1 ANNEX, Decision_act (EU) 2016/1332

In forcesince 18 Jul 2022

Criteria for awarding the EU Ecolabel to furniture products:

1.

Product description

2.

General requirements for hazardous substances and mixtures

3.

Wood, cork, bamboo and rattan

4.

Plastics

5.

Metals

6.

Upholstery covering materials

7.

Upholstery padding materials

8.

Glass: use of heavy metals

9.

Final product requirements

10.

Consumer information

11.

Information appearing on the EU Ecolabel

The specific assessment and verification requirements are indicated within each criterion.

Where the applicant is required to provide declarations, documentation, analyses, test reports, or other evidence to show compliance with the criteria, these may originate from the applicant and/or his supplier(s) and/or their suppliers, etc., as appropriate.

Competent bodies shall preferentially recognise attestations which are issued by bodies accredited according to the relevant harmonised standard for testing and calibration laboratories and verifications by bodies that are accredited according to the relevant harmonised standard for bodies certifying products, processes and services.

Where appropriate, test methods other than those indicated for each criterion may be used if the competent body assessing the application accepts their equivalence.

Where appropriate, competent bodies may require supporting documentation and may carry out independent verifications.

As a pre-requisite, the product must meet all respective legal requirements of the country (countries) in which the product is intended to be placed on the market. The applicant shall declare the product's compliance with this requirement.

The EU Ecolabel criteria reflect the best environmental performing products on the furniture market. The criteria are focused on a ‘per material’ basis for ease of assessment given that many furniture products will only contain one or two of the above listed materials.

Whilst the use of chemicals and release of pollutants is part of the production process, the use of hazardous substances are excluded whenever possible or limited to the minimum necessary to provide an adequate function and at the same time strict quality and safety standards for furniture products. For this purpose, derogation conditions for specific substances/groups of substances are granted in exceptional circumstances, in order not to shift the environmental burden to other life cycle phases or impacts and only when there are no viable alternatives existing on the market.

Technical drawings that illustrate the assembly of component parts/materials and sub-component parts/materials that form the final furniture product and its dimensions shall be provided to the competent body along with a bill of materials for the product that shall state the total weight of the product itself and how this is split between the following different materials: solid wood, wood-based panels, cork, bamboo, rattan, plastics, metals, leather, coated fabrics, textiles, glass and padding/filling materials.

Any remaining materials that do not fall within the categories above shall be listed as ‘other’ materials.

The total quantity of ‘other’ materials shall not exceed 5 % of the total product weight.

Assessment and verification: The applicant shall provide documentation to the competent body containing:

(i)

Technical drawings that illustrate the different component parts/materials and sub-component parts/materials used in the assembly of the furniture product;

(ii)

An overall bill of materials stating the total weight of the product unit and how the weight is split amongst solid wood, wood-based panels, cork, bamboo, rattan, plastics, metals, leather, textiles, coated fabrics, glass, padding/filling and ‘other’ materials. Weights of different materials shall be expressed as grams or kilograms and as a percentage of the total product unit weight.

The presence in the product and any component parts/materials thereof, of substances that are identified according to Article 59(1) of Regulation (EC) No 1907/2006 as substances of very high concern (SVHCs) or substances and mixtures that meet the criteria for Classification, Labelling and Packaging (CLP) according to Regulation (EC) No 1272/2008 of the European Parliament and of the Council [Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16 December 2008 on classification, labelling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006 (OJ L 353, 31.12.2008, p. 1).] for the hazards listed in Table 1, shall be restricted in accordance with criteria 2.1, 2.2(a) and 2.2(b).

For the purpose of this criterion Candidate List SVHCs and CLP hazard classifications are grouped in Table 1 according to their hazardous properties.

Hazards that identify a substance or mixture as being within Group 1:

Substances that appear on the Candidate List for SVHCs

Carcinogenic, Mutagenic and/or Toxic for Reproduction (CMR) Category 1A or 1B: H340, H350, H350i, H360, H360F, H360D, H360FD, H360Fd, H360Df

Hazards that identify a substance or mixture as being within Group 2:

Category 2 CMR: H341, H351, H361f, H361d, H361fd, H362

Category 1 aquatic toxicity: H400, H410

Category 1 and 2 acute toxicity: H300, H310, H330

Category 1 aspiration toxicity: H304

Category 1 Specific Target Organ Toxicity (STOT): H370, H372

Category 1 Skin Sensitiser H317

Hazards that identify a substance or mixture as being within Group 3:

Category 2, 3 and 4 aquatic toxicity: H411, H412, H413

Category 3 acute toxicity: H301, H311, H331, EUH070

Category 2 STOT: H371, H373

The product and any component parts/materials thereof, shall not contain SVHCs, at concentrations greater than 0,10 % (weight by weight).

No derogation from this requirement shall be given to Candidate List SVHCs present in the product or any component parts/materials thereof at concentrations greater than 0,10 % (weight by weight).

Textiles that have been awarded the EU Ecolabel based on the ecological criteria established in Commission Decision 2014/350/EU [Commission Decision 2014/350/EU of 5 June 2014 establishing the ecological criteria for the award of the EU Ecolabel for textile products (OJ L 174, 13.6.2014, p. 45).] are considered to comply with criterion 2.1.

Assessment and verification: The applicant shall compile declarations of the absence of SVHCs at or above the specified concentration limit for the product and any component parts/materials used in the assembly of the product. Declarations shall be with reference to the latest version of the Candidate List published by ECHA [ECHA, Candidate List of substances of very high concern for Authorisation, http://www.echa.europa.eu/candidate-list-table.].

For textiles that have been awarded the EU Ecolabel in accordance with Decision 2014/350/EU, a copy of the EU Ecolabel certificate must be provided as a proof of compliance.

The requirements are split into two parts, based on the production stage of the furniture product. Part a) refers to substances and mixtures used during any finishing or assembly operations carried out directly by the furniture manufacturer. Part b) refers to substances and mixtures used during the production of supplied component parts/materials.

Textiles that have been awarded the EU Ecolabel based on the ecological criteria established in Decision 2014/350/EU are considered to comply with criteria 2.2(a) and 2.2(b).

None of the adhesives, varnishes, paints, primers, wood stains, biocidal products (such as wood preservatives), flame retardants, fillers, waxes, oils, joint fillers, sealants, dyestuff, resins or lubricating oils directly used by the furniture manufacturer shall be classified with any of the CLP hazards listed in Table 1, unless their use is specifically derogated in Table 2.

This criterion shall not apply to individual component parts/materials from suppliers that: (i) weigh less than 25 g and that (ii) do not come into direct contact with users during normal use.

None of the substances or mixtures used by suppliers that fall within the scope defined below shall be classified with any of the CLP hazards listed in Table 1, unless their use is specifically derogated in Table 2:

Solid wood and wood-based panels: adhesives, varnishes, paints, wood stains, biocidal products (such as wood preservatives), primers, flame retardants fillers, waxes, oils, joint fillers, sealants and resins used.

Plastics: pigments, plasticisers, biocidal products and flame retardants used as additives.

Metals: paints, primers or varnishes applied to the metal surface.

Textiles, leather and coated fabric upholstery: dyestuff, varnishes, optical brighteners, stabilisers, auxiliary compounds, flame retardants, plasticisers, biocidal products or water/dirt/stain repellents used.

Upholstery padding materials: biocidal products, flame retardants or plasticisers applied to the material.

[Colour removal in wastewater treatment shall be considered as taking place when effluents from the dyehouse meets the following spectral coefficients: (i) 7m– 1 at 436 nm, 5m– 1 at 525 nm and 3m– 1 at 620 nm.]

Substance/mixture type | Applicability | Derogated classification(s) | Derogation conditions

(a)

Biocidal products (such as wood preservatives)

Treatment of furniture component parts and/or upholstery materials to be used in the final product | All group 2 and 3 hazards listed in Table 1 except for CMR hazards |

Only if the active substance contained in the biocidal product is approved, or under examination pending a decision on approval, under Regulation (EU) No 528/2012 or included in Annex I of that Regulation, and in the following circumstances, as appropriate:

i.

For in-can preservatives present in coating formulations applied to indoor or outdoor furniture component parts/materials.

ii.

For dry-film preservatives present in coatings applied to outdoor furniture only.

iii. For preservation treatment of wood to be used in outdoor furniture but only if the original wood does not meet the requirements for Durability class 1 or 2 as per EN 350.

iv. For textile fabrics or coated fabrics used in outdoor furniture products.

Verification:

The applicant shall declare which, if any, active substances contained in the biocidal product have been used in the manufacture of different furniture component parts/materials, supported by declarations from suppliers, relevant SDSs, CAS numbers and results from EN 350 testing, as appropriate.

(b)

Flame retardants

Textiles, leather, coated fabrics in furniture upholstery covering materials and also padding materials | H317, H373, H411, H412, H413 | The product must be intended to be used in applications in which it is required to meet fire protection requirements for ISO, EN, Member State or public sector procurement standards and regulations.

(c)

Flame retardants/Antimony Trioxide (ATO)

H351 |

ATO is only permitted when all of the following conditions are met:

i.

The product must be intended to be used in applications in which it is required to meet fire protection requirements in ISO, EN, Member State or public sector procurement standards and regulations.

ii.

It is used as a synergist with textiles or coated fabrics.

iii. Emissions to air in the workplace where the flame retardant is applied to the textile product shall meet an eight hour occupational exposure limit value of 0,50 mg/m3.

(d)

Nickel

Metal component parts | H317, H351, H372 | Only permitted when used in stainless steel or nickel-plated component parts and when the nickel release rate is less than 0,5 μg/cm2/week according to EN 1811.

(e)

Chromium compounds

H317, H411 | Derogation only applies to chromium III compounds used in electroplating operations (e.g., chromium III chloride).

(f)

Zinc compounds

H300, H310, H330, H400, H410 | Derogation only applies to zinc compounds used in electroplating or hot-dip galvanisation operations (such as, zinc oxide, zinc chloride and zinc cyanide).

(g)

Dyestuff for dyeing and non-pigment printing

Textiles, leather and coated fabrics in furniture upholstery covering materials | H301, H311, H317, H331 | When dust free dye formulations or automatic dosing and dispensing of dyes are used by dye houses and printers to minimise worker exposure.

H411, H412, H413 |

Dyeing processes using reactive, direct, vat or sulphur dyes with these classifications shall meet a minimum of one of the following conditions:

i.

Use of high affinity dyes;

ii.

Achievement of a reject rate of less than 3,0 %;

iii. Use of colour matching instrumentation;

iv. Implementation of standard operating procedures for the dyeing process;

v.

Use of colour removal to treat wastewater.

The use of solution dyeing and/or digital printing is exempted from these conditions.

(h)

Optical brighteners

Textiles, leather and coated fabrics in furniture upholstery covering materials | H411, H412, H413 |

Optical brighteners may only be applied in the following cases:

i.

In white coloured printing;

ii.

As additives during the production of acrylic, polyamide or polyester with a recycled content.

(i)

Water, dirt and stain repellents

Use in any surface treatments of furniture component parts/materials | H413 |

The repellent and its degradation products shall either:

i.

be readily and/or inherently biodegradable or

ii.

have a low potential to bioaccumulate (an octanol-water partition coefficient Log Kow ≤ 3,2 or a Bioconcentration Factor (BCF) < 100) in the aquatic environment, including aquatic sediment.

(j)

Stabilisers and varnishes

Use in coated fabric production | H411, H412, H413 | Automatic dosing and/or personal protective equipment must be used to minimise worker exposure. At least 95 % of these additives must show at least 80 % degradation of dissolved organic carbon within 28 days using OECD 303A/B and/or ISO 11733 test methods.

(k)

Auxiliaries (comprising carriers, levelling agents, dispersing agents, surfactants, thickeners and binders)

Use in treatment of furniture upholstery covering materials (textiles, leather or coated fabrics) | H301, H311, H317, H331, H371, H373, H411, H412, H413, EUH070 |

Recipes shall be formulated using automatic dosing systems and processes shall follow standard operating procedures.

Substances classified with H311 or H331 shall not be present on the material at concentrations greater than 1,0 % w/w.

(l)

Paints, varnishes, resins and adhesives

Any furniture component part/material | H304, H317, H412, H413, H371, H373 | A Safety Data Sheet (SDS) of the chemical mixture which clearly outlines the correct Personal Protective Equipment and adequate procedures for storage, handling, use and disposal of these mixtures during use and a declaration of proof of compliance with these measures shall be provided.

H350 | Only applicable to formaldehyde-based resins where the free formaldehyde content in the resin formulation (resins, adhesives and hardeners) does not exceed 0,2 % (w/w) as determined by ISO 11402 or equivalent methodology.

(m)

Lubricating oils

In component parts designed to move repeatedly during normal use | All Group 2 hazards except CMR and all Group 3 hazards listed in Table 1 | Lubricants shall only be permitted for use if it can be demonstrated by relevant OECD or ISO tests to be readily or inherently biodegradable in the aquatic environment, including aquatic sediment.

Assessment and verification: The applicant shall provide a declaration of compliance with criterion 2.2(a) and 2.2(b) supported, where appropriate, by declarations from suppliers. Declarations shall be supported by lists of relevant mixtures or substances used together with information about their hazard classification or non-classification.

The following information shall be provided to support declarations of the hazard classification or non-classification for each substance or mixture:

(i)

The CAS, EC or list number (where available for mixtures);

(ii)

The physical form and state in which the substance or mixture is used;

(iii)

Harmonised CLP hazard classifications for substances;

(iv)

Self-classification entries in ECHA's REACH registered substance database [ECHA, REACH registered substances database: http://www.echa.europa.eu/information-on-chemicals/registered-substances.] (if no harmonised classification is available).

(v)

Mixture classifications according to the criteria laid down in the CLP Regulation.

When considering self-classification entries in the REACH registered substance database, priority shall be given to entries from joint submissions.

Where a classification is recorded as ‘data-lacking’ or ‘inconclusive’ according to the REACH registered substance database, or where a substance has not yet been registered under the REACH system, toxicological data meeting the requirements in Annex VII to Regulation (EC) No 1907/2006 shall be provided that is sufficient to support conclusive self-classifications in accordance with Annex I to Regulation (EC) No 1272/2008 and ECHA's supporting guidance. In the case of ‘data lacking’ or ‘inconclusive’ database entries, self-classifications shall be verified, with the following information sources being accepted:

(i)

Toxicological studies and hazard assessments by ECHA peer regulatory agencies [ECHA, Cooperation with peer regulatory agencies, http://echa.europa.eu/about-us/partners-and-networks/international-cooperation/cooperation-with-peer-regulatory-agencies.], Member State regulatory bodies or Intergovernmental bodies;

(ii)

A Safety Data Sheet (SDS) fully completed in accordance with Annex II to Regulation (EC) No 1907/2006;

(iii)

A documented expert judgment provided by a professional toxicologist. This shall be based on a review of scientific literature and existing testing data, where necessary supported by results from new testing carried out by independent laboratories using methods approved by ECHA;

(iv)

An attestation, where appropriate based on expert judgment, issued by an accredited conformity assessment body that carries out hazard assessments according to the Globally Harmonised System (GHS) of the classification and labelling of chemicals or CLP hazard classification systems.

Information on the hazardous properties of substances or mixtures may, in accordance with Annex XI to Regulation (EC) No 1907/2006, be generated by means other than tests, for instance through the use of alternative methods such as in vitro methods, by quantitative structure activity models or by the use of grouping or read-across.

For the derogated substances and mixtures listed in Table 2, the applicant shall provide proof that all derogation conditions are met.

Textile-based materials that have been awarded the EU Ecolabel in accordance with Decision 2014/350/EU shall be considered compliant with criteria 2.2(a) and 2.2(b), however a copy of the EU Ecolabel certificate must be provided.

The term ‘wood’ applies not only to solid wood but also to wood chips and wood fibres. Where criteria refer solely to wood-based panels, this is mentioned in the title of those criteria.

Plastic foils manufactured using Vinyl Chloride Monomer (VCM) shall not be used in any part of the furniture product.

This criterion shall only apply when the content of wood or wood-based panels exceeds 5 % w/w of the final product weight (excluding packaging).

All wood, cork, bamboo and rattan shall be covered by chain of custody certificates issued by an independent third party certification scheme such as the Forest Stewardship Council (FSC), the Programme for the Endorsement of Forest Certification (PEFC) or equivalent.

All virgin wood, cork, bamboo and rattan shall not originate from GMO species and shall be covered by valid sustainable forest management certificates issued by an independent third party certification scheme such as FSC, PEFC or equivalent.

Where a certification scheme allows the mixing of uncertified material with certified and/or recycled materials in a product or production line, a minimum of 70 % of the wood, cork, bamboo or rattan material, as appropriate, shall be sustainable certified virgin material and/or recycled material.

Uncertified material shall be covered by a verification system which ensures that it is legally sourced, and meets any other requirement of the certification scheme with respect to uncertified material.

The certification bodies issuing forest and/or chain of custody certificates shall be accredited or recognised by that certification scheme.

Assessment and verification: The applicant or material supplier, as appropriate, shall provide a declaration of compliance supported by valid, independently certified chain of custody certificate(s) for all wood, cork, bamboo or rattan material used in the product or production line and demonstrate that at least 70 % of the material originates from forests or areas managed according to Sustainable Forestry Management principles and/or from recycled sources that meet the requirements set out by the relevant independent chain of custody scheme. FSC, PEFC or equivalent schemes shall be accepted as independent third party certification. In case the scheme does not specifically require that all virgin material is sourced from non-GMO species, additional evidence shall be provided to demonstrate this.

If the product or production line includes uncertified virgin material, proof shall be provided that the content of uncertified virgin material does not exceed 30 % and is covered by a verification system which ensures that it is legally sourced and meets any other requirement of the certification scheme with respect to uncertified material.

In addition to the General conditions on hazardous substances set out in criterion 2, the following conditions shall specifically apply to any furniture component parts made of wood, cork, bamboo or rattan or specifically only to wood-based panels where the latter term is mentioned in the criterion title:

Any recycled wood fibres or wood chips used in the manufacture of wood based panels shall be tested in accordance with the European Panel Federation (EPF) standard for delivery conditions of recycled wood [‘EPF Standard for delivery conditions of recycled wood’, October 2002. Can be viewed online at: http://www.europanels.org/upload/EPF-Standard-for-recycled-wood-use.pdf] and comply with the limits for contaminants as listed in Table 3.

Contaminant |

Limit values

(mg/kg recycled wood)

Contaminant |

Limit values

(mg/kg recycled wood)

Arsenic (As) | 25 | Mercury (Hg) | 25

Cadmium (Cd) | 50 | Fluorine (F) | 100

Chromium (Cr) | 25 | Chlorine (Cl) | 1000

Copper (Cu) | 40 | Pentachlorophenol (PCP) | 5

Lead (Pb) | 90 | Creosote (Benzo(a)pyrene) | 0,5

Assessment and verification: The applicant shall provide either:

(i)

A declaration from the wood-based panel manufacturer that no recycled wood fibres were used in the panel, or

This article is long: the rest is at the official publication.