in the 4:1 or 1:1 sample-to-cellulose ratio (by mass) tested, exhibits a mean burning time equal to or less than the mean burning time of a 3:7 mixture (by mass) of potassium bromate and cellulose and the criteria for Categories 1 and 2 are not met. | Any substance or mixture which, in the 4:1 or 1:1 sample-to-cellulose ratio (by mass) tested, exhibits a mean burning rate equal to or greater than the mean burning rate of a 1:2 mixture (by mass) of calcium peroxide and cellulose and the criteria for Categories 1 and 2 are not met.’

(17)

In Section 2.14.2.1, in Note 1 to Table 2.14.1, ‘(BC Code, Annex 3, Test 5)’ is replaced by ‘(IMSBC Code (International Maritime Solid Bulk Cargoes Code, IMO), Appendix 2, Section 5)’.

(18)

In Section 2.14.3, Table 2.14.2 is replaced by the following:

Category 1 | Category 2 | Category 3

GHS Pictograms | | |

Signal Word | Danger | Danger | Warning

Hazard Statement | H271: May cause fire or explosion; strong oxidiser | H272: May intensify fire; oxidiser | H272: May intensify fire; oxidiser

Precautionary Statement Prevention |

P210

P220

P280

P283

P210

P220

P280

P210

P220

P280

Precautionary Statement Response |

P306 + P360

P371 + P380 + P375

P370 + P378

P370 + P378 | P370 + P378

Precautionary Statement Storage | P420 | |

Precautionary Statement Disposal | P501 | P501 | P501’

(19)

In Section 2.15.3, Table 2.15.1 is replaced by the following:

[See the introduction to Annex IV for details on the use of square brackets.’]

Classification | Type A | Type B | Type C & D | Type E & F | Type G

GHS Pictograms | | | | | There are no label elements allocated to this hazard category

Signal Word | Danger | Danger | Danger | Warning

Hazard Statement | H240: Heating may cause an explosion | H241: Heating may cause a fire or explosion | H242: Heating may cause a fire | H242: Heating may cause a fire

Precautionary Statement Prevention |

P210

P234

P235

P240

P280

P210

P234

P235

P240

P280

P210

P234

P235

P240

P280

P210

P234

P235

P240

P280

Precautionary Statement Response | P370 + P372 + P380 + P373 | P370 + P380 + P375[+ P378] | P370 + P378 | P370 + P378 |

Precautionary Statement Storage |

P403

P410

P411

P420

P403

P410

P411

P420

P403

P410

P411

P420

P403

P410

P411

P420

Precautionary Statement Disposal | P501 | P501 | P501 | P501 |

(20)

In Section 2.15.4, Figure 2.15.1 is replaced by the following:

’

C. Part 3 is amended as follows:

(1)

In Section 3.1.2.1, the first sentence is replaced by the following:

‘Substances can be allocated to one of four hazard categories based on acute toxicity by the oral, dermal or inhalation route according to the numeric criteria shown in Table 3.1.1.’

(2)

In Section 3.1.2.3.2, the first sentence is replaced by the following:

‘Of particular importance in classifying for inhalation toxicity is the use of well articulated values in the highest hazard categories for dusts and mists.’

(3)

In Section 3.1.3.6.1, point (a) is replaced by the following:

‘include ingredients with a known acute toxicity, which fall into any of the acute hazard categories shown in Table 3.1.1;’

(4)

Chapter 3.2 is replaced by the following:

3.2.1.1.

Skin corrosion means the production of irreversible damage to the skin; namely, visible necrosis through the epidermis and into the dermis, following the application of a test substance for up to 4 hours. Corrosive reactions are typified by ulcers, bleeding, bloody scabs, and, by the end of observation at 14 days, by discolouration due to blanching of the skin, complete areas of alopecia, and scars. Histopathology shall be considered to evaluate questionable lesions.

Skin irritation means the production of reversible damage to the skin following the application of a test substance for up to 4 hours.

3.2.1.2.

In a tiered approach, emphasis shall be placed upon existing human data, followed by existing animal data, followed by in vitro data and then other sources of information. Classification results directly when the data satisfy the criteria. In some cases, classification of a substance or a mixture is made on the basis of the weight of evidence within a tier. In a total weight of evidence approach all available information bearing on the determination of skin corrosion/irritation is considered together, including the results of appropriate validated in vitro tests, relevant animal data, and human data such as epidemiological and clinical studies and well-documented case reports and observations (see Annex I, Part 1, Sections 1.1.1.3, 1.1.1.4 and 1.1.1.5).

Substances shall be allocated to one of the following two categories within this hazard class:

(a)

Category 1 (skin corrosion)

This category is further subdivided in three sub-categories (1A, 1B, 1C). Corrosive substances shall be classified in Category 1 where data is not sufficient for sub-categorisation. When data are sufficient, substances shall be classified in one of the three sub-categories 1A, 1B, or 1C (see Table 3.2.1.)

(b)

Category 2 (skin irritation) (see Table 3.2.2).

3.2.2.1.1.1. A substance is corrosive to skin when it produces destruction of skin tissue, namely, visible necrosis through the epidermis and into the dermis in at least one tested animal after exposure for up to 4 hours.

3.2.2.1.1.2. Corrosive substances shall be classified in Category 1 where data is not sufficient for sub-categorisation.

3.2.2.1.1.3. When data are sufficient substances shall be classified in one of the three sub-categories 1A, 1B, or 1C in accordance with the criteria in Table 3.2.1.

3.2.2.1.1.4. Three sub-categories are provided within the corrosion category: sub-category 1A — where corrosive responses are noted following up to 3 minutes exposure and up to 1 hour observation; sub-category 1B — where corrosive responses are described following exposure greater than 3 minutes and up to 1 hour and observations up to 14 days; and sub-category 1C — where corrosive responses occur after exposures greater than 1 hour and up to 4 hours and observations up to 14 days.

[See the conditions for the use of Category 1 in paragraph (a) of Section 3.2.2.]

Category | Criteria

Category 1 | Destruction of skin tissue, namely, visible necrosis through the epidermis and into the dermis, in at least one tested animal after exposure ≤ 4 h

Sub-Category 1A | Corrosive responses in at least one animal following exposure ≤ 3 min during an observation period ≤ 1 h

Sub-Category 1B | Corrosive responses in at least one animal following exposure > 3 min and ≤ 1 h and observations ≤ 14 days

Sub-Category 1C | Corrosive responses in at least one animal after exposures > 1 h and ≤ 4 h and observations ≤ 14 days

3.2.2.1.1.5. The use of human data is discussed in Sections 3.2.1.2 and 3.2.2.2 and also in Sections 1.1.1.3, 1.1.1.4 and 1.1.1.5.

3.2.2.1.2.1. A substance is irritant to skin when it produces reversible damage to the skin following its application for up to 4 hours. The major criterion for the irritation category is that at least 2 of 3 tested animals have a mean score of ≥ 2,3 and ≤ 4,0.

3.2.2.1.2.2. A single irritation category (Category 2) is presented in Table 3.2.2, using the results of animal testing.

3.2.2.1.2.3. Reversibility of skin lesions is also considered in evaluating irritant responses. When inflammation persists to the end of the observation period in 2 or more test animals, taking into consideration alopecia (limited area), hyperkeratosis, hyperplasia and scaling, then a material shall be considered to be an irritant.

3.2.2.1.2.4. Animal irritant responses within a test can be variable, as they are with corrosion. A separate irritant criterion accommodates cases where there is a significant irritant response but less than the mean score criterion for a positive test. For example, a test material might be designated as an irritant if at least 1 of 3 tested animals shows a very elevated mean score throughout the study, including lesions persisting at the end of an observation period of normally 14 days. Other responses could also fulfil this criterion. However, it should be ascertained that the responses are the result of chemical exposure.

[Grading criteria are understood as described in Regulation (EC) No 440/2008.]

Category | Criteria

Irritation (Category 2) |

(1)

Mean score of ≥ 2,3 and ≤ 4,0 for erythema/eschar or for oedema in at least 2 of 3 tested animals from gradings at 24, 48 and 72 hours after patch removal or, if reactions are delayed, from grades on 3 consecutive days after the onset of skin reactions; or

(2)

Inflammation that persists to the end of the observation period normally 14 days in at least 2 animals, particularly taking into account alopecia (limited area), hyperkeratosis, hyperplasia, and scaling reactions; or

(3)

In some cases where there is pronounced variability of response among animals, with very definite positive effects related to chemical exposure in a single animal but less than the criteria above .

3.2.2.1.2.5. The use of human data is discussed in Sections 3.2.1.2 and 3.2.2.2 and also in Sections 1.1.1.3, 1.1.1.4 and 1.1.1.5.

3.2.2.2.1.

A tiered approach to the evaluation of initial information shall be considered, where applicable, recognising that not all elements may be relevant.

3.2.2.2.2.

Existing human and animal data including information from single or repeated exposure shall be the first line of evaluation, as they give information directly relevant to effects on the skin.

3.2.2.2.3.

Acute dermal toxicity data may be used for classification. If a substance is highly toxic by the dermal route, a skin corrosion/irritation study is not practicable since the amount of test substance to be applied considerably exceeds the toxic dose and, consequently, results in the death of the animals. When observations are made of skin corrosion/irritation in acute toxicity studies and are observed up through the limit dose, these data may be used for classification, provided that the dilutions used and species tested are equivalent. Solid substances (powders) may become corrosive or irritant when moistened or in contact with moist skin or mucous membranes.

3.2.2.2.4.

In vitro alternatives that have been validated and accepted shall be used to make classification decisions.

3.2.2.2.5.

Likewise, pH extremes like ≤ 2 and ≥ 11,5 may indicate the potential to cause skin effects, especially when associated with significant acid/alkaline reserve (buffering capacity). Generally, such substances are expected to produce significant effects on the skin. In the absence of any other information, a substance is considered as corrosive to skin (Skin Corrosion Category 1) if it has a pH ≤ 2 or a pH ≥ 11,5. However, if consideration of acid/alkaline reserve suggests the substance may not be corrosive despite the low or high pH value, this needs to be confirmed by other data, preferably by data from an appropriate validated in vitro test.

3.2.2.2.6.

In some cases, sufficient information may be available from structurally related substances to make classification decisions.

3.2.2.2.7.

The tiered approach provides guidance on how to organize existing information on a substance and to make a weight of evidence decision about hazard assessment and hazard classification.

Although information might be gained from the evaluation of single parameters within a tier (see Section 3.2.2.2.1.), consideration shall be given to the totality of existing information and making an overall weight of evidence determination. This is especially true when there is conflict in information available on some parameters.

3.2.3.1.1.

This article is long: the rest is at the official publication.