ANNEX I, Regulation (EU) 2015/1375

In forcesince 9 Apr 2025cited 3×
1.

The reference method of detection for the examination of samples for Trichinella, shall be ISO 18743:2015/Amd1:2023.

2.

The following rules shall apply only to the examination of meat of domestic swine:

(a)

In the case of whole carcasses of domestic swine other than breeding sows and boars, a specimen weighing at least 1 g shall be taken from a pillar of the diaphragm at the transition to the sinewy part. Special trichinae forceps may be used provided that an accuracy of between 1,00 and 1,15 g can be guaranteed.

In the case of whole carcasses of breeding sows and boars, a larger sample weighing at least 2 g shall be taken from a pillar of the diaphragm at the transition to the sinewy part.

In the absence of diaphragm pillars, a specimen of 2 g shall be taken from the rib part or the breastbone part of the diaphragm, or from the jaw muscle, tongue or abdominal muscles of domestic swine other than breeding sows and boars, and a specimen of 4 g shall be taken from the same tissues of breeding sows and boars.

(b)

For cuts of meat, a sample weighing at least 5 g of striated muscle, and containing little fat shall be taken, where possible from close to bones or tendons. A sample of the same size shall be collected from meat that is not intended to be cooked thoroughly or other types of post-slaughter processing.

(a)

Knife or scissors for cutting specimens.

(b)

Trays marked off with 50 squares, each of which can hold samples of approximately 2 g of meat, or other tools giving equivalent guarantees as regards the traceability of the samples.

(c)

Meat mincer or electrical blender.

(d)

A Stomacher lab-blender 3 500 thermo model.

(e)

Plastic bags suitable for the Stomacher lab-blender.

(f)

Conical separation funnels, capacity 2 litres, preferably fitted with Teflon safety plugs.

(g)

Stands, rings and clamps.

(h)

Sieves, mesh size 180 microns, external diameter 11 cm, with stainless steel or brash mesh.

(i)

Funnels, internal diameter not less than 12 cm, to support the sieves.

(j)

100 ml glass measuring cylinders.

(k)

A thermometer accurate to 0,5 °C within the range 20 °C to 70 °C.

(l)

A vibrator, e.g. an electric shaver with the head removed.

(m)

A relay which will switch on and off at one-minute intervals.

(n)

A trichinoscope with a horizontal table or a stereo-microscope, with a sub-stage transmitted light source of adjustable intensity.

(o)

Petri dishes of approximately 90 mm in diameter, gridded with squares of approximately 1 cm, or equivalent equipment for larval counting as in point 6.14 of the ISO 18743:2015/Amd1:2023.

(p)

17,5 % hydrochloric acid.

(q)

Pepsin with the following strength:

if powder or granular: 1:10000 NF (US National Formulary) corresponding to 1:12500 BP (British Pharmacopoeia) and to 2000 FIP (Fédération internationale de pharmacie), or

if liquid: stabilised liquid pepsin with minimum 660 European Pharmacopoeia units/ml.

Other pepsin activities can be used, provided the final activity in the digest fluid is equivalent to the activity of 10 g of 1:10000 NF as stipulated in point 5.3 of the ISO 18743:2015/Amd1:2023.

(r)

A number of 10 litre bins to be used for decontamination of apparatus, e.g. with formol, and for digestive juice remaining where specimens test positive.

(s)

Calibrated scale, for weighing samples and/or pepsin (accuracy ± 0,1 g).

As stipulated in Chapter I and in point 4.2 of the ISO 18743:2015/Amd1:2023 (see also Annexes A and B thereto for further details).

Grinding the meat samples in a meat mincer beforehand will improve the digestion quality. If an electrical blender is used, the blender must be operated three to four times for approximately one second each time.

This procedure may involve complete pools (100 g of samples at a time) or pools of less than 100 g.

(a)

Complete pools (100 samples at a time):

(i)

The Stomacher lab-blender 3 500 is fitted with a double plastic bag and the temperature control set at 40 to 41 °C.

(ii)

One and a half litres of water preheated to 40 to 41 °C is poured into the inner plastic bag.

(iii)

25 ml of 17,5 % hydrochloric acid is added to the water in the Stomacher.

(iv)

100 samples weighing approximately 1 g each (at 25 to 30 °C) taken from each individual sample in accordance with point 2 are added.

(v)

Lastly, 6 g pepsin or 18 ml liquid pepsin is added. This order must be followed strictly to avoid decomposition of the pepsin.

(vi)

The Stomacher is then allowed to pound the content of the bag for 25 minutes.

(vii)

The plastic bag is removed from the Stomacher and the digestion fluid is filtered through the sieve into a 3 litre beaker.

(viii)

The plastic bag is washed with approximately 100 ml of water, which is then used to rinse the sieve and lastly added to the filtrate in the beaker.

(ix)

Up to 15 individual samples can be added to a total pool of 100 samples and examined together with these samples.

(b)

Smaller pools (less than 100 samples):

(i)

The Stomacher lab-blender 3 500 is fitted with a double plastic bag and the temperature control set at 40 to 41 °C.

(ii)

A digestion fluid is prepared by mixing about one and a half litres of water and 25 ml of 17,5 % hydrochloric acid. 6 g of pepsin is added and the whole mixed at a temperature of 40 to 41 °C. This order must be followed strictly to avoid decomposition of the pepsin.

(iii)

Of the digestion fluid, a volume corresponding to 15 ml per gram of sample is measured (e.g. for 30 samples the volume required is 30 × 15 ml = 450 ml) and transferred to the inner of the two plastic bags, together with the meat samples weighing approximately 1 g (at 25 to 30 °C) taken from each individual sample in accordance with point 2.

(iv)

Water at a temperature of approximately 41 °C is poured into the outer bag to make up a total volume in the two bags of one and a half litres. The Stomacher is then allowed to pound the content of the bag for 25 minutes.

(v)

The plastic bag is removed from the Stomacher and the digestion fluid is filtered through the sieve into a 3 litre beaker.

(vi)

The plastic bag is washed with approximately 100 ml of water (at 25 to 30 °C), which is then used to rinse the sieve and lastly added to the filtrate in the beaker.

Ice (300 to 400 g of ice flakes, scaly ice or crushed ice) is added to the digestion fluid to bring its volume up to about 2 litres. The digestion fluid is then stirred until the ice has melted. In the case of smaller pools (see Section II(b)), the amount of ice must be reduced correspondingly.

The chilled digestion fluid is transferred to a 2 litre separation funnel, equipped with a vibrator in an extra clamp.

Sedimentation is allowed to proceed for 30 minutes, during which time the sedimentation funnel is vibrated intermittently, i.e. one minute vibration followed by a one-minute pause.

After 30 minutes, a 60 ml sample of the sediment is quickly run off into a 100 ml measuring cylinder (the funnel is rinsed with detergent solution after use).

The 60 ml sample is allowed to stand for at least 10 minutes, after which time the supernatant is withdrawn by suction to leave a volume of 15 ml, to be examined for presence of larvae.

For suction, a disposable syringe, equipped with a plastic tube, can be used. The length of the tube must be such that 15 ml remains in the measuring cylinder when the flanges of the syringe rest on the cylinder’s rim.

The remaining 15 ml is poured into a petri dish or equivalent equipment for larval counting, and examined using a trichinoscope or stereo-microscope.

The measuring cylinder is washed with 5 to 10 ml of tap water and the washings are added to the sample.

Digests are to be examined as soon as they are ready. Under no circumstances is examination to be postponed until the following day.

Where the digests are unclear, they must be clarified as follows:

the final sample of 60 ml is poured into a measuring cylinder and allowed to stand for 10 minutes; 45 ml of supernatant fluid is then removed by suction and the remaining 15 ml is made up to 45 ml with tap water,

after a further settling period of 10 minutes, 30 ml of supernatant fluid is removed by suction and the remaining 15 ml is poured into a petri dish or equivalent equipment for larval counting and examined using a trichinoscope or stereo-microscope.

the measuring cylinder is washed with 10 ml of tap water and these washings are added to the sample in the petri dish or equivalent equipment for larval counting and examined using a trichinoscope or stereo-microscope.

Where examination of a collective sample produces a positive or uncertain result, a further 20 g sample is taken from each pig, as stipulated in point 4.2 of the ISO 18743:2015/Amd1:2023 (see also Annexes A and B thereto for further details). The 20 g samples from five pigs are pooled and examined using the method described in this Chapter. In this way samples from 20 groups of five pigs will be examined. When Trichinella is detected in a pooled sample from five pigs, further 20 g samples are collected from the individual pigs in the group and each is examined separately using the method described in this Chapter. Parasite samples are to be kept in 70-90 % (final concentration) ethyl alcohol for conservation and identification at species level at the EU or national reference laboratory. For decontamination procedure, see point 12 of the ISO 18743:2015/Amd1:2023.

As stipulated in Section A(1).

Additional equipment:

(a)

1 litre Gelman funnel, complete with filter holder (diameter 45 mm);

(b)

filter discs, consisting of a circular stainless steel mesh with an aperture of 35 microns (disc diameter: 45 mm), two rubber rings 1 mm thick (external diameter: 45 mm; internal diameter: 38 mm), the circular mesh being placed between the two rubber rings and bonded to them using a two-component glue suitable for the two materials;

(c)

an Erlenmeyer flask, capacity 3 litres, fitted with a side tube for suction;

(d)

a filter pump;

(e)

plastic bags, capacity at least 80 ml;

(f)

equipment for sealing the plastic bags;

(g)

rennilase, strength 1:150000 Soxhlet units per gram.

As stipulated in Chapter I and in point 4.2 of the ISO 18743:2015/Amd1:2023 (see also Annexes A and B thereto for further details).

Grinding the meat samples in a meat mincer beforehand will improve the digestion quality. If an electrical blender is used, the blender must be operated three to four times for approximately one second each time.

This procedure may involve complete pools (100 g of samples at a time) or pools of less than 100 g.

(a)

Complete pools (100 samples at a time)

See Section A(3)(II)(a).

(b)

Smaller pools (less than 100 samples)

See Section A(3)(II)(b).

(a)

Ice (300 to 400 g of ice flakes, scaly ice or crushed ice) is added to the digestion fluid to bring its volume up to about 2 litres. In the case of smaller pools, the amount of ice must be reduced correspondingly.

(b)

The digestion fluid is stirred until the ice has melted. The chilled digestion fluid is then left for at least three minutes to let the larvae coil.

(c)

The Gelman funnel, fitted with a filter holder and filter disc, is mounted on an Erlenmeyer flask connected to a filter pump.

(d)

The digestion fluid is poured into the Gelman funnel and filtered. Towards the end of filtration, the digestion fluid can be helped to pass through the filter by applying suction with the filter pump. Suction must cease before the filter becomes dry, i.e. when 2 to 5 ml of fluid is left in the funnel.

(e)

Once all the digestion fluid has been filtered, the filter disc is removed and placed in an 80 ml capacity plastic bag, together with 15 to 20 ml of rennilase solution. The rennilase solution is made by adding 2 g of rennilase to 100 ml of tap water.

(f)

The plastic bag is sealed twice and placed between the inner and outer bags in the Stomacher.

(g)

The Stomacher is allowed to pound for three minutes, e.g. while it is working on a complete or incomplete pool.

(h)

After three minutes, the plastic bag, complete with filter disc and rennilase solution, is removed from the Stomacher and opened with scissors. The liquid contents are poured into a petri dish or equivalent equipment for larval counting. The bag is washed out with 5 to 10 ml of water, which is then added to the petri dish or equivalent equipment for larval counting and examined using a trichinoscope or stereo-microscope.

(i)

Digests must be examined as soon as they are ready. Under no circumstances is examination to be postponed until the following day.

Note:Filter discs must never be used when not completely clean. Unclean discs must never be allowed to dry out. Filter discs can be cleaned by leaving them in rennilase solution overnight. Before use, they must be washed in fresh rennilase solution using the Stomacher.

As laid down in point IV of Section A(3).

(a)

Knife or scissors for cutting specimens.

(b)

Trays marked off with 50 squares, each of which can hold samples of approximately 2 g of meat, or other tools giving equivalent guarantees as regards the traceability of the samples.

(c)

A Trichomatic 35® blender with filtration insert.

(d)

Hydrochloric acid 8,5 ± 0,5 % weight.

(e)

Transparent polycarbonate membrane filters with a diameter of 50 mm and a pore size of 14 microns.

(f)

Pepsin with the following strength:

if powder or granular: 1:10000 NF (US National Formulary) corresponding to 1:12500 BP (British Pharmacopoeia) and to 2000 FIP (Fédération internationale de pharmacie), or

if liquid: stabilised liquid pepsin with minimum 660 European Pharmacopoeia units/ml.

Other pepsin activities can be used, provided the final activity in the digest fluid is equivalent to the activity of 10 g of 1:10000 NF as stipulated in point 5.3 of the ISO 18743:2015/Amd1:2023.

(g)

Calibrated scale, for weighing samples and/or pepsin (accuracy ± 0,1 g).

(h)

Tweezers with a flat tip.

(i)

A number of microscope slides with a side-length of at least 5 cm or a number of petri dishes at least 6 cm in diameter, marked on their undersides into 10 × 10 mm square areas using a pointed instrument.

(j)

A (stereo-)microscope with transmitted light (magnification 15 to 60 times) or a trichinoscope with a horizontal table.

(k)

A bin for collection of waste liquids.

(l)

A number of 10 litre bins to be used for decontamination of apparatus, e.g. with formol, and for digestive juice remaining where specimens test positive.

(m)

A thermometer accurate to 0,5 °C within the range 20 to 70 °C.

As stipulated in Chapter I and in point 4.2 of the ISO 18743:2015/Amd1:2023 (see also Annexes A and B thereto for further details).

(a)

Place the blender with the filtration insert, connect the waste tube and place the tube so it drains into the waste bin.

(b)

When the blender is switched on, heating will start.

(c)

Before this is done, the bottom valve located below the reaction chamber must be opened and closed.

(d)

Up to 35 samples weighing approximately 1 g each (at 25 to 30 °C) taken from each individual sample in accordance with point 2 are then added. Ensure that larger pieces of tendons are removed as they may clot the membrane filter.

(e)

Pour water up to the edge of a liquid chamber connected to the blender (approximately 400 ml).

(f)

Pour about 30 ml hydrochloric acid (8,5 %) to the edge of the smaller, connected liquid chamber.

(g)

Place a membrane filter under the coarse filter in the filter holder in the filter insert.

(h)

Lastly, add 7 g of pepsin or 21 ml liquid pepsin. This order must be followed strictly to avoid decomposition of the pepsin.

(i)

Close the lids of the reaction and liquid chambers.

(j)

Select the period of digestion. A short digestion period (5 minutes) must be set for pigs at the normal slaughter age and a longer time (8 minutes) for other samples.

(k)

When the start button on the blender is turned on, the process of dispensing and digestion starts automatically, followed by filtration. After 10 to 13 minutes the process is completed and stops automatically.

(l)

Open the lid of the reaction chamber after checking that the chamber is empty. If there is foam or any digestion liquid remaining in the chamber, repeat the procedure in accordance with Section V.

(a)

Remove the filter holder and transfer the membrane filter to a slide or petri dish.

(b)

Examine the membrane filter using a (stereo-)microscope or a trichinoscope.

(a)

Where the result is positive, fill the blender reaction chamber with boiling water until it is two-thirds full. Ordinary tap water is poured into the connecting liquid chamber until it covers the lower sensor. Automatic cleaning then takes place. Decontaminate the filter-holder and any other equipment, e.g. using formol.

(b)

After work is completed for the day, fill the blender liquid chamber with water and put it through a standard cycle.

Each polycarbonate membrane filter may be used no more than five times. The filter is to be turned between each use. In addition, the filter must be checked after each use for any damage which would make it unsuitable for further use.

Once the blender has been put through an automatic cycle in accordance with Section I, open the lid of the reaction chamber and check whether there is foam or any liquid remaining in the chamber. If this is the case, proceed as follows:

(a)

close the bottom valve below the reaction chamber;

(b)

remove the filter holder and transfer the membrane filter to a slide or petri dish;

(c)

put a new membrane filter in the filter holder and attach the filter holder;

(d)

fill the blender liquid chamber with water until the lower sensor is covered;

(e)

carry out the automatic cleaning cycle;

(f)

after the cleaning cycle has ended, open the lid of the reaction chamber and check whether any liquid remains;

(g)

if the chamber is empty, remove the filter holder and transfer the membrane filter to a slide or petri dish with tweezers;

(h)

examine the two membrane filters in accordance with Section II. If the filters cannot be examined, repeat the entire digestion process with a longer digestion time in accordance with Section I.

As laid down in point IV of Section A(3).

This method is only considered equivalent for the testing of meat of domestic swine.

(a)

Knife or scissors and tweezers for cutting specimens.

(b)

Trays marked off into 50 squares, each of which can hold samples of approximately 2 g of meat, or other tools giving equivalent guarantees as regards the traceability of the samples.

(c)

A blender with a sharp chopping blade. Where the samples are larger than 3 g, a meat mincer with openings of 2 to 4 mm or scissors must be used. In the case of frozen meat or tongue (after removal of the superficial layer, which cannot be digested), a meat mincer is necessary and the sample size will need to be increased considerably.

(d)

Magnetic stirrers with thermostatically controlled heating plate and Teflon-coated stirring rods approximately 5 cm long.

(e)

Glass beakers, capacity 3 litres.

(f)

Sieves, mesh size 180 microns, external diameter 11 cm, with stainless steel mesh.

(g)

Steel filtration apparatus for 20 μm mesh filters with a steel funnel.

(h)

Vacuum pump.

(i)

Metal or plastic tanks, capacity 10 to 15 litres, to collect the digestive juice.

(j)

A 3D gyratory rocker.

(k)

Aluminium foil.

(l)

25 % hydrochloric acid.

(m)

Pepsin with the following strength:

if powder or granular: 1:10000 NF (US National Formulary) corresponding to 1:12500 BP (British Pharmacopoeia) and to 2000 FIP (Fédération internationale de pharmacie), or

if liquid: stabilised liquid pepsin with minimum 660 European Pharmacopoeia units/ml.

Other pepsin activities can be used, provided the final activity in the digest fluid is equivalent to the activity of 10 g of 1:10000 NF as stipulated in point 5.3 of the ISO 18743:2015/Amd1:2023.

(n)

Tap water heated to 46 to 48 °C.

(o)

Calibrated scale, for weighing samples and/or pepsin (accuracy ± 0,1 g).

(p)

Pipettes of different sizes (1, 10 and 25 ml), micropipettes according to the latex agglutination manufacturer's instructions and pipette holders.

(q)

20 microns nylon mesh filters of a diameter that fits with the filtration system.

(r)

Plastic or steel forceps of 10 to 15 cm.

(s)

Conical vials of 15 ml.

(t)

A pestle with a Teflon or steel conical tip to fit in the conical vials.

(u)

A thermometer accurate to 0,5 °C within the range 20 to 70 °C.

(v)

Latex agglutination cards of the Trichin-L antigen test kit validated under the code No EURLP_D_001/2011.

(w)

Buffer solution with preservative (sample diluent) of the Trichin-L antigen test kit validated under the code No EURLP_D_001/2011.

(x)

Buffer supplemented with preservative (negative control) of the Trichin-L antigen test kit validated under the code No EURLP_D_001/2011.

(y)

Buffer supplemented with Trichinella spiralis antigens and preservative (positive control) of the Trichin-L antigen test kit validated under the code No EURLP_D_001/2011.

(z)

Buffer with polystyrene particles coated with antibodies supplemented with preservative (latex beads) of the Trichin-L antigen test kit validated under the code No EURLP_D_001/2011.

(aa)

Disposable sticks.

As stipulated in Chapter I and in point 4.2 of the ISO 18743:2015/Amd1:2023 (see also Annexes A and B thereto for further details).

(a)

16 ± 0,5 ml of 25 % hydrochloric acid (0,2 % final) is added to a 3 litre beaker containing 2,0 litres ± 200 ml of tap water, preheated to 46 to 48 °C; a stirring rod is placed in the beaker, the beaker is placed on the preheated plate and the stirring is started.

(b)

10 ± 1 g of powder pepsin (or 30 ± 3 ml of liquid pepsin) is added.

(c)

100-115 g of samples collected in accordance with point 2 are chopped in the blender, with 150 ± 15 ml of preheated digestion buffer.

(d)

The chopped meat is transferred to the 3 litre beaker containing the water, pepsin and hydrochloric acid.

(e)

The mincing insert of the blender is immersed repeatedly in the digestion fluid in the beaker and the blender bowl is rinsed with a small quantity of digestion fluid to remove any meat still adhering.

(f)

The beaker is covered with aluminium foil.

(g)

The magnetic stirrer must be adjusted so that it maintains a constant temperature of 44 to 46 °C throughout the operation. During stirring, the digestion fluid must rotate at a sufficiently high speed to create a deep whirl without splashing.

(h)

The digestion fluid is stirred until the meat particles disappear (approximately 30 minutes). The stirrer is then switched off and the digestion fluid is poured through the sieve into the sedimentation funnel. Longer digestion times may be necessary (not exceeding 60 minutes) in the processing of certain types of meat (tongue, game meat, etc.).

(i)

The digestion process is considered satisfactory if not more than 5 % of the starting sample weight remains on the sieve.

This article is long: the rest is at the official publication.