For the purpose of this Part, the competent authority shall be:
for the oversight of the continuing airworthiness of individual aircraft and the issue of airworthiness review certificates the authority designated by the Member State of registry;
for the oversight of a maintenance organisation as specified in Section A, Subpart F of this Annex (Part-M):
the authority designated by the Member State where that organisation's principle place of business is located;
the Agency if the organisation is located in a third country;
for the approval of aircraft maintenance programmes (‘AMP’), one of the following:
the authority designated by the Member State of registry of the aircraft;
if prior to the approval of the aircraft maintenance programme the Member State of registry agrees, one of the following:
the authority designated by the Member State where the operator has its principal place of business or, in case the operator has no principal place of business, the authority designated by the Member State where the operator has its place of establishment or where the operator resides;
the authority responsible for the oversight of the organisation managing the continuing airworthiness of the aircraft or with which the owner has concluded a limited contract in accordance with point (i)(3) of point M.A.201.
for the oversight of a continuing airworthiness management organisation as specified in Section A, Subpart G of this Annex (Part-M):
the authority designated by the Member State where that organisation's principle place of business is located if the approval is not included in an air operator's certificate;
the authority designated by the Member State of the operator if the approval is included in an air operator's certificate;
the Agency if the organisation is located in a third country.
for the approval of maintenance programmes,
the authority designated by the Member State of registry; or
if agreed with the Member State of registry prior to the approval of the maintenance programme:
the authority designated by the State where the operator has its principal place of business or is established or residing; or
the authority responsible for the oversight of the continuing airworthiness management organisation managing the continuing airworthiness of the aircraft, or with which a limited contract in accordance with M.A.201(i)(3) has been made by the owner.
This Section establishes the measures to be taken to ensure that the airworthiness of aircraft is maintained, including its maintenance. It also specifies the conditions to be met by the persons or organisations involved in such activities.
The owner of the aircraft shall be responsible for the continuing airworthiness of aircraft and shall ensure that no flight takes place unless all of the following requirements are met:
the aircraft is maintained in an airworthy condition;
any operational and emergency equipment fitted is correctly installed and serviceable or clearly identified as unserviceable;
the airworthiness certificate is valid;
the maintenance of the aircraft is performed in accordance with the AMP specified in point M.A.302.
When the aircraft is leased, the responsibilities of the owner are transferred to the lessee if:
the lessee is stipulated on the registration document; or
detailed in the leasing contract.
When reference is made in this Part to the ‘owner’, the term owner covers the owner or the lessee, as applicable.
Any person or organisation performing maintenance shall be responsible for the tasks performed.
The pilot-in-command or, in the case of aircraft used by air carriers licensed in accordance with Regulation (EC) No 1008/2008, the operator, shall be responsible for the satisfactory accomplishment of the pre-flight inspection. That inspection shall be carried out by the pilot or another qualified person and shall not need to be carried out by an approved maintenance organisation or by certifying staff.
In the case of aircraft used by air carriers licensed in accordance with Regulation (EC) No 1008/2008 [Regulation (EC) No 1008/2008 of the European Parliament and of the Council of 24 September 2008 on common rules for the operation of air services in the Community (OJ L 293, 31.10.2008, p. 3).] the operator shall be responsible for the continuing airworthiness of the aircraft it operates and shall:
ensure that no flight takes place unless the conditions set out in point (a) are met;
take the necessary steps to ensure its approval as a continuing airworthiness management organisation (‘CAMO’) pursuant to Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), as part of air operator certificate for the aircraft it operates;
take the necessary steps to ensure its approval in accordance with Annex II (Part-145) or conclude a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with an organisation which has been approved in accordance with Annex II (Part-145).
By derogation to point (e)(2), at least two operators forming part of a single air carrier business grouping may use the same CAMO to assume the responsibility for the continuing airworthiness management of all the aircraft they operate, provided that all of the following requirements are met:
the CAMO is approved in accordance with Annex Vc (Part-CAMO) for the aircraft to be managed;
the CAMO forms part of the same air carrier business grouping as the operators concerned;
a contract is established in accordance with Appendix I to this Annex between the CAMO and the AOC holder not itself approved as a CAMO;
the CAMO has its principal place of business in the territory to which the Treaties apply;
the individual management systems of the organisations concluding a contract are harmonised with each other.
By derogation to point (e)(2), when the termination or revocation of an air operator certificate results in a situation where an air carrier licensed in accordance with Regulation (EC) No 1008/2008 and forming part of an air carrier business grouping is no longer in compliance with point M.A.201(ea), that licensed air carrier shall define and implement an action plan to the satisfaction of the competent authority to comply with point M.A.201(e)(2) as soon as practicable.
For complex motor-powered aircraft used for commercial specialised operations, for CAT operations other than those performed by air carriers licensed in accordance with Regulation (EC) No 1008/2008 or by commercial Approved Training Organisations (‘ATO’) and Declared Training Organisations (‘DTO’) referred to in Article 10a of Regulation (EU) No 1178/2011 [Commission Regulation (EU) No 1178/2011 of 3 November 2011 laying down technical requirements and administrative procedures related to civil aviation aircrew pursuant to Regulation (EC) No 216/2008 of the European Parliament and of the Council (OJ L 311, 25.11.2011, p. 1).], the operator shall ensure that:
no flight takes place unless the conditions set out in point (a) are met;
the tasks associated with continuing airworthiness are performed by a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M); when the operator is not a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), it shall conclude a written contract as regards the performance of those tasks in accordance with Appendix I to this Annex with an organisation approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M);
the CAMO referred to in point (2) is approved in accordance with Annex II (Part-145) as an organisation to qualify for the issue of an approval for the maintenance of aircraft and of components for installation thereon, or that CAMO has concluded a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with organisations approved in accordance with Annex II (Part-145).
For complex motor-powered aircraft not included in points (e) and (f), the owner shall ensure that:
no flight takes place unless the conditions set out in point (a) are met;
the tasks associated with continuing airworthiness are performed by a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M); when the owner is not a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), it shall conclude a written contract as regards the performance of those tasks in accordance with Appendix I to this Annex with an organisation approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M);
the CAMO referred to in point (2) is approved in accordance with Annex II (Part-145) as an organisation to qualify for the issue of an approval for the maintenance of aircraft and of components for installation thereon, or that CAMO has concluded a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with organisations approved in accordance with Annex II (Part-145).
For aircraft other than complex motor-powered aircraft used for commercial specialised operations or for CAT operations other than those performed by air carriers licensed in accordance with Regulation (EC) No 1008/2008, or by commercial ATOs and commercial DTOs referred to in Article 10a of Regulation (EU) No 1178/2011, the operator shall ensure that:
no flight takes place unless the conditions set out in point (a) are met;
the tasks associated with continuing airworthiness are performed by a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), or a combined airworthiness organisation (‘CAO’) approved in accordance with Annex Vd (Part-CAO); when the operator is not a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), or a CAO approved in accordance with Annex Vd (Part-CAO), it shall conclude a written contract in accordance with Appendix I to this Annex with a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), or a CAO approved in accordance with Annex Vd (Part-CAO);
the CAMO or CAO referred to in point (2) is approved in accordance with Annex II (Part-145) or in accordance with Subpart F of this Annex (Part-M) or as a CAO with maintenance privileges, or that CAMO or CAO has concluded a written contract with organisations approved in accordance with Annex II (Part-145) or in accordance with Subpart F of this Annex (Part-M) or Annex Vd (Part-CAO) with maintenance privileges.
For aircraft other than complex motor-powered aircraft not included in points (e) and (h), or used for limited operations, the owner shall ensure that flight takes place only if the conditions set out in point (a) are met. To that end, the owner shall:
attribute the continuing airworthiness tasks referred to in point M.A.301 to a CAMO or CAO through a written contract concluded in accordance with Appendix I; or
carry out those tasks himself; or
carry out those tasks himself except the tasks of the development of and the processing of the approval of the AMP, only if those tasks are performed by a CAMO or CAO through a limited contract concluded in accordance with point M.A.302.
The owner/operator shall ensure that any person authorised by the competent authority is granted access to any of its facilities, aircraft or documents related to its activities, including any subcontracted activities, to determine compliance with this Part.
Where an aircraft included in an air operator certificate is used for non-commercial operations or specialised operations under point ORO.GEN.310 of Annex III or point NCO.GEN.104 of Annex VII to Regulation (EU) No 965/2012, the operator shall ensure that the tasks associated with continuing airworthiness are performed by the CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M) or the combined airworthiness organisation (‘CAO’) approved in accordance with Annex Vd (Part-CAO), whichever applicable, of the air operator certificate holder.
The following persons shall report any safety-related event or identified condition of an aircraft or component that endangers or, if not corrected or addressed, could endanger an aircraft, its occupants or any other person:
the owner carrying out the aircraft continuing airworthiness tasks themselves in accordance with points M.A.201(i)(2) and (3);
the independent certifying staff referred to in point M.A.801(b)(1);
the pilot-owner referred to in point M.A.801(b)(2).
Reports required by point (a) shall:
be made to the competent authority of the Member State of registry of the aircraft and to the organisation responsible for the design of the aircraft or component;
be made as soon as practicable, but in any case, within 72 hours of becoming aware of the event or condition, unless exceptional circumstances prevent this;
be made in a form and manner established by the competent authority of the Member State of registry of the aircraft;
contain all pertinent information about the event or condition known to the person.
In addition to the requirements set out in points (a) and (b), a person maintaining the aircraft shall also report any such event or condition affecting the aircraft to the person or organisation responsible in accordance with point M.A.201 for the continuing airworthiness of such aircraft.
The aircraft continuing airworthiness and the serviceability of operational and emergency equipment shall be ensured by:
the accomplishment of pre-flight inspections;
the rectification of any defect and damage affecting safe operation in accordance with data specified in points M.A.304 and M.A.401, as applicable, while taking into account the minimum equipment list (‘MEL’) and configuration deviation list, when they exist;
the accomplishment of all maintenance in accordance with the AMP referred to in point M.A.302;
the release of all maintenance in accordance with Subpart H;
for all complex motor-powered aircraft or aircraft used by air carriers licensed in accordance with Regulation (EC) No 1008/2008, the analysis of the effectiveness of the approved AMP referred to in point M.A.302;
the accomplishment of any applicable:
airworthiness directive (AD);
operational directive with a continuing airworthiness impact;
continuing airworthiness requirement established by the Agency;
measures required by the competent authority in immediate reaction to a safety problem;
the accomplishment of modifications and repairs in accordance with point M.A.304;
delivering to the pilot-in-command, or to the operator in the case of air carriers licensed in accordance with Regulation (EC) No 1008/2008, the mass and balance statement reflecting the current configuration of the aircraft;
maintenance check flights, when necessary.
Maintenance of each aircraft shall be organised in accordance with an AMP.
The AMP and any subsequent amendments thereto shall be approved by the competent authority.
When the continuing airworthiness of aircraft is managed by a CAMO or CAO, or when there is a limited contract between the owner and a CAMO or CAO concluded in accordance with point M.A.201(i)(3), the AMP and its amendments may be approved through an indirect approval procedure.
In that case, the indirect approval procedure shall be established by the CAMO or CAO concerned as part of the continuing airworthiness management exposition (‘CAME’) referred to in point CAMO.A.300 of Annex Vc or point M.A.704 of this Annex, or as part of the combined airworthiness exposition (‘CAE’) referred to in point CAO.A.025 of Annex Vd and shall be approved by the competent authority responsible for that CAMO or CAO.
The indirect approval procedure shall only be used when the CAMO or CAO concerned is under the oversight of the Member State of registry of aircraft, unless a written contract has been concluded in accordance with point 3 of point M.1 transferring responsibility for the approval of the aircraft maintenance programme to the competent authority responsible for the CAMO or CAO.
The AMP shall demonstrate compliance with:
the instructions issued by the competent authority;
the instructions for continuing airworthiness:
issued by the holders of the type certificate, restricted type certificate, supplemental type certificate, major repair design approval, ETSO authorisation or the declarant of a declaration of design compliance or the holder of any other relevant approval issued under Annex I (Part 21) or, as applicable, Annex Ib (Part 21 Light) to Regulation (EU) No 748/2012;
included in the certification specifications referred to in point 21.A.90B or 21.A.431B of Annex I (Part 21) to Regulation (EU) No 748/2012, if applicable;
included in the certification specifications referred to in point 21L.A.62, 21L.A.102, 21L.A.202 or 21L.A.222 of Annex Ib (Part 21 Light) to Regulation (EU) No 748/2012, if applicable.
By derogation to point (d), the owner or the organisation managing the continuing airworthiness of the aircraft may deviate from the instruction referred to in point (d)(2) and propose escalated intervals in the AMP, based on data obtained from sufficient reviews carried out in accordance with point (h). Indirect approval is not permitted for the escalation of safety-related tasks. The owner or the organisation managing the continuing airworthiness of the aircraft may also propose additional instructions in the AMP.
The AMP shall contain details of all maintenance to be carried out, including frequency and any specific tasks linked to the type and specificity of operations.
For complex motor-powered aircraft, when the AMP is based on maintenance steering group logic or on condition monitoring, the AMP shall include a reliability programme.
The AMP shall be subject to periodic reviews and be amended accordingly when necessary. Those reviews shall ensure that the AMP continues to be up to date and valid in light of the operating experience and instructions from the competent authority, while taking into account new or modified maintenance instructions issued by the type-certificate and supplemental type-certificate holders, declarant of a declaration of design compliance and any other organisation that publishes such data in accordance with Annex I (Part 21) or, as applicable, Annex Ib (Part 21 Light) to Regulation (EU) No 748/2012.
Any applicable airworthiness directive must be carried out within the requirements of that airworthiness directive, unless otherwise specified by the Agency.
A person or organisation repairing an aircraft or a component, shall assess any damage. Modifications and repairs shall be carried out using, as appropriate, the following data:
approved by the Agency;
approved by a design organisation complying with Annex I (Part 21) to Regulation (EU) No 748/2012;
contained in the requirements referred to in point 21.A.90B or 21.A.431B of Annex I (Part 21) to Regulation (EU) No 748/2012;
contained in the requirements referred to in point 21L.A.62, 21L.A.102, 21L.A.202 or 21L.A.222 of Annex Ib (Part 21 Light) to Regulation (EU) No 748/2012;
declared by a declarant of a declaration of design compliance complying with Annex Ib (Part 21 Light) to Regulation (EU) No 748/2012.
At the completion of any maintenance, aircraft certificate of release to service (‘CRS’) required by point M.A.801 or point 145.A.50, as applicable, shall be entered in the aircraft continuing airworthiness record system, as soon as practicable and no later than 30 days after the completion of any maintenance.
The aircraft continuing airworthiness record system shall contain the following:
the date of the entry, the total in-service life accumulated in the applicable parameter for aircraft, engine(s) and/or propeller(s);
the aircraft continuing airworthiness records described in points (c) and (d) below together with the supporting detailed maintenance records described in point (e) below;
if required by point M.A.306, the aircraft technical log.
The aircraft continuing airworthiness records shall include the current mass and balance report and the current status of:
ADs and measures mandated by the competent authority in immediate reaction to a safety problem;
modifications and repairs;
compliance with the AMP;
deferred maintenance tasks and deferred defects rectification.
The aircraft continuing airworthiness records shall include the current status specific to components of:
life-limited parts, including the life accumulated by each affected part in relation to the applicable airworthiness limitation parameter; and
time-controlled components, including the life accumulated by the affected components in the applicable parameter, since the last accomplishment of scheduled maintenance, as specified in the AMP.
The owner or operator shall establish a system to keep the following documents and data in a form acceptable to the competent authority and for the periods specified below:
aircraft technical log system: the technical log or other data equivalent in scope and detail, covering the 36 months period prior to the last entry,
the CRS and detailed maintenance records:
demonstrating compliance with ADs and measures mandated by the competent authority in immediate reaction to a safety problem applicable to the aircraft, engine(s), propeller(s) and components fitted thereto, as appropriate, until such time as the information contained therein is superseded by new information equivalent in scope and detail but covering a period not shorter than 36 months;
demonstrating compliance with the applicable data in accordance with point M.A.304 for current modifications and repairs to the aircraft, engine(s), propeller(s) and any component subject to airworthiness limitations; and
of all scheduled maintenance or other maintenance required for continuing airworthiness of aircraft, engine(s), propeller(s), as appropriate, until such time as the information contained therein is superseded by new information equivalent in scope and detail but covering a period not shorter than 36 months.
data specific to certain components:
an in-service history record for each life-limited part based on which the current status of compliance with airworthiness limitations is determined;