For the purposes of this Annex, the competent authority to which an aircraft operator needs to demonstrate compliance of its aircraft, the design of which has already been certified, with the requirements of this Annex shall be the competent authority responsible for the oversight of that operator or the Agency if the responsibility for the oversight of the operator has been allocated to the Agency in accordance with Article 64 or 65 of Regulation (EU) 2018/1139.
For the purposes of this Annex, the competent authority to which a holder of a type certificate (TC), restricted TC, supplemental type certificate (STC), design change approval or repair design approval needs to demonstrate compliance with the requirements of this Annex shall be the Agency.
A flight shall not be commenced when any of the aircraft's instruments, items of equipment, or functions required by this Part are inoperative or missing unless waived by the operator's Minimum Equipment List as defined in Part-ORO.MLR.105 and approved by the competent authority.
The Agency shall issue, in accordance with Article 76(3) of Regulation (EU) 2018/1139, certification specifications as standard means to demonstrate compliance with this Annex. The certification specifications shall be sufficiently detailed and specific to indicate the conditions under which compliance with the requirements of this Annex may be demonstrated.
Aircraft operators and holders of a TC, restricted TC, STC, design change approval, or repair design approval may demonstrate compliance with the requirements of this Annex by complying with either of the following:
the specifications issued by the Agency under point (a) or the equivalent certification specifications issued by the Agency under point 21.B.70 of Annex I (Part 21) to Regulation (EU) No 748/2012;
technical standards offering an equivalent level of safety to that of the standards included in those certification specifications.
Holders of a TC, restricted TC, STC, design change approval, or repair design approval shall make available any change to the instructions for continued airworthiness (‘ICA’) developed for the purpose of ensuring compliance with this Annex to all known operators of the affected aircraft and, on request, to any other person required to comply with such instructions, including continuing airworthiness management organisations. For the purposes of this Regulation, the ICA also include damage tolerance inspections (‘DTIs’), repair evaluation guidelines (‘REGs’), a baseline corrosion prevention and control programme (‘CPCP’) and a list of fatigue-critical structures (‘FCSs’) and airworthiness limitation sections (‘ALSs’).
Operators of large aeroplanes used in commercial air transport, type certified on or after 1 January 1958, shall ensure that each flight or cabin crew member seat and its restraint system are configured in order to provide an optimum level of protection in an emergency landing whilst allowing the occupant's necessary functions and facilitating rapid egress.
Operators of large aeroplanes used in commercial air transport of passengers, type-certified on or after 1 January 1958, and for which the individual certificate of airworthiness is first issued on or after 26 February 2021 shall demonstrate for each seat type design approved for occupancy during taxiing, take-off or landing that the occupant is protected when exposed to loads resulting from emergency landing conditions. The demonstration shall be made by one of the following means:
successfully completed dynamic tests;
rational analysis providing equivalent safety, based on dynamic tests of a similar seat type design.
The obligation set out in the first paragraph shall not apply to the following seats:
flight deck crew seats;
seats in low-occupancy aeroplanes involved only in on-demand non-scheduled commercial air transport operations;
seats in an aeroplane model listed in Table A.1 of Appendix 1 and carrying a manufacturer serial number listed in that Table.
Operators of large aeroplanes that are used in commercial air transport and that have a maximum operational passenger seating configuration of more than 19 with one or more emergency exits deactivated shall ensure that the distance(s) between the remaining exits remains (remain) compatible with effective evacuation, except for large aeroplanes that have an emergency exit configuration installed and approved before 1 April 1999.
Operators of large aeroplanes used in commercial air transport shall provide means to facilitate the rapid and easy movement of each passenger from their seat to any of the emergency exits in case of an emergency evacuation.
Operators of large aeroplanes used in commercial air transport shall comply with the following:
means shall be provided to facilitate the location, access, and operation of emergency exits by cabin occupants under foreseeable conditions in the cabin in case of an emergency evacuation;
means shall be provided to facilitate the location and operation of emergency exits by personnel on the outside of the aeroplane in case of an emergency evacuation.
Operators of large aeroplanes used in commercial air transport shall provide means to ensure that illuminated exit signage, general cabin and exit area illumination, and low level exit path illumination is available to facilitate the location of exits and movement of passengers to the exits in case of emergency evacuation.
Operators of large aeroplanes used in commercial air transport shall comply with the following:
all materials and equipment used in compartments occupied by the crew or passengers shall demonstrate flammability characteristics compatible with minimising the effects of in-flight fires and the maintenance of survivable conditions in the cabin for a time commensurate with that needed to evacuate the aircraft;
smoking prohibition shall be indicated with placards;
disposal receptacles shall be such that containment of an internal fire is ensured; such receptacles shall be marked to prohibit the disposal of smoking materials.
Operators of large aeroplanes used in commercial air transport, type certified after 1 January 1958, shall ensure that the liners of Class C or Class D cargo compartments are constructed of materials that adequately prevent the effects of a fire in the compartment from endangering the aircraft or its occupants.
Operators of large aeroplanes that are used in commercial air transport, and that were type certified on or after 1 January 1958, shall ensure that:
for large aeroplanes for which the first individual certificate of airworthiness was issued before 18 February 2021, when new thermal or acoustic insulation materials are installed as replacements on or after 18 February 2021, those new materials have flame propagation resistance characteristics which prevent or reduce the risk of flame propagation in the aeroplane;
for large aeroplanes for which the first individual certificate of airworthiness was issued on or after 18 February 2021, thermal and acoustic insulation materials have flame propagation resistance characteristics which prevent or reduce the risk of flame propagation in the aeroplane;
for large aeroplanes for which the first individual certificate of airworthiness was issued on or after 18 February 2021 and with a passenger capacity of 20 or more, thermal and acoustic insulation materials (including the means of fastening the materials to the fuselage) installed in the lower half of the aeroplane have flame penetration resistance characteristics which prevent or reduce the risk of flame penetration into the aeroplane after an accident and which ensure survivable conditions in the cabin for the time needed to evacuate the aeroplane.
Operators of large aeroplanes that are used in commercial air transport, and that were type certified on or after 1 January 1958,shall ensure that:
for large aeroplanes, the operation of which involves the transport of passengers, each Class D cargo or baggage compartment, regardless of its volume, complies with the certification specifications applicable to a Class C compartment;
for large aeroplanes, the operation of which involves the transport of cargo only, each Class D cargo compartment, regardless of its volume, complies with the certification specifications applicable to either a Class C or a Class E compartment;
This point shall not apply to operators of an aeroplane model listed in Table A.1 of Appendix 1 to this Annex.
Operators of large aeroplanes used in commercial air transport with a maximum operational passenger seating configuration of more than 19 shall comply with the following:
Lavatories shall be equipped with:
smoke detection means;
means to automatically extinguish a fire occurring in each disposal receptacle.
Operators of large aeroplanes shall ensure that the following extinguishers do not use halon as an extinguishing agent:
built-in fire extinguishers for each lavatory waste receptacle for towels, paper or waste in large aeroplanes for which the first individual certificate of airworthiness is issued on or after 18 February 2020;
portable fire extinguishers in large aeroplanes for which the first individual certificate of airworthiness is issued on or after 18 May 2019.
For large aeroplanes, as well as for small aeroplanes with a maximum take-off weight (MTOW) greater than 5700 kg (12500 lb), for which the individual certificate of airworthiness is first issued on or after 1 January 2025, the holders of:
TC or restricted TC, or
STC or design change approvals, if the change relates to the aeroplane cargo compartment fire protection capabilities,
shall make available information on the aeroplane design characteristics associated with the cargo compartment fire protection capabilities to all known operators of such aeroplanes.
For small aeroplanes with a MTOW of 5700 kg (12500 lb) or less and equipped with at least one cargo compartment separated from the flight deck, and for which the individual certificate of airworthiness is first issued on or after 1 January 2025, the holders of:
TC or restricted TC, or
STC or design change approvals, if the change relates to the aeroplane cargo compartment fire protection capabilities,
shall make available information on the aeroplane design characteristics associated with the cargo compartment fire protection capabilities for all cargo compartments that are separated from the flight deck to all known operators of such aeroplanes.
The information made available in accordance with points (a) and (b) shall be sufficiently detailed to support operators when conducting a risk assessment for the transportation of goods in the cargo compartment.
The information shall be contained in appropriate aeroplane documentation made available to operators and easily identifiable by the operators’ personnel responsible for conducting the risk assessment.
The design approval holder, who is required to make available the information in accordance with point (a) or (b), shall also make available changes to this information to all known operators of the aeroplanes affected by the change.
Operators of large aeroplanes used in commercial air transport shall ensure that an appropriate landing gear aural warning device is installed in order to significantly reduce the likelihood of landings with landing gear inadvertently retracted.
Operators of large aeroplanes shall minimise the risk of a tyre being below its minimum serviceable inflation pressure during operation.
Operators of large aeroplanes used in commercial air transport shall ensure that every large aeroplane for which the first individual certificate of airworthiness is issued on or after 1 July 2026, is equipped with a runway overrun awareness and alerting system.
This system shall be designed in a manner allowing to reduce the risk of a longitudinal runway excursion during landing by providing an alert, in-flight and on the ground, to the flight crew when the aeroplane is at risk of not being able to stop within the available distance to the end of the runway.
Operators of large aeroplanes used in commercial air transport shall ensure that flight crew compartment door operating systems, where installed, be provided with alternate opening means in order to facilitate access by cabin crew members into the flight crew compartment in the case of a single flight crew member incapacitation.
A holder of a TC or a restricted TC for a large aeroplane certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, shall establish a continuing structural integrity programme for ageing aeroplane structures, which shall comply with the requirements set out in points 26.301 to 26.309.
Point (a) shall not apply to a large aeroplane model which was issued with a TC before 26 February 2021 and which meets any of the following conditions:
it is listed in Table A.1 of Appendix 1 to this Annex;
it is not operated anymore after 26 February 2021;
it has not been certified to conduct civil operation with a payload or passengers;
it has a restricted TC issued before 26 February 2021 in accordance with damage tolerance requirements, provided that it is not operated beyond 75 % of its design service goal and is primarily operated in support of the approval holder’s manufacturing operation;
it is certified with a restricted TC and is designed primarily for firefighting.
The exceptions provided for in points (b)(ii) to (v) shall apply only after the holder of a TC or a restricted TC submitted to the Agency before 27 May 2021 for approval a list identifying the aeroplane type and models, variations or serial numbers together with information supporting the reasons why the aeroplane has been included in the list.
For a large aeroplane model which was issued with a first type certificate before 26 February 2021 and for which an existing change or repair is not and will not be incorporated in any aeroplane in operation on or after 26 February 2022, points (a)(ii) and (iii) of point 26.307 and point 26.308(a)(ii) shall not apply if before 26 February 2022 the holder of a TC or a restricted TC submitted to the Agency for approval the list of all changes and repairs.
A holder of a TC or a restricted TC for a large aeroplane certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, shall:
establish a compliance plan for continuing structural integrity that describes the planned demonstration of compliance with the requirements set out in points 26.302 to 26.309;
submit the compliance plan for continuing structural integrity referred in paragraph (i) to the Agency before 27 May 2021 for approval.
An applicant for a TC or restricted TC referred to in letter (c) of Article 1 paragraph 2 shall:
establish a compliance plan for continuing structural integrity that describes the planned demonstration of compliance with the requirements set out in points 26.303 to 26.306;
submit the compliance plan for continuing structural integrity referred to in paragraph (i) to the Agency before 27 May 2021 or, before the issuance of the certificate, if it occurs later, for approval.
A holder of a TC or a restricted TC, for a large aeroplane certified to carry 30 passengers or more, or with a payload capacity of 3402 kg (7500 lb) or more, certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, shall carry out a fatigue and damage tolerance evaluation of the aeroplane structure and develop the DTI that will prevent catastrophic failures due to fatigue throughout the operational life of the aeroplane.
Unless the documentation describing the DTI referred to in paragraph (a) have already been approved by the Agency in accordance with Annex I (Part 21) to Regulation (EU) No 748/2012, the holder of a TC or a restricted TC shall submit that documentation to the Agency before 26 February 2023 for approval.
A holder of a TC or a restricted TC, for a large aeroplane certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, and certified with a MTOW greater than 34019 kg (75000 lb), shall:
establish a limit of validity (LOV) and include that LOV in an amended ALS;
identify existing and new maintenance actions upon which the LOV depends, and develop service information necessary to implement those maintenance actions and submit the service information for the maintenance actions to the Agency in accordance with a binding schedule agreed with the Agency.
The aeroplane structural configurations to be evaluated for the purpose of establishing the LOV shall include all model variations and derivatives approved under the TC before 26 February 2021 and all structural changes and replacements to the structural configurations of those aeroplanes that are required by an airworthiness directive issued before 26 February 2021.
By way of derogation from point (ii), a holder of a TC or a restricted TC for a large aeroplane shall not be required to develop and submit to the Agency the service information for a maintenance action applicable to a large aeroplane model that will not be operated anymore after the scheduled point of submission for the service information of that maintenance action. For this exception to take effect, the holder of a TC or a restricted TC shall inform the Agency not later than the date on which the aeroplane model ceases operation.
The holder of the TC or the restricted TC shall submit the LOV established in accordance with point (a) and the amendment to the ALS referred to in that point together with the binding schedule to the Agency, before the deadlines established in the following points (i), (ii) and (iii), for approval:
26 August 2022 for a fatigue-critical structure with a certification basis that does not include a damage tolerance evaluation;
26 February 2026 for an aeroplane structure subject to ongoing full-scale fatigue testing on the date of the applicability of this amending Regulation;
26 February 2025 for all other aeroplane structures.
An applicant for a TC or a restricted TC, as referred to in Article 1(2)(c), for a large aeroplane with a MTOW greater than 34019 kg (75000 lb), shall:
establish a LOV and include that LOV in the ALS;
identify existing and new maintenance actions upon which the LOV depends, and develop service information necessary to implement those maintenance actions and submit the service information for the maintenance actions to the Agency in accordance with a binding schedule agreed with the Agency.
The applicant for a TC or a restricted TC, as referred to in Article 1(2), point (c), shall submit the LOV established in accordance with point (c) of this point and the ALS referred to in that point together with the binding schedule to the Agency, for approval:
before the date approved by the Agency in the plan of the applicant for completing tests and analyses of any aeroplane structure requiring new full-scale fatigue testing to support the establishment of the LOV;
before 26 February 2025 for all other aeroplane structures.
A holder of a TC or a restricted TC for a large aeroplane certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, shall establish a baseline corrosion prevention and control programme (CPCP).
Unless the baseline CPCP referred to in point (a) has already been approved by the Agency in accordance with point 21.A.3B(c)(1) of Annex I (Part 21) to Regulation (EU) No 748/2012 or in a maintenance review board report (MRBR) approved by the Agency, the holder of a TC or a restricted TC shall submit the CPCP to the Agency before 26 February 2023, for approval.
An applicant for a TC or a restricted TC, as referred to in Article 1(2), point (c), for a large aeroplane shall establish a baseline CPCP prior to the TC being issued.
A holder of a TC or a restricted TC for a large aeroplane certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, shall establish and implement a process that ensures that the continuing structural integrity programme remains valid throughout the operational life of the aeroplane, taking into account service experience and current operations.
The holder of a TC or a restricted TC shall submit a description of the process referred to in point (a) to the Agency before 26 February 2023 for approval. The holder of a TC or a restricted TC shall implement the process within 6 months after its approval by the Agency.
An applicant for a TC or a restricted TC, as referred to in Article 1(2), point (c), for a large aeroplane, shall establish and implement a process that ensures that the continuing structural integrity programme remains valid throughout the operational life of the aeroplane, taking into account service experience and current operations. It shall submit a description of the process to the Agency before 26 February 2023, or before the issuance of the certificate, whichever occurs later, for approval and shall implement the process within 6 months after its approval by the Agency.
A holder of a TC or a restricted TC for a large aeroplane certified on or after 1 January 1958, for which the application for a TC was submitted before 1 January 2019, and certified to carry 30 passengers or more, or with a payload capacity of 3402 kg (7500 lb) or more, shall identify and list the fatigue-critical baseline structures (FCBS) for all aeroplane model variations and derivatives included in the TC or restricted TC.
The holder of a TC or a restricted TC shall submit the list of the structures referred to in point (a) to the Agency before 26 August 2021, for approval.
Upon approval of the list referred to in point (a) by the Agency, the holder of a TC or a restricted TC shall make it available to the holders of a STC or a major change approval that are required to comply with point 26.330, and to all known operators of such aeroplanes and, on request, to organisations responsible for the management of continuing airworthiness to support the operators that are required to comply with point 26.370.