ANNEX I, Directive (EU) 2014/45

In forcesince 20 May 2023cited 1×

This Annex identifies the vehicle systems and components to be tested; it details the recommended methods for testing them and the criteria to be used when determining whether the condition of the vehicle is acceptable.

The test must cover at least the items listed in point 3 below provided that these relate to the equipment of the vehicle being tested in the Member State concerned. The test may also include a verification as to whether the relevant parts and components of that vehicle correspond to the required safety and environmental characteristics that were in force at the time of approval or, if applicable, at the time of retrofitting.

Where the design of the vehicle does not allow the application of the test methods laid down in this Annex, the test shall be conducted in accordance with the recommended test methods accepted by the competent authorities. The competent authority must be satisfied that safety and environmental standards will be maintained.

Testing of all the items listed below shall be considered as mandatory in the context of a periodic roadworthiness test, with the exception of those marked with the indication ‘X’ which are related to the condition of the vehicle and its suitability for use on the road but which are not considered essential in the context of a roadworthiness test.

The ‘Reasons for failure’ do not apply in cases where they refer to requirements that were not prescribed in the relevant vehicle approval legislation at the time of first registration or first entry into service, or in the retrofitting requirements.

Where a method of testing is indicated as visual, it means that, in addition to looking at the items concerned, the inspector shall also, if appropriate, handle them, evaluate their noise or use any other appropriate means of inspection not involving the use of equipment.

The test shall cover at least the following areas:

(0)

Identification of the vehicle;

(1)

Braking equipment;

(2)

Steering;

(3)

Visibility;

(4)

Lighting equipment and parts of the electrical system;

(5)

Axles, wheels, tyres, suspension;

(6)

Chassis and chassis attachments;

(7)

Other equipment;

(8)

Nuisance;

(9)

Supplementary tests for passenger-carrying vehicles of categories M2 and M3.

The test shall cover at least the items, and use the minimum standards and the recommended methods, listed in the following table.

For each vehicle system and component subject to testing, the assessment of deficiencies shall be carried out in accordance with the criteria set out in that table, on a case-by-case basis.

Deficiencies not listed in this Annex shall be assessed in terms of the risks that they pose to road safety.

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

0.1. Registration number plates (if needed by requirements1)

Visual inspection |

(a)

Number plate(s) missing or so insecurely fixed that it is (they are) likely to fall off.

X |

(b)

Inscription missing or illegible

X |

(c)

Not in accordance with vehicle documents or records.

X |

0.2. Vehicle identification/chassis/serial number

Visual inspection |

(a)

Missing or can not be found.

X |

(b)

Incomplete, illegible, obviously falsified, or does not match the vehicle documents.

X |

(c)

Illegible vehicle documents or clerical inaccuracies.

X | |

1.1.1. Service brake pedal/hand lever pivot

Visual inspection of the components while the braking system is operated.

Note: Vehicles with power-assisted braking systems should be inspected with the engine switched off.

(a)

Pivot too tight.

X |

(b)

Excessive wear or play.

X |

1.1.2. Pedal/hand lever condition and travel of the brake operating device

Visual inspection of the components while the braking system is operated

Note: Vehicles with power-assisted braking systems should be inspected with the engine switched off.

(a)

Excessive or insufficient reserve travel.

X |

(b)

Brake control not releasing correctly.

X | |

If its functionality is affected. | | X |

(c)

Anti-slip provision on brake pedal missing, loose or worn smooth.

X |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.1.3. Vacuum pump or compressor and reservoirs

Visual inspection of the components at normal working pressure. Check time required for vacuum or air pressure to reach safe working value and function of warning device, multi-circuit protection valve and pressure relief valve. |

(a)

Insufficient pressure/vacuum to give assistance for at least four brake applications after the warning device has operated (or gauge shows an unsafe reading);

X |

at least two brake applications after the warning device has operated (or gauge shows an unsafe reading). | | | X

(b)

Time taken to build up air pressure/vacuum to safe working value is too long according to the requirements1

X |

(c)

Multi-circuit protection valve or pressure relief valve not working.

X |

(d)

Air leak causing a noticeable drop in pressure or audible air leaks.

X |

(e)

External damage likely to affect the function of the braking system.

X |

Secondary braking performance not met. | | | X

1.1.4. Low pressure warning gauge or indicator

Functional check | Malfunctioning or defective gauge or indicator. | X | |

Low pressure not identifiable. | | X |

1.1.5. Hand-operated brake control valve

Visual inspection of the components while the braking system is operated. |

(a)

Control cracked, damaged or excessively worn.

X |

(b)

Control insecure on valve or valve insecure.

X |

(c)

Loose connections or leaks in system.

X |

(d)

Unsatisfactory operation.

X |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.1.6. Parking brake activator, lever control, parking brake ratchet, electronic parking brake

Visual inspection of the components while the braking system is operated. |

(a)

Ratchet not holding correctly.

X |

(b)

Wear at lever pivot or in ratchet mechanism.

X | |

Excessive wear. | | X |

(c)

Excessive movement of lever indicating incorrect adjustment.

X |

(d)

Activator missing, damaged or inoperative.

X |

(e)

Incorrect functioning, warning indicator shows malfunction

X |

1.1.7. Braking valves (foot valves, unloaders, governors)

Visual inspection of the components while the braking system is operated. |

(a)

Valve damaged or excessive air leak.

X |

If its functionality is affected. | | | X

(b)

Excessive oil discharge from compressor.

X | |

(c)

Valve insecure or inadequately mounted.

X |

(d)

Hydraulic fluid discharge or leak.

X |

If its functionality is affected. | | | X

1.1.8. Couplings for trailer brakes (electrical & pneumatic)

Disconnect and reconnect braking system coupling between towing vehicle and trailer. |

(a)

Tap or self sealing valve defective.

X | |

If its functionality is affected. | | X |

(b)

Tap or valve insecure or inadequately mounted.

X | |

If its functionality is affected. | | X |

(c)

Excessive leaks.

X |

If its functionality is affected. | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

(d)

Not functioning correctly.

X |

Operation of brake affected. | | | X

1.1.9. Energy storage reservoir pressure tank

Visual inspection. |

(a)

Tank slightly damaged or slightly corroded.

X | |

Tank heavily damaged, corroded or leaking. | | X |

(b)

Drain device operation affected.

X | |

Drain device inoperative. | | X |

(c)

Tank insecure or inadequately mounted.

X |

1.1.10. Brake servo units, master cylinder (hydraulic systems)

Visual inspection of the components while the braking system is operated, if possible. |

(a)

Defective or ineffective servo unit.

X |

If it is not operating. | | | X

(b)

Master cylinder defective but brake still operating.

X |

Master cylinder defective or leaking. | | | X

(c)

Master cylinder insecure but brake still operating.

X |

Master cylinder insecure. | | | X

(d)

Insufficient brake fluid below MIN mark

X | |

Brake fluid significantly below MIN mark | | X |

No brake fluid visible. | | | X

(e)

Master cylinder reservoir cap missing.

X | |

(f)

Brake fluid warning light illuminated or defective.

X | |

(g)

Incorrect functioning of brake fluid level warning device.

X | |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.1.11. Rigid brake pipes

Visual inspection of the components while the braking system is operated, if possible. |

(a)

Imminent risk of failure or fracture.

X

(b)

Pipes or connections leaking (air brake systems).

X |

Pipes or connection leaking (hydraulic brake systems). | | | X

(c)

Pipes damaged or excessively corroded.

X |

Affecting the functioning of the brakes on account of blocking or imminent risk of leaking. | | | X

(d)

Pipes misplaced.

X | |

Risk of damage. | | X |

1.1.12. Flexible brake hoses

Visual inspection of the components while the braking system is operated, if possible. |

(a)

Imminent risk of failure or fracture.

X

(b)

Hoses damaged, chafing, twisted or too short.

X | |

Hoses damaged or chafing. | | X |

(c)

Hoses or connections leaking (air brake systems)

X |

Hoses or connections leaking (hydraulic brake systems). | | | X

(d)

Hoses bulging under pressure.

X |

Cord impaired. | | | X

(e)

Hoses porous.

X |

1.1.13. Brake linings and pads

Visual inspection. |

(a)

Lining or pad excessively worn (minimum mark reached).

X |

Lining or pad excessively worn (minimum mark not visible). | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

(b)

Lining or pad contaminated (oil, grease etc.).

X |

Braking performance affected. | | | X

(c)

Lining or pad missing or wrongly mounted.

X

1.1.14. Brake drums, brake discs

Visual inspection. |

(a)

Drum or disc worn

X |

Drum or disc excessively worn, excessively scored, cracked, insecure or fractured. | | | X

(b)

Drum or disc contaminated (oil, grease, etc.).

X |

Braking performance affected. | | | X

(c)

Drum or disc missing.

X

(d)

Back plate insecure.

X |

1.1.15. Brake cables, rods, levers, linkages

Visual inspection of the components while the braking system is operated, if possible. |

(a)

Cable damaged or knotted.

X |

Braking performance affected. | | | X

(b)

Component excessively worn or corroded.

X |

Braking performance affected. | | | X

(c)

Cable, rod or joint insecure.

X |

(d)

Cable guide defective.

X |

(e)

Restriction to free movement of the braking system.

X |

(f)

Abnormal movement of the levers/linkage indicating maladjustment or excessive wear.

X |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.1.16. Brake actuators (including spring brakes or hydraulic cylinders)

Visual inspection of the components while the braking system is operated, if possible. |

(a)

Actuator cracked or damaged.

X |

Braking performance affected. | | | X

(b)

Actuator leaking.

X |

Braking performance affected. | | | X

(c)

Actuator insecure or inadequately mounted.

X |

Braking performance affected. | | | X

(d)

Actuator excessively corroded.

X |

Likely to crack. | | | X

(e)

Insufficient or excessive travel of operating piston or diaphragm mechanism.

X |

Braking performance affected (lack of reserve movement). | | | X

(f)

Dust cover damaged.

X | |

Dust cover missing or excessively damaged. | | X |

1.1.17. Load sensing valve

Visual inspection of the components while the braking system is operated, if possible. |

(a)

Defective linkage.

X |

(b)

Linkage incorrectly adjusted.

X |

(c)

Valve seized or inoperative (ABS functioning).

X |

Valve seized or inoperative. | | | X

(d)

Valve missing (if required).

X

(e)

Missing data plate.

X | |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

(f)

Data illegible or not in accordance with requirements1

X | |

1.1.18. Slack adjusters and indicators

Visual inspection. |

(a)

Adjuster damaged, seized or having abnormal movement, excessive wear or incorrect adjustment.

X |

(b)

Adjuster defective.

X |

(c)

Incorrectly installed or replaced.

X |

1.1.19. Endurance braking system (where fitted or required)

Visual inspection. |

(a)

Insecure connectors or mountings.

X | |

If its functionality is affected. | | X |

(b)

System obviously defective or missing.

X |

1.1.20. Automatic operation of trailer brakes

Disconnect brake coupling between towing vehicle and trailer. | Trailer brake does not apply automatically when coupling disconnected. | | | X

1.1.21. Complete braking system

Visual inspection |

(a)

Other system devices (e.g. anti-freeze pump, air dryer, etc.) damaged externally or excessively corroded in a way that adversely affects the braking system.

X |

Braking performance affected. | | | X

(b)

Leakage of air or anti-freeze.

X | |

System functionality affected. | | X |

(c)

Any component insecure or inadequately mounted.

X |

(d)

Unsafe modification to any component3

X |

Braking performance affected. | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.1.22. Test connections (where fitted or required)

Visual inspection |

(a)

Missing.

X |

(b)

Damaged.

X | |

Unusable or leaking. | | X |

1.1.23. Overrun brake

Visual inspection and by operation | Insufficient efficiency. | | X |

1.2.1. Performance

During a test on a brake tester or, if impossible, during a road test, apply the brakes progressively up to maximum effort. |

(a)

Inadequate braking effort on one or more wheels.

X |

No braking effort on one or more wheels. | | | X

(b)

Braking effort from any wheel is less than 70 % of the maximum effort recorded from the other wheel on the same axle. Or, in the case of testing on the road, the vehicle deviates excessively from a straight line.

X |

Braking effort from any wheel is less than 50 % of the maximum effort recorded from the other wheel on the same axle in the case of steered axles. | | | X

(c)

No gradual variation in brake effort (grabbing).

X |

(d)

Abnormal lag in brake operation of any wheel.

X |

(e)

Excessive fluctuation of brake force during each complete wheel revolution.

X |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.2.2. Efficiency

Test with a brake tester or, if one cannot be used for technical reasons, by a road test using a deceleration recording instrument to establish the braking ratio which relates to the maximum authorised mass or, in the case of semi-trailers, to the sum of the authorised axle loads.

Vehicles or a trailer with a maximum permissible mass exceeding 3,5 tonnes has to be inspected following the standards given by ISO 21069 or equivalent methods.

Road tests should be carried out under dry conditions on a flat, straight road.

Does not give at least the minimum figure as follows (1):

1.

Vehicles registered for the first time after 1/1/2012:

Category M1: 58 %

Categories M2 and M3: 50 %

Category N1: 50 %

Categories N2 and N3: 50 %

Categories O2, O3 and O4:

for semi-trailers: 45 % (2)

for draw-bar trailers: 50 %

X |

2.

Vehicles registered for the first time before 1/1/2012:

Categories M1, M2 and M3: 50 % (3)

Category N1: 45 %

Categories N2 and N3: 43 % (4)

Categories O2, O3 and O4: 40 % (5)

X |

3.

Other categories

Categories L (both brakes together):

Category L1e: 42 %

Categories L2e, L6e: 40 %

Category L3e: 50 %

Category L4e: 46 %

Categories L5e, L7e: 44 %

Category L (rear wheel brake):

all categories: 25 % of the total vehicle mass

X |

Less than 50 % of the above values reached. | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.3.1. Performance

If the secondary braking system is separate from the service braking system, use the method specified in 1.2.1. |

(a)

Inadequate braking effort on one or more wheels.

X |

No braking effort on one or more wheels. | | | X

(b)

Braking effort from any wheel is less than 70 % of the maximum effort recorded from another wheel on the same axle specified. Or, in the case of testing on the road, the vehicle deviates excessively from a straight line.

X |

Braking effort from any wheel is less than 50 % of the maximum effort recorded from the other wheel on the same axle in the case of steered axles. | | | X

(c)

No gradual variation in brake effort (grabbing).

X |

1.3.2. Efficiency

If the secondary braking system is separate from the service braking system, use the method specified in 1.2.2. | Braking effort less than 50 % (6) of the service brake performance defined in section 1.2.2 in relation to the maximum authorized mass. | | X |

Less than 50 % of the above braking effort values reached. | | | X

1.4.1. Performance

Apply the brake during a test on a brake tester. | Brake inoperative on one side or, in the case of testing on the road, the vehicle deviates excessively from a straight line. | | X |

Less than 50 % of the braking effort values as referred to in point 1.4.2 reached in relation to the vehicle mass during testing. | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.4.2. Efficiency

Test with a brake tester. If not possible, then by a road test using either an indicating or deceleration recording instrument or with the vehicle on a slope of known gradient. | Does not give, for all vehicles, a braking ratio of at least 16 % in relation to the maximum authorized mass or, for motor vehicles, of at least 12 % in relation to the maximum authorised combination mass of the vehicle, whichever is the greater. | | X |

Less than 50 % of the above braking effort values reached. | | | X

1.5. Endurance braking system performance

Visual inspection and, where possible, test whether the system functions. |

(a)

No gradual variation of efficiency (not applicable to exhaust brake systems).

X |

(b)

System not functioning.

X |

1.6. Anti-lock braking system (ABS)

Visual inspection and inspection of warning device and/or using electronic vehicle interface. |

(a)

Warning device malfunctioning.

X |

(b)

Warning device shows system malfunction.

X |

(c)

Wheel speed sensors missing or damaged.

X |

(d)

Wirings damaged.

X |

(e)

Other components missing or damaged.

X |

(f)

System indicates failure via the electronic vehicle interface.

X |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

1.7. Electronic brake system (EBS)

Visual inspection and inspection of warning device and/or using electronic vehicle interface. |

(a)

Warning device malfunctioning.

X |

(b)

Warning device shows system malfunction.

X |

(c)

System indicates failure via the electronic vehicle interface.

X |

1.8. Brake fluid

Visual inspection | Brake fluid contaminated or sedimented. | | X |

Imminent risk of failure. | | | X

2.1.1. Steering gear condition

With the vehicle over a pit or on a hoist and with the road wheels off the ground or on turntables, rotate the steering wheel from lock to lock. Visual inspection of the operation of the steering gear. |

(a)

Roughness in operation of gear.

X |

(b)

Sector shaft twisted or splines worn.

X |

Affecting functionality. | | | X

(c)

Excessive wear in sector shaft.

X |

Affecting functionality. | | | X

(d)

Excessive movement of sector shaft.

X |

Affecting functionality. | | | X

(e)

Leaking.

X | |

Formation of drops. | | X |

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

2.1.2. Steering gear casing attachment

With vehicle on a pit or hoist and the weight of the vehicle road wheels on the ground, rotate steering/handle bar wheel clockwise and anticlockwise or using a specially adapted wheel play detector. Visual inspection of the attachment of gear casing to chassis. |

(a)

Steering gear casing not properly attached.

X |

Attachments dangerously loose or relative movement to chassis/bodywork visible. | | | X

(b)

Elongated fixing holes in chassis.

X |

Attachments seriously affected. | | | X

(c)

Missing or fractured fixing bolts.

X |

Attachments seriously affected. | | | X

(d)

Steering gear casing fractured.

X |

Stability or attachment of casing affected. | | | X

2.1.3. Steering linkage condition

With the vehicle over a pit or on a hoist and with the road wheel on the ground, rock steering wheel clockwise and anti- clockwise or using a specially adapted wheel play detector. Visual inspection of steering components for wear, fractures and security. |

(a)

Relative movement between components which should be fixed.

X |

Excessive movement or likely to unlink. | | | X

(b)

Excessive wear at joints.

X |

A very serious risk of unlinking. | | | X

(c)

Fractures or deformation of any component.

X |

Affecting function. | | | X

(d)

Absence of locking devices.

X |

(e)

Misalignment of components (e.g. track rod or drag link).

X |

(f)

Unsafe modification3.

X |

Affecting function. | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

(g)

Dust cover damaged or deteriorated.

X | |

Dust cover missing or severely deteriorated. | | X |

2.1.4. Steering linkage operation

With the vehicle over a pit or on a hoist and with the road wheel on the ground, rock steering wheel clockwise and anti-clockwise or using a specially adapted wheel play detector. Visual inspection of steering components for wear, fractures and security. |

(a)

Moving steering linkage fouling a fixed part of the chassis.

X |

(b)

Steering stops not operating or missing.

X |

2.1.5. Power steering

Check steering system for leaks and hydraulic fluid reservoir level (if visible). With the road wheels on the ground and with the engine running, check that the power steering system is operating. |

(a)

Fluid leak or functions affected.

X |

(b)

Insufficient fluid (below MIN mark).

X | |

Insufficient reservoir. | | X |

(c)

Mechanism not working.

X |

Steering affected. | | | X

(d)

Mechanism fractured or insecure.

X |

Steering affected. | | | X

(e)

Misalignment or fouling of components.

X |

Steering affected. | | | X

(f)

Unsafe modification3.

X |

Steering affected. | | | X

Item | Method | Reasons for failure | Assessment of deficiencies

Minor | Major | Dangerous

(g)

Cables/hoses damaged, excessively corroded.

X |

Steering affected. | | | X

2.2.1. Steering wheel/handle bar condition

With the vehicle over a pit or on a hoist and the mass of the vehicle on the ground, push and pull the steering wheel in line with column, push steering wheel/handle bar in various directions at right angles to the column/forks. Visual inspection of play, and condition of flexible couplings or universal joints. |

(a)

Relative movement between steering wheel and column indicating looseness.

X |

Very serious risk of unlinking. | | | X

(b)

Absence of retaining device on steering wheel hub.

X |

Very serious risk of unlinking. | | | X

(c)

Fracture or looseness of steering wheel hub, rim or spokes.

X |

Very serious risk of unlinking. | | | X

2.2.2. Steering column/yokes and forks and steering dampers

This article is long: the rest is at the official publication.