Annex I to Regulation (EU) No 965/2012 is amended as follows:
The title is replaced by ‘Definitions for terms used in Annexes II to VIII’.
The following item is inserted:
‘(11a) “Balloon empty mass” means the mass determined by weighing the balloon with all the installed equipment a specified in the AFM.’.
Point 40 is replaced by the following:
‘(40) “Dry lease agreement” means an agreement between undertakings pursuant to which the aircraft is operated under the air operator certificate (AOC) of the lessee or, in the case of commercial operations other than CAT, under the responsibility of the lessee.’.
The following item is inserted:
‘(117a) “Task specialist” means a person assigned by the operator or a third party, or acting as an undertaking, who performs tasks on the ground directly associated with a specialised task or performs specialised tasks on board or from the aircraft.’.
Point 120 is replaced by the following:
‘(120) “Traffic load” means the total mass of passengers, baggage, cargo and carry-on specialist equipment and, except for balloons, including any ballast.’.
Point 127 is replaced by the following:
‘(127) “Wet lease agreement” means an agreement:
in the case of CAT operations, between air carriers pursuant to which the aircraft is operated under the AOC of the lessor; or
in the case of commercial operations other than CAT, between operators pursuant to which the aircraft is operated under the responsibility of the lessor.’.
Annex II to Regulation (EU) No 965/2012 is amended as follows:
In ARO.GEN.120(d)(1), a comma and the words ‘specialised operation authorisation’ are inserted after ‘the approval’.
In ARO.GEN.200(c), the words ‘or authorised’ are inserted after ‘certified’.
ARO.GEN.205(a), a comma and the words ‘specialised operation authorisation’ are inserted after ‘the initial certification’.
ARO.GEN.205(b), a comma and the word ‘authorisation’ are inserted after ‘certification’.
In ARO.GEN.220(a):
the following item is inserted:
‘(4a) the process of authorisation of a high risk commercial specialised operation and continuing oversight of an authorisation holder;’;
point (7) is replaced by the following
‘(7) oversight of persons and organisations exercising activities within the territory of the Member State, but overseen, certified or authorised by the competent authority of another Member State or the Agency, as agreed between these authorities;’;
in point (9), a comma and the words ‘or authorisation’ are inserted after ‘certification’.
In ARO.GEN.220, point (b) is replaced by the following:
‘(b) The competent authority shall maintain a list of all organisation certificates and specialised operations authorisations it issued as well as declarations it received’.
In ARO.GEN.300(a), items (1) and (2) are replaced by the following:
‘(1) compliance with the requirements applicable to organisations or type of operations prior to the issue of a certificate, approval or authorisation, as applicable;
continued compliance with the applicable requirements of organisations it has certified, specialised operations it has authorised and organisations from whom it received a declaration;’.
In ARO.GEN.305, the following amendments are made:
point (d) is replaced by the following:
‘(d) For organisations declaring their activity to the competent authority, the oversight programme shall be based on the specific nature of the organisation, the complexity of its activities and the data of past oversight activities and the assessment of risks associated with the type of activity carried out. It shall include audits and inspections, including ramp and unannounced inspections, as appropriate.’;
point (d1) is inserted as follows:
‘(d1) For organisations holding a specialised operations authorisation, the oversight programme shall be established in accordance with (d) and shall also take into account the past and current authorisation process and the validity period of the authorisation.’.
ARO.GEN.350(b) is replaced by the following:
‘(b) A level 1 finding shall be issued by the competent authority when any significant non-compliance is detected with the applicable requirements of Regulation (EC) No 216/2008 and its Implementing Rules, with the organisation’s procedures and manuals or with the terms of an approval, certificate, specialised operation authorisation or with the content of a declaration which lowers safety or seriously hazards flight safety.’.
In ARO.GEN.350(b)(2) and (3) respectively, the words ‘or specialised operations authorisation’ are inserted after the words ‘organisation certificate’.
ARO.GEN.350(c) is replaced by the following:
‘(c) A level 2 finding shall be issued by the competent authority when any non-compliance is detected with the applicable requirements of Regulation (EC) No 216/2008 and its Implementing Rules, with the organisation’s procedures and manuals or with the terms of an approval, certificate, specialised operation authorisation or with the content of a declaration which could lower safety or hazard flight safety.’.
In ARO.GEN.350(d)(1), a comma and the words ‘specialised operations authorisation’ are inserted after ‘certificate’.
In ARO.GEN.350(e), a comma and the words ‘or authorised by’ are inserted after the words ‘an organisation certified by’.
In ARO.GEN.355(a), the reference to Regulation (EU) No 290/2012 is replaced by a reference to Regulation (EU) No 1178/2011.
The following ARO.GEN.360 is added:
If, during oversight or by any other means, evidence is found showing a non-compliance with the applicable requirements by an operator subject to the requirements laid down in Regulation (EC) No 216/2008 and its Implementing Rules, the competent authority that identified the non-compliance shall take any enforcement measures necessary to prevent the continuation of that non-compliance.’
In ARO.OPS.100, the following point (c) is added:
‘(c) The competent authority may determine specific operational limitations. Such limitations shall be documented in the operations specifications.’.
In SUBPART OPS the following SECTION Ia is inserted:
Upon receiving an application for the issue of a high risk commercial specialised operations authorisation, the competent authority of the operator shall review the operator’s risk assessment documentation and standard operating procedures (SOP), related to one or more planned operations and developed in accordance with the relevant requirements of Annex VIII (Part-SPO).
When satisfied with the risk assessment and SOP, the competent authority of the operator shall issue the authorisation, as established in Appendix VI. The authorisation may be issued for a limited or an unlimited duration. The conditions under which an operator is authorised to conduct one or more high risk commercial specialised operations shall be specified in the authorisation.
Upon receiving an application for a change to the authorisation, the competent authority of the operator shall comply with (a) and (b). It shall prescribe the conditions under which the operator may operate during the change, unless the competent authority determines that the authorisation needs to be suspended.
Upon receiving an application for the renewal of the authorisation, the competent authority of the operator shall comply with (a) and (b). It may take into account the past authorisation process and oversight activities.
Without prejudice to any additional enforcement measures, when the operator implements changes without having submitted an amended risk assessment and SOP, the competent authority of the operator shall suspend, limit or revoke the authorisation.
Upon receiving an application for the issue of an authorisation for a cross-border high risk commercial specialised operation, the competent authority of the operator shall review the operator’s risk assessment documentation and standard operating procedures (SOP) in coordination with the competent authority of the place where the operation is planned to be conducted. When both authorities are satisfied with the risk assessment and SOP, the competent authority of the operator shall issue the authorisation.
The competent authority shall approve a lease agreement involving a third country registered aircraft or a third country operator when the SPO operator has demonstrated compliance with ORO.SPO.100.
The approval of a dry lease-in agreement shall be suspended or revoked whenever the certificate of airworthiness of the aircraft is suspended or revoked.’.
In ARO.OPS.200(b)(2), the words ‘and specialised operations’ are inserted after the words ‘non-commercial operations’.
ARO.OPS.210 is replaced by the following:
The competent authority may determine a distance or local area for the purpose of operations.’.
In Subpart OPS the following SECTION III is inserted:
The competent authority may establish additional conditions for introductory flights carried out in accordance with Part-NCO in the territory of the Member State. Such conditions shall ensure safe operations and be proportionate.’.
In Appendix I:
the sub-title is replaced by ‘(Approval schedule for air transport operators)’;
the words ‘Commercial specialised operations (SPO)’ and footnote 2 are deleted.
In Appendix II, the repeating word ‘Take-off’ is deleted and footnote 10 is replaced by the following:
‘(10) Insertion of applicable precision approach category: LTS CAT I, CAT II, OTS CAT II, CAT IIIA, CAT IIIB or CAT IIIC. Insertion of minimum runway visual range (RVR) in meters and decision height (DH) in feet. One line is used per listed approach category.’.
In Appendix V, the words ‘Specialised operations’ are added below the words ‘Non-commercial operations’.
The following Appendix VI is added:
Annex III to Regulation (EU) No 965/2012 is amended as follows:
All references to Regulation (EC) No 1702/2003 are replaced by references to Commission Regulation (EU) No 748/2012 [Commission Regulation (EU) No 748/2012 of 3 August 2012 laying down implementing rules for the airworthiness and environmental certification of aircraft and related products, parts and appliances, as well as for the certification of design and production organisations (OJ L 224, 21.8.2012, p. 1).].
All references to Regulation (EC) No 290/2012 are replaced by references to Regulation (EU) No 1178/2011.
The text of ORO.GEN.005 is replaced by the following:
‘This Annex establishes requirements to be followed by an air operator conducting:
commercial air transport operations (CAT);
commercial specialised operations;
non-commercial operations with complex motor-powered aircraft;
non-commercial specialised operations with complex motor-powered aircraft.’.
In ORO.GEN.105, the words ‘or specialised operation authorisation’ are inserted after ‘declaration obligation’.
In ORO.GEN.110, point (a) is replaced by the following:
‘(a) The operator is responsible for the operation of the aircraft in accordance with Annex IV to Regulation (EC) No 216/2008, as applicable, the relevant requirements of this Annex and its air operator certificate (AOC) or specialised operation authorisation (SPO authorisation) or declaration.’.
In ORO.GEN.110(c), a comma and the words ‘SPO authorisation’ are inserted after the word ‘certificate’.
In ORO.GEN.110, the following point is added:
‘(k) Notwithstanding (j), the operator of a sailplane or a balloon or of flights taking off and landing at the same aerodrome or operating site, under VFR by day, with
single-engined propeller-driven aeroplanes having a maximum certified take-off mass of 5700 kg or less and a MOPSC of 5 or less; or
other than complex motor-powered helicopters, single-engined, with a MOPSC of 5 or less,
shall ensure that the flight crew has received an appropriate training or briefing to enable them to recognise undeclared dangerous goods brought on-board by passengers or as cargo.’.
In ORO.GEN.115:
the title is replaced by the following: ‘Application for an AOC’;
in point (a) the word ‘air’ is inserted before ‘operator certificate’.
In ORO.GEN.120, the following point is added:
‘(d) When an operator subject to SPO authorisation wishes to use alternative means of compliance, it shall comply with (b) whenever such alternative means of compliance affects the standard operating procedures that are part of the authorisation and with (c) for the declared part of its organisation and operation.’.
The title of ORO.GEN.125 is replaced by the following: ‘Terms of approval and privileges of an AOC holder’.
The title of ORO.GEN.130 is replaced by the following: ‘Changes related to an AOC holder’.
The title of ORO.GEN.135 is replaced by the following: ‘Continued validity of an AOC’.
In ORO.GEN.140(a), a comma and the words ‘SPO authorisation’ are inserted after the word ‘certification’.
In ORO.GEN.140(b), the words ‘in the case of CAT’ are inserted, surrounded by commas, after the words ‘Access to the aircraft mentioned under (a) shall’.
ORO.GEN.205 is replaced by the following:
The operator shall ensure that when contracting or purchasing any part of its activity, the contracted or purchased service or product conforms to the applicable requirements.
When the certified operator or the SPO authorisation holder contracts any part of its activity to an organisation that is not itself certified or authorised in accordance with this Part to carry out such activity, the contracted organisation shall work under the approval of the operator. The contracting organisation shall ensure that the competent authority is given access to the contracted organisation, to determine continued compliance with the applicable requirements.’.
In ORO.AOC.100(a), the word ‘transport’ is inserted before the word ‘operations’.
In ORO.AOC.100, points (b) and (c) are replaced by the following:
‘(b) The operator shall provide the following information to the competent authority:
the official name and business name, address, and mailing address of the applicant;
a description of the proposed operation, including the type(s), and number of aircraft to be operated;
a description of the management system, including organisational structure;
the name of the accountable manager;
the names of the nominated persons required by ORO.AOC.135(a) together with their qualifications and experience;
a copy of the operations manual required by ORO.MLR.100;
a statement that all the documentation sent to the competent authority have been verified by the applicant and found in compliance with the applicable requirements.
Applicants shall demonstrate to the competent authority that:
they comply with all the applicable requirements of Annex IV to Regulation (EC) No 216/2008, this Annex, Annex IV (Part-CAT) and Annex V (Part-SPA) to this Regulation;
all aircraft operated have a certificate of airworthiness (CofA) in accordance with Regulation (EU) No 748/2012; and
its organisation and management are suitable and properly matched to the scale and scope of the operation.’.
In ORO.AOC.125(a)(1)(ii), the words ‘air transport’ are inserted after the word ‘commercial’.
In ORO.DEC.100, the first sentence is replaced by the following:
‘The operator of complex motor-powered aircraft engaged in non-commercial operations or non-commercial specialised operations, and the commercial specialised operator shall:’.
The following Subpart is inserted after SUBPART DEC — DECLARATION:
A commercial specialised operator shall in addition to ORO.DEC.100 also comply with ORO.AOC.135, ORO.AOC.140 and ORO.AOC.150.
Aircraft shall have a certificate of airworthiness (CofA) in accordance with Regulation (EU) No 748/2012 or shall be leased-in in accordance with (c).
A commercial specialised operator shall obtain prior approval of the competent authority and comply with the following conditions, if:
Wet leasing-in an aircraft of a third country operator:
The safety standards of a third country operator with regard to continuing airworthiness and air operations are equivalent to the applicable requirements established by Regulation (EC) No 2042/2003 and this Regulation;
The aircraft of a third country operator has a standard CofA issued in accordance with ICAO Annex 8;
The duration of the wet lease-in does not exceed seven months in any 12 consecutive month period; or
Dry leasing-in an aircraft registered in a third country:
An operational need has been identified that cannot be satisfied through leasing an aircraft registered in the EU;
The duration of the dry lease-in does not exceed seven months in any 12 consecutive month period;
Compliance with the applicable requirements of Regulation (EC) No 2042/2003 is ensured;
The aircraft is equipped in accordance with Annex VIII [Part SPO].
A commercial specialised operator shall apply for and obtain an authorisation issued by the competent authority of the operator prior to commencing a high risk commercial specialised operation:
that is carried out over an area where the safety of third parties on the ground is likely to be endangered in the event of an emergency, or
that, as determined by the competent authority of the place where the operation is conducted, due to its specific nature and the local environment in which it is conducted, poses a high risk, in particular to third parties on the ground.
The operator shall provide the following information to the competent authority:
the official name and business name, address, and mailing address of the applicant;
a description of the management system, including organisational structure;
a description of the proposed operation, including the type(s), and number of aircraft to be operated;
the risk assessment documentation and related standard operating procedures, required by SPO.OP.230;
a statement that all the documentation sent to the competent authority has been verified by the operator and found in compliance with the applicable requirements.
The application for an authorisation or its amendment shall be made in a form and manner established by the competent authority, taking into account the applicable requirements of Regulation (EC) No 216/2008 and its Implementing Rules.
Any change affecting the scope of the authorisation or the authorised operations shall require prior approval of the competent authority. Any change not covered by the initial risk assessment, shall require the submission of an amended risk assessment and SOP to the competent authority.
The application for approval of a change shall be submitted before any such change takes place, in order to enable the competent authority to determine continued compliance with Regulation (EC) No 216/2008 and its Implementing Rules and to amend, if necessary, the authorisation. The operator shall provide the competent authority with any relevant documentation.
The change shall only be implemented upon receipt of formal approval by the competent authority in accordance with ARO.OPS.150.
The operator shall operate under the conditions prescribed by the competent authority during such changes, as applicable.
An operator holding a specialised operation authorisation shall comply with the scope and privileges defined in the authorisation.
The operator’s authorisation shall remain valid subject to:
the operator remaining in compliance with the relevant requirements of Regulation (EC) No 216/2008 and its Implementing Rules, taking into account the provisions related to the handling of findings as specified under ORO.GEN.150;
the competent authority being granted access to the operator as defined in ORO.GEN.140 to determine continued compliance with the relevant requirements of Regulation (EC) No 216/2008 and its Implementing Rules; and
the authorisation not being surrendered or revoked.
Upon revocation or surrender the authorisation shall be returned to the competent authority without delay.’.
ORO.MLR.100(b) is replaced by the following:
‘(b) The content of the OM shall reflect the requirements set out in this Annex, Annex IV (Part-CAT), Annex V (Part-SPA), Annex VI (Part-NCC) and Annex VIII (Part-SPO), as applicable, and shall not contravene the conditions contained in the operations specifications to the air operator certificate (AOC), the SPO authorisation or the declaration and the list of specific approvals, as applicable.’.
In ORO.MLR.100, the following point (g1) is inserted:
‘(g1) For SPO authorisation holders, any amendment associated with the authorised standard operating procedures, prior approval shall be obtained before the amendment becomes effective.’
In ORO.MLR.100(h), the words ‘and (g1)’ are inserted after ‘Notwithstanding (g)’.
In ORO.MLR.101, the first sentence is replaced by the following:
‘Except for operations with single engined propeller-driven aeroplanes with a MOPSC of 5 or single engined non-complex helicopters with a MOPSC of 5, taking off and landing at the same aerodrome or operating site, under VFR by day, and for operations with sailplanes and balloons, the main structure of the OM shall be as follows:’.
ORO.MLR.115(a) is replaced by the following:
‘(a) The following records shall be stored for at least 5 years.
for CAT operators, records of the activities referred to in ORO.GEN.200;
for declared operators, a copy of the operator’s declaration, details of approvals held and operations manual;
for SPO authorisation holders, in addition to (a)(2), records related to the risk assessment conducted in accordance with SPO.OP.230 and related standard operating procedures.’
In ORO.MLR.115(b)(4), a comma and the words ‘if applicable’ are added after ‘dangerous goods’.
In ORO.SEC.100.A the title is replaced by the followings
In ORO.SEC.100.H, the title is replaced by the following
ORO.FC.005 is replaced by the following:
This Subpart establishes requirements to be met by the operator related to flight crew training, experience and qualification and comprises:
SECTION 1 specifying common requirements applicable to both non-commercial operations of complex motor-powered aircraft and any commercial operation;
SECTION 2 specifying additional requirements applicable to commercial air transport operations, with the exception of:
commercial air transport operations of sailplanes or balloons; or