Annex I (Part-M) to Regulation (EU) No 1321/2014 is amended as follows:
The table of contents is amended as follows:
The title of point M.A.306 is replaced by ‘M.A.306 Aircraft technical log system’;
Appendix I is replaced by ‘Appendix I — Continuing airworthiness management contract’;
In point M.1, point 4 is replaced by the following:
‘4. for the approval of maintenance programmes,
the authority designated by the Member State of registry; or
if agreed with the Member State of registry prior to the approval of the maintenance programme:
the authority designated by the State where the operator has its principal place of business or is established or residing; or
the authority responsible for the oversight of the continuing airworthiness management organisation managing the continuing airworthiness of the aircraft, or with which a limited contract in accordance with M.A.201(i)(3) has been made by the owner.’;
In point M.A.201, points (d), (e), (f), (g), (h), (i) and (j) are replaced by the following:
‘(d) The pilot-in-command or, in the case of air carriers licenced in accordance with Regulation (EC) No 1008/2008, the operator shall be responsible for the satisfactory accomplishment of the pre-flight inspection. This inspection must be carried out by the pilot or another qualified person but need not be carried out by an approved maintenance organisation or by Part-66 certifying staff.
In the case of aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the operator is responsible for the continuing airworthiness of the aircraft it operates and shall:
ensure that no flight takes place unless the conditions defined in point (a) are met;
be approved, as part of its air operator certificate, as a continuing airworthiness management organisation pursuant to M.A. Subpart G (CAMO) for the aircraft it operates; and
be approved in accordance with Part-145 or establish a contract in accordance with M.A.708(c) with such organisation.
For complex motor-powered aircraft used for commercial specialised operations, or CAT other than those by air carriers licenced in accordance with Regulation (EC) No 1008/2008, or commercial ATOs, the operator shall ensure that:
no flight takes place unless the conditions defined in paragraph (a) are met;
the tasks associated with continuing airworthiness are performed by an approved CAMO. When the operator is not CAMO approved itself then the operator shall establish a written contract in accordance with Appendix I with such an organisation, and
the CAMO referred to in (2) is approved in accordance with Part-145 for the maintenance of the aircraft and components for installation thereon, or it has established a contract in accordance with M.A.708(c) with such organisations.
For complex motor-powered aircraft not included in point (e) or point (f), the owner shall ensure that:
no flight takes place unless the conditions defined in paragraph (a) are met;
the tasks associated with continuing airworthiness are performed by an approved CAMO. When the owner is not CAMO approved itself then the owner shall establish a written contract in accordance with Appendix I with such an organisation, and
the CAMO referred to in (2) is approved in accordance with Part-145 for the maintenance of the aircraft and components for installation thereon, or it has established a contract in accordance with M.A.708(c) with such organisations.
For other than complex motor-powered aircraft, used for commercial specialised operations, or CAT other than those by licenced air carriers in accordance with Regulation (EC) No 1008/2008, or commercial ATOs, the operator shall ensure that:
no flight takes place unless the conditions defined in point (a) are met;
the tasks associated with continuing airworthiness are performed by an approved CAMO. When the operator is not CAMO approved itself then the operator shall establish a written contract in accordance with Appendix I with such an organisation, and
the CAMO referred to in point (2) is approved in accordance with Part-M Subpart-F or Part-145 for the maintenance of the aircraft and components for installation thereon, or it has established a contract in accordance with M.A.708(c) with such organisations.
For other than complex motor-powered aircraft not included in point (e) or (h), or used for “limited operations”, the owner is responsible for ensuring that no flight takes place unless the conditions defined in point (a) are met. To that end, the owner shall:
contract the tasks associated with continuing airworthiness to an approved CAMO though a written contract in accordance with Appendix I, which will transfer the responsibility for the accomplishment of these tasks to the contracted CAMO, or;
manage the continuing airworthiness of the aircraft under its own responsibility, without contracting an approved CAMO, or;
manage the continuing airworthiness of the aircraft under its own responsibility and establish a limited contract for the development of the maintenance programme and for processing its approval in accordance with point M.A.302 with:
an approved CAMO, or
in the case of ELA2 aircraft, a Part-145 or M.A. Subpart F maintenance organisation.
This limited contract transfers the responsibility for the development and, except in the case where a declaration is issued by the owner in accordance with M.A.302(h), processing the approval of the maintenance programme to the contracted organisation.
The owner/operator shall ensure that any person authorised by the competent authority is granted access to any of its facilities, aircraft or documents related to its activities, including any subcontracted activities, to determine compliance with this Part.’;
Point M.A.301 is amended as follows:
Point 2 is replaced by the following:
‘2. the rectification in accordance with data specified in point M.A.304 and/or point M.A.401, as applicable, of any defect and damage affecting safe operation taking into account, the minimum equipment list (MEL) and configuration deviation list, when applicable;’;
Point 4 is replaced by the following:
‘4. for all complex motor-powered aircraft or aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the analysis of the effectiveness of the M.A.302 approved maintenance programme;’;
Point 7 is replaced by the following:
‘7. for non-mandatory modifications and/or inspections, for all complex motor-powered aircraft or aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the establishment of an embodiment policy;’;
Point M.A.302 is amended as follows:
Point (c) is replaced by the following:
‘(c) When the continuing airworthiness of the aircraft is managed by a continuing airworthiness management organisation approved in accordance with Section A, Subpart G of this Annex (Part M) or when there is a limited contract between the owner and this organisation in accordance with point M.A.201(i)(3), the aircraft maintenance programme and its amendments may be approved through an indirect approval procedure.
In that case, the indirect approval procedure shall be established by the continuing airworthiness management organisation as part of the Continuing Airworthiness Management Exposition and shall be approved by the competent authority responsible for that continuing airworthiness management organisation.
The continuing airworthiness management organisation shall not use the indirect approval procedure when this organisation is not under the oversight of the Member State of Registry, unless an agreement exists in accordance with point M.1, paragraph 4(ii), transferring the responsibility for the approval of the aircraft maintenance programme to the competent authority responsible for the continuing airworthiness management organisation.’;
Point (f) is replaced by the following:
‘(f) For complex motor-powered aircraft, when the maintenance programme is based on maintenance steering group logic or on condition monitoring, the aircraft maintenance programme shall include a reliability programme.’;
In point M.A.305, point 2 of point (b) is replaced by the following:
‘2. when required in point M.A.306, the operator's technical log.’;
Point M.A.306 is amended as follows:
The title is replaced by the following:
point (a) is replaced by the following:
‘(a) For CAT, commercial specialised operations and commercial ATO operations, in addition to the requirements of M.A.305, the operator shall use a technical log system containing the following information for each aircraft:
information about each flight, necessary to ensure continued flight safety, and;
the current aircraft certificate of release to service, and;
the current maintenance statement giving the aircraft maintenance status of what scheduled and out of phase maintenance is next due except that the competent authority may agree to the maintenance statement being kept elsewhere, and;
all outstanding deferred defects rectifications that affect the operation of the aircraft, and;
any necessary guidance instructions on maintenance support arrangements.’;
Point M.A.402 is replaced by the following:
Except for maintenance performed by a maintenance organisation approved in accordance with Annex II (Part-145), any person or organisation performing maintenance shall:
be qualified for the tasks performed, as required by this part;
ensure that the area in which maintenance is carried out is well organised and clean in respect of dirt and contamination;
use the methods, techniques, standards and instructions specified in the M.A.401 maintenance data;
use the tools, equipment and material specified in the M.A.401 maintenance data. If necessary, tools and equipment shall be controlled and calibrated to an officially recognised standard;
ensure that maintenance is performed within any environmental limitations specified in the M.A.401 maintenance data;
ensure that proper facilities are used in case of inclement weather or lengthy maintenance;
ensure that the risk of multiple errors during maintenance and the risk of errors being repeated in identical maintenance tasks are minimised;
ensure that an error capturing method is implemented after the performance of any critical maintenance task; and
carry out a general verification after completion of maintenance to ensure the aircraft or component is clear of all tools, equipment and any extraneous parts or material, and that all access panels removed have been refitted.’;
In point M.A.403, points (b) and (c) are replaced by the following
‘(b) Only the authorised certifying staff, according to points M.A.801(b)1, M.A.801(b)2, M.A.801(c), M.A.801(d) or Annex II (Part-145) can decide, using M.A.401 maintenance data, whether an aircraft defect hazards seriously the flight safety and therefore decide when and which rectification action shall be taken before further flight and which defect rectification can be deferred. However, this does not apply when the MEL is used by the pilot or by the authorised certifying staff.
Any aircraft defect that would not hazard seriously the flight safety shall be rectified as soon as practicable, after the date the aircraft defect was first identified and within any limits specified in the maintenance data or the MEL.’;
In point M.A.502, point (d) is replaced by the following:
‘(d) By derogation from point (a) and point M.A.801(b)2, maintenance of a component while installed or temporarily removed from an ELA1 aircraft used by other than licenced air carriers in accordance with Regulation (EC) No 1008/2008, and performed in accordance with component maintenance data, may be performed by certifying staff referred to in point M.A.801(b)2, except for:
overhaul of components other than engines and propellers, and;
overhaul of engines and propellers for aircraft other than CS-VLA, CS-22 and LSA.
Component maintenance performed in accordance with point (d) is not eligible for the issuance of an EASA Form 1 and shall be subject to the aircraft release requirements provided for in point M.A.801.’;
In point M.A.504, point (b) is replaced by the following:
‘(b) Unserviceable components shall be identified and stored in a secure location under the control of an approved maintenance organisation until a decision is made on the future status of such component. Nevertheless, for aircraft not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008 and other than complex motor-powered aircraft, the person or organisation that declared the component unserviceable may transfer its custody, after identifying it as unserviceable, to the aircraft owner provided that such transfer is reflected in the aircraft logbook or engine logbook or component logbook.’;
Point M.A.601 is replaced by the following:
This Subpart establishes the requirements to be met by an organisation to qualify for the issue or continuation of an approval for the maintenance of aircraft other than complex motor powered aircraft and components to be installed therein not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008.’;
Point M.A.606 is amended as follows:
Point (g) is replaced by the following:
‘(g) The maintenance organisation shall have sufficient certifying staff to issue M.A.612 and M.A.613 certificates of release to service for aircraft and components. They shall comply with the requirements of Article 5 of Regulation (EU) No 1321/2014’;
In point M.A.703, point (b) is replaced by the following:
‘(b) Notwithstanding point (a), for licenced air carriers in accordance with Regulation (EC) No 1008/2008, the approval shall be part of the air operator certificate issued by the competent authority, for the aircraft operated.’;
In point M.A.704 point (a), point 9 is replaced by the following:
‘9. the list of approved aircraft maintenance programmes, or, for aircraft not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the list of “generic” and “baseline” maintenance programmes.’;
Point M.A.706 is amended as follows:
Point (b) is replaced by the following:
‘(b) For licenced air carriers in accordance with Regulation (EC) No 1008/2008 the accountable manager referred to in point (a) shall be the person who also has corporate authority for ensuring that all the operations of the operator can be financed and carried out to the standard required for the issue of an air operator's certificate.’;
Point (d) is replaced by the following:
‘(d) For licenced air carriers in accordance with Regulation (EC) No 1008/2008, the accountable manager shall designate a nominated post holder. This person shall be responsible for the management and supervision of continuing airworthiness activities, pursuant to point (c).’;
Point (k) is replaced by the following:
‘(k) For complex motor-powered aircraft and for aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the organisation shall establish and control the competence of personnel involved in the continuing airworthiness management, airworthiness review and/or quality audits in accordance with a procedure and to a standard agreed by the competent authority;’;
Point M.A.707 is amended as follows:
Point (a) is replaced by the following:
‘(a) To be approved to carry out airworthiness reviews and, if applicable, to issue permits to fly, an approved continuing airworthiness management organisation shall have appropriate airworthiness review staff to issue airworthiness review certificates or recommendations referred to in Section A of Subpart I and, if applicable, to issue a permit to fly in accordance with point M.A.711(c):
For aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, and aircraft above 2730 kg MTOM, except balloons, these staff shall have acquired:
at least 5 years' experience in continuing airworthiness, and;
an appropriate license in compliance with Annex III (Part-66) or an aeronautical degree or a national equivalent, and;
formal aeronautical maintenance training, and;
a position within the approved organisation with appropriate responsibilities.
Notwithstanding points (a) to (d), the requirement laid down in point M.A.707(a)1(b) may be replaced by 5 years of experience in continuing airworthiness additional to those already required by point M.A.707(a)1(a).
For aircraft not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008 of 2730 kg MTOM and below, and balloons, these staff shall have acquired:
at least 3 years' experience in continuing airworthiness, and;
an appropriate license in compliance with Annex III (Part-66) or an aeronautical degree or a national equivalent, and;
appropriate aeronautical maintenance training, and;
a position within the approved organisation with appropriate responsibilities;
Notwithstanding points (a) to (d), the requirement laid down in point M.A.707(a)2(b) may be replaced by 4 years of experience in continuing airworthiness additional to those already required by point M.A.707(a)2(a).’;
Point M.A.708 is amended as follows:
In point (b), point (2) is replaced by the following:
‘2. present the aircraft maintenance programme and its amendments to the competent authority for approval, unless covered by an indirect approval procedure in accordance with point M.A.302(c), and for aircraft not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008 provide a copy of the programme to the owner or operator responsible in accordance with M.A.201;’;
Point (c) is replaced by the following:
‘(c) In the case of complex motor-powered aircraft or aircraft used for CAT, or aircraft used for commercial specialised operations or commercial ATO operations, when the continuing airworthiness management organisation is not appropriately approved to Part-145 or Part-M.A. Subpart-F, the organisation shall in consultation with the operator, establish a written maintenance contract with a Part-145 or Part-M.A. Subpart-F approved organisation or another operator, detailing the functions specified under M.A.301-2, M.A.301-3, M.A.301-5 and M.A.301-6, ensuring that all maintenance is ultimately carried out by a Part-145 or Part-M.A. Subpart-F approved maintenance organisation and defining the support of the quality functions of M.A.712(b).’;
The following point (d) is added:
‘(d) Notwithstanding point (c), the contract may be in the form of individual work orders addressed to the Part-145 or Part-M.A. Subpart-F maintenance organisation in the case of:
an aircraft requiring unscheduled line maintenance,
component maintenance, including engine maintenance.’;
In point M.A.709, point (b) is replaced by the following:
‘(b) For aircraft not used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the approved continuing airworthiness management organisation may develop “baseline” and/or “generic” maintenance programmes in order to allow for the initial approval and/or the extension of the scope of an approval without having the contracts referred to in Appendix I to this Annex (Part M). These “baseline” and/or “generic” maintenance programmes however do not preclude the need to establish an adequate Aircraft Maintenance Programme in compliance with point M.A.302 in due time before exercising the privileges referred to in point M.A.711.’;
In point M.A.711 point (a), points 1 and 2 are replaced by the following:
‘1. manage the continuing airworthiness of aircraft, except those used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, as listed on the approval certificate.
manage the continuing airworthiness of aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, when listed both on its approval certificate and on its Air Operator Certificate (AOC).’;
In point M.A.712 points (e) and (f) are replaced by the following:
‘(e) For licenced air carriers in accordance with Regulation (EC) No 1008/2008 the M.A. Subpart G quality system shall be an integrated part of the operator's quality system.
In the case of a small organisation not managing the continuing airworthiness of aircraft used by licenced air carriers in accordance with Regulation (EC) No 1008/2008, the quality system may be replaced by regular organisational reviews subject to the approval of the competent authority, except when the organisation issues airworthiness review certificates for aircraft above 2730 kg MTOM other than balloons. In the case where there is no quality system, the organisation shall not contract continuing airworthiness management tasks to other parties.’;
In point M.A.801, points (c) and (d) are replaced by the following:
‘(c) By derogation from point M.A.801(b)2 for ELA1 aircraft not used in CAT or not used in commercial specialised operations or not used in commercial ATO operations, aircraft complex maintenance tasks listed in Appendix VII may be released by certifying staff referred to in point M.A.801(b)2;
By derogation from point M.A.801(b), in the case of unforeseen situations, when an aircraft is grounded at a location where no approved maintenance organisation appropriately approved under this Annex or Annex II (Part-145) and no appropriate certifying staff are available, the owner may authorise any person, with no less than 3 years of appropriate maintenance experience and holding the proper qualifications, to maintain according to the standards set out in Subpart D of this Annex and release the aircraft. The owner shall in that case:
obtain and keep in the aircraft records details of all the work carried out and of the qualifications held by that person issuing the certification; and
ensure that any such maintenance is rechecked and released by an appropriately authorised person referred to in point M.A.801(b) or an organisation approved in accordance with Section A, Subpart F of this Annex (Part-M), or with Annex II (Part-145) at the earliest opportunity but within a period not exceeding 7 days; and
notify the organisation responsible for the continuing airworthiness management of the aircraft when contracted in accordance with point M.A.201 (i), or the competent authority in the absence of such a contract, within 7 days of the issuance of such certification authorisation.’;
In point M.A.803, point (b) is replaced by the following: